Version 32.16 by Xiaoling on 2022/06/07 11:41
Show last authors
1 (% style="text-align:center" %)
2 [[image:image-20220606151504-2.jpeg||height="554" width="554"]]
3
4
5
6 **Contents:**
7
8 {{toc/}}
9
10
11
12
13
14
15 = 1. Introduction =
16
17 == 1.1 ​What is LoRaWAN Soil Moisture & EC Sensor ==
18
19 (((
20 The Dragino LSE01 is a (% style="color:#4f81bd" %)**LoRaWAN Soil Moisture & EC Sensor**(%%) for IoT of Agriculture. It is designed to measure the soil moisture of saline-alkali soil and loamy soil. The soil sensor uses FDR method to calculate the soil moisture with the compensation from soil temperature and conductivity. It also has been calibrated in factory for Mineral soil type.
21 )))
22
23 (((
24 It detects (% style="color:#4f81bd" %)**Soil Moisture**(%%), (% style="color:#4f81bd" %)**Soil Temperature**(%%) and (% style="color:#4f81bd" %)**Soil Conductivity**(%%), and uploads the value via wireless to LoRaWAN IoT Server.
25 )))
26
27 (((
28 The LoRa wireless technology used in LES01 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
29 )))
30
31 (((
32 LES01 is powered by (% style="color:#4f81bd" %)**4000mA or 8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 10 years.
33 )))
34
35 (((
36 Each LES01 is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
37 )))
38
39
40 [[image:1654503236291-817.png]]
41
42
43 [[image:1654503265560-120.png]]
44
45
46
47 == 1.2 ​Features ==
48
49 * LoRaWAN 1.0.3 Class A
50 * Ultra low power consumption
51 * Monitor Soil Moisture
52 * Monitor Soil Temperature
53 * Monitor Soil Conductivity
54 * Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
55 * AT Commands to change parameters
56 * Uplink on periodically
57 * Downlink to change configure
58 * IP66 Waterproof Enclosure
59 * 4000mAh or 8500mAh Battery for long term use
60
61 == 1.3 Specification ==
62
63 Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
64
65 [[image:image-20220606162220-5.png]]
66
67
68
69 == ​1.4 Applications ==
70
71 * Smart Agriculture
72
73 (% class="wikigeneratedid" id="H200B1.5FirmwareChangelog" %)
74 ​
75
76 == 1.5 Firmware Change log ==
77
78
79 **LSE01 v1.0 :**  Release
80
81
82
83 = 2. Configure LSE01 to connect to LoRaWAN network =
84
85 == 2.1 How it works ==
86
87 (((
88 The LSE01 is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and power on the LSE0150. It will automatically join the network via OTAA and start to send the sensor value
89 )))
90
91 (((
92 In case you can’t set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands >>||anchor="H3.200BUsingtheATCommands"]].
93 )))
94
95
96
97 == 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
98
99 Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LG308>>url:http://www.dragino.com/products/lora/item/140-lg308.html]] as a LoRaWAN gateway in this example.
100
101
102 [[image:1654503992078-669.png]]
103
104
105 The LG308 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
106
107
108 **Step 1**: Create a device in TTN with the OTAA keys from LSE01.
109
110 Each LSE01 is shipped with a sticker with the default device EUI as below:
111
112 [[image:image-20220606163732-6.jpeg]]
113
114 You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
115
116 **Add APP EUI in the application**
117
118
119 [[image:1654504596150-405.png]]
120
121
122
123 **Add APP KEY and DEV EUI**
124
125 [[image:1654504683289-357.png]]
126
127
128
129 **Step 2**: Power on LSE01
130
131
132 Put a Jumper on JP2 to power on the device. ( The Jumper must be in FLASH position).
133
134 [[image:image-20220606163915-7.png]]
135
136
137 **Step 3:** The LSE01 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel.
