WSC2-L -- Weather Station Kit User Manual

The Dragino WSC2-L is the main unit in Dragino Weather Station solution which desianed for (% style="color:blue" %)**measuring atmospheric conditions**(%%) to provide information for weatherforecasts and to study the weather and climate.

30

31

WSC2-L can reads values from various sensors and upload these sensor data to IoT server via LoRaWAN wireless protocol.

32

33

WSC2-L supports input and (% style="color:blue" %)**12V recharge power**(%%) and (% style="color:blue" %)**build in 1000mAh rechargeable Li-ion battery**(%%). lf the user needs to connect other sensors, please kindly note the (% style="color:blue" %)**externalpower supply is required**.

34

35

WSC2-L supports connecting 3rd party RS485 multiple sensors. Users can purchase DR-F6C-4M one-to-four cables to connect more sensors according to their needs.

36

37

38

== 1.2 Features & Spec for WSC2-L Transmitter ==

39

40

41

* LoRaWAN 1.0.3 Class A

42

* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865

43

* Ultra-low power consumption

44

* Support reading the Rain Gauge, Wind Speed/Direction, CO2/PM2.5/PM10, Rain/Snow Detect, Temperature, Humidiity, Iillumiance, Pressure, Total Solar Radiation, PAR

45

* Support WSS09 9 in 1 Sensors: Wind Speed, Wind Direction, Temperature, Humidity, Air Pressure, Illumination, PM2.5, PM10, Noise & Rain Gauge

46

* RS485 Interface for 3rd party Sensors

47

* Support WSS08 optical Rain Gauge or tipping bucket Rain Gauge

48

* Support Bluetooth v5.1 and LoRaWAN remote configure

49

* Support wireless OTA update firmware

50

* AT Commands to change parameters

51

* Downlink to change configure

52

* IP66 Waterproof Enclosure

53

* 1000mAh Rechargeable Li-ion Battery

54

* Input and Recharge power: 12v

55

56

== 1.3 Specification for WSS-09 9 in 1 weather sensors ==

57

58

**~ Older versions of interfaces** **New version of the interface**

59

60

[[image:image-20240708092247-1.png||height="264" width="240"]] [[image:image-20250505190455-1.png||height="283" width="226"]]

61

62

More Detail: [[WSS-09 Manual.>>doc:Main.Agriculture & Weather Stations.WebHome||anchor="H1.WSS099in1WeatherStationSensor"]]

63

64

65

(% style="color:blue" %)**Wind Speed:**

66

67

* Range: 0~~60m/s

68

* Accuracy: ±(0.2m/s±0.02*v)(v : the wind speed)

69

* Ultrasonic measurement,no start wind strength needed

70

71

(% style="color:blue" %)**Wind Direction:**

* Range: 0~~3599

* Accuracy: ±3°

* Ultrasonic measurement,no start wind strength needed

76

* Built-in electronic compass. No need to consider installation direction

77

78

(% style="color:blue" %)**Temperature:**

79

80

* Range: -40°C ~~ +80°C

81

* Accuracy: ±0.5°C

82

83

(% style="color:blue" %)**Humidity:**

84

85

* Range: 0 ~~ 99% RH

86

* Accuracy Tolerance : Typ ±3% RH

87

88

(% style="color:blue" %)**Air Pressure:**

89

90

* Accuracy: ±0.15kPa@25°C 101kPa

91

* Range: 0~~120kPa

92

93

(% style="color:blue" %)**Noise:**

* Range: 30dB~~120dB

* Accuracy: ±0.5dB

(% style="color:blue" %)**PM2.5:**

99

100

* Range: 0~~1000ug/m3

* Accuracy: ±3%FS

* Resolution: 1ug/m3

(% style="color:blue" %)**PM10:**

105

106

* Range: 0~~1000ug/m3

* Accuracy: ±3%FS

* Resolution: 1ug/m3

(% style="color:blue" %)**llumination:**

111

112

* Range: 0~~200k Lux

113

* Accuracy: ±7%(25 °C)

114

115

== 1.4 Specification for WSS-08 Optical Rain Guage ==

116

117

**Older versions of interfaces** **New version of the interface**

118

119

[[image:image-20240707215336-2.png||height="147" width="201"]] [[image:image-20250505190636-2.png||height="158" width="201"]]

120

121

* Input Power: 9~~30 VDC

122

* Sense diameter: 6cm

123

* Pulse Output

124

125

More Detail: [[WSS-08 Manual.>>doc:Main.Agriculture & Weather Stations.WebHome||anchor="H2.WSS08OpticalRangeGuage"]]

= 2. How to use =

== 2.1 Installation ==

130

131

132

Below is an installation example for the weather station:

133

134

[[image:image-20240327231510-1.png||height="499" width="1156"]]

135

136

137

(% style="color:blue" %)** Wiring:**

138

139

1. WSC2-L and sensors all powered by solar power via MPPT

140

1. WSC2-L Weather Station Kit already include 9 sensors.

141

1. Possible to add optional 3rd sensors to measure more parameter

142

143

(% style="color:red" %)**Notice 1:**

144

145

* All weather sensors and WSC2-L are powered by MPPT solar recharge controller. MPPT is connected to solar panel and storage battery.

146

* Weather sensors won't work if solar panel and storage battery fails.

147

148

(% style="color:red" %)**Notice 2:**

149

150

Due to shipment and importation limitation, user is better to purchase below parts locally:

* Solar Panel

* Storage Battery

* MPPT Solar Recharger

155

* Cabinet.

