Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 6 added, 0 removed)
  • image-20240718190121-1.png
  • image-20240718190204-2.png
  • image-20240718190221-3.png
  • image-20240718190249-4.png
  • image-20240718191336-5.png
  • image-20240718191348-6.png

Details

Page properties

Content

...	...	@@ -37,45 +37,48 @@
37	37	== 1.5 Installation ==
38	38
39	39
40		- Do not power on while connect the cables. Double check the wiring before power on.
	40	+**Electrode installation form**
41	41
42		-Installation Photo as reference:
	42	+A:Side wall installation
43	43
44		-**~ Submerged installation:**
	44	+B:Top flange installation
45	45
46		-The lead wire of the equipment passes through the waterproof pipe, and the 3/4 thread on the top of the equipment is connected to the 3/4 thread of the waterproof pipe with raw tape. Ensure that the top of the equipment and the equipment wire are not flooded.
	46	+C:Pipeline bend installation
47	47
48		-[[image:image-20240715181933-4.png||height="281" width="258"]]
	48	+D:Pipeline bend installation
49	49
50		-**~ Pipeline installation:**
	50	+E:Flow-through installation
51	51
52		-Connect the equipment to the pipeline through the 3/4 thread.
	52	+F:Submerged installation
53	53
54		-[[image:image-20240715182122-6.png||height="291" width="408"]]
	54	+[[image:image-20240718190121-1.png||height="350" width="520"]]
55	55
56		-**Sampling:**
	56	+**Several common installation methods of electrodes**
57	57
58		-Take representative water samples according to sampling requirements. If it is inconvenient to take samples, you can also put the electrode into the solution to be tested and read the output data. After a period of time, take out the electrode and clean it.
	58	+When installing the sensor on site, you should strictly follow the correct installation method shown in the following picture. Incorrect installation method will cause data deviation.
59	59
60		-**Measure the pH of the water sample:**
	60	+A. Several common incorrect installation methods
61	61
62		-First rinse the electrode with distilled water, then rinse it with the water sample, then immerse the electrode in the sample, carefully shake the test cup or stir it to accelerate the electrode balance, let it stand, and record the pH value when the reading is stable.
	62	+[[image:image-20240718190204-2.png||height="262" width="487"]]
63	63
	64	+Error cause: The electrode joint is too long, the extension part is too short, the sensor is easy to form a dead cavity, resulting in measurement error.
64	64
	66	+[[image:image-20240718190221-3.png||height="292" width="500"]]
	67	+
	68	+Error cause: Measurement error or instability may occur due to water flow not being able to fill the pipe or air accumulation at high altitudes.
	69	+
	70	+B. Correct installation method
	71	+
	72	+[[image:image-20240718190249-4.png||height="287" width="515"]]
	73	+
	74	+
65	65	== 1.6 Maintain ==
66	66
67	67
68		-* The equipment itself generally does not require daily maintenance. When an obvious fault occurs, please do not open it and repair it yourself. Contact us as soon as possible!
69		-* There is an appropriate amount of soaking solution in the protective bottle at the front end of the electrode. The electrode head is soaked in it to keep the glass bulb and the liquid junction activated. When measuring, loosen the bottle cap, pull out the electrode, and rinse it with pure water before use.
70		-* Preparation of electrode soaking solution: Take a packet of PH4.00 buffer, dissolve it in 250 ml of pure water, and soak it in 3M potassium chloride solution. The preparation is as follows: Take 25 grams of analytical pure potassium chloride and dissolve it in 100 ml of pure water.
71		-* The glass bulb at the front end of the electrode cannot come into contact with hard objects. Any damage and scratches will make the electrode ineffective.
72		-* Before measurement, the bubbles in the electrode glass bulb should be shaken off, otherwise it will affect the measurement. When measuring, the electrode should be stirred in the measured solution and then placed still to accelerate the response.
