Last modified by Bei Jinggeng on 2025/01/10 15:51
<
From version < 13.1 >
edited by Edwin Chen
on 2023/05/11 23:11
To version < 27.1 >
edited by Saxer Lin
on 2023/05/13 08:45
>
Change comment: Uploaded new attachment "image-20230513084523-1.png", version {1}

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Edwin
1 +XWiki.Saxer
Content
... ... @@ -288,14 +288,25 @@
288 288  1. All modes share the same Payload Explanation from HERE.
289 289  1. By default, the device will send an uplink message every 20 minutes.
290 290  
291 -
292 292  ==== 2.3.2.1  MOD~=1 (Default Mode) ====
293 293  
294 294  In this mode, uplink payload includes in total 11 bytes. Uplink packets use FPORT=2.
295 295  
296 -|**Size(bytes)**|**2**|**2**|**2**|**1**|**2**|**2**
297 -|**Value**|Bat|Temperature(DS18B20)|ADC|Digital in & Digital Interrupt|Temperature（SHT20 or SHT31 or BH1750 Illumination Sensor|Humidity（SHT20)
295 +|**Size(bytes)**|**2**|**2**|**2**|(% style="width:216px" %)**1**|(% style="width:342px" %)**2**|(% style="width:171px" %)**2**
296 +|**Value**|Bat|(((
297 +Temperature(DS18B20)
298 298  
299 +(PC13)
300 +)))|(((
301 +ADC
302 +
303 +(PA4)
304 +)))|(% style="width:216px" %)(((
305 +Digital in & Digital Interrupt
306 +
307 +
308 +)))|(% style="width:342px" %)Temperature（SHT20 or SHT31 or BH1750 Illumination Sensor|(% style="width:171px" %)Humidity（SHT20 or SHT31)
309 +
299 299  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627150949-6.png?rev=1.1||alt="image-20220627150949-6.png"]]
300 300  
301 301  
... ... @@ -317,11 +317,11 @@
317 317  
318 318  **Connection of LIDAR-Lite V3HP:**
319 319  
320 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656324581381-162.png?rev=1.1||alt="1656324581381-162.png"]]
331 +[[image:image-20230512173758-5.png||height="563" width="712"]]
321 321  
322 322  **Connection to Ultrasonic Sensor:**
323 323  
324 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656324598488-204.png?rev=1.1||alt="1656324598488-204.png"]]
335 +[[image:image-20230512173903-6.png||height="596" width="715"]]
325 325  
326 326  For the connection to TF-Mini or TF-Luna , MOD2 payload is as below:
327 327  
... ... @@ -338,13 +338,13 @@
338 338  
339 339  **Connection to [[TF-Mini plus>>url:http://en.benewake.com/product/detail/5c345cd0e5b3a844c472329b.html]] LiDAR(UART version):**
340 340  
341 -Need to remove R3 and R4 resistors to get low power. Since firmware v1.7.0
352 +Need to remove R3 and R4 resistors to get low power.
342 342  
343 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656376795715-436.png?rev=1.1||alt="1656376795715-436.png"]]
354 +[[image:image-20230512180609-7.png||height="555" width="802"]]
344 344  
345 345  **Connection to [[TF-Luna>>url:http://en.benewake.com/product/detail/5e1c1fd04d839408076b6255.html]] LiDAR (UART version):**
346 346  
347 -Need to remove R3 and R4 resistors to get low power. Since firmware v1.7.0
358 +Need to remove R3 and R4 resistors to get low power.