138
139 [[image:1654504778294-788.png]]
140
141
142
143 == 2.3 Uplink Payload ==
144
145 (% class="wikigeneratedid" %)
146 === ===
147
148 === 2.3.1 MOD~=0(Default Mode) ===
149
150 LSE01 will uplink payload via LoRaWAN with below payload format: 
151
152 (((
153 Uplink payload includes in total 11 bytes.
154 )))
155
156 (% border="1" cellspacing="10" style="background-color:#ffffcc; width:500px" %)
157 |(((
158 **Size**
159
160 **(bytes)**
161 )))|**2**|**2**|**2**|**2**|**2**|**1**
162 |**Value**|[[BAT>>||anchor="H2.3.3BatteryInfo"]]|(((
163 Temperature
164
165 (Reserve, Ignore now)
166 )))|[[Soil Moisture>>||anchor="H2.3.4SoilMoisture"]]|[[Soil Temperature>>||anchor="H2.3.5SoilTemperature"]]|[[Soil Conductivity (EC)>>||anchor="H2.3.6SoilConductivity28EC29"]]|(((
167 MOD & Digital Interrupt
168
169 (Optional)
170 )))
171
172
173
174 === 2.3.2 MOD~=1(Original value) ===
175
176 This mode can get the original AD value of moisture and original conductivity (with temperature drift compensation).
177
178 (% border="1" cellspacing="10" style="background-color:#ffffcc; width:500px" %)
179 |(((
180 **Size**
181
182 **(bytes)**
183 )))|**2**|**2**|**2**|**2**|**2**|**1**
184 |**Value**|[[BAT>>||anchor="H2.3.3BatteryInfo"]]|(((
185 Temperature
186
187 (Reserve, Ignore now)
188 )))|[[Soil Moisture>>||anchor="H2.3.4SoilMoisture"]](raw)|[[Soil Temperature>>||anchor="H2.3.5SoilTemperature"]]|[[Soil Conductivity (EC)>>||anchor="H2.3.6SoilConductivity28EC29"]](raw)|(((
189 MOD & Digital Interrupt
190
191 (Optional)
192 )))
193
194
195
196 === 2.3.3 Battery Info ===
197
198 (((
199 Check the battery voltage for LSE01.
200 )))
201
202 (((
203 Ex1: 0x0B45 = 2885mV
204 )))
205
206 (((
207 Ex2: 0x0B49 = 2889mV
208 )))
209
210
211
212 === 2.3.4 Soil Moisture ===
213
214 (((
215 Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
216 )))
217
218 (((
219 For example, if the data you get from the register is __0x05 0xDC__, the moisture content in the soil is
220 )))
221
222 (((
223
224 )))
225
226 (((
227 (% style="color:#4f81bd" %)**05DC(H) = 1500(D) /100 = 15%.**
228 )))
229
230
231
232 === 2.3.5 Soil Temperature ===
233
234 (((
235 Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is 0x09 0xEC, the temperature content in the soil is
236 )))
237
238 (((
239 **Example**:
240 )))
241
242 (((
243 If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/100 = 2.61 °C
244 )))
245
246 (((
247 If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/100 = -1.29 °C
248 )))
249
250
251
252 === 2.3.6 Soil Conductivity (EC) ===
253
254 (((
255 Obtain (% style="color:#4f81bd" %)**__soluble salt concentration__**(%%) in soil or (% style="color:#4f81bd" %)**__soluble ion concentration in liquid fertilizer__**(%%) or (% style="color:#4f81bd" %)**__planting medium__**(%%). The value range of the register is 0 - 20000(Decimal)( Can be greater than 20000).
256 )))
257
258 (((
259 For example, if the data you get from the register is 0x00 0xC8, the soil conductivity is 00C8(H) = 200(D) = 200 uS/cm.
260 )))
261
262 (((
263 Generally, the EC value of irrigation water is less than 800uS / cm.
264 )))
265
266 (((
267
268 )))
269
270 (((
271
272 )))
273
274 === 2.3.7 MOD ===
275
276 Firmware version at least v2.1 supports changing mode.
277
278 For example, bytes[10]=90
279
280 mod=(bytes[10]>>7)&0x01=1.