73		-* The electrode should be cleaned with deionized water before and after measurement to ensure accuracy.
74		-* After long-term use, the pH electrode will become passivated, which is characterized by a decrease in sensitivity gradient, slow response, and inaccurate readings. At this time, the bulb at the bottom of the electrode can be soaked in 0.1M dilute hydrochloric acid for 24 hours (0.1M dilute hydrochloric acid preparation: 9 ml of hydrochloric acid is diluted to 1000 ml with distilled water), and then soaked in 3.3M potassium chloride solution for 24 hours. If the pH electrode is seriously passivated and soaking in 0.1M hydrochloric acid has no effect, the pH electrode bulb can be soaked in 4% HF (hydrofluoric acid) for 3-5 seconds, washed with pure water, and then soaked in 3.3M potassium chloride solution for 24 hours to restore its performance.
75		-* Glass bulb contamination or liquid junction blockage can also cause electrode passivation. At this time, it should be cleaned with an appropriate solution according to the nature of the contaminant.
76		-* (((
77		-The equipment should be calibrated before each use. For long-term use, it is recommended to calibrate once every 3 months. The calibration frequency should be adjusted appropriately according to different application conditions (degree of dirt in the application, deposition of chemical substances, etc.). After aging, the electrodes should be replaced in time.
78		-)))
	78	+* The equipment itself generally does not require daily maintenance. When an obvious fault occurs, please do not open it and repair it yourself, and contact us as soon as possible.
	79	+* If the electrode is not used for a long time, it can generally be stored in a dry place, but it must be placed (stored) in distilled water for several hours before use to activate the electrode. Electrodes that are frequently used can be placed (stored) in distilled water.
	80	+* Cleaning of conductivity electrodes: Organic stains on the electrode can be cleaned with warm water containing detergent, or with alcohol. Calcium and magnesium precipitates are best cleaned with 10% citric acid. The electrode plate or pole can only be cleaned by chemical methods or by shaking in water. Wiping the electrode plate will damage the coating (platinum black) on the electrode surface.
	81	+* The equipment should be calibrated before each use. It is recommended to calibrate it every 3 months for long-term use. The calibration frequency should be adjusted appropriately according to different application conditions (degree of dirt in the application, deposition of chemical substances, etc.).
79	79
80	80	== 1.7 RS485 Commands ==
81	81
...	...	@@ -99,7 +99,7 @@
99	99
100	100	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:561.333px" %)
101	101	|=(% style="width: 50px;background-color:#4F81BD;color:white" %)New address|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Function code|=(% style="width: 106px; background-color: rgb(79, 129, 189); color: white;" %)Data length|=(% style="width: 93px; background-color: rgb(79, 129, 189); color: white;" %)CRC16 low|=(% style="width: 104px; background-color: rgb(79, 129, 189); color: white;" %)CRC16 high
102		-|(% style="width:99px" %)0X1|(% style="width:112px" %)0X3|(% style="width:106px" %)0X00|(% style="width:93px" %)0X20|(% style="width:104px" %)0XF0
	105	+|(% style="width:99px" %)0X01|(% style="width:112px" %)0X03|(% style="width:106px" %)0X00|(% style="width:93px" %)0X20|(% style="width:104px" %)0XF0
103	103
104	104	=== 1.7.2 Change address ===
105	105
...	...	@@ -120,8 +120,8 @@
120	120
121	121	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:676.25px" %)
122	122	|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Function code|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address high|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Quantity high|=(% style="width: 1px; background-color: rgb(79, 129, 189); color: white;" %)Quantity low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)CRC16 low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)CRC16 high
