Last modified by Bei Jinggeng on 2025/01/10 15:51
<
From version < 13.1 >
edited by Edwin Chen
on 2023/05/11 23:11
To version < 37.1 >
edited by Saxer Lin
on 2023/05/13 12:52
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Edwin
1 +XWiki.Saxer
Content
... ... @@ -122,7 +122,7 @@
122 122  == 1.7 Pin Definitions ==
123 123  
124 124  
125 -[[image:image-20230511203450-2.png||height="443" width="785"]]
125 +[[image:image-20230513102034-2.png]]
126 126  
127 127  
128 128  == 1.8 Mechanical ==
... ... @@ -288,14 +288,35 @@
288 288  1. All modes share the same Payload Explanation from HERE.
289 289  1. By default, the device will send an uplink message every 20 minutes.
290 290  
291 -
292 292  ==== 2.3.2.1  MOD~=1 (Default Mode) ====
293 293  
294 294  In this mode, uplink payload includes in total 11 bytes. Uplink packets use FPORT=2.
295 295  
296 -|**Size(bytes)**|**2**|**2**|**2**|**1**|**2**|**2**
297 -|**Value**|Bat|Temperature(DS18B20)|ADC|Digital in & Digital Interrupt|Temperature（SHT20 or SHT31 or BH1750 Illumination Sensor|Humidity（SHT20)
295 +|**Size(bytes)**|**2**|**2**|**2**|(% style="width:216px" %)**1**|(% style="width:342px" %)**2**|(% style="width:171px" %)**2**
296 +|**Value**|Bat|(((
297 +Temperature(DS18B20)
298 298  
299 +(PC13)
300 +)))|(((
301 +ADC
302 +
303 +(PA4)
304 +)))|(% style="width:216px" %)(((
305 +Digital in(PB15) &
306 +
307 +Digital Interrupt(PA8)
308 +
309 +
310 +)))|(% style="width:342px" %)(((
311 +Temperature
312 +
313 +(SHT20 or SHT31 or BH1750 Illumination Sensor)
314 +)))|(% style="width:171px" %)(((
315 +Humidity
316 +
317 +(SHT20 or SHT31)
318 +)))
319 +
299 299  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627150949-6.png?rev=1.1||alt="image-20220627150949-6.png"]]
300 300  
301 301  
... ... @@ -306,7 +306,17 @@
306 306  |**Size(bytes)**|**2**|**2**|**2**|**1**|**2**|**2**
307 307  |**Value**|BAT|(((
308 308  Temperature(DS18B20)
309 -)))|ADC|Digital in & Digital Interrupt|(((
330 +
331 +(PC13)
332 +)))|(((
333 +ADC
334 +
335 +(PA4)
336 +)))|(((
337 +Digital in(PB15) &
338 +
339 +Digital Interrupt(PA8)
340 +)))|(((
310 310  Distance measure by:
311 311  1) LIDAR-Lite V3HP
312 312  Or
... ... @@ -317,18 +317,30 @@
317 317  
318 318  **Connection of LIDAR-Lite V3HP:**
319 319  
320 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656324581381-162.png?rev=1.1||alt="1656324581381-162.png"]]
351 +[[image:image-20230512173758-5.png||height="563" width="712"]]
321 321  
322 322  **Connection to Ultrasonic Sensor:**
323 323  
324 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656324598488-204.png?rev=1.1||alt="1656324598488-204.png"]]
355 +Need to remove R1 and R2 resistors to get low power,otherwise there will be 240uA standby current.
325 325  
357 +[[image:image-20230512173903-6.png||height="596" width="715"]]
358 +
326 326  For the connection to TF-Mini or TF-Luna , MOD2 payload is as below:
327 327  
328 328  |**Size(bytes)**|**2**|**2**|**1**|**2**|**2**|**2**
329 329  |**Value**|BAT|(((
330 330  Temperature(DS18B20)
331 -)))|Digital in & Digital Interrupt|ADC|(((
364 +
365 +(PC13)
366 +)))|(((
367 +Digital in(PB15) &
368 +
369 +Digital Interrupt(PA8)
370 +)))|(((
371 +ADC
372 +
373 +(PA4)
374 +)))|(((
332 332  Distance measure by:1)TF-Mini plus LiDAR
333 333  Or 
334 334  2) TF-Luna LiDAR
... ... @@ -338,98 +338,120 @@
338 338  
339 339  **Connection to [[TF-Mini plus>>url:http://en.benewake.com/product/detail/5c345cd0e5b3a844c472329b.html]] LiDAR(UART version):**
340 340  
341 -Need to remove R3 and R4 resistors to get low power. Since firmware v1.7.0
384 +Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.
342 342  
343 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656376795715-436.png?rev=1.1||alt="1656376795715-436.png"]]
386 +[[image:image-20230512180609-7.png||height="555" width="802"]]
344 344  
345 345  **Connection to [[TF-Luna>>url:http://en.benewake.com/product/detail/5e1c1fd04d839408076b6255.html]] LiDAR (UART version):**
346 346  
347 -Need to remove R3 and R4 resistors to get low power. Since firmware v1.7.0
390 +Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.
348 348  
349 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656376865561-355.png?rev=1.1||alt="1656376865561-355.png"]]
392 +[[image:image-20230513105207-4.png||height="469" width="802"]]
350 350  
351 -Please use firmware version > 1.6.5 when use MOD=2, in this firmware version, user can use LSn50 v1 to power the ultrasonic sensor directly and with low power consumption.