156

157

== 2.2 How it works? ==

(((

Each WSC2-L is shipped with a worldwide unique set of OTAA keys. To use WSC2-L in a LoRaWAN network, user needs to input the OTAA keys in LoRaWAN network server. After finish installation as above. Create WSC2-L in your LoRaWAN server and Power on WSC2-L , it can join the LoRaWAN network and start to transmit sensor data. The default period for each uplink is 20 minutes.

)))

== 2.3 Example to use for LoRaWAN network ==

166

167

168

This section shows an example for how to join the TTN V3 LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.

169

170

Assume the DLOS8 is already set to connect to [[TTN V3 network >>url:https://eu1.cloud.thethings.network/]]. We need to add the WSC2-L device in TTN V3:

171

172

173

(% style="color:blue" %)**Step 1**(%%): Create a device in TTN V3 with the OTAA keys from WSC2-L.

174

175

Each WSC2-L is shipped with a sticker with the default device EUI as below:

176

177

[[image:image-20230426084533-1.png||height="231" width="497"]]

178

179

180

User can enter these keys in the LoRaWAN Server portal. Below is TTN V3 screen shot:

181

182

The user needs to press and hold the ACT button(Push button) for more than 3s to start the node.

183

184

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png||height="386" width="262"]]

185

186

187

**Create the application.**

188

189

[[image:image-20250530163301-2.jpeg]]

190

191

[[image:image-20250530163311-3.jpeg]]

192

193

194

**Add devices to the created Application.**

195

196

[[image:image-20250530163335-4.jpeg]]

197

198

[[image:image-20250530163350-5.jpeg]]

199

200

201

**Enter end device specifics manually.**

202

203

[[image:image-20250530163411-6.jpeg]]

204

205

206

**Add DevEUI and AppKey.**

207

208

**Customize a platform ID for the device.**

209

210

[[image:image-20250530163435-7.jpeg]]

211

212

213

(% style="color:blue" %)**Step 2**(%%): Add decoder.

214

215

In TTN, user can add a custom payload so it shows friendly reading.

216

217

Click this link to get the decoder: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/WSC2-LB>>https://github.com/dragino/dragino-end-node-decoder/tree/main/WSC2-LB]]

218

219

Below is TTN screen shot:

220

221

[[image:image-20250530163456-8.jpeg]]

222

223

[[image:image-20250530163514-9.jpeg]]

(((

(% style="color:blue" %)**Step 3**(%%): Power on WSC2-L, it will start to join TTN server. After join success, it will start to upload sensor data to TTN V3 and user can see in the panel.

228

)))

229

230

[[image:image-20250530163532-10.jpeg]]

231

232

233

== 2.4 Uplink Payload ==

234

235

236

Uplink payloads include two types: Valid Sensor Value and other status / control command.

237

238

* Valid Sensor Value: Use FPORT=2

239

* Other control command: Use FPORT other than 2.

240

241

=== 2.4.1 Uplink FPORT~=5, Device Status ===

242

243

244

Uplink the device configures with FPORT=5. Once WSC2-L Joined the network, it will uplink this message to the server.

245

246

(((

247

User can also use downlink command**(0x2601)** to ask WSC2-L to resend this uplink

248

)))

249

250

(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:500px" %)

251

|=(% style="width: 70px;background-color:#4F81BD;color:white" %)**Size(**bytes)|=(% style="width: 85px;background-color:#4F81BD;color:white" %)1|=(% style="width: 105px;background-color:#4F81BD;color:white" %)**2**|=(% style="width: 105px;background-color:#4F81BD;color:white" %)**1**|=(% style="width: 85px;background-color:#4F81BD;color:white" %)**1**|=(% style="width: 50px;background-color:#4F81BD;color:white" %)**2**

252

|(% style="width:99px" %)Value|(% style="width:112px" %)[[Sensor Model>>||anchor="HSensorModel:"]]|(% style="width:135px" %)[[Firmware Version>>||anchor="HFirmwareVersion:"]]|(% style="width:126px" %)[[Frequency Band>>||anchor="HFrequencyBand:"]]|(% style="width:85px" %)[[Sub-band>>||anchor="HSub-Band:"]]|(% style="width:46px" %)[[BAT>>||anchor="HBAT:"]]

253

254

[[image:image-20240415092848-2.png||height="329" width="1045"]]

255

256

257

Example Payload (FPort=5): [[image:image-20240415091027-1.png||height="16" width="104"]]

258

259

260

==== (% style="color:#037691" %)**Sensor Model:**(%%) ====

261

262

For WSC2-L, this value is 0x2E.

263

264

265

==== (% style="color:#037691" %)**Firmware Version:**(%%) ====

266

267

0x0100, Means: v1.0.0 version.

268

269

270

==== (% style="color:#037691" %)**Frequency Band:**(%%) ====

0x01: EU868

0x02: US915

0x03: IN865

0x04: AU915

0x05: KZ865

0x06: RU864

0x07: AS923

0x08: AS923-1

0x09: AS923-2

0x0a: AS923-3

==== (% style="color:#037691" %)**Sub-Band:**(%%) ====

294

295

value 0x00 ~~ 0x08(only for CN470, AU915,US915. Others are0x00)

296

297

298

==== (% style="color:#037691" %)**BAT:**(%%) ====

299

300

(((

301

shows the battery voltage for WSC2-L MCU.