123		-|(% style="width:99px" %)0X01|(% style="width:112px" %)0X06|(% style="width:135px" %)0X00|(% style="width:126px" %)0X23|(% style="width:85px" %)0X00|(% style="width:1px" %)0X01|(% style="width:1px" %)0XFA|(% style="width:1px" %)(((
124		-0X97
	126	+|(% style="width:99px" %)0X01|(% style="width:112px" %)0X06|(% style="width:135px" %)0X00|(% style="width:126px" %)0X23|(% style="width:85px" %)0X00|(% style="width:1px" %)0X01|(% style="width:1px" %)0XF8|(% style="width:1px" %)(((
	127	+0X07
125	125	)))
126	126
127	127	Change the intercept of the sensor with address 1 to 10 (default 0), which is 0X000A in the command.
...	...	@@ -132,14 +132,13 @@
132	132	|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Function code|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address high|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Quantity high|=(% style="width: 1px; background-color: rgb(79, 129, 189); color: white;" %)Quantity low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)CRC16 low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)CRC16 high
133	133	|(% style="width:99px" %)0X01|(% style="width:112px" %)0X06|(% style="width:135px" %)(((
134	134	0X02
135		-)))|(% style="width:126px" %)0X00|(% style="width:85px" %)0X00|(% style="width:1px" %)0X0A|(% style="width:1px" %)0X0A|(% style="width:1px" %)(((
136		-0XE5
	138	+)))|(% style="width:126px" %)0X00|(% style="width:85px" %)0X00|(% style="width:1px" %)0X0A|(% style="width:1px" %)0X38|(% style="width:1px" %)(((
	139	+0X8F
137	137	)))
138	138
139		-
140	140	=== 1.7.4 Query data ===
141	141
142		-The address of the EC K10 sensor is
	144	+The address of the EC K10 sensor is 11
143	143
144	144	The query data command is 11 03 00 00 00 02 C6 9B
145	145
...	...	@@ -203,15 +203,131 @@
203	203	|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Function code|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address high|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Quantity high|=(% style="width: 1px; background-color: rgb(79, 129, 189); color: white;" %)Quantity low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)CRC16 low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)CRC16 high
204	204	|(% style="width:99px" %)0X11|(% style="width:112px" %)0X06|(% style="width:135px" %)0X00|(% style="width:126px" %)0X26|(% style="width:85px" %)0X00|(% style="width:1px" %)0X02|(% style="width:1px" %)0XEB|(% style="width:1px" %)0X50
205	205
	208	+= 2. DR-PH01 Water PH Sensor =
206	206
207	207
	211	+== 2.1 Specification:[[Edit>>url:http://wiki.dragino.com/xwiki/bin/edit/Main/Water%20Quality%20Sensors/WebHome?section=2]] ==
208	208
	213	+* **Power Input**: DC7~~30
	214	+* **Power Consumption** : < 0.5W
	215	+* **Interface**: RS485. 9600 Baud Rate
	216	+* **pH measurement range**: 0~~14.00pH; resolution: 0.01pH
	217	+* **pH measurement error**:±0.15pH
	218	+* **Repeatability error**:±0.02pH
	219	+* **Temperature measurement range**:0~~60℃; resolution: 0.1℃ (set temperature for manual temperature compensation, default 25℃)
	220	+* **Temperature measurement error**: ±0.5℃
	221	+* **Temperature Measure Range**: -20 ~~ 60 °C
	222	+* **Temperature Accuracy: **±0.5 °C
	223	+* **IP Rated**: IP68
	224	+* **Max Pressure**: 0.6MPa
209	209
210		-= 2. DR-PH01 Water PH Sensor =
	226	+== 2.2 Wiring ==
211	211
212		-== 2.7 RS485 Commands ==
213	213
	229	+== (% style="color:inherit; font-family:inherit" %)2.3 (% style="color:inherit; font-family:inherit; font-size:26px" %)Mechinical Drawing(%%) ==
214	214
	231	+[[image:image-20240714174241-2.png]]
	232	+
	233	+
	234	+== 2.4 Installation Notice ==
	235	+
	236	+Do not power on while connect the cables. Double check the wiring before power on.
	237	+
	238	+Installation Photo as reference:
	239	+
	240	+**~ Submerged installation:**
	241	+
