Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -54,18 +54,33 @@
54	54	[[image:image-20220530002453-3.png||height="262" width="493"]]
55	55
56	56
	57	+= Configure GroPoint Air to Connect LoRaWAN Network =
	58	+
	59	+
	60	+== LED Indicator  ( 检查等状态是否对的) ==
	61	+
	62	+The GroPoint Air has an internal LED which can show the status of different states.
	63	+
	64	+* The sensor is detected when the device is turned on, and it will flash 4 times quickly when it is detected.
	65	+* Blink once when device transmits a packet.
	66	+
	67	+
	68	+== Firmware and Changelog (Changelog标注现在 版本是什么版本) ==
	69	+
	70	+Firmware Download Location: [[https:~~/~~/www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0>>https://www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0]]
	71	+
	72	+Change Log:
	73	+
	74	+
	75	+
57	57	= Configure GroPoint Air via AT Command or LoRaWAN Downlink =
58	58
59	59	Use can configure GroPoint Air via AT Command or LoRaWAN Downlink.
60	60
61		-* (((
62		-AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]].
63		-)))
64		-* (((
65		-LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]]
66		-)))
	80	+* AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]].
	81	+* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]]
67	67
68		-There are two kinds of commands to configure GroPoint, they are:
	83	+There are two kinds of commands to configure GroPoint Air, they are:
69	69
70	70	* (((
71	71	**~ General Commands**.
...	...	@@ -73,21 +73,17 @@
73	73
74	74	These commands are to configure:
75	75
76		-* (((
77		-General system settings like: uplink interval.
78		-)))
79		-* (((
80		-LoRaWAN protocol & radio-related command.
81		-)))
	91	+* General system settings like: uplink interval.
	92	+* LoRaWAN protocol & radio-related command.
82	82
83	83	They are the same for all Dragino Device that support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>url:http://8.211.40.43/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
84	84
85	85
86	86	* (((
87		-**~ Commands special design for LLMS01**
	98	+**~ Commands special design for GroPoint Air**
88	88	)))
89	89
90		-These commands only valid for LLMS01, as below:
	101	+These commands only valid for GroPoint Air, as below:
91	91
92	92	== 3.1 Set Transmit Interval Time ==
93	93
...	...	@@ -103,15 +103,9 @@
103	103
104	104	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
105	105
106		-* (((
107		-Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
108		-)))
109		-* (((
110		-Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	117	+* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	118	+* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
111	111
112		-
113		-)))
114		-
115	115	== 3.2 Set Interrupt Mode  （是否存在） ==
116	116
117	117	Feature, Set Interrupt mode for GPIO_EXIT.
...	...	@@ -126,14 +126,9 @@
126	126
127	127	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
128	128
129		-* (((
130		-Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
131		-)))
132		-* (((
133		-Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
134		-)))
	134	+* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	135	+* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
135	135
136		-
137	137	== 3.3 Get Firmware Version Info ~-~--（是否存在） ==
138	138
139	139	Feature: use downlink to get firmware version.