352 352  
353 -
354 354  ==== 2.3.2.3  MOD~=3 (3 ADC + I2C) ====
355 355  
356 356  This mode has total 12 bytes. Include 3 x ADC + 1x I2C
357 357  
399 +(% style="width:1031px" %)
358 358  |=(((
359 359  **Size(bytes)**
360 -)))|=**2**|=**2**|=**2**|=**1**|=2|=2|=1
361 -|**Value**|ADC(Pin PA0)|ADC2(PA1)|ADC3 (PA4)|(((
362 -Digital in(PA12)&Digital Interrupt1(PB14)
363 -)))|Temperature（SHT20 or SHT31 or BH1750 Illumination Sensor）|Humidity（SHT20 or SHT31)|Bat
402 +)))|=(% style="width: 68px;" %)**2**|=(% style="width: 75px;" %)**2**|=**2**|=**1**|=(% style="width: 304px;" %)2|=(% style="width: 163px;" %)2|=(% style="width: 53px;" %)1
403 +|**Value**|(% style="width:68px" %)(((
404 +ADC1
364 364  
365 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656377431497-975.png?rev=1.1||alt="1656377431497-975.png"]]
406 +(PA4)
407 +)))|(% style="width:75px" %)(((
408 +ADC2
366 366  
410 +(PA5)
411 +)))|(((
412 +ADC3
367 367  
368 -==== 2.3.2.4 MOD~=4 (3 x DS18B20) ====
414 +(PA8)
415 +)))|(((
416 +Digital Interrupt(PB15)
417 +)))|(% style="width:304px" %)(((
418 +Temperature
369 369  
370 -This mode is supported in firmware version since v1.6.1. Software set to AT+MOD=4
420 +(SHT20 or SHT31 or BH1750 Illumination Sensor)
421 +)))|(% style="width:163px" %)(((
422 +Humidity
371 371  
372 -Hardware connection is as below,
424 +(SHT20 or SHT31)
425 +)))|(% style="width:53px" %)Bat
373 373  
374 -**( Note:**
427 +[[image:image-20230513110214-6.png]]
375 375  
376 -* In hardware version v1.x and v2.0 , R3 & R4 should change from 10k to 4.7k ohm to support the other 2 x DS18B20 probes.
377 -* In hardware version v2.1 no need to change R3 , R4, by default, they are 4.7k ohm already.
378 378  
379 -See [[here>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H1.6A0HardwareChangelog]] for hardware changelog. **) **
430 +==== 2.3.2.4 MOD~=4 (3 x DS18B20) ====
380 380  
381 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656377461619-156.png?rev=1.1||alt="1656377461619-156.png"]]
432 +[[image:image-20230512170701-3.png||height="565" width="743"]]
382 382  
383 383  This mode has total 11 bytes. As shown below:
384 384  
385 -|**Size(bytes)**|**2**|**2**|**2**|**1**|**2**|**2**
386 -|**Value**|BAT|(((
387 -Temperature1
388 -(DS18B20)
389 -(PB3)
390 -)))|ADC|Digital in & Digital Interrupt|Temperature2
391 -(DS18B20)
392 -(PA9)|Temperature3
393 -(DS18B20)
394 -(PA10)
436 +(% style="width:1017px" %)
437 +|**Size(bytes)**|**2**|(% style="width:186px" %)**2**|(% style="width:82px" %)**2**|(% style="width:210px" %)**1**|(% style="width:191px" %)**2**|(% style="width:183px" %)**2**
438 +|**Value**|BAT|(% style="width:186px" %)(((
439 +Temperature1(DS18B20)
440 +(PC13)
441 +)))|(% style="width:82px" %)(((
442 +ADC
395 395  
444 +(PA4)
445 +)))|(% style="width:210px" %)(((
446 +Digital in(PB15) &
447 +
448 +Digital Interrupt(PA8) 
449 +)))|(% style="width:191px" %)Temperature2(DS18B20)
450 +(PB9)|(% style="width:183px" %)Temperature3(DS18B20)
451 +(PB8)
452 +
396 396  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656377606181-607.png?rev=1.1||alt="1656377606181-607.png"]]
397 397  
398 -(% class="wikigeneratedid" %)
399 -=== ===
400 400  
401 401  ==== 2.3.2.5  MOD~=5(Weight Measurement by HX711) ====
402 402  
403 -This mode is supported in firmware version since v1.6.2. Please use v1.6.5 firmware version so user no need to use extra LDO for connection.
458 +[[image:image-20230512164658-2.png||height="532" width="729"]]
404 404  
405 -
406 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378224664-860.png?rev=1.1||alt="1656378224664-860.png"]]
407 -
408 408  Each HX711 need to be calibrated before used. User need to do below two steps:
409 409  
410 410  1. Zero calibration. Don't put anything on load cell and run **AT+WEIGRE** to calibrate to Zero gram.
411 411  1. Adjust calibration factor (default value 400): Put a known weight thing on load cell and run **AT+WEIGAP** to adjust the Calibration Factor.
412 412  1. (((
413 -Remove the limit of plus or minus 5Kg in mode 5, and expand from 2 bytes to 4 bytes, the unit is g.(Since v1.8.0)
465 +Weight has 4 bytes, the unit is g.
414 414  )))
415 415  
416 416  For example:
417 417  
418 -**AT+WEIGAP =403.0**
470 +**AT+GETSENSORVALUE =0**
419 419  
420 420  Response:  Weight is 401 g
421 421  
422 422  Check the response of this command and adjust the value to match the real value for thing.
423 423  
476 +(% style="width:982px" %)
424 424  |=(((
425 425  **Size(bytes)**
426 -)))|=**2**|=**2**|=**2**|=**1**|=**4**|=2
427 -|**Value**|[[Bat>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.1BatteryInfo]]|[[Temperature(DS18B20)>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.2Temperature28DS18B2029]]|[[ADC>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.4AnalogueDigitalConverter28ADC29]]|[[Digital Input and Digitak Interrupt>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.3DigitalInput]]|Weight|Reserved
479 +)))|=**2**|=(% style="width: 282px;" %)**2**|=(% style="width: 119px;" %)**2**|=(% style="width: 279px;" %)**1**|=(% style="width: 106px;" %)**4**
480 +|**Value**|BAT|(% style="width:282px" %)(((
481 +Temperature(DS18B20)
428 428  
483 +(PC13)
484 +
485 +
486 +)))|(% style="width:119px" %)(((
487 +ADC
488 +
489 +(PA4)
490 +)))|(% style="width:279px" %)(((
491 +Digital in(PB15) &
492 +
493 +Digital Interrupt(PA8)
494 +)))|(% style="width:106px" %)Weight
495 +
429 429  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220820120036-2.png?width=1003&height=469&rev=1.1||alt="image-20220820120036-2.png" height="469" width="1003"]]
430 430  
431 -(% class="wikigeneratedid" %)
432 -=== ===
433 433  
434 434  ==== 2.3.2.6  MOD~=6 (Counting Mode) ====
435 435  
... ... @@ -437,89 +437,133 @@
437 437  
438 438  Connection is as below. The PIR sensor is a count sensor, it will generate interrupt when people come close or go away. User can replace the PIR sensor with other counting sensors.
439 439  
440 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378351863-572.png?rev=1.1||alt="1656378351863-572.png"]]
505 +[[image:image-20230512181814-9.png||height="543" width="697"]]
441 441  
442 -**Note:** LoRaWAN wireless transmission will infect the PIR sensor. Which cause the counting value increase +1 for every uplink. User can change PIR sensor or put sensor away of the LSN50 to avoid this happen.