	242	+The lead wire of the equipment passes through the waterproof pipe, and the 3/4 thread on the top of the equipment is connected to the 3/4 thread of the waterproof pipe with raw tape. Ensure that the top of the equipment and the equipment wire are not flooded.
	243	+
	244	+[[image:image-20240718191348-6.png]]
	245	+
	246	+**~ Pipeline installation:**
	247	+
	248	+Connect the equipment to the pipeline through the 3/4 thread.
	249	+
	250	+[[image:image-20240718191336-5.png||height="239" width="326"]]
	251	+
	252	+**Sampling:**
	253	+
	254	+Take representative water samples according to sampling requirements. If it is inconvenient to take samples, you can also put the electrode into the solution to be tested and read the output data. After a period of time, take out the electrode and clean it.
	255	+
	256	+**Measure the pH of the water sample:**
	257	+
	258	+First rinse the electrode with distilled water, then rinse it with the water sample, then immerse the electrode in the sample, carefully shake the test cup or stir it to accelerate the electrode balance, let it stand, and record the pH value when the reading is stable.
	259	+
	260	+
	261	+=== 2.5 Maintenance ===
	262	+
	263	+
	264	+* The equipment itself generally does not require daily maintenance. When an obvious fault occurs, please do not open it and repair it yourself. Contact us as soon as possible!
	265	+* There is an appropriate amount of soaking solution in the protective bottle at the front end of the electrode. The electrode head is soaked in it to keep the glass bulb and the liquid junction activated. When measuring, loosen the bottle cap, pull out the electrode, and rinse it with pure water before use.
	266	+* Preparation of electrode soaking solution: Take a packet of PH4.00 buffer, dissolve it in 250 ml of pure water, and soak it in 3M potassium chloride solution. The preparation is as follows: Take 25 grams of analytical pure potassium chloride and dissolve it in 100 ml of pure water.
	267	+* The glass bulb at the front end of the electrode cannot come into contact with hard objects. Any damage and scratches will make the electrode ineffective.
	268	+* Before measurement, the bubbles in the electrode glass bulb should be shaken off, otherwise it will affect the measurement. When measuring, the electrode should be stirred in the measured solution and then placed still to accelerate the response.
	269	+* The electrode should be cleaned with deionized water before and after measurement to ensure accuracy.
	270	+* After long-term use, the pH electrode will become passivated, which is characterized by a decrease in sensitivity gradient, slow response, and inaccurate readings. At this time, the bulb at the bottom of the electrode can be soaked in 0.1M dilute hydrochloric acid for 24 hours (0.1M dilute hydrochloric acid preparation: 9 ml of hydrochloric acid is diluted to 1000 ml with distilled water), and then soaked in 3.3M potassium chloride solution for 24 hours. If the pH electrode is seriously passivated and soaking in 0.1M hydrochloric acid has no effect, the pH electrode bulb can be soaked in 4% HF (hydrofluoric acid) for 3-5 seconds, washed with pure water, and then soaked in 3.3M potassium chloride solution for 24 hours to restore its performance.
	271	+* Glass bulb contamination or liquid junction blockage can also cause electrode passivation. At this time, it should be cleaned with an appropriate solution according to the nature of the contaminant.
	272	+* (((
	273	+The equipment should be calibrated before each use. For long-term use, it is recommended to calibrate once every 3 months. The calibration frequency should be adjusted appropriately according to different application conditions (degree of dirt in the application, deposition of chemical substances, etc.). After aging, the electrodes should be replaced in time.
	274	+)))
	275	+
	276	+== 2.6 RS485 Commands ==
	277	+
	278	+RS485 signaldefault address 0x10
	279	+Standard Modbus-RTU protocol, baud rate: 9600; check bit: none; data bit: 8; stop bit: 1
	280	+
	281	+=== 2.6.1 Query data ===
	282	+
	283	+send