348 348  
349 349  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656376865561-355.png?rev=1.1||alt="1656376865561-355.png"]]
350 350  
... ... @@ -357,10 +357,18 @@
357 357  
358 358  |=(((
359 359  **Size(bytes)**
360 -)))|=**2**|=**2**|=**2**|=**1**|=2|=2|=1
361 -|**Value**|ADC(Pin PA0)|ADC2(PA1)|ADC3 (PA4)|(((
371 +)))|=(% style="width: 68px;" %)**2**|=(% style="width: 75px;" %)**2**|=**2**|=**1**|=(% style="width: 318px;" %)2|=(% style="width: 172px;" %)2|=1
372 +|**Value**|(% style="width:68px" %)(((
373 +ADC
374 +
375 +(PA0)
376 +)))|(% style="width:75px" %)(((
377 +ADC2
378 +
379 +(PA1)
380 +)))|ADC3 (PA4)|(((
362 362  Digital in(PA12)&Digital Interrupt1(PB14)
363 -)))|Temperature（SHT20 or SHT31 or BH1750 Illumination Sensor）|Humidity（SHT20 or SHT31)|Bat
382 +)))|(% style="width:318px" %)Temperature（SHT20 or SHT31 or BH1750 Illumination Sensor）|(% style="width:172px" %)Humidity（SHT20 or SHT31)|Bat
364 364  
365 365  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656377431497-975.png?rev=1.1||alt="1656377431497-975.png"]]
366 366  
... ... @@ -367,69 +367,72 @@
367 367  
368 368  ==== 2.3.2.4 MOD~=4 (3 x DS18B20) ====
369 369  
370 -This mode is supported in firmware version since v1.6.1. Software set to AT+MOD=4
389 +[[image:image-20230512170701-3.png||height="565" width="743"]]
371 371  
372 -Hardware connection is as below,
391 +This mode has total 11 bytes. As shown below:
373 373  
374 -**( Note:**
393 +(% style="width:1017px" %)
394 +|**Size(bytes)**|**2**|(% style="width:186px" %)**2**|(% style="width:82px" %)**2**|(% style="width:210px" %)**1**|(% style="width:191px" %)**2**|(% style="width:183px" %)**2**
395 +|**Value**|BAT|(% style="width:186px" %)(((
396 +Temperature1(DS18B20)
397 +(PC13)
398 +)))|(% style="width:82px" %)(((
399 +ADC
375 375  
376 -* In hardware version v1.x and v2.0 , R3 & R4 should change from 10k to 4.7k ohm to support the other 2 x DS18B20 probes.
377 -* In hardware version v2.1 no need to change R3 , R4, by default, they are 4.7k ohm already.
401 +(PA4)
402 +)))|(% style="width:210px" %)(((
403 +Digital in & Digital Interrupt
378 378  
379 -See [[here>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H1.6A0HardwareChangelog]] for hardware changelog. **) **
405 +(PB15)  &  (PA8) 
406 +)))|(% style="width:191px" %)Temperature2(DS18B20)
407 +(PB9)|(% style="width:183px" %)Temperature3(DS18B20)
408 +(PB8)
380 380  
381 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656377461619-156.png?rev=1.1||alt="1656377461619-156.png"]]
382 -
383 -This mode has total 11 bytes. As shown below:
384 -
385 -|**Size(bytes)**|**2**|**2**|**2**|**1**|**2**|**2**
386 -|**Value**|BAT|(((
387 -Temperature1
388 -(DS18B20)
389 -(PB3)
390 -)))|ADC|Digital in & Digital Interrupt|Temperature2
391 -(DS18B20)
392 -(PA9)|Temperature3
393 -(DS18B20)
394 -(PA10)
395 -
396 396  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656377606181-607.png?rev=1.1||alt="1656377606181-607.png"]]
397 397  
398 -(% class="wikigeneratedid" %)
399 -=== ===
400 400  
401 401  ==== 2.3.2.5  MOD~=5(Weight Measurement by HX711) ====
402 402  
403 -This mode is supported in firmware version since v1.6.2. Please use v1.6.5 firmware version so user no need to use extra LDO for connection.
415 +[[image:image-20230512164658-2.png||height="532" width="729"]]
404 404  
405 -
406 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378224664-860.png?rev=1.1||alt="1656378224664-860.png"]]
407 -
408 408  Each HX711 need to be calibrated before used. User need to do below two steps:
409 409  
410 410  1. Zero calibration. Don't put anything on load cell and run **AT+WEIGRE** to calibrate to Zero gram.
411 411  1. Adjust calibration factor (default value 400): Put a known weight thing on load cell and run **AT+WEIGAP** to adjust the Calibration Factor.
412 412  1. (((
413 -Remove the limit of plus or minus 5Kg in mode 5, and expand from 2 bytes to 4 bytes, the unit is g.(Since v1.8.0)
422 +Weight has 4 bytes, the unit is g.
414 414  )))
415 415  
416 416  For example:
417 417  
418 -**AT+WEIGAP =403.0**
427 +**AT+GETSENSORVALUE =0**
419 419  
420 420  Response:  Weight is 401 g
421 421  
422 422  Check the response of this command and adjust the value to match the real value for thing.