281
282
283 **Downlink Command:**
284
285 If payload = 0x0A00, workmode=0
286
287 If** **payload =** **0x0A01, workmode=1
288
289
290
291 === 2.3.8 ​Decode payload in The Things Network ===
292
293 While using TTN network, you can add the payload format to decode the payload.
294
295
296 [[image:1654505570700-128.png]]
297
298 (((
299 The payload decoder function for TTN is here:
300 )))
301
302 (((
303 LSE01 TTN Payload Decoder: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/]]
304 )))
305
306
307
308 == 2.4 Uplink Interval ==
309
310 The LSE01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H4.1ChangeUplinkInterval"]]
311
312
313
314 == 2.5 Downlink Payload ==
315
316 By default, LSE50 prints the downlink payload to console port.
317
318 [[image:image-20220606165544-8.png]]
319
320
321 (((
322 **Examples:**
323 )))
324
325 (((
326
327 )))
328
329 * (((
330 **Set TDC**
331 )))
332
333 (((
334 If the payload=0100003C, it means set the END Node’s TDC to 0x00003C=60(S), while type code is 01.
335 )))
336
337 (((
338 Payload:    01 00 00 1E    TDC=30S
339 )))
340
341 (((
342 Payload:    01 00 00 3C    TDC=60S
343 )))
344
345 (((
346
347 )))
348
349 * (((
350 **Reset**
351 )))
352
353 (((
354 If payload = 0x04FF, it will reset the LSE01
355 )))
356
357
358 * **CFM**
359
360 Downlink Payload: 05000001, Set AT+CFM=1 or 05000000 , set AT+CFM=0
361
362
363
364 == 2.6 ​Show Data in DataCake IoT Server ==
365
366 (((
367 [[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
368 )))
369
370 (((
371
372 )))
373
374 (((
375 **Step 1**: Be sure that your device is programmed and properly connected to the network at this time.
376 )))
377
378 (((
379 **Step 2**: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
380 )))
381
382
383 [[image:1654505857935-743.png]]
384
385
386 [[image:1654505874829-548.png]]
387
388 Step 3: Create an account or log in Datacake.
389
390 Step 4: Search the LSE01 and add DevEUI.
391
392
393 [[image:1654505905236-553.png]]
394
395
396 After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
397
398 [[image:1654505925508-181.png]]
399
400
401
402 == 2.7 Frequency Plans ==
403
404 The LSE01 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
405
406
407 === 2.7.1 EU863-870 (EU868) ===
408
409 (% style="color:#037691" %)** Uplink:**
410
411 868.1 - SF7BW125 to SF12BW125
412
413 868.3 - SF7BW125 to SF12BW125 and SF7BW250
414
415 868.5 - SF7BW125 to SF12BW125
416
417 867.1 - SF7BW125 to SF12BW125
418
419 867.3 - SF7BW125 to SF12BW125
420
421 867.5 - SF7BW125 to SF12BW125
422
423 867.7 - SF7BW125 to SF12BW125
424
425 867.9 - SF7BW125 to SF12BW125
426
427 868.8 - FSK
428
429
430 (% style="color:#037691" %)** Downlink:**
431
432 Uplink channels 1-9 (RX1)
433
434 869.525 - SF9BW125 (RX2 downlink only)
435
436
437
438 === 2.7.2 US902-928(US915) ===
439
440 Used in USA, Canada and South America. Default use CHE=2
441
442 (% style="color:#037691" %)**Uplink:**
443
444 903.9 - SF7BW125 to SF10BW125
445
446 904.1 - SF7BW125 to SF10BW125
447
448 904.3 - SF7BW125 to SF10BW125
449
450 904.5 - SF7BW125 to SF10BW125
451
452 904.7 - SF7BW125 to SF10BW125
453