	284	+
	285	+(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:676.25px" %)
	286	+|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Original address|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Function code|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address high|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Quantity high|=(% style="width: 1px; background-color: rgb(79, 129, 189); color: white;" %)Quantity low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)CRC16 low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)CRC16 high
	287	+|(% style="width:99px" %)0XFE |(% style="width:112px" %)0X03|(% style="width:135px" %)0X00|(% style="width:126px" %)0X50|(% style="width:85px" %)0X00|(% style="width:1px" %)0X00|(% style="width:1px" %)0X51|(% style="width:1px" %)0XD4
	288	+
	289	+response
	290	+
	291	+(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:561.333px" %)
	292	+|=(% style="width: 50px;background-color:#4F81BD;color:white" %)New address|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Function code|=(% style="width: 106px; background-color: rgb(79, 129, 189); color: white;" %)Data length|=(% style="width: 93px; background-color: rgb(79, 129, 189); color: white;" %)CRC16 low|=(% style="width: 104px; background-color: rgb(79, 129, 189); color: white;" %)CRC16 high
	293	+|(% style="width:99px" %)0X01|(% style="width:112px" %)0X03|(% style="width:106px" %)0X00|(% style="width:93px" %)0X20|(% style="width:104px" %)0XF0
	294	+
	295	+=== 2.6.2 Change address ===
	296	+
	297	+For example: Change the address of the sensor with address 1 to 2, master → slave
	298	+
	299	+(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:676.25px" %)
	300	+|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Original address|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Function code|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address high|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Quantity high|=(% style="width: 1px; background-color: rgb(79, 129, 189); color: white;" %)Quantity low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)CRC16 low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)CRC16 high
	301	+|(% style="width:99px" %)0X01|(% style="width:112px" %)0X06|(% style="width:135px" %)0X00|(% style="width:126px" %)0X50|(% style="width:85px" %)0X00|(% style="width:1px" %)0X02|(% style="width:1px" %)0X08|(% style="width:1px" %)0X1A
	302	+
	303	+If the sensor receives correctly, the data is returned along the original path.
	304	+Note: If you forget the original address of the sensor, you can use the broadcast address 0XFE instead. When using 0XFE, the host can only connect to one slave, and the return address is still the original address, which can be used as a method of address query.
	305	+
	306	+
	307	+=== 2.6.3 Modify intercept ===
	308	+
	309	+
	310	+send
	311	+
	312	+(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:676.25px" %)
	313	+|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Function code|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address high|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Quantity high|=(% style="width: 1px; background-color: rgb(79, 129, 189); color: white;" %)Quantity low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)CRC16 low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)CRC16 high
	314	+|(% style="width:99px" %)0X10|(% style="width:112px" %)0X06|(% style="width:135px" %)0X00|(% style="width:126px" %)0X10|(% style="width:85px" %)0X00|(% style="width:1px" %)0X64|(% style="width:1px" %)0X8A|(% style="width:1px" %)(((
	315	+0XA5
	316	+)))
	317	+
	318	+Change the intercept of the sensor with address 1 to 10 (default 0), which is 0X000A in the command.
	319	+
	320	+response
	321	+
	322	+(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:676.25px" %)