)))

(((

Ex1: 0x0FE4/1000 = 4068/1000=4.068V

)))

Users can also use the downlink command (0x2301) to change the uplink port of WSC2-L:

310

311

(% style="color:#037691" %)**Example**(%%) (% style="color:#037691" %)**Downlink:0x23 01(Change to port 1)**

312

313

[[image:image-20240413104831-3.png||height="364" width="934"]]

314

315

316

=== 2.4.2 Uplink FPORT~=2, Real time sensor value ===

(((

WSC2-L will send this uplink after Device Config uplink once join LoRaWAN network successfully. And it will periodically send this uplink. Default interval is 20 minutes and [[can be changed>>||anchor="H3.1SetTransmitIntervalTime"]].

)))

(((

Uplink uses FPORT=2 and every 20 minutes send one uplink by default.

)))

(((

The upload length is dynamic, depends on what type of weather sensors are connected. The uplink payload is combined with sensor segments. As below:

)))

(% style="color:#4472c4" %)** Uplink Payload**:

334

335

(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:464px" %)

336

|(% style="width:140px" %)Sensor Segment 1|(% style="width:139px" %)Sensor Segment 2|(% style="width:42px" %)……|(% style="width:140px" %)Sensor Segment n

337

338

(% style="color:#4472c4" %)** Sensor Segment Define**:

339

340

(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:330px" %)

341

|(% style="width:89px" %)Type Code|(% style="width:114px" %)Length (Bytes)|(% style="width:124px" %)Measured Value

342

343

(% style="color:#4472c4" %)**Sensor Type Table:**

344

345

(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:515px" %)

346

|(% style="background-color:#4f81bd; color:white; width:80px" %)**Sensor Type**|(% style="background-color:#4f81bd; color:white; width:65px" %)**Type Code**|(% style="background-color:#4f81bd; color:white; width:116px" %)**Range**|(% style="background-color:#4f81bd; color:white; width:88px" %)**Length( Bytes)**|(% style="background-color:#4f81bd; color:white; width:166px" %)**Example**

347

|(% style="width:103px" %)Wind Speed|(% style="width:91px" %)0x01|(% style="width:116px" %)(((

348

Speed: 0 ~~ 60m/s

349

)))|(% style="width:88px" %)0x02 |(% style="width:181px" %)(((

0x0028/100=0.40m/s

)))

|(% style="width:103px" %)(((

354

Wind Direction

355

)))|(% style="width:91px" %)0x03|(% style="width:116px" %)Direction: 0~~7|(% style="width:88px" %)0x02|(% style="width:181px" %)(((

356

0X0004=3(Due north is 0, increasing clockwise, and due east is 2)

357

)))

358

|(% style="width:103px" %)Wind Angle|(% style="width:91px" %)0x04|(% style="width:116px" %)(((

359

Angel: 0 ~~ 359°

360

)))|(% style="width:88px" %)0x02|(% style="width:181px" %)(((

361

0x02C9/10=66.6°(Due north is 0°, increasing clockwise, due east is 90°)

)))

0xFFDD/10=-3.5°C

)))

0x023e/10=57.4dB

)))

|(% style="width:103px" %)(((

371

PM2.5 / CO2

372

)))|(% style="width:91px" %)0x08|(% style="width:116px" %)(((

373

PM2.5: 01000μg/m^^3^^

374

375

CO2: 0~~5000ppm

376

)))|(% style="width:88px" %)0x02|(% style="width:181px" %)(((

0x0023=35μg/m^^3 ^^

0x04fb=1275ppm

)))

|(% style="width:103px" %)PM10|(% style="width:91px" %)0x09|(% style="width:116px" %)(((

382

PM10: 01000μg/m^^3^^

383

)))|(% style="width:88px" %)0x02|(% style="width:181px" %)(((

0x002D=45μg/m^^3 ^^

)))

0x2748/10=1005.6kPa

)))

(((

Below is an example payload: 0FF60100000000012F00280001000400AD025E0117023E0023003203ED0001678390A102FFFF

)))

(((

When sending this payload to LoRaWAN server. WSC2-L will send this in one uplink or several uplinks according to LoRaWAN spec requirement. For example, total length of Payload is 54 bytes.

)))

* (((

When WSC2-L sending in US915 frequency DR0 data rate. Because this data rate has limitation of 11 bytes payload for each uplink. The payload will be split into below packets and uplink.

)))

(((

Uplink 1: [[image:image-20240418135453-1.png||height="26" width="202"]](% style="display:none" %)

)))

(((

Uplink 2: [[image:image-20240418141234-5.png||height="38" width="352"]](% style="display:none" %)

)))

* (((

When WSC2-L sending in EU868 frequency DR0 data rate. The payload will be split into below packets and uplink:

)))

(((

Uplink 1: [[image:image-20240418141304-6.png||height="39" width="408"]]

425

)))

426

427

Uplink 2: [[image:image-20240418141312-7.png||height="24" width="74"]]

428

429

430

=== 2.4.3 Decoder in TTN V3 ===

(((

In LoRaWAN platform, user only see HEX payload by default, user needs to use payload formatters to decode the payload to see human-readable value.

)))

(((

Download decoder for suitable platform from: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]

)))

(((

and put as below:

)))

[[image:image-20240413140757-2.png||height="423" width="892"]]

446

447

448

== 2.5 Show data on Application Server ==

(((

Application platform provides a human friendly interface to show the sensor data, once we have sensor data in TTN V3, we can use Datacake to connect to TTN V3 and see the data in Datacake. Below are the steps:

)))

(((

(% style="color:blue" %)**Step 1**(%%): Be sure that your device is programmed and properly connected to the LoRaWAN network.

)))

(((

(% style="color:blue" %)**Step 2**(%%): Configure your Application to forward data to Datacake you will need to add integration. Go to TTN V3 Console ~-~-> Applications ~-~-> Integrations ~-~-> Add Integrations.