454 904.9 - SF7BW125 to SF10BW125
455
456 905.1 - SF7BW125 to SF10BW125
457
458 905.3 - SF7BW125 to SF10BW125
459
460
461 (% style="color:#037691" %)**Downlink:**
462
463 923.3 - SF7BW500 to SF12BW500
464
465 923.9 - SF7BW500 to SF12BW500
466
467 924.5 - SF7BW500 to SF12BW500
468
469 925.1 - SF7BW500 to SF12BW500
470
471 925.7 - SF7BW500 to SF12BW500
472
473 926.3 - SF7BW500 to SF12BW500
474
475 926.9 - SF7BW500 to SF12BW500
476
477 927.5 - SF7BW500 to SF12BW500
478
479 923.3 - SF12BW500(RX2 downlink only)
480
481
482
483 === 2.7.3 CN470-510 (CN470) ===
484
485 Used in China, Default use CHE=1
486
487 (% style="color:#037691" %)**Uplink:**
488
489 486.3 - SF7BW125 to SF12BW125
490
491 486.5 - SF7BW125 to SF12BW125
492
493 486.7 - SF7BW125 to SF12BW125
494
495 486.9 - SF7BW125 to SF12BW125
496
497 487.1 - SF7BW125 to SF12BW125
498
499 487.3 - SF7BW125 to SF12BW125
500
501 487.5 - SF7BW125 to SF12BW125
502
503 487.7 - SF7BW125 to SF12BW125
504
505
506 (% style="color:#037691" %)**Downlink:**
507
508 506.7 - SF7BW125 to SF12BW125
509
510 506.9 - SF7BW125 to SF12BW125
511
512 507.1 - SF7BW125 to SF12BW125
513
514 507.3 - SF7BW125 to SF12BW125
515
516 507.5 - SF7BW125 to SF12BW125
517
518 507.7 - SF7BW125 to SF12BW125
519
520 507.9 - SF7BW125 to SF12BW125
521
522 508.1 - SF7BW125 to SF12BW125
523
524 505.3 - SF12BW125 (RX2 downlink only)
525
526
527
528 === 2.7.4 AU915-928(AU915) ===
529
530 Default use CHE=2
531
532 (% style="color:#037691" %)**Uplink:**
533
534 916.8 - SF7BW125 to SF12BW125
535
536 917.0 - SF7BW125 to SF12BW125
537
538 917.2 - SF7BW125 to SF12BW125
539
540 917.4 - SF7BW125 to SF12BW125
541
542 917.6 - SF7BW125 to SF12BW125
543
544 917.8 - SF7BW125 to SF12BW125
545
546 918.0 - SF7BW125 to SF12BW125
547
548 918.2 - SF7BW125 to SF12BW125
549
550
551 (% style="color:#037691" %)**Downlink:**
552
553 923.3 - SF7BW500 to SF12BW500
554
555 923.9 - SF7BW500 to SF12BW500
556
557 924.5 - SF7BW500 to SF12BW500
558
559 925.1 - SF7BW500 to SF12BW500
560
561 925.7 - SF7BW500 to SF12BW500
562
563 926.3 - SF7BW500 to SF12BW500
564
565 926.9 - SF7BW500 to SF12BW500
566
567 927.5 - SF7BW500 to SF12BW500
568
569 923.3 - SF12BW500(RX2 downlink only)
570
571
572
573 === 2.7.5 AS920-923 & AS923-925 (AS923) ===
574
575 (% style="color:#037691" %)**Default Uplink channel:**
576
577 923.2 - SF7BW125 to SF10BW125
578
579 923.4 - SF7BW125 to SF10BW125
580
581
582 (% style="color:#037691" %)**Additional Uplink Channel**:
583
584 (OTAA mode, channel added by JoinAccept message)
585
586 (% style="color:#037691" %)**AS920~~AS923 for Japan, Malaysia, Singapore**:
587
588 922.2 - SF7BW125 to SF10BW125
589
590 922.4 - SF7BW125 to SF10BW125
591
592 922.6 - SF7BW125 to SF10BW125
593
594 922.8 - SF7BW125 to SF10BW125
595
596 923.0 - SF7BW125 to SF10BW125
597
598 922.0 - SF7BW125 to SF10BW125
599
600
601 (% style="color:#037691" %)**AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam**:
602
603 923.6 - SF7BW125 to SF10BW125
604
605 923.8 - SF7BW125 to SF10BW125
606
607 924.0 - SF7BW125 to SF10BW125
608
609 924.2 - SF7BW125 to SF10BW125
610
611 924.4 - SF7BW125 to SF10BW125
612
613 924.6 - SF7BW125 to SF10BW125