	323	+|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Function code|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address high|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Address low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)Quantity high|=(% style="width: 1px; background-color: rgb(79, 129, 189); color: white;" %)Quantity low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)CRC16 low|=(% style="width: 50px;background-color:#4F81BD;color:white" %)CRC16 high
	324	+|(% style="width:99px" %)0X10|(% style="width:112px" %)0X06|(% style="width:135px" %)(((
	325	+0X00
	326	+)))|(% style="width:126px" %)0X10|(% style="width:85px" %)0X00|(% style="width:1px" %)0X64|(% style="width:1px" %)0X8A|(% style="width:1px" %)(((
	327	+0XA5
	328	+)))
	329	+
	330	+=== 2.6.4 Query data ===
	331	+
	332	+
215	215	The address of the pH  sensor is 10
216	216
217	217	The query data command is 10 03 00 00 00 01 87 4B. After the query, 7 bytes will be returned.
...	...	@@ -221,8 +221,85 @@
221	221	02 AE is the pH value, which is converted into decimal to get 686, and then two decimal places are added to get the actual value. 02 AE means the current pH value is 6.86.
222	222
223	223
	342	+=== 2.6.5 Calibration Method ===
	343	+
	344	+
	345	+This device uses three-point calibration, and three known pH standard solutions need to be prepared.
	346	+The calibration steps are as follows:
	347	+(1) Place the electrode in distilled water to clean it, and then place it in 9.18 standard buffer solution. After the data stabilizes, enter the following calibration command, and the 9.18 calibration is completed.
	348	+
	349	+(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:575.333px" %)
	350	+|=(% style="width: 64px; background-color: rgb(79, 129, 189); color: white;" %)Address|=(% style="width: 72px; background-color: rgb(79, 129, 189); color: white;" %)Function code|=(% style="width: 66px; background-color: rgb(79, 129, 189); color: white;" %)Address high|=(% style="width: 68px; background-color: rgb(79, 129, 189); color: white;" %)Address low|=(% style="width: 72px; background-color: rgb(79, 129, 189); color: white;" %)Quantity high|=(% style="width: 70px; background-color: rgb(79, 129, 189); color: white;" %)Quantity low|=(% style="width: 55px; background-color: rgb(79, 129, 189); color: white;" %)CRC16 low|=(% style="width: 55px; background-color: rgb(79, 129, 189); color: white;" %)CRC16 high
	351	+|(% style="width:64px" %)0X10|(% style="width:72px" %)0X06|(% style="width:66px" %)(((
	352	+0X00
	353	+)))|(% style="width:68px" %)0X20|(% style="width:72px" %)0XFF|(% style="width:70px" %)0XFF|(% style="width:55px" %)0X8A|(% style="width:55px" %)(((
	354	+0XF1
	355	+)))
	356	+
	357	+(2) Wash the electrode in distilled water and place it in 6.86 standard buffer. After the data stabilizes, enter the following calibration command. The 6.86 calibration is completed.
	358	+
	359	+(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:575.333px" %)
	360	+|=(% style="width: 64px; background-color: rgb(79, 129, 189); color: white;" %)Address|=(% style="width: 72px; background-color: rgb(79, 129, 189); color: white;" %)Function code|=(% style="width: 66px; background-color: rgb(79, 129, 189); color: white;" %)Address high|=(% style="width: 68px; background-color: rgb(79, 129, 189); color: white;" %)Address low|=(% style="width: 72px; background-color: rgb(79, 129, 189); color: white;" %)Quantity high|=(% style="width: 70px; background-color: rgb(79, 129, 189); color: white;" %)Quantity low|=(% style="width: 55px; background-color: rgb(79, 129, 189); color: white;" %)CRC16 low|=(% style="width: 55px; background-color: rgb(79, 129, 189); color: white;" %)CRC16 high
	361	+|(% style="width:64px" %)0X10|(% style="width:72px" %)0X06|(% style="width:66px" %)(((
	362	+0X00
	363	+)))|(% style="width:68px" %)0X21|(% style="width:72px" %)0XFF|(% style="width:70px" %)0XFF|(% style="width:55px" %)0XDB|(% style="width:55px" %)(((
	364	+0X31
	365	+)))
	366	+
	367	+(3) Wash the electrode in distilled water and place it in 4.01 standard buffer. After the data stabilizes, enter the following calibration command, and the 4.00 calibration is completed.
	368	+