461

)))

462

463

[[image:1656051197172-131.png]]

**Add TagoIO:**

[[image:1656051223585-631.png]]

**Authorization:**

[[image:1656051248318-368.png]]

476

477

478

In TagoIO console ([[https:~~/~~/admin.tago.io~~/~~/>>url:https://datacake.co/]]) , add WSC2-L:

479

480

481

[[image:1656051277767-168.png]]

482

483

484

== 2.6 Frequency Plans ==

485

486

487

The WSC2-L uses OTAA mode and below frequency plans by default. Each frequency band use different firmware, user update the firmware to the corresponding band for their country.

488

489

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]

490

491

492

= 3. Configure WSC2-L =

493

494

== 3.1 Configure Methods ==

495

496

497

WSC2-L supports below configure method:

498

499

* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].

500

501

* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].

502

503

* LoRaWAN Downlink. Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.

504

505

== 3.2 General Commands ==

506

507

508

These commands are to configure:

509

510

* General system settings like: uplink interval.

511

* LoRaWAN protocol & radio related command.

512

513

They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:

514

515

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]

516

517

518

== 3.3 Commands special design for WSC2-L ==

519

520

521

These commands only valid for WSC2-L, as below:

522

523

524

=== 3.3.1 Set Transmit Interval Time ===

525

526

527

Feature: Change LoRaWAN End Node Transmit Interval.

528

529

(% style="color:#037691" %)**AT Command: AT+TDC**

530

531

(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:501px" %)

532

|(% style="background-color:#4f81bd; color:white; width:155px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:166px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:180px" %)**Response**

533

|(% style="width:155px" %)AT+TDC=?|(% style="width:162px" %)Show current transmit Interval|(% style="width:177px" %)(((

534

30000

535

OK

536

the interval is 30000ms = 30s

537

)))

538

|(% style="width:155px" %)AT+TDC=60000|(% style="width:162px" %)Set Transmit Interval|(% style="width:177px" %)(((

539

OK

540

Set transmit interval to 60000ms = 60 seconds

541

)))

542

543

(% style="color:#037691" %)**Downlink Command: 0x01**

544

545

Format: Command Code (0x01) followed by 3 bytes time value.

546

547

If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.

548

549

* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds

550

* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds

551

552

=== 3.3.2 Set the CO2 or PM mode ===

553

554

555

(% style="color:red" %)**Note: Default shipment is CO2 sensor, optional CO2 or PM sensor is available at the time of purchase, which needs to be modified according to the sensor selected at the time of purchase.**

556

557

Feature: Set the CO2/PM mode, and the user can set the corresponding mode according to the purchased sensor.

558

559

(% style="color:#037691" %)**AT Command:**

560

561

(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:466px" %)

562

|(% style="background-color:#4f81bd; color:white; width:156px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:225px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:85px" %)**Response**

563

|(% style="width:155px" %)AT+PMMOD=1|(% style="width:224px" %)The working sensors are PM2.5 and PM10|(% style="width:84px" %)(((

OK

)))

|(% style="width:155px" %)AT+PMMOD=0|(% style="width:224px" %)The working sensors are CO2|(% style="width:84px" %)(((

OK

)))

(% style="color:#037691" %)**Downlink Command:**

572

573

* 0xE101 Same as: AT+PMMOD=1

574

* 0xE100 Same as: AT+PMMOD=0

575

576

=== 3.3.3 Add or Delete RS485 Sensor ===

(((

Feature: User can add or delete 3^^rd^^ party sensor as long they are RS485/Modbus interface,baud rate support 4800.Maximum can add 4 sensors.

)))

(((

(% style="color:#037691" %)**AT Command: **

)))

(((

(% style="color:blue" %)**AT+DYSENSOR=Type_Code, Query_Length, Query_Command , Read_Length , Valid_Data ,has_CRC,timeout**

)))

* (((

Type_Code range: A1 ~~ A4

593

)))

594

* (((

595

Query_Length: RS485 Query frame length, Value cannot be greater than 10

596

)))

597

* (((

598

Query_Command: RS485 Query frame data to be sent to sensor, cannot be larger than 10 bytes

599

)))

600

* (((

601

Read_Length: RS485 response frame length supposed to receive. Max can receive

602

)))

603

* (((

604

Valid_Data: valid data from RS485 Response, Valid Data will be added to Payload and upload via LoRaWAN.

605

)))

606

* (((

607

has_CRC: RS485 Response crc check (0: no verification required 1: verification required). If CRC=1 and CRC error, valid data will be set to 0.

608

)))

609

* (((

610

timeout: RS485 receive timeout (uint:ms). Device will close receive window after timeout

)))

(((

**Example:**

)))

(((

User need to change external sensor use the type code as address code.

)))

(((

With a 485 sensor, after correctly changing the address code to A1, the RS485 query frame is shown in the following table:

623

)))

624

625

[[image:image-20220624143553-10.png]]

626

627

628

The response frame of the sensor is as follows:

629

630

[[image:image-20220624143618-11.png]]

631

632

633

**Then the following parameters should be:**

634

635

* Address_Code range: A1

636

* Query_Length: 8

637

* Query_Command: A103000000019CAA

638

* Read_Length: 8

639

* Valid_Data: 23 (Indicates that the data length is 2 bytes, starting from the 3th byte)

640

* has_CRC: 1

641

* timeout: 1500 (Fill in the test according to the actual situation)

642

643

**So the input command is:**

644

645

AT+DYSENSOR=A1,8,A103000000019CAA,8,24,1,1500

646

647

648

In every sampling. WSC2-L will auto append the sensor segment as per this structure and uplink.