507 +**Note:** LoRaWAN wireless transmission will infect the PIR sensor. Which cause the counting value increase +1 for every uplink. User can change PIR sensor or put sensor away of the SN50_v3 to avoid this happen.
443 443  
444 -|=**Size(bytes)**|=**2**|=**2**|=**2**|=**1**|=**4**
445 -|**Value**|[[BAT>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.1BatteryInfo]]|(((
446 -[[Temperature(DS18B20)>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.2Temperature28DS18B2029]]
447 -)))|[[ADC>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.4AnalogueDigitalConverter28ADC29]]|[[Digital in>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.3DigitalInput]]|Count
509 +(% style="width:961px" %)
510 +|=**Size(bytes)**|=**2**|=(% style="width: 256px;" %)**2**|=(% style="width: 108px;" %)**2**|=(% style="width: 126px;" %)**1**|=(% style="width: 145px;" %)**4**
511 +|**Value**|BAT|(% style="width:256px" %)(((
512 +Temperature(DS18B20)
448 448  
514 +(PC13)
515 +)))|(% style="width:108px" %)(((
516 +ADC
517 +
518 +(PA4)
519 +)))|(% style="width:126px" %)(((
520 +Digital in
521 +
522 +(PB15)
523 +)))|(% style="width:145px" %)(((
524 +Count
525 +
526 +(PA8)
527 +)))
528 +
449 449  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378441509-171.png?rev=1.1||alt="1656378441509-171.png"]]
450 450  
451 451  
452 452  ==== 2.3.2.7  MOD~=7 (Three interrupt contact modes) ====
453 453  
454 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220820140109-3.png?rev=1.1||alt="image-20220820140109-3.png"]]
455 -
456 456  |=(((
457 457  **Size(bytes)**
458 458  )))|=**2**|=**2**|=**2**|=**1**|=**1**|=1|=2
459 -|**Value**|BAT|Temperature(DS18B20)|ADC|(((
460 -Digital in(PA12)&Digital Interrupt1(PB14)
461 -)))|Digital Interrupt2(PB15)|Digital Interrupt3(PA4)|Reserved
537 +|**Value**|BAT|(((
538 +Temperature(DS18B20)
462 462  
540 +(PC13)
541 +)))|(((
542 +ADC
463 463  
544 +(PA5)
545 +)))|(((
546 +Digital Interrupt1(PA8)
547 +)))|Digital Interrupt2(PA4)|Digital Interrupt3(PB15)|Reserved
548 +
549 +[[image:image-20230513111203-7.png||height="324" width="975"]]
550 +
464 464  ==== 2.3.2.8  MOD~=8 （3ADC+1DS18B20） ====
465 465  
553 +(% style="width:917px" %)
466 466  |=(((
467 467  **Size(bytes)**
468 -)))|=**2**|=**2**|=**2**|=**1**|=**2**|=2
469 -|**Value**|BAT|Temperature(DS18B20)|(((
470 -ADC1(PA0)
471 -)))|(((
472 -Digital in
473 -& Digital Interrupt(PB14)
474 -)))|(((
475 -ADC2(PA1)
476 -)))|(((
477 -ADC3(PA4)
556 +)))|=**2**|=(% style="width: 207px;" %)**2**|=(% style="width: 94px;" %)**2**|=(% style="width: 198px;" %)**1**|=(% style="width: 84px;" %)**2**|=(% style="width: 79px;" %)2
557 +|**Value**|BAT|(% style="width:207px" %)(((
558 +Temperature(DS18B20)
559 +
560 +(PC13)
561 +)))|(% style="width:94px" %)(((
562 +ADC1
563 +
564 +(PA4)
565 +)))|(% style="width:198px" %)(((
566 +Digital Interrupt(PB15)
567 +)))|(% style="width:84px" %)(((
568 +ADC2
569 +
570 +(PA5)
571 +)))|(% style="width:79px" %)(((
572 +ADC3
573 +
574 +(PA8)
478 478  )))
479 479  
480 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220823164903-2.png?rev=1.1||alt="image-20220823164903-2.png"]]
577 +[[image:image-20230513111231-8.png||height="335" width="900"]]
481 481  
482 -(% class="wikigeneratedid" %)
483 -=== ===
484 484  
485 485  ==== 2.3.2.9  MOD~=9 (3DS18B20+ two Interrupt count mode) ====
486 486  
582 +(% style="width:1010px" %)
487 487  |=(((
488 488  **Size(bytes)**
489 -)))|=**2**|=**2**|=**2**|=**1**|=**2**|=4|=4
585 +)))|=**2**|=**2**|=**2**|=**1**|=(% style="width: 193px;" %)**2**|=(% style="width: 78px;" %)4|=(% style="width: 78px;" %)4
490 490  |**Value**|BAT|(((
491 -Temperature1(PB3)
587 +Temperature1(DS18B20)
588 +
589 +(PC13)
492 492  )))|(((
493 -Temperature2(PA9)
591 +Temperature2(DS18B20)
592 +
593 +(PB9)
494 494  )))|(((
495 -Digital in
496 -& Digital Interrupt(PA4)
497 -)))|(((
498 -Temperature3(PA10)
499 -)))|(((
500 -Count1(PB14)
501 -)))|(((
502 -Count2(PB15)
595 +Digital Interrupt
596 +
597 +(PB15)
598 +)))|(% style="width:193px" %)(((
599 +Temperature3(DS18B20)
600 +
601 +(PB8)
602 +)))|(% style="width:78px" %)(((
603 +Count1
604 +
605 +(PA8)
606 +)))|(% style="width:78px" %)(((
607 +Count2
608 +
609 +(PA4)
503 503  )))
504 504  
505 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220823165322-3.png?rev=1.1||alt="image-20220823165322-3.png"]]
612 +[[image:image-20230513111255-9.png||height="341" width="899"]]
506 506  
507 507  **The newly added AT command is issued correspondingly:**
508 508  
509 -**~ AT+INTMOD1** ** PB14**  pin：  Corresponding downlink:  **06 00 00 xx**
616 +**~ AT+INTMOD1** ** PA8**  pin：  Corresponding downlink:  **06 00 00 xx**
510 510  
511 -**~ AT+INTMOD2**  **PB15** pin：  Corresponding downlink:**  06 00 01 xx**
618 +**~ AT+INTMOD2**  **PA4**  pin：  Corresponding downlink:**  06 00 01 xx**
512 512  
513 -**~ AT+INTMOD3**  **PA4**  pin：  Corresponding downlink:  ** 06 00 02 xx**
620 +**~ AT+INTMOD3**  **PB15**  pin：  Corresponding downlink:  ** 06 00 02 xx**
514 514  
515 515  **AT+SETCNT=aa,bb** 
516 516  
517 -When AA is 1, set the count of PB14 pin to BB Corresponding downlink：09 01 bb bb bb bb
624 +When AA is 1, set the count of PA8 pin to BB Corresponding downlink：09 01 bb bb bb bb
518 518  
519 -When AA is 2, set the count of PB15 pin to BB Corresponding downlink：09 02 bb bb bb bb
626 +When AA is 2, set the count of PA4 pin to BB Corresponding downlink：09 02 bb bb bb bb
520 520  
521 -=== 2.3.10  ​Decode payload in The Things Network ===
522 522  
629 +
630 +=== 2.3.3  ​Decode payload ===
631 +
523 523  While using TTN V3 network, you can add the payload format to decode the payload.