614
615
616 (% style="color:#037691" %)** Downlink:**
617
618 Uplink channels 1-8 (RX1)
619
620 923.2 - SF10BW125 (RX2)
621
622
623
624 === 2.7.6 KR920-923 (KR920) ===
625
626 Default channel:
627
628 922.1 - SF7BW125 to SF12BW125
629
630 922.3 - SF7BW125 to SF12BW125
631
632 922.5 - SF7BW125 to SF12BW125
633
634
635 (% style="color:#037691" %)**Uplink: (OTAA mode, channel added by JoinAccept message)**
636
637 922.1 - SF7BW125 to SF12BW125
638
639 922.3 - SF7BW125 to SF12BW125
640
641 922.5 - SF7BW125 to SF12BW125
642
643 922.7 - SF7BW125 to SF12BW125
644
645 922.9 - SF7BW125 to SF12BW125
646
647 923.1 - SF7BW125 to SF12BW125
648
649 923.3 - SF7BW125 to SF12BW125
650
651
652 (% style="color:#037691" %)**Downlink:**
653
654 Uplink channels 1-7(RX1)
655
656 921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
657
658
659
660 === 2.7.7 IN865-867 (IN865) ===
661
662 (% style="color:#037691" %)** Uplink:**
663
664 865.0625 - SF7BW125 to SF12BW125
665
666 865.4025 - SF7BW125 to SF12BW125
667
668 865.9850 - SF7BW125 to SF12BW125
669
670
671 (% style="color:#037691" %) **Downlink:**
672
673 Uplink channels 1-3 (RX1)
674
675 866.550 - SF10BW125 (RX2)
676
677
678
679
680 == 2.8 LED Indicator ==
681
682 The LSE01 has an internal LED which is to show the status of different state.
683
684 * Blink once when device power on.
685 * Solid ON for 5 seconds once device successful Join the network.
686 * Blink once when device transmit a packet.
687
688
689
690 == 2.9 Installation in Soil ==
691
692 **Measurement the soil surface**
693
694
695 [[image:1654506634463-199.png]] ​
696
697 (((
698 (((
699 Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting.
700 )))
701 )))
702
703
704 [[image:1654506665940-119.png]]
705
706 (((
707 Dig a hole with diameter > 20CM.
708 )))
709
710 (((
711 Horizontal insert the probe to the soil and fill the hole for long term measurement.
712 )))
713
714
715 == 2.10 ​Firmware Change Log ==
716
717 (((
718 **Firmware download link:**
719 )))
720
721 (((
722 [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
723 )))
724
725 (((
726
727 )))
728
729 (((
730 **Firmware Upgrade Method: **[[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]
731 )))
732
733 (((
734
735 )))
736
737 (((
738 **V1.0.**
739 )))
740
741 (((
742 Release
743 )))
744
745
746 == 2.11 ​Battery Analysis ==
747
748 === 2.11.1 ​Battery Type ===
749
750 (((
751 The LSE01 battery is a combination of a 4000mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
752 )))
753
754 (((
755 The battery is designed to last for more than 5 years for the LSN50.
756 )))
757
758 (((
759 (((
760 The battery-related documents are as below:
761 )))
762 )))
763
764 * (((
765 [[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
766 )))
767 * (((
768 [[Lithium-Thionyl Chloride Battery  datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]],
769 )))
770 * (((
771 [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
772 )))
773
774 [[image:image-20220606171726-9.png]]
775
776
777
778 === 2.11.2 ​Battery Note ===
779
780 (((
781 The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
782 )))
