Changes for page Water Quality Sensors
Last modified by Karry Zhuang on 2025/07/18 16:37
From version 69.1
edited by Karry Zhuang
on 2025/07/15 18:48
on 2025/07/15 18:48
Change comment:
There is no comment for this version
To version 67.1
edited by Karry Zhuang
on 2025/07/15 18:00
on 2025/07/15 18:00
Change comment:
Uploaded new attachment "1752573643879-991.png", version {1}
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -948,10 +948,11 @@ 948 948 02 9A is the turbidity value, converted to decimal, it is 666, and then divided by 10, the actual value is 66.6, 02 9A means the current turbidity value is 66.6 NTU 949 949 950 950 951 -= 6. DR-C LWater CLProbe =951 += 6. DR-ECK Water EC Probe = 952 952 953 953 == 6.1 Specification: == 954 954 955 + 955 955 * **Power Input**: DC7~~30 956 956 957 957 * **Power Consumption** : 0.19W ... ... @@ -973,62 +973,17 @@ 973 973 974 974 * **Max Pressure**: 0.6MPa 975 975 976 -== 6.2 Wiring ==977 +== 2.2 Wiring == 977 977 978 978 [[image:image-20240720172548-2.png||height="348" width="571"]] 979 979 980 -== 6.3 Mechinical Drawing ==981 +== 2.3 Mechinical Drawing == 981 981 982 982 [[image:1752573238705-910.png||height="694" width="278"]] 983 983 984 -== 6.4 Installation == 985 985 986 -Flow-through installation: Use the matching flow slot for installation. The device and the flow slot are installed tightly. 987 987 988 -The measuring end is completely immersed in the measured liquid to ensure a steady flow rate without bubbles. 989 989 990 -It is recommended that the flow rate be controlled at 30-60Lh to ensure the accuracy of the test. 991 - 992 -[[image:1752573643879-991.png||height="360" width="343"]] 993 - 994 -== 6.5 Maintenance == 995 - 996 -* The device itself generally does not require daily maintenance. When an obvious fault occurs, please do not open it and repair it yourself, and contact us as soon as possible! 997 -* After using the electrode, please clean the electrode head with clean water and cover it with a protective cover. 998 -* When measuring the device, the measured liquid should flow and the flow rate should be uniform, and there should be no bubbles attached to the measuring end of the device. 999 -* If the electrode diaphragm is attached with dirt and mineral components, the sensitivity will be reduced, and it may not be possible to perform sufficient measurement. Please ensure that the platinum ring is clean. 1000 -* The platinum induction ring of a good residual chlorine electrode should always be kept clean and bright. If the platinum ring of the electrode becomes rough or covered with pollutants after measurement, please clean it according to the following method: (For reference) Inorganic pollution: immerse the electrode in 0.1mol/L dilute hydrochloric acid for 15 minutes, gently wipe the platinum ring of the residual chlorine electrode with a cotton swab, and then wash it with tap water. 1001 -* Organic or oil pollution: immerse the electrode in tap water with a small amount of detergent, such as dishwashing liquid, and thoroughly clean the sensing surface of the electrode sensor. Gently wipe the platinum ring of the electrode with a cotton swab, then rinse with tap water, and the cleaning is complete. If the platinum ring of the electrode has formed an oxide film, please use toothpaste or 1000-grit fine sandpaper to properly polish the sensing surface, and then clean it with tap water. The platinum ring is connected to the glass, so please handle it carefully when polishing. 1002 -The electrode has a service life of about one year, and a new electrode should be replaced in time after aging. 1003 -* Before the cable plug and the device plug are locked, do not put the plug part into water. 1004 - 1005 - 1006 - 1007 -== 6.6 RS485 Commands == 1008 - 1009 -RS485 signal 1010 -Standard Modbus-RTU protocol, baud rate: 9600; check bit: none; data bit: 8; stop bit: 1 1011 - 1012 - 1013 -== 6.7 Query address == 1014 - 1015 - 1016 - 1017 - 1018 - 1019 - 1020 - 1021 - 1022 - 1023 - 1024 - 1025 - 1026 - 1027 - 1028 - 1029 - 1030 - 1031 - 1032 1032 = 7. Water Quality Sensor Datasheet = 1033 1033 1034 1034 * **[[Water Quality Sensor Transmitter Datasheet>>https://www.dropbox.com/scl/fi/9tofocmgapkbddshznumn/Datasheet_WQS-xB-WQS-xS_Water-Quality-Sensor-Transmitter.pdf?rlkey=wxua12ur9swk30rkqnh2boo9z&st=axga6epf&dl=0]]**