524 524  
525 525  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378466788-734.png?rev=1.1||alt="1656378466788-734.png"]]
... ... @@ -526,39 +526,28 @@
526 526  
527 527  The payload decoder function for TTN V3 are here:
528 528  
529 -LSN50 TTN V3 Payload Decoder:  [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]
638 +SN50v3 TTN V3 Payload Decoder:  [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]
530 530  
531 531  
532 -Sensor Data is uplink via FPORT=2
641 +==== 2.3.3.1 Battery Info ====
533 533  
534 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
535 -|=(% style="width: 90px;background-color:#D9E2F3" %)(((
536 -**Size(bytes)**
537 -)))|=(% style="width: 80px;background-color:#D9E2F3" %)2|=(% style="width: 90px;background-color:#D9E2F3" %)4|=(% style="width:80px;background-color:#D9E2F3" %)1|=(% style="width: 80px;background-color:#D9E2F3" %)**2**|=(% style="width: 80px;background-color:#D9E2F3" %)2
538 -|(% style="width:99px" %)**Value**|(% style="width:69px" %)(((
539 -[[Battery>>||anchor="HBattery:"]]
540 -)))|(% style="width:130px" %)(((
541 -[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]
542 -)))|(% style="width:91px" %)(((
543 -[[Alarm Flag>>||anchor="HAlarmFlag26MOD:"]]
544 -)))|(% style="width:103px" %)(((
545 -[[Temperature>>||anchor="HTemperature:"]]
546 -)))|(% style="width:80px" %)(((
547 -[[Humidity>>||anchor="HHumidity:"]]
548 -)))
643 +Check the battery voltage for SN50v3.
549 549  
550 -==== (% style="color:#4472c4" %)**Battery**(%%) ====
551 -
552 -Sensor Battery Level.
553 -
554 554  Ex1: 0x0B45 = 2885mV
555 555  
556 556  Ex2: 0x0B49 = 2889mV
557 557  
558 558  
650 +==== 2.3.3.2  Temperature (DS18B20) ====
559 559  
560 -==== (% style="color:#4472c4" %)**Temperature**(%%) ====
652 +If there is a DS18B20 connected to PB3 pin. The temperature will be uploaded in the payload.
561 561  
654 +More DS18B20 can check the [[3 DS18B20 mode>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#2.3.4MOD3D4283xDS18B2029]]
655 +
656 +**Connection:**
657 +
658 +[[image:image-20230512180718-8.png||height="538" width="647"]]
659 +
562 562  **Example**:
563 563  
564 564  If payload is: 0105H:  (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree
... ... @@ -568,195 +568,208 @@
568 568  （FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）
569 569  
570 570  
571 -==== (% style="color:#4472c4" %)**Humidity**(%%) ====
669 +==== 2.3.3.3 Digital Input ====
572 572  
671 +The digital input for pin PB15,
573 573  
574 -Read:0x(0197)=412    Value:  412 / 10=41.2, So 41.2%
673 +* When PB15 is high, the bit 1 of payload byte 6 is 1.
674 +* When PB15 is low, the bit 1 of payload byte 6 is 0.
575 575  
676 +(% class="wikigeneratedid" id="H2.3.3.4A0AnalogueDigitalConverter28ADC29" %)
677 +(((
678 +When the digital interrupt pin is set to AT+INTMODx=0, this pin is used as a digital input pin.
576 576  
577 -==== (% style="color:#4472c4" %)**Alarm Flag& MOD**(%%) ====
680 +**Note:**The maximum voltage input supports 3.6V.
681 +)))
578 578  
683 +==== 2.3.3.4  Analogue Digital Converter (ADC) ====
579 579  
580 -**Example:**
685 +The measuring range of the ADC is only about 0V to 1.1V The voltage resolution is about 0.24mv.
581 581  
582 -If payload & 0x01 = 0x01  **~-~->** This is an Alarm Message
687 +When the measured output voltage of the sensor is not within the range of 0V and 1.1V, the output voltage terminal of the sensor shall be divided The example in the following figure is to reduce the output voltage of the sensor by three times If it is necessary to reduce more times, calculate according to the formula in the figure and connect the corresponding resistance in series.
583 583  
584 -If payload & 0x01 = 0x00  **~-~->** This is a normal uplink message, no alarm
689 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220628150112-1.png?width=285&height=241&rev=1.1||alt="image-20220628150112-1.png" height="241" width="285"]]
585 585  
586 -If payload >> 2 = 0x00  **~-~->**  means MOD=1, This is a sampling uplink message
691 +**Note:**If the ADC type sensor needs to be powered by SN50_v3, it is recommended to use +5V to control its switch.Only sensors with low power consumption can be powered with VDD.
587 587  
588 -If payload >> 2 = 0x31  **~-~->**  means MOD=31, this message is a reply message for polling, this message contains the alarm settings. see [[this link>>path:#HPolltheAlarmsettings:]] for detail. 
693 +==== 2.3.3.5 Digital Interrupt ====
589 589  
695 +Digital Interrupt refers to pin PA8, and there are different trigger methods. When there is a trigger, the SN50v3 will send a packet to the server.