783
784
785
786 === 2.11.3 Replace the battery ===
787
788 (((
789 If Battery is lower than 2.7v, user should replace the battery of LSE01.
790 )))
791
792 (((
793 You can change the battery in the LSE01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
794 )))
795
796 (((
797 The default battery pack of LSE01 includes a ER18505 plus super capacitor. If user can’t find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
798 )))
799
800
801
802 = 3. ​Using the AT Commands =
803
804 == 3.1 Access AT Commands ==
805
806
807 LSE01 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSE01 for using AT command, as below.
808
809 [[image:1654501986557-872.png||height="391" width="800"]]
810
811
812 Or if you have below board, use below connection:
813
814
815 [[image:1654502005655-729.png||height="503" width="801"]]
816
817
818
819 In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LSE01. LSE01 will output system info once power on as below:
820
821
822 [[image:1654502050864-459.png||height="564" width="806"]]
823
824
825 Below are the available commands, a more detailed AT Command manual can be found at [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]]: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]]
826
827
828 (% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>? **(%%) : Help on <CMD>
829
830 (% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD> **(%%) : Run <CMD>
831
832 (% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>=<value>**(%%) : Set the value
833
834 (% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>=?**(%%)  : Get the value
835
836
837 (% style="color:#037691" %)**General Commands**(%%)      
838
839 (% style="background-color:#dcdcdc" %)**AT**(%%)  : Attention       
840
841 (% style="background-color:#dcdcdc" %)**AT?**(%%)  : Short Help     
842
843 (% style="background-color:#dcdcdc" %)**ATZ**(%%)  : MCU Reset    
844
845 (% style="background-color:#dcdcdc" %)**AT+TDC**(%%)  : Application Data Transmission Interval 
846
847
848 (% style="color:#037691" %)**Keys, IDs and EUIs management**
849
850 (% style="background-color:#dcdcdc" %)**AT+APPEUI**(%%)              : Application EUI      
851
852 (% style="background-color:#dcdcdc" %)**AT+APPKEY**(%%)              : Application Key     
853
854 (% style="background-color:#dcdcdc" %)**AT+APPSKEY**(%%)            : Application Session Key
855
856 (% style="background-color:#dcdcdc" %)**AT+DADDR**(%%)              : Device Address     
857
858 (% style="background-color:#dcdcdc" %)**AT+DEUI**(%%)                   : Device EUI     
859
860 (% style="background-color:#dcdcdc" %)**AT+NWKID**(%%)               : Network ID (You can enter this command change only after successful network connection) 
861
862 (% style="background-color:#dcdcdc" %)**AT+NWKSKEY**(%%)          : Network Session Key Joining and sending date on LoRa network  
863
864 (% style="background-color:#dcdcdc" %)**AT+CFM**(%%)  : Confirm Mode       
865
866 (% style="background-color:#dcdcdc" %)**AT+CFS**(%%)                     : Confirm Status       
867
868 (% style="background-color:#dcdcdc" %)**AT+JOIN**(%%)  : Join LoRa? Network       
869
870 (% style="background-color:#dcdcdc" %)**AT+NJM**(%%)  : LoRa? Network Join Mode    
871
872 (% style="background-color:#dcdcdc" %)**AT+NJS**(%%)                     : LoRa? Network Join Status    
873
874 (% style="background-color:#dcdcdc" %)**AT+RECV**(%%)                  : Print Last Received Data in Raw Format
875
876 (% style="background-color:#dcdcdc" %)**AT+RECVB**(%%)                : Print Last Received Data in Binary Format      