649

650

(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:351px" %)

651

|=(% style="width: 95px;background-color:#4F81BD;color:white" %)Type Code|=(% style="width: 122px;background-color:#4F81BD;color:white" %)Length (Bytes)|=(% style="width: 134px;background-color:#4F81BD;color:white" %)Measured Value

652

|(% style="width:94px" %)A1|(% style="width:121px" %)2|(% style="width:132px" %)0x000A

653

654

**Related commands:**

655

656

AT+DYSENSOR=A1,0 ~-~-> Delete 3^^rd^^ party sensor A1.

657

658

AT+DYSENSOR ~-~-> List All 3^^rd^^ Party Sensor. Like below:

659

660

661

(% style="color:#037691" %)**Downlink Command: **

662

663

**delete custom sensor A1:**

664

665

* 0xE5A1 Same as: AT+DYSENSOR=A1,0

666

667

**Remove all custom sensors**

* 0xE5FF

=== 3.3.4 RS485 Test Command ===

672

673

674

(% style="color:#037691" %)**AT Command:**

675

676

(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:494px" %)

677

|=(% style="width: 160px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 248px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 86px;background-color:#4F81BD;color:white" %)**Response**

678

|(% style="width:159px" %)AT+RSWRITE=xxxxxx|(% style="width:227px" %)(((

679

Send command to 485 sensor. Range : no more than 10 bytes

680

)))|(% style="width:85px" %)OK

681

682

Eg: Send command **01 03 00 00 00 01 84 0A** to 485 sensor

683

684

AT+RSWRITE=0103000001840A

685

686

687

(% style="color:#037691" %)**Downlink Command:**

688

689

* 0xE20103000001840A Same as: AT+RSWRITE=0103000001840A

690

691

=== 3.3.5 RS485 response timeout ===

692

693

694

Feature: Set or get extended time to receive 485 sensor data.

695

696

(% style="color:#037691" %)**AT Command:**

697

698

(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:433px" %)

699

|=(% style="width: 157px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 190px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 86px;background-color:#4F81BD;color:white" %)**Response**

700

|(% style="width:157px" %)AT+DTR=1000|(% style="width:188px" %)(((

701

Set response timeout to: Range : 0~~10000

702

)))|(% style="width:85px" %)OK

703

704

(% style="color:#037691" %)**Downlink Command:**

705

706

Format: Command Code (0xE0) followed by 3 bytes time value.

707

708

If the downlink payload=E0000005, it means set the END Node's Transmit Interval to 0x000005=5(S), while type code is E0.

709

710

* Example 1: Downlink Payload: E0000005 ~/~/ Set Transmit Interval (DTR) = 5 seconds

711

* Example 2: Downlink Payload: E000000A ~/~/ Set Transmit Interval (DTR) = 10 seconds

712

713

=== 3.3.6 Set or get the total count value ===

714

715

716

Feature: The user can set the counting to start from the set value according to the requirements. (only available in counting mode).

717

718

(% style="color:#037691" %)**AT Command:**

719

720

(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:433px" %)

721

|=(% style="width: 157px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 190px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 86px;background-color:#4F81BD;color:white" %)**Response**

722

|(% style="width:157px" %)AT+SETCNT=1000|(% style="width:188px" %)Set the total count to start from 1000|(% style="width:85px" %)OK

723

724

(% style="color:#037691" %)**Downlink Command:**

725

726

Format: Command Code (0x09) followed by 4 bytes time value.

727

728

If the downlink payload=09000003E8, This means that the count of the END node will start counting from setting 0x000003E8=1000 (times). while type code is 09.

729

730

* Example 1: Downlink Payload: 09000003E8 ~/~/ Set the value to start counting from 1000 = 1000 (times)

731

732

=== 3.3.7 Set interrupt or counting mode ===

733

734

735

Feature: Users can set the trigger mode to counting mode or interrupt mode as needed.

736

737

(% style="color:#037691" %)**AT Command:**

738

739

(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:433px" %)

740

|=(% style="width: 157px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 190px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 86px;background-color:#4F81BD;color:white" %)**Response**

741

|(% style="width:157px" %)AT+COUNTMOD=0|(% style="width:188px" %)set to interrupt mode|(% style="width:85px" %)OK

742

|(% style="width:157px" %)AT+COUNTMOD=1|(% style="width:188px" %)(((

743

set to counting mode

744

)))|(% style="width:85px" %)OK

745

746

(% style="color:#037691" %)**Downlink Command:**

747

748

Format: Command Code (0x10) followed by 1 bytes time value.

749

750

If the downlink payload=10 00, Set the trigger mode to interrupt mode, while type code is 10.

751

752

* Example 1: Downlink Payload: 10 00 ~/~/ Same as: AT+COUNTMOD=0 set to interrupt mode

753

754

== 3.4 Add 3rd RS485 / Modbus Sensor ==

755

756

=== 3.4.1 Hardware Connection ===

757

758

759

WSC2-L has a 1 to 3 cables. All the three connectors has same defination as below. It include Five Pins: VCC, GND, RS485-A, RS485-B, Count.

760

761

(% style="color:red" %)**Notice: RS485-A,RS485-B can be used to connect multiply sensors. but the COUNT can be only use for one sensor. Which means if you already add a Pulse output Rain Guage in the system, you are not able to add another Pulse Output device.**

762

763

[[image:image-20240707220859-4.png||height="313" width="366"]]

764

765

766

=== 3.4.2 Software Setup ===

767

768

769

Send AT+DYSENSOR to activate the RS485 sensor for collecting 3rd RS485 sensor. You can refer to the instructions in section 3.3.3 of the manual.