590 590  
591 -== 2.4 Payload Decoder file ==
697 +**~ Interrupt connection method:**
592 592  
699 +[[image:image-20230513105351-5.png||height="147" width="485"]]
593 593  
594 -In TTN, use can add a custom payload so it shows friendly reading
701 +**Example to use with door sensor :**
595 595  
596 -In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:
703 +The door sensor is shown at right. It is a two wire magnetic contact switch used for detecting the open/close status of doors or windows.
597 597  
598 -[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B >>https://github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B]]
705 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379210849-860.png?rev=1.1||alt="1656379210849-860.png"]]
599 599  
707 +When the two pieces are close to each other, the 2 wire output will be short or open (depending on the type), while if the two pieces are away from each other, the 2 wire output will be the opposite status. So we can use SN50_v3 interrupt interface to detect the status for the door or window.
600 600  
601 -== 2.5 Datalog Feature ==
709 +**~ Below is the installation example:**
602 602  
711 +Fix one piece of the magnetic sensor to the door and connect the two pins to SN50_v3 as follows:
603 603  
604 -Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, S31x-LB will store the reading for future retrieving purposes.
713 +* (((
714 +One pin to SN50_v3's PA8 pin
715 +)))
716 +* (((
717 +The other pin to SN50_v3's VDD pin
718 +)))
605 605  
720 +Install the other piece to the door. Find a place where the two pieces will be close to each other when the door is closed. For this particular magnetic sensor, when the door is closed, the output will be short, and PA8 will be at the VCC voltage.
606 606  
607 -=== 2.5.1 Ways to get datalog via LoRaWAN ===
722 +Door sensors have two types: ** NC (Normal close)** and **NO (normal open)**. The connection for both type sensors are the same. But the decoding for payload are reverse, user need to modify this in the IoT Server decoder.
608 608  
724 +When door sensor is shorted, there will extra power consumption in the circuit, the extra current is 3v3/R14 = 3v3/1Mohm = 3uA which can be ignored.
609 609  
610 -Set [[PNACKMD=1>>||anchor="H2.5.4DatalogUplinkpayloadA028FPORT3D329"]], S31x-LB will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
726 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379283019-229.png?rev=1.1||alt="1656379283019-229.png"]]
611 611  
612 -* a) S31x-LB will do an ACK check for data records sending to make sure every data arrive server.
613 -* b) S31x-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB gets a ACK, S31x-LB will consider there is a network connection and resend all NONE-ACK messages.
728 +The above photos shows the two parts of the magnetic switch fitted to a door.
614 614  
615 -Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
730 +The software by default uses the falling edge on the signal line as an interrupt. We need to modify it to accept both the rising edge (0v ~-~-> VCC , door close) and the falling edge (VCC ~-~-> 0v , door open) as the interrupt.
616 616  
617 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="图片-20220703111700-2.png" height="381" width="1119"]]
732 +The command is:
618 618  
619 -=== 2.5.2 Unix TimeStamp ===
734 +**AT+INTMOD1=1       **~/~/(more info about INMOD please refer** **[[**AT Command Manual**>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/&file=DRAGINO_LSN50_AT_Commands_v1.5.1.pdf]]**. **)
620 620  
736 +Below shows some screen captures in TTN V3:
621 621  
622 -S31x-LB uses Unix TimeStamp format based on
738 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379339508-835.png?rev=1.1||alt="1656379339508-835.png"]]
623 623  
624 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
740 +In MOD=1, user can use byte 6 to see the status for door open or close. TTN V3 decoder is as below:
625 625  
626 -User can get this time from link:  [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
742 +door= (bytes[6] & 0x80)? "CLOSE":"OPEN";
627 627  
628 -Below is the converter example
629 629  
630 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1||alt="图片-20220523001219-12.png" height="298" width="720"]]
745 +==== 2.3.3.6 I2C Interface (SHT20 & SHT31) ====
631 631  
632 -So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
747 +The SDA and SCK are I2C interface lines. You can use these to connect to an I2C device and get the sensor data.
633 633  
749 +We have made an example to show how to use the I2C interface to connect to the SHT20 Temperature and Humidity Sensor.
634 634  
635 -=== 2.5.3 Set Device Time ===
751 +Notice: Different I2C sensors have different I2C commands set and initiate process, if user want to use other I2C sensors, User need to re-write the source code to support those sensors. SHT20 code in SN50_v3 will be a good reference.
636 636  
753 +Below is the connection to SHT20/ SHT31. The connection is as below:
637 637  
638 -User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
639 639  
640 -Once S31x-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to S31x-LB. If S31x-LB fails to get the time from the server, S31x-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
756 +[[image:image-20230513103633-3.png||height="636" width="1017"]]
641 641  
642 -(% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
758 +The device will be able to get the I2C sensor data now and upload to IoT Server.
643 643  
760 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379664142-345.png?rev=1.1||alt="1656379664142-345.png"]]
644 644  
645 -=== 2.5.4 Datalog Uplink payload (FPORT~=3) ===
762 +Convert the read byte to decimal and divide it by ten.
646 646  
764 +**Example:**
647 647  
648 -The Datalog uplinks will use below payload format.
766 +Temperature:  Read:0116(H) = 278(D)  Value:  278 /10=27.8℃;
649 649  
650 -**Retrieval data payload:**
768 +Humidity:    Read:0248(H)=584(D)  Value:  584 / 10=58.4, So 58.4%
651 651  
652 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
653 -|=(% style="width: 80px;background-color:#D9E2F3" %)(((
654 -**Size(bytes)**
655 -)))|=(% style="width: 60px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 60px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 120px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 103px; background-color: rgb(217, 226, 243);" %)**1**|=(% style="width: 85px; background-color: rgb(217, 226, 243);" %)**4**
656 -|(% style="width:103px" %)**Value**|(% style="width:54px" %)(((
657 -[[Temp_Black>>||anchor="HTemperatureBlack:"]]
658 -)))|(% style="width:51px" %)[[Temp_White>>||anchor="HTemperatureWhite:"]]|(% style="width:89px" %)[[Temp_ Red or Temp _White>>||anchor="HTemperatureREDorTemperatureWhite:"]]|(% style="width:103px" %)Poll message flag & Ext|(% style="width:54px" %)[[Unix Time Stamp>>||anchor="H2.5.2UnixTimeStamp"]]
770 +If you want to use other I2C device, please refer the SHT20 part source code as reference.
659 659  
660 -**Poll message flag & Ext:**
661 661  
662 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20221006192726-1.png?width=754&height=112&rev=1.1||alt="图片-20221006192726-1.png" height="112" width="754"]]
773 +==== 2.3.3.7  ​Distance Reading ====
663 663  
664 -**No ACK Message**:  1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for **PNACKMD=1** feature)
775 +Refer [[Ultrasonic Sensor section>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.8UltrasonicSensor]].