877
878 (% style="background-color:#dcdcdc" %)**AT+SEND**(%%)                  : Send Text Data      
879
880 (% style="background-color:#dcdcdc" %)**AT+SENB**(%%)                  : Send Hexadecimal Data
881
882
883 (% style="color:#037691" %)**LoRa Network Management**
884
885 (% style="background-color:#dcdcdc" %)**AT+ADR**(%%)          : Adaptive Rate
886
887 (% style="background-color:#dcdcdc" %)**AT+CLASS**(%%)  : LoRa Class(Currently only support class A
888
889 (% style="background-color:#dcdcdc" %)**AT+DCS**(%%)  : Duty Cycle Setting 
890
891 (% style="background-color:#dcdcdc" %)**AT+DR**(%%)  : Data Rate (Can Only be Modified after ADR=0)     
892
893 (% style="background-color:#dcdcdc" %)**AT+FCD**(%%)  : Frame Counter Downlink       
894
895 (% style="background-color:#dcdcdc" %)**AT+FCU**(%%)  : Frame Counter Uplink   
896
897 (% style="background-color:#dcdcdc" %)**AT+JN1DL**(%%)  : Join Accept Delay1
898
899 (% style="background-color:#dcdcdc" %)**AT+JN2DL**(%%)  : Join Accept Delay2
900
901 (% style="background-color:#dcdcdc" %)**AT+PNM**(%%)  : Public Network Mode   
902
903 (% style="background-color:#dcdcdc" %)**AT+RX1DL**(%%)  : Receive Delay1      
904
905 (% style="background-color:#dcdcdc" %)**AT+RX2DL**(%%)  : Receive Delay2      
906
907 (% style="background-color:#dcdcdc" %)**AT+RX2DR**(%%)  : Rx2 Window Data Rate 
908
909 (% style="background-color:#dcdcdc" %)**AT+RX2FQ**(%%)  : Rx2 Window Frequency
910
911 (% style="background-color:#dcdcdc" %)**AT+TXP**(%%)  : Transmit Power
912
913 (% style="background-color:#dcdcdc" %)**AT+ MOD**(%%)  : Set work mode
914
915
916 (% style="color:#037691" %)**Information** 
917
918 (% style="background-color:#dcdcdc" %)**AT+RSSI**(%%)           : RSSI of the Last Received Packet   
919
920 (% style="background-color:#dcdcdc" %)**AT+SNR**(%%)           : SNR of the Last Received Packet   
921
922 (% style="background-color:#dcdcdc" %)**AT+VER**(%%)           : Image Version and Frequency Band       
923
924 (% style="background-color:#dcdcdc" %)**AT+FDR**(%%)           : Factory Data Reset
925
926 (% style="background-color:#dcdcdc" %)**AT+PORT**(%%)  : Application Port    
927
928 (% style="background-color:#dcdcdc" %)**AT+CHS**(%%)  : Get or Set Frequency (Unit: Hz) for Single Channel Mode
929
930 (% style="background-color:#dcdcdc" %)**AT+CHE**(%%)  : Get or Set eight channels mode, Only for US915, AU915, CN470
931
932
933 = ​4. FAQ =
934
935 == 4.1 ​How to change the LoRa Frequency Bands/Region? ==
936
937 (((
938 You can follow the instructions for [[how to upgrade image>>||anchor="H2.10200BFirmwareChangeLog"]].
939 When downloading the images, choose the required image file for download. ​
940 )))
941
942 (((
943
944 )))
945
946 (((
947 How to set up LSE01 to work in 8 channel mode By default, the frequency bands US915, AU915, CN470 work in 72 frequencies. Many gateways are 8 channel gateways, and in this case, the OTAA join time and uplink schedule is long and unpredictable while the end node is hopping in 72 frequencies.
948 )))
949
950 (((
951
952 )))
953
954 (((
955 You can configure the end node to work in 8 channel mode by using the AT+CHE command. The 500kHz channels are always included for OTAA.
956 )))
957
958 (((
959
960 )))
961
962 (((
963 For example, in **US915** band, the frequency table is as below. By default, the end node will use all channels (0~~71) for OTAA Join process. After the OTAA Join, the end node will use these all channels (0~~71) to send uplink packets.