423 423  
433 +(% style="width:982px" %)
424 424  |=(((
425 425  **Size(bytes)**
426 -)))|=**2**|=**2**|=**2**|=**1**|=**4**|=2
427 -|**Value**|[[Bat>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.1BatteryInfo]]|[[Temperature(DS18B20)>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.2Temperature28DS18B2029]]|[[ADC>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.4AnalogueDigitalConverter28ADC29]]|[[Digital Input and Digitak Interrupt>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.3DigitalInput]]|Weight|Reserved
436 +)))|=**2**|=(% style="width: 282px;" %)**2**|=(% style="width: 119px;" %)**2**|=(% style="width: 279px;" %)**1**|=(% style="width: 106px;" %)**4**
437 +|**Value**|[[Bat>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.1BatteryInfo]]|(% style="width:282px" %)(((
438 +[[Temperature(DS18B20)>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.2Temperature28DS18B2029]]
428 428  
440 +(PC13)
441 +
442 +
443 +)))|(% style="width:119px" %)(((
444 +[[ADC>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.4AnalogueDigitalConverter28ADC29]]
445 +
446 +(PA4)
447 +)))|(% style="width:279px" %)(((
448 +[[Digital Input and Digitak Interrupt>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.3DigitalInput]]
449 +
450 +(PB15)  &  (PA8)
451 +)))|(% style="width:106px" %)Weight
452 +
429 429  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220820120036-2.png?width=1003&height=469&rev=1.1||alt="image-20220820120036-2.png" height="469" width="1003"]]
430 430  
431 -(% class="wikigeneratedid" %)
432 -=== ===
433 433  
434 434  ==== 2.3.2.6  MOD~=6 (Counting Mode) ====
435 435  
... ... @@ -437,7 +437,7 @@
437 437  
438 438  Connection is as below. The PIR sensor is a count sensor, it will generate interrupt when people come close or go away. User can replace the PIR sensor with other counting sensors.
439 439  
440 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378351863-572.png?rev=1.1||alt="1656378351863-572.png"]]
462 +[[image:image-20230512181814-9.png||height="543" width="697"]]
441 441  
442 442  **Note:** LoRaWAN wireless transmission will infect the PIR sensor. Which cause the counting value increase +1 for every uplink. User can change PIR sensor or put sensor away of the LSN50 to avoid this happen.
443 443  
... ... @@ -460,7 +460,6 @@
460 460  Digital in(PA12)&Digital Interrupt1(PB14)
461 461  )))|Digital Interrupt2(PB15)|Digital Interrupt3(PA4)|Reserved
462 462  
463 -
464 464  ==== 2.3.2.8  MOD~=8 （3ADC+1DS18B20） ====
465 465  
466 466  |=(((
... ... @@ -479,8 +479,6 @@
479 479  
480 480  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220823164903-2.png?rev=1.1||alt="image-20220823164903-2.png"]]
481 481  
482 -(% class="wikigeneratedid" %)
483 -=== ===
484 484  
485 485  ==== 2.3.2.9  MOD~=9 (3DS18B20+ two Interrupt count mode) ====
486 486  
... ... @@ -518,8 +518,10 @@
518 518  
519 519  When AA is 2, set the count of PB15 pin to BB Corresponding downlink：09 02 bb bb bb bb
520 520  
521 -=== 2.3.10  ​Decode payload in The Things Network ===
522 522  
541 +
542 +=== 2.3.3  ​Decode payload ===
543 +
523 523  While using TTN V3 network, you can add the payload format to decode the payload.
524 524  
525 525  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378466788-734.png?rev=1.1||alt="1656378466788-734.png"]]
... ... @@ -526,39 +526,28 @@
526 526  
527 527  The payload decoder function for TTN V3 are here:
528 528  
529 -LSN50 TTN V3 Payload Decoder:  [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]
550 +SN50v3 TTN V3 Payload Decoder:  [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]
530 530  
531 531  
532 -Sensor Data is uplink via FPORT=2
553 +==== 2.3.3.1 Battery Info ====
533 533  
534 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
535 -|=(% style="width: 90px;background-color:#D9E2F3" %)(((
536 -**Size(bytes)**
537 -)))|=(% style="width: 80px;background-color:#D9E2F3" %)2|=(% style="width: 90px;background-color:#D9E2F3" %)4|=(% style="width:80px;background-color:#D9E2F3" %)1|=(% style="width: 80px;background-color:#D9E2F3" %)**2**|=(% style="width: 80px;background-color:#D9E2F3" %)2
538 -|(% style="width:99px" %)**Value**|(% style="width:69px" %)(((
539 -[[Battery>>||anchor="HBattery:"]]
540 -)))|(% style="width:130px" %)(((
541 -[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]
542 -)))|(% style="width:91px" %)(((
543 -[[Alarm Flag>>||anchor="HAlarmFlag26MOD:"]]
544 -)))|(% style="width:103px" %)(((
545 -[[Temperature>>||anchor="HTemperature:"]]
546 -)))|(% style="width:80px" %)(((
547 -[[Humidity>>||anchor="HHumidity:"]]
548 -)))
555 +Check the battery voltage for SN50v3.
549 549  
550 -==== (% style="color:#4472c4" %)**Battery**(%%) ====
551 -
552 -Sensor Battery Level.