665 665  
666 -**Poll Message Flag**: 1: This message is a poll message reply.
667 667  
668 -* Poll Message Flag is set to 1.
778 +==== 2.3.3.8 Ultrasonic Sensor ====
669 669  
670 -* Each data entry is 11 bytes, to save airtime and battery, devices will send max bytes according to the current DR and Frequency bands.
780 +This Fundamental Principles of this sensor can be found at this link: [[https:~~/~~/wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU~~_~~__SEN0208>>url:https://wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU___SEN0208]]
671 671  
672 -For example, in US915 band, the max payload for different DR is:
782 +The SN50_v3 detects the pulse width of the sensor and converts it to mm output. The accuracy will be within 1 centimeter. The usable range (the distance between the ultrasonic probe and the measured object) is between 24cm and 600cm.
673 673  
674 -**a) DR0:** max is 11 bytes so one entry of data
784 +The working principle of this sensor is similar to the **HC-SR04** ultrasonic sensor.
675 675  
676 -**b) DR1:** max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
786 +The picture below shows the connection:
677 677  
678 -**c) DR2:** total payload includes 11 entries of data
788 +[[image:image-20230512173903-6.png||height="596" width="715"]]
679 679  
680 -**d) DR3: **total payload includes 22 entries of data.
790 +Connect to the SN50_v3 and run **AT+MOD=2** to switch to ultrasonic mode (ULT).
681 681  
682 -If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0   
792 +The ultrasonic sensor uses the 8^^th^^ and 9^^th^^ byte for the measurement value.
683 683  
684 -
685 685  **Example:**
686 686  
687 -If S31x-LB has below data inside Flash:
796 +Distance:  Read: 0C2D(Hex) = 3117(D)  Value:  3117 mm=311.7 cm
688 688  
689 -[[image:1682646494051-944.png]]
690 690  
691 -If user sends below downlink command: 3160065F9760066DA705
692 692  
693 -Where : Start time: 60065F97 = time 21/1/19 04:27:03
800 +==== 2.3.3.9  Battery Output - BAT pin ====
694 694  
695 - Stop time: 60066DA7= time 21/1/19 05:27:03
802 +The BAT pin of SN50v3 is connected to the Battery directly. If users want to use BAT pin to power an external sensor. User need to make sure the external sensor is of low power consumption. Because the BAT pin is always open. If the external sensor is of high power consumption. the battery of SN50v3-LB will run out very soon.
696 696  
697 697  
698 -**S31x-LB will uplink this payload.**
805 +==== 2.3.3.10  +5V Output ====
699 699  
700 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-13.png?width=727&height=421&rev=1.1||alt="图片-20220523001219-13.png" height="421" width="727"]]
807 +SN50v3 will enable +5V output before all sampling and disable the +5v after all sampling. 
701 701  
702 -(((
703 -__**7FFF089801464160065F97**__ **__7FFF__ __088E__ __014B__ __41__ __60066009__** 7FFF0885014E41600660667FFF0875015141600662BE7FFF086B015541600665167FFF08660155416006676E7FFF085F015A41600669C67FFF0857015D4160066C1E
704 -)))
809 +The 5V output time can be controlled by AT Command.
705 705  
706 -(((
707 -Where the first 11 bytes is for the first entry:
708 -)))
811 +**AT+5VT=1000**
709 709  
710 -(((
711 -7FFF089801464160065F97
712 -)))
813 +Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.
713 713  
714 -(((
715 -**Ext sensor data**=0x7FFF/100=327.67
716 -)))
815 +By default the AT+5VT=500. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.
717 717  
718 -(((
719 -**Temp**=0x088E/100=22.00
720 -)))
721 721  
722 -(((
723 -**Hum**=0x014B/10=32.6
724 -)))
725 725  
726 -(((
727 -**poll message flag & Ext**=0x41,means reply data,Ext=1
728 -)))
819 +==== 2.3.3.11  BH1750 Illumination Sensor ====
729 729  
730 -(((
731 -**Unix time** is 0x60066009=1611030423s=21/1/19 04:27:03
732 -)))
821 +MOD=1 support this sensor. The sensor value is in the 8^^th^^ and 9^^th^^ bytes.
733 733  
823 +[[image:image-20230512172447-4.png||height="593" width="1015"]]
734 734  
735 -(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的
825 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220628110012-12.png?rev=1.1||alt="image-20220628110012-12.png"]]
736 736  
737 -== 2.6 Temperature Alarm Feature ==
738 738  
828 +==== 2.3.3.12  Working MOD ====
739 739  
740 -S31x-LB work flow with Alarm feature.
830 +The working MOD info is contained in the Digital in & Digital Interrupt byte (7^^th^^ Byte).
741 741  
832 +User can use the 3^^rd^^ ~~ 7^^th^^  bit of this byte to see the working mod:
742 742  
743 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-D20-D22-D23%20LoRaWAN%20Temperature%20Sensor%20User%20Manual/WebHome/image-20220623090437-1.png?rev=1.1||alt="图片-20220623090437-1.png"]]
834 +Case 7^^th^^ Byte >> 2 & 0x1f:
744 744  
836 +* 0: MOD1
837 +* 1: MOD2
838 +* 2: MOD3
839 +* 3: MOD4
840 +* 4: MOD5
841 +* 5: MOD6
842 +* 6: MOD7
843 +* 7: MOD8
844 +* 8: MOD9
745 745  
746 -== 2.7 Frequency Plans ==
846 +== 2.4 Payload Decoder file ==
747 747  
748 748  
749 -The S31x-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
849 +In TTN, use can add a custom payload so it shows friendly reading
750 750  
851 +In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:
852 +
853 +[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B >>https://github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B]]
854 +
855 +
856 +
857 +== 2.5 Frequency Plans ==
858 +
859 +
860 +The SN50v3-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
861 +
751 751  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
752 752  
753 753  
754 -= 3. Configure S31x-LB =
865 += 3. Configure SN50v3-LB =
755 755  
756 756  == 3.1 Configure Methods ==
757 757  
758 758  
759 -S31x-LB supports below configure method:
870 +SN50v3-LB supports below configure method:
760 760  
761 761  * AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
762 762  * AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
... ... @@ -775,7 +775,7 @@
775 775  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
776 776  
777 777  
778 -== 3.3 Commands special design for S31x-LB ==
889 +== 3.3 Commands special design for SN50v3-LB ==
779 779  
780 780  
781 781  These commands only valid for S31x-LB, as below:
... ... @@ -811,7 +811,6 @@
811 811  
812 812  === 3.3.2 Get Device Status ===
813 813  
814 -
815 815  Send a LoRaWAN downlink to ask device send Alarm settings.