770

771

For example: AT+DYSENSOR=A1,8,A103000000019CAA,8,24,1,1500

772

773

774

=== 3.4.3 Payload ===

775

776

[[image:image-20240416163658-1.png]]

777

778

For example: A1 02 00 00

779

780

A1 : A1 register data acquisition instruction

781

782

02 : The valid data returned is 2 bytes in total.

783

784

00 00 : Return valid data

785

786

787

== 3.5 Add tipping bucket total solar radiation sensor ==

788

789

=== 3.5.1 Hardware Connection ===

790

791

792

The following is an example of connecting a total solar radiation sensor to a matching interface cable, and then using the interface to connect the WSC2-L.

793

794

Users can also choose to connect the sensor directly to the WSC2-L via the cable and pin instructions below.

795

796

The following is an explanation of the [[pins>>||anchor="H5.7PinMapping"]] required for WSC2-L：

797

798

**A:** RS485-A (Connect the RS485 sensor)

799

800

**B:** RS485-B (Connect the RS485 sensor)

801

802

**GPIO_EXTI:** Interrupt pin (Can be used to connect an additionally added pulsed rain gauge)

803

804

805

* Total Solar Radiation Sensor Cable Descripti

806

807

[[image:image-20240906174635-2.jpeg||height="430" width="813"]]

* Mating Interface Cable Description

812

813

[[image:image-20240906173843-1.jpeg||height="404" width="815"]]

* Connect to WSC2-L

The Total solar radiation sensor does not need to connect the interrupt pin, so the white cable is not wired.

818

819

[[image:image-20240906182250-3.jpeg||height="442" width="820"]]

820

821

822

=== 3.5.2 Calculating & Decode ===

823

824

825

0FC6 01 00000000 00EB 000F 0000 0003 008E 0251 00CE 0213 0017 001B 03EC 000000DE 90 A1020000 A2020032

826

827

For example: A2 02 00 32

828

829

A2 : A2 register data acquisition instruction

830

831

02 : The valid data returned is 2 bytes in total.

832

833

00 32(HEX) : Return valid data = 50(DEC)W/m2

834

835

836

== 3.6 MSP mode(Since version 1.1.5) ==

837

838

(% style="color:red" %)**Note:This feature is available for WSS-02.**

839

840

This function is used for the continuous collection of wind speed.

841

842

When MSP mode is turned on (AT+MSP=1), WSC1-L will collect real-time wind speed **every 10 seconds**. Then it will judge the maximum wind speed in this period according to the wind speed collected in TDC time, and calculate the average wind speed according to the wind speed data collected in TDC time and the number of data groups.

843

844

(% style="color:#037691" %)**AT Command:**

845

846

(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:433px" %)

847

|=(% style="width: 157px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 190px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 86px;background-color:#4F81BD;color:white" %)**Response**

848

|(% style="width:157px" %)AT+MSP=1|(% style="width:188px" %)Enable MSP mode|(% style="width:85px" %)OK

849

|(% style="width:157px" %)AT+MSP=0|(% style="width:188px" %)Disable MSP mode|(% style="width:85px" %)OK

850

851

(% style="color:#037691" %)**Downlink Command:**

852

853

Format: Command Code (0x34) followed by 1 bytes time value.

854

855

If the downlink payload=3400, then set the MSP mode to enable and the type code is 34.

856

857

* Example 1: Downlink Payload: 34 01 ~/~/ Same as: AT+MSP=1 set to enable MSP mode.

858

* Example 1: Downlink Payload: 34 00 ~/~/ Same as: AT+MSP=1 set to disable MSP mode.

859

860

(% style="color:red" %)**Note**(%%):

861

862

~1. When MSP mode is enabled, the uplink payload is increased by 4 bytes, the average wind speed from the last uplink to this one (2 bytes) and the maximum wind speed from the last uplink to this one (2 bytes).

863

864

2. If WSS-09 and WSS-22 are connected at the same time, the uplink payload will prioritize WSS-09 as follows:

865

866

867

== 3.7 Set the registers read by the rain gauge(Since firmware V1.1.1, only applicable to WSS-21) ==

868

869

870

(% style="color:#037691" %)**AT Command:**

871

872

(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)

873

|=(% style="width: 192px; background-color: rgb(79, 129, 189); color: white;" %)**Command Example**|=(% style="width: 209px; background-color: rgb(79, 129, 189); color: white;" %)**Function**|=(% style="width: 107px; background-color: rgb(79, 129, 189); color: white;" %)**Response**

874

|(% style="width:192px" %)(((

875

AT+RAINFALLSWITCH=?

876

)))|(% style="width:209px" %)Query the current register read by the rain gauge|(% style="width:107px" %)OK

877

|(% style="width:192px" %)AT+RAINFALLSWITCH=10|(% style="width:209px" %)Set to read the rainfall within 24 hours|(% style="width:107px" %)(((

OK

)))

(% style="color:#037691" %)**Downlink Command:**

882

883

* 0xE703 Same as: AT+RAINFALLSWITCH=3

Value Definition:

* **3**: The total rainfall after the sensor is powered on (for example Total rainfall: 166.5mm)

888

* **4**: Hourly rainfall: 0.2mm

889

* **5**: Rainfall in last hour: 0.2mm

890

* **6**: 24-hour maximum rainfall 10.0mm

891

* **8**: 24-hour minimum rainfall:0.0mm

892

* **10**: Rainfall in 24 hours: 8.0mm (Rainfall in the last 24 hours)

893

894

= 4. Power consumption and battery =

895

896

== 4.1 Total Power Consumption ==

897

898

899

Dragino Weather Station serial products include the main process unit (WSC2-L) and various sensors. The total power consumption equal total power of all above units. The power consumption for main process unit WSC2-L is 18ma @ 12v. and the power consumption of each sensor can be found on the Sensors chapter.