964 )))
965
966 [[image:image-20220606154726-3.png]]
967
968
969 When you use the TTN network, the US915 frequency bands use are:
970
971 * 903.9 - SF7BW125 to SF10BW125
972 * 904.1 - SF7BW125 to SF10BW125
973 * 904.3 - SF7BW125 to SF10BW125
974 * 904.5 - SF7BW125 to SF10BW125
975 * 904.7 - SF7BW125 to SF10BW125
976 * 904.9 - SF7BW125 to SF10BW125
977 * 905.1 - SF7BW125 to SF10BW125
978 * 905.3 - SF7BW125 to SF10BW125
979 * 904.6 - SF8BW500
980
981 (((
982 Because the end node is now hopping in 72 frequency, it makes it difficult for the devices to Join the TTN network and uplink data. To solve this issue, you can access the device via the AT commands and run:
983 )))
984
985 (% class="box infomessage" %)
986 (((
987 **AT+CHE=2**
988 )))
989
990 (% class="box infomessage" %)
991 (((
992 **ATZ**
993 )))
994
995 (((
996 to set the end node to work in 8 channel mode. The device will work in Channel 8-15 & 64-71 for OTAA, and channel 8-15 for Uplink.
997 )))
998
999 (((
1000
1001 )))
1002
1003 (((
1004 The **AU915** band is similar. Below are the AU915 Uplink Channels.
1005 )))
1006
1007 [[image:image-20220606154825-4.png]]
1008
1009
1010
1011 = 5. Trouble Shooting =
1012
1013 == 5.1 ​Why I can’t join TTN in US915 / AU915 bands? ==
1014
1015 It is due to channel mapping. Please see the [[Eight Channel Mode>>doc:Main.LoRaWAN Communication Debug.WebHome||anchor="H2.NoticeofUS9152FCN4702FAU915Frequencyband"]] section above for details.
1016
1017
1018 == 5.2 AT Command input doesn’t work ==
1019
1020 (((
1021 In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1022 )))
1023
1024
1025 == 5.3 Device rejoin in at the second uplink packet ==
1026
1027 (% style="color:#4f81bd" %)**Issue describe as below:**
1028
1029 [[image:1654500909990-784.png]]
1030
1031
1032 (% style="color:#4f81bd" %)**Cause for this issue:**
1033
1034 (((
1035 The fuse on LSE01 is not large enough, some of the soil probe require large current up to 5v 800mA, in a short pulse. When this happen, it cause the device reboot so user see rejoin.
1036 )))
1037
1038
1039 (% style="color:#4f81bd" %)**Solution: **
1040
1041 All new shipped LSE01 after 2020-May-30 will have this to fix. For the customer who see this issue, please bypass the fuse as below:
1042
1043 [[image:1654500929571-736.png||height="458" width="832"]]
1044
1045
1046 = 6. ​Order Info =
1047
1048
1049 Part Number**:** (% style="color:#4f81bd" %)**LSE01-XX-YY**
1050
1051
1052 (% style="color:#4f81bd" %)**XX**(%%)**:** The default frequency band
1053
1054 * (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
1055 * (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
1056 * (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band
1057 * (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
1058 * (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
1059 * (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
1060 * (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
1061 * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
1062
1063 (% style="color:#4f81bd" %)**YY**(%%)**: **Battery Option
1064
1065 * (% style="color:red" %)**4**(%%): 4000mAh battery
1066 * (% style="color:red" %)**8**(%%): 8500mAh battery
1067
1068 (% class="wikigeneratedid" %)
1069 (((
1070
1071 )))
1072
1073 = 7. Packing Info =
1074
1075 (((
1076
1077
1078 (% style="color:#037691" %)**Package Includes**:
1079 )))
1080
1081 * (((
1082 LSE01 LoRaWAN Soil Moisture & EC Sensor x 1
1083 )))
1084
1085 (((
1086
1087
1088 (% style="color:#037691" %)**Dimension and weight**:
1089 )))
1090
1091 * (((
1092 Device Size: cm
1093 )))
1094 * (((
1095 Device Weight: g
1096 )))
1097 * (((
1098 Package Size / pcs : cm
1099 )))
1100 * (((
1101 Weight / pcs : g
1102
1103
1104 )))
1105
1106 = 8. Support =
1107
1108 * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
1109 * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
1110
1111

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0