816 816  
817 817  (% style="color:blue" %)**Downlink Payload:  **(%%)0x26 01
... ... @@ -819,108 +819,150 @@
819 819  Sensor will upload Device Status via FPORT=5. See payload section for detail.
820 820  
821 821  
822 -=== 3.3.3 Set Temperature Alarm Threshold ===
932 +=== 3.3.3 Set Interrupt Mode ===
823 823  
824 -* (% style="color:blue" %)**AT Command:**
825 825  
826 -(% style="color:#037691" %)**AT+SHTEMP=min,max**
935 +Feature, Set Interrupt mode for GPIO_EXIT.
827 827  
828 -* When min=0, and max≠0, Alarm higher than max
829 -* When min≠0, and max=0, Alarm lower than min
830 -* When min≠0 and max≠0, Alarm higher than max or lower than min
937 +(% style="color:blue" %)**AT Command: AT+INTMOD1，AT+INTMOD2，AT+INTMOD3**
831 831  
832 -Example:
939 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
940 +|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**
941 +|(% style="width:154px" %)AT+INTMOD1=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
942 +0
943 +OK
944 +the mode is 0 =Disable Interrupt
945 +)))
946 +|(% style="width:154px" %)AT+INTMOD1=2|(% style="width:196px" %)(((
947 +Set Transmit Interval
948 +0. (Disable Interrupt),
949 +~1. (Trigger by rising and falling edge)
950 +2. (Trigger by falling edge)
951 +3. (Trigger by rising edge)
952 +)))|(% style="width:157px" %)OK
953 +|(% style="width:154px" %)AT+INTMOD2=3|(% style="width:196px" %)(((
954 +Set Transmit Interval
833 833  
834 - AT+SHTEMP=0,30   ~/~/ Alarm when temperature higher than 30.
956 +trigger by rising edge.
957 +)))|(% style="width:157px" %)OK
958 +|(% style="width:154px" %)AT+INTMOD3=0|(% style="width:196px" %)Disable Interrupt|(% style="width:157px" %)OK
835 835  
836 -* (% style="color:blue" %)**Downlink Payload:**
960 +(% style="color:blue" %)**Downlink Command: 0x06**
837 837  
838 -(% style="color:#037691" %)**0x(0C 01 00 1E)**  (%%) ~/~/ Set AT+SHTEMP=0,30
962 +Format: Command Code (0x06) followed by 3 bytes.
839 839  
840 -(% style="color:red" %)**(note: 3^^rd^^ byte= 0x00 for low limit(not set), 4^^th^^ byte = 0x1E for high limit: 30)**
964 +This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
841 841  
966 +* Example 1: Downlink Payload: 06000000  **~-~-->**  AT+INTMOD1=0
967 +* Example 2: Downlink Payload: 06000003  **~-~-->**  AT+INTMOD1=3
968 +* Example 3: Downlink Payload: 06000102  **~-~-->**  AT+INTMOD2=2
969 +* Example 4: Downlink Payload: 06000201  **~-~-->**  AT+INTMOD3=1
842 842  
843 -=== 3.3.4 Set Humidity Alarm Threshold ===
971 +=== 3.3.4 Set Power Output Duration ===
844 844  
845 -* (% style="color:blue" %)**AT Command:**
973 +Control the output duration 5V . Before each sampling, device will
846 846  
847 -(% style="color:#037691" %)**AT+SHHUM=min,max**
975 +~1. first enable the power output to external sensor,
848 848  
849 -* When min=0, and max≠0, Alarm higher than max
850 -* When min≠0, and max=0, Alarm lower than min
851 -* When min≠0 and max≠0, Alarm higher than max or lower than min
977 +2. keep it on as per duration, read sensor value and construct uplink payload
852 852  
853 -Example:
979 +3. final, close the power output.
854 854  
855 - AT+SHHUM=70,0  ~/~/ Alarm when humidity lower than 70%.
981 +(% style="color:blue" %)**AT Command: AT+5VT**
856 856  
857 -* (% style="color:blue" %)**Downlink Payload:**
983 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
984 +|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**
985 +|(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)(((
986 +500(default)
858 858  
859 -(% style="color:#037691" %)**0x(0C 02 46 00)**(%%)  ~/~/ Set AT+SHTHUM=70,0
988 +OK
989 +)))
990 +|(% style="width:154px" %)AT+5VT=1000|(% style="width:196px" %)(((
991 +Close after a delay of 1000 milliseconds.
992 +)))|(% style="width:157px" %)OK
860 860  
861 -(% style="color:red" %)**(note: 3^^rd^^ byte= 0x46 for low limit (70%), 4^^th^^ byte = 0x00 for high limit (not set))**
994 +(% style="color:blue" %)**Downlink Command: 0x07**
862 862  
996 +Format: Command Code (0x07) followed by 2 bytes.
863 863  
864 -=== 3.3.5 Set Alarm Interval ===
998 +The first and second bytes are the time to turn on.
865 865  
866 -The shortest time of two Alarm packet. (unit: min)
1000 +* Example 1: Downlink Payload: 070000  **~-~-->**  AT+5VT=0
1001 +* Example 2: Downlink Payload: 0701F4  **~-~-->**  AT+5VT=500
867 867  
868 -* (% style="color:blue" %)**AT Command:**
1003 +=== 3.3.5 Set Weighing parameters ===
869 869  
870 -(% style="color:#037691" %)**AT+ATDC=30** (%%) ~/~/ The shortest interval of two Alarm packets is 30 minutes, Means is there is an alarm packet uplink, there won't be another one in the next 30 minutes.
1005 +Feature: Working mode 5 is effective, weight initialization and weight factor setting of HX711.