900

901

902

== 4.2 Reduce power consumption ==

903

904

905

The main process unit WSC2-L is set to LoRaWAN Class C by default. If user want to reduce the power consumption of this unit, user can set it to run in Class A. In Class A mode, WSC2-L will not be to get real-time downlink command from IoT Server.

== 4.3 Battery ==

(((

All sensors are only power by external power source. If external power source is off. All sensor won't work.

)))

(((

Main Process Unit WSC2-L is powered by both external power source and internal 1000mAh rechargeable battery. If external power source is off, WSC2-L still runs and can send periodically uplinks, but the sensors value will become invalid. External power source can recharge the 1000mAh rechargeable battery.

)))

= 5. Main Process Unit WSC2-L =

921

922

923

WSC2-L is the main process unit in Dragino Weather Station solution. WSC2-L is an an outdoor LoRaWAN RS485 end node. It is powered by external 12v solar power and have a built-in Li-ion backup battery.

924

925

WSC2-L reads value from various sensors and upload these sensor data to IoT server via LoRaWAN wireless protocol.

926

927

WSC2-L is full compatible with LoRaWAN Class A protocol, it can work with standard LoRaWAN gateway.

928

929

WSC2-L Supports BLE configure and wireless OTA update which make user easy to use.

930

931

Each WSC2-L is pre-load with a set of unique keys for LoRaWAN registration, register these keys to local LoRaWAN server and it will auto connect after power on.

== 5.1 Features ==

* LoRaWAN v1.0.3 Class A protocol.

938

* RS485 / Modbus protocol

939

* Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915

940

* AT Commands to change parameters

941

* Downlink to change configure

942

* Powered by external 12v battery

943

* Back up rechargeable 1000mAh battery

944

* IP Rating: IP65

945

* Support default sensors or 3rd party RS485 sensors

946

* Support Bluetooth v5.1 and LoRaWAN remote configure

947

* Support wireless OTA update firmware

948

* Wall Attachable.

949

950

== 5.2 Power Consumption ==

951

952

953

WSC2-L (without external sensor): Idle: 4mA, Transmit: max 40mA

954

955

956

== 5.3 Storage & Operation Temperature ==

-20°C to +60°C

== 5.4 Sleep mode and working mode ==

963

964

965

(% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.

966

967

(% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.

968

969

970

== 5.5 Button & LEDs ==

971

972

973

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]

974

975

(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)

976

|=(% style="width: 167px;background-color:#4F81BD;color:white" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 226px;background-color:#4F81BD;color:white" %)**Action**

977

|[[image:1749524241393-180.png]] 1~~3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((

978

If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.

979

Meanwhile, BLE module will be active and user can connect via BLE to configure device.

980

)))

981

|[[image:1749524243713-196.png]] >3s|(% style="width:117px" %)Active Device|(% style="width:225px" %)(((

982

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.

983

(% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

984

Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.

985

)))

986

|[[image:1749524287726-592.png]] x5|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.

987

988

== 5.6 BLE connection ==

989

990

991

WSC2-L supports BLE remote configure.

992

993

BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:

994

995

* Press button to send an uplink

996

* Press button to active device.

997

* Device Power on or reset.

998

999

If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.

1000

1001

1002

== 5.7 Pin Mapping ==

1003

1004

1005

[[image:image-20240412165523-2.png]]

1006

1007

1008

== 5.8 Pin Mapping ==

1009

1010

=== 5.8.1 One tow four main wires ===

1011

1012

[[image:image-20250529090933-1.jpeg||height="553" width="872"]]

1013

1014

1015

* Black line <~-~-~-~-~-~-> GND of battery charging motherboard (-)

1016

* Red line <~-~-~-~-~-~-> GND of battery charging motherboard (+)

1017

* White line <~-~-~-~-~-~-> A pin of WSC2-L motherboard

1018

* Green line <~-~-~-~-~-~-> B pin of WSC2-L motherboard

1019

* Yellow line <~-~-~-~-~-~-> GPIO_EXIT pin of WSC2-L motherboard

1020

1021

=== 5.8.2 Single line: ===

1022

1023

[[image:image-20250529100822-2.jpeg||height="505" width="854"]]

1024

1025

1026

* Black line <~-~-~-~-~-~-> Power (-) pin

1027

* Red line <~-~-~-~-~-~-> Power (+) pin

1028

* White line <~-~-~-~-~-~-> RS485-A pin

1029

* Green line <~-~-~-~-~-~-> RS485-B pin

1030

* Yellow line <~-~-~-~-~-~-> Pulse interrupt pin

1031

* Orange line <~-~-~-~-~-~-> Not used (can be cut off)

== 5.9 Mechanical ==

Refer LSn50v3 enclosure drawing in: [[https:~~/~~/www.dropbox.com/scl/fo/ztlw35a9xbkomu71u31im/ADY2192VNMFoMmryPGdwkRk/LoRaWAN%20End%20Node/SN50v3-LB/Mechinical?dl=0&rlkey=ojjcsw927eaow01dgooldq3nu&subfolder_nav_tracking=1>>https://www.dropbox.com/scl/fo/ztlw35a9xbkomu71u31im/ADY2192VNMFoMmryPGdwkRk/LoRaWAN%20End%20Node/SN50v3-LB/Mechinical?dl=0&rlkey=ojjcsw927eaow01dgooldq3nu&subfolder_nav_tracking=1]]

1037

1038

1039

= 6. OTA Firmware update =

1040

1041

1042

(% class="wikigeneratedid" %)

1043

**User can change firmware WSC2-L to:**

1044

1045

* Change Frequency band/ region.