	369	+(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:575.333px" %)
	370	+|=(% style="width: 64px; background-color: rgb(79, 129, 189); color: white;" %)Address|=(% style="width: 72px; background-color: rgb(79, 129, 189); color: white;" %)Function code|=(% style="width: 66px; background-color: rgb(79, 129, 189); color: white;" %)Address high|=(% style="width: 68px; background-color: rgb(79, 129, 189); color: white;" %)Address low|=(% style="width: 72px; background-color: rgb(79, 129, 189); color: white;" %)Quantity high|=(% style="width: 70px; background-color: rgb(79, 129, 189); color: white;" %)Quantity low|=(% style="width: 55px; background-color: rgb(79, 129, 189); color: white;" %)CRC16 low|=(% style="width: 55px; background-color: rgb(79, 129, 189); color: white;" %)CRC16 high
	371	+|(% style="width:64px" %)0X10|(% style="width:72px" %)0X06|(% style="width:66px" %)(((
	372	+0X00
	373	+)))|(% style="width:68px" %)0X22|(% style="width:72px" %)0XFF|(% style="width:70px" %)0XFF|(% style="width:55px" %)0X2B|(% style="width:55px" %)(((
	374	+0X31
	375	+)))
	376	+
	377	+After the above three steps are completed, the calibration is successful. The advantage of three-point calibration compared to two-point calibration is that the electrode is calibrated separately in the acid and alkali parts, thereby achieving accurate calibration of the full range and making the measurement data more accurate.
	378	+
	379	+
224	224	= 3. DR-ORP1 Water ORP Sensor =
225	225
	382	+
	383	+
	384	+== 3.1 Specification:[[Edit>>url:http://wiki.dragino.com/xwiki/bin/edit/Main/Water%20Quality%20Sensors/WebHome?section=2]] ==
	385	+
	386	+* **Power Input**: DC7~~30
	387	+* **Power Consumption** : < 0.5W
	388	+* **Interface**: RS485. 9600 Baud Rate
	389	+* **Measurement error**: ±3mV
	390	+* **Stability**: ≤2mv/24 hours
	391	+* **Equipment working conditions**: Ambient temperature: 0-60℃ Relative humidity: <85%RH
	392	+* **IP Rated**: IP68
	393	+* **Max Pressure**: 0.6MPa
	394	+
	395	+== 3.2 Wiring ==
	396	+
	397	+
	398	+== 3.3 Mechinical Drawing ==
	399	+
	400	+[[image:image-20240714174241-2.png]]
	401	+
	402	+== 3.4 Installation Notice ==
	403	+
	404	+Do not power on while connect the cables. Double check the wiring before power on.
	405	+
	406	+Installation Photo as reference:
	407	+
	408	+**~ Submerged installation:**
	409	+
	410	+The lead wire of the equipment passes through the waterproof pipe, and the 3/4 thread on the top of the equipment is connected to the 3/4 thread of the waterproof pipe with raw tape. Ensure that the top of the equipment and the equipment wire are not flooded.
	411	+
	412	+[[image:image-20240718191348-6.png]]
	413	+
	414	+**~ Pipeline installation:**
	415	+
	416	+Connect the equipment to the pipeline through the 3/4 thread.
	417	+
	418	+[[image:image-20240718191336-5.png||height="239" width="326"]]
	419	+
	420	+
226	226	== 3.7 RS485 Commands ==
227	227
228	228
...	...	@@ -261,5 +261,3 @@
261	261	For example, the returned data is 15 03 02 (% style="color:red" %)**02 9A**(%%) 09 4C
262	262
263	263	02 9A is the turbidity value, converted to decimal, it is 666, and then divided by 10, the actual value is 66.6, 02 9A means the current turbidity value is 66.6 NTU
264		-
265		-

image-20240718190121-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.karry

Size

...	...	@@ -1,0 +1,1 @@
	1	+281.1 KB

Content

image-20240718190204-2.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.karry

Size

...	...	@@ -1,0 +1,1 @@
	1	+111.8 KB

Content

image-20240718190221-3.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.karry

Size

...	...	@@ -1,0 +1,1 @@
	1	+140.2 KB

Content

image-20240718190249-4.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.karry

Size

...	...	@@ -1,0 +1,1 @@
	1	+111.6 KB

Content

image-20240718191336-5.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.karry

Size

...	...	@@ -1,0 +1,1 @@
	1	+46.6 KB

Content

image-20240718191348-6.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.karry

Size

...	...	@@ -1,0 +1,1 @@
	1	+91.2 KB

Content