871 871  
872 -* (% style="color:blue" %)**Downlink Payload:**
1007 +(% style="color:blue" %)**AT Command: AT+WEIGRE,AT+WEIGAP**
873 873  
874 -(% style="color:#037691" %)**0x(0D 00 1E)**(%%)     **~-~--> ** Set AT+ATDC=0x 00 1E = 30 minutes
1009 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1010 +|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**
1011 +|(% style="width:154px" %)AT+WEIGRE|(% style="width:196px" %)Weight is initialized to 0.|(% style="width:157px" %)OK
1012 +|(% style="width:154px" %)AT+WEIGAP=？|(% style="width:196px" %)400.0|(% style="width:157px" %)OK(default)
1013 +|(% style="width:154px" %)AT+WEIGAP=400.3|(% style="width:196px" %)Set the factor to 400.3.|(% style="width:157px" %)OK
875 875  
1015 +(% style="color:blue" %)**Downlink Command: 0x08**
876 876  
877 -=== 3.3.6 Get Alarm settings ===
878 878  
1018 +Format: Command Code (0x08) followed by 2 bytes or 4 bytes.
879 879  
880 -Send a LoRaWAN downlink to ask device send Alarm settings.
1020 +Use AT+WEIGRE when the first byte is 1, only 1 byte. When it is 2, use AT+WEIGAP, there are 3 bytes.
881 881  
882 -* (% style="color:#037691" %)**Downlink Payload:  **(%%)0x0E 01
1022 +The second and third bytes are multiplied by 10 times to be the AT+WEIGAP value.
883 883  
884 -**Example:**
1024 +* Example 1: Downlink Payload: 0801  **~-~-->**  AT+WEIGRE
1025 +* Example 2: Downlink Payload: 08020FA3  **~-~-->**  AT+WEIGAP=400.3
1026 +* Example 3: Downlink Payload: 08020FA0  **~-~-->**  AT+WEIGAP=400.0
885 885  
886 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-D20-D22-D23%20LoRaWAN%20Temperature%20Sensor%20User%20Manual/WebHome/1655948182791-225.png?rev=1.1||alt="1655948182791-225.png"]]
1028 +=== 3.3.6 Set Digital pulse count value ===
887 887  
1030 +Feature: Set the pulse count value.
888 888  
889 -**Explain:**
1032 +Count 1 is PA8 pin of mode 6 and mode 9. Count 2 is PA4 pin of mode 9.
890 890  
891 -* Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.
1034 +(% style="color:blue" %)**AT Command: AT+SETCNT**
892 892  
893 -=== 3.3.7 Set Interrupt Mode ===
1036 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1037 +|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**
1038 +|(% style="width:154px" %)AT+SETCNT=1,100|(% style="width:196px" %)Initialize the count value 1 to 100.|(% style="width:157px" %)OK
1039 +|(% style="width:154px" %)AT+SETCNT=2,0|(% style="width:196px" %)Initialize the count value 2 to 0.|(% style="width:157px" %)OK
894 894  
1041 +(% style="color:blue" %)**Downlink Command: 0x09**
895 895  
896 -Feature, Set Interrupt mode for GPIO_EXIT.
897 897  
898 -(% style="color:blue" %)**AT Command: AT+INTMOD**
1044 +Format: Command Code (0x09) followed by 5 bytes.
899 899  
1046 +The first byte is to select which count value to initialize, and the next four bytes are the count value to be initialized.
1047 +
1048 +* Example 1: Downlink Payload: 090100000000  **~-~-->**  AT+SETCNT=1,0
1049 +* Example 2: Downlink Payload: 0902000003E8  **~-~-->**  AT+SETCNT=2,1000
1050 +
1051 +=== 3.3.7 Set Workmode ===
1052 +
1053 +Feature: Switch working mode.
1054 +
1055 +(% style="color:blue" %)**AT Command: AT+MOD**
1056 +
900 900  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
901 901  |=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**
902 -|(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
903 -0
1059 +|(% style="width:154px" %)AT+MOD=?|(% style="width:196px" %)Get the current working mode.|(% style="width:157px" %)(((
904 904  OK
905 -the mode is 0 =Disable Interrupt
906 906  )))
907 -|(% style="width:154px" %)AT+INTMOD=2|(% style="width:196px" %)(((
908 -Set Transmit Interval
909 -0. (Disable Interrupt),
910 -~1. (Trigger by rising and falling edge)
911 -2. (Trigger by falling edge)
912 -3. (Trigger by rising edge)
913 -)))|(% style="width:157px" %)OK
1062 +|(% style="width:154px" %)AT+MOD=4|(% style="width:196px" %)Set the working mode to 3DS18B20s.|(% style="width:157px" %)(((
1063 +OK
914 914  
915 -(% style="color:blue" %)**Downlink Command: 0x06**
1065 +Attention:Take effect after ATZ
1066 +)))
916 916  
917 -Format: Command Code (0x06) followed by 3 bytes.
1068 +(% style="color:blue" %)**Downlink Command: 0x0A**
918 918  
919 -This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
920 920  
921 -* Example 1: Downlink Payload: 06000000  ~/~/  Turn off interrupt mode
922 -* Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
1071 +Format: Command Code (0x0A) followed by 1 bytes.
923 923  
1073 +* Example 1: Downlink Payload: 0A01  **~-~-->**  AT+MOD=1
1074 +* Example 2: Downlink Payload: 0A04  **~-~-->**  AT+MOD=4
1075 +
924 924  = 4. Battery & Power Consumption =
925 925  
926 926  
... ... @@ -949,7 +949,10 @@
949 949  
950 950  = 6. FAQ =
951 951  
1104 +== 6.1 Where can i find source code of SN50v3-LB? ==
952 952  
1106 +* **[[Hardware Source Files>>https://github.com/dragino/Lora/tree/master/LSN50/v3.0]].**
1107 +* **[[Software Source Code & Compile instruction>>https://github.com/dragino/SN50v3]].**
953 953  
954 954  = 7. Order Info =
955 955  
image-20230512163509-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +1.5 MB
Content
image-20230512164658-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.0 MB
Content
image-20230512170701-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.5 MB
Content
image-20230512172447-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.0 MB
Content
image-20230512173758-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.1 MB
Content
image-20230512173903-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.3 MB
Content
image-20230512180609-7.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.3 MB
Content
image-20230512180718-8.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.3 MB
Content
image-20230512181814-9.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.2 MB
Content
image-20230513084523-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +611.3 KB
Content
image-20230513102034-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +607.1 KB
Content
image-20230513103633-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +595.5 KB
Content
image-20230513105207-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +384.7 KB
Content
image-20230513105351-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +37.6 KB
Content
image-20230513110214-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +172.7 KB
Content
image-20230513111203-7.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +79.9 KB
Content
image-20230513111231-8.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +64.9 KB
Content
image-20230513111255-9.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +70.4 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0