1046

* Update with new features.

1047

* Fix bugs.

1048

1049

**Firmware and changelog can be downloaded from :** **[[Firmware download link>>https://www.dropbox.com/sh/8j3ioji411ni9gu/AADnOw3ErB1REsthKilfaq_Pa?dl=0]]**

1050

1051

**Methods to Update Firmware:**

1052

1053

* (Recommanded way) OTA firmware update via wireless: **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]**

1054

1055

* Update through UART TTL interface: **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.

= 7. FAQ =

== 7.1 What else do I need to purchase to build Weather Station? ==

1060

1061

1062

Below is the installation photo and structure:

1063

1064

[[image:image-20240413172530-3.png]]

1065

1066

== 7.2 Where can i find the modbus command for the WSS-09 sensor? ==

1067

1068

See this link for the [[modbus command set>>https://www.dropbox.com/scl/fo/ztlw35a9xbkomu71u31im/AK7twfUnkB4qKMvtU4XcEss/LoRaWAN%20End%20Node/WSC2-L%20Combine%20Weather%20Station%20Kit?dl=0&e=2&preview=Weather_Sensors_Modbus_Command_List.xlsx&rlkey=ojjcsw927eaow01dgooldq3nu&subfolder_nav_tracking=1]].

1069

1070

1071

= 8. Trouble Shooting =

1072

1073

== 8.1 What should I do when the RS485 sensor cannot collect data? ==

1074

1075

1076

~1. Recheck whether the sensor's power supply voltage is 12V at maximum.

1077

1078

2. Recheck whether the A and B signal lines of the sensor are connected reversely.

1079

1080

3. Check whether the sensor's transmission baud rate is 4800. If not, please change it to 4800 and try reading again.

1081

1082

1083

== 8.2 Why does the weather station make electric current sounds during operation? ==

1084

1085

1086

~1. Because a certain amount of sound will be produced during long-term power supply operation. This is a normal phenomenon and does not affect use.

1087

1088

1089

== 8.3 How to solve the problem of temperature difference in weather stations? ==

1090

1091

1092

You can use AT+RSWRITE (downlink: E2 xx xx xx xx xx xx xx ) to modify the temperature compensation function in the weather station.

**For example：**

When the temperature of the weather station is 3°C different from the right value, you can use AT+RSWRITE=01 06 00 50 00 1E 09 D3 (downlink: E2 01 06 00 50 00 1E 09 D3) to modify the temperature compensation value of the weather station to +3°C .

1097

1098

1099

== 8.4 Why does the rain gauge have no data? ==

1100

1101

1102

The default mode of the rain gauge is trigger mode.

1103

When it rains, it will trigger an uplink, and the data does not include rainfall data.

1104

If you want to query rainfall data, please change to counting mode

1105

1106

Feature: Users can set the trigger mode to counting mode or interrupt mode as needed.

1107

1108

(% style="color:#037691" %)**AT Command:**

1109

1110

(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:433px" %)

1111

|=(% style="width: 157px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 190px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 86px;background-color:#4F81BD;color:white" %)**Response**

1112

|(% style="width:157px" %)AT+COUNTMOD=0|(% style="width:188px" %)set to interrupt mode|(% style="width:85px" %)OK

1113

|(% style="width:157px" %)AT+COUNTMOD=1|(% style="width:188px" %)(((

1114

set to counting mode

1115

)))|(% style="width:85px" %)OK

1116

1117

(% style="color:#037691" %)**Downlink Command:**

1118

1119

Format: Command Code (0x10) followed by 1 bytes time value.

1120

1121

If the downlink payload=10 00, Set the trigger mode to interrupt mode, while type code is 10.

1122

1123

* Example 1: Downlink Payload: 10 00 ~/~/ Same as: AT+COUNTMOD=0 set to interrupt mode

= 9. Order Info =

(% style="color:red" %)**Please note that the WSC2-L only includes the wireless transmitter, and the WSS-08, WSS-09, WSS-21, WSS-22, WSS-23, WSS-24, WSS-25, WSS-26, WSS-27 sensor need to be purchased separately. If you need to connect more than 3 sensors, please purchase an additional one to four adapter cable (DR-F6C-4M).**

**Part Number:**

(% style="color:blue" %)**Wireless Transmitter :**(%%)** WSC2-L-XX **

1134

1135

**XX**: the default frequency band

1136

1137

* **AS923**: LoRaWAN AS923 band

1138

* **AU915**: LoRaWAN AU915 band

1139

* **EU433**: LoRaWAN EU433 band

1140

* **EU868**: LoRaWAN EU868 band

1141

* **KR920**: LoRaWAN KR920 band

1142

* **S915**: LoRaWAN US915 band

1143

* **IN865**: LoRaWAN IN865 band

1144

* **CN470**: LoRaWAN CN470 band

1145

1146

(% style="color:green" %)**Sensors Option :**(%%)** WSS-08, WSS-09, WSS-21, WSS-22, WSS-23, WSS-24, WSS-25, WSS-26, WSS-27**

= 10. Support =

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1153

1154

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]].

Wiki source code of WSC2-L -- Weather Station Kit User Manual

Applications

Navigation