Last modified by Xiaoling on 2024/04/23 14:37
Change comment:
There is no comment for this version
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -54,18 +54,23 @@ 54 54 [[image:image-20220530002453-3.png||height="262" width="493"]] 55 55 56 56 57 + 58 +== Firmware and Changelog: == 59 + 60 +Firmware Download Location: [[https:~~/~~/www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0>>https://www.dropbox.com/sh/4strg6w7kkekdc4/AAAUKdAV3XKhOi3t6YjA8j9za?dl=0]] 61 + 62 +Change Log: 63 + 64 + 65 + 57 57 = Configure GroPoint Air via AT Command or LoRaWAN Downlink = 58 58 59 59 Use can configure GroPoint Air via AT Command or LoRaWAN Downlink. 60 60 61 -* ((( 62 -AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]]. 63 -))) 64 -* ((( 65 -LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]] 66 -))) 70 +* AT Command Connection: See [[FAQ>>url:http://8.211.40.43/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LLMS01-LoRaWAN%20Leaf%20Moisture%20Sensor%20User%20Manual/#H6.FAQ]]. 71 +* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://8.211.40.43/xwiki/bin/view/Main/]] 67 67 68 -There are two kinds of commands to configure GroPoint, they are: 73 +There are two kinds of commands to configure GroPoint Air, they are: 69 69 70 70 * ((( 71 71 **~ General Commands**. ... ... @@ -73,21 +73,17 @@ 73 73 74 74 These commands are to configure: 75 75 76 -* ((( 77 -General system settings like: uplink interval. 78 -))) 79 -* ((( 80 -LoRaWAN protocol & radio-related command. 81 -))) 81 +* General system settings like: uplink interval. 82 +* LoRaWAN protocol & radio-related command. 82 82 83 83 They are the same for all Dragino Device that support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki: [[End Device AT Commands and Downlink Command>>url:http://8.211.40.43/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]] 84 84 85 85 86 86 * ((( 87 -**~ Commands special design for LLMS01**88 +**~ Commands special design for GroPoint Air** 88 88 ))) 89 89 90 -These commands only valid for LLMS01, as below:91 +These commands only valid for GroPoint Air, as below: 91 91 92 92 == 3.1 Set Transmit Interval Time == 93 93 ... ... @@ -103,15 +103,9 @@ 103 103 104 104 If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01. 105 105 106 -* ((( 107 -Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds 108 -))) 109 -* ((( 110 -Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds 107 +* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds 108 +* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds 111 111 112 - 113 -))) 114 - 115 115 == 3.2 Set Interrupt Mode (是否存在) == 116 116 117 117 Feature, Set Interrupt mode for GPIO_EXIT. ... ... @@ -126,14 +126,9 @@ 126 126 127 127 This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06. 128 128 129 -* ((( 130 -Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode 131 -))) 132 -* ((( 133 -Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger 134 -))) 124 +* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode 125 +* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger 135 135 136 - 137 137 == 3.3 Get Firmware Version Info ~-~--(是否存在) == 138 138 139 139 Feature: use downlink to get firmware version.