553 -
554 554  Ex1: 0x0B45 = 2885mV
555 555  
556 556  Ex2: 0x0B49 = 2889mV
557 557  
558 558  
562 +==== 2.3.3.2  Temperature (DS18B20) ====
559 559  
560 -==== (% style="color:#4472c4" %)**Temperature**(%%) ====
564 +If there is a DS18B20 connected to PB3 pin. The temperature will be uploaded in the payload.
561 561  
566 +More DS18B20 can check the [[3 DS18B20 mode>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#2.3.4MOD3D4283xDS18B2029]]
567 +
568 +**Connection:**
569 +
570 +[[image:image-20230512180718-8.png||height="538" width="647"]]
571 +
562 562  **Example**:
563 563  
564 564  If payload is: 0105H:  (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree
... ... @@ -568,195 +568,211 @@
568 568  （FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）
569 569  
570 570  
571 -==== (% style="color:#4472c4" %)**Humidity**(%%) ====
581 +==== 2.3.3.3 Digital Input ====
572 572  
583 +The digital input for pin PB15,
573 573  
574 -Read:0x(0197)=412    Value:  412 / 10=41.2, So 41.2%
585 +* When PB15 is high, the bit 1 of payload byte 6 is 1.
586 +* When PB15 is low, the bit 1 of payload byte 6 is 0.
575 575  
588 +(% class="wikigeneratedid" id="H2.3.3.4A0AnalogueDigitalConverter28ADC29" %)
589 +(((
590 +Note:The maximum voltage input supports 3.6V.
591 +)))
576 576  
577 -==== (% style="color:#4472c4" %)**Alarm Flag& MOD**(%%) ====
593 +(% class="wikigeneratedid" %)
594 +==== 2.3.3.4  Analogue Digital Converter (ADC) ====
578 578  
596 +The measuring range of the node is only about 0.1V to 1.1V The voltage resolution is about 0.24mv.
579 579  
580 -**Example:**
598 +When the measured output voltage of the sensor is not within the range of 0.1V and 1.1V, the output voltage terminal of the sensor shall be divided The example in the following figure is to reduce the output voltage of the sensor by three times If it is necessary to reduce more times, calculate according to the formula in the figure and connect the corresponding resistance in series.
581 581  
582 -If payload & 0x01 = 0x01  **~-~->** This is an Alarm Message
600 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220628150112-1.png?width=285&height=241&rev=1.1||alt="image-20220628150112-1.png" height="241" width="285"]]
583 583  
584 -If payload & 0x01 = 0x00  **~-~->** This is a normal uplink message, no alarm
585 585  
586 -If payload >> 2 = 0x00  **~-~->**  means MOD=1, This is a sampling uplink message
603 +==== 2.3.3.5 Digital Interrupt ====
587 587  
588 -If payload >> 2 = 0x31  **~-~->**  means MOD=31, this message is a reply message for polling, this message contains the alarm settings. see [[this link>>path:#HPolltheAlarmsettings:]] for detail. 
605 +Digital Interrupt refers to pin PB14, and there are different trigger methods. When there is a trigger, the SN50v3 will send a packet to the server.
589 589  
607 +**~ Interrupt connection method:**
590 590  
591 -== 2.4 Payload Decoder file ==
609 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379178634-321.png?rev=1.1||alt="1656379178634-321.png"]]
592 592  
611 +**Example to use with door sensor :**
593 593  
594 -In TTN, use can add a custom payload so it shows friendly reading
613 +The door sensor is shown at right. It is a two wire magnetic contact switch used for detecting the open/close status of doors or windows.
595 595  
596 -In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:
615 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379210849-860.png?rev=1.1||alt="1656379210849-860.png"]]
597 597  
598 -[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B >>https://github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B]]
617 +When the two pieces are close to each other, the 2 wire output will be short or open (depending on the type), while if the two pieces are away from each other, the 2 wire output will be the opposite status. So we can use LSN50 interrupt interface to detect the status for the door or window.
599 599  
619 +**~ Below is the installation example:**
600 600  
601 -== 2.5 Datalog Feature ==
621 +Fix one piece of the magnetic sensor to the door and connect the two pins to LSN50 as follows:
602 602  
623 +* (((
624 +One pin to LSN50's PB14 pin
625 +)))
626 +* (((
627 +The other pin to LSN50's VCC pin
628 +)))
603 603  
604 -Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, S31x-LB will store the reading for future retrieving purposes.
630 +Install the other piece to the door. Find a place where the two pieces will be close to each other when the door is closed. For this particular magnetic sensor, when the door is closed, the output will be short, and PB14 will be at the VCC voltage.
605 605  
632 +Door sensors have two types: ** NC (Normal close)** and **NO (normal open)**. The connection for both type sensors are the same. But the decoding for payload are reverse, user need to modify this in the IoT Server decoder.
606 606  
607 -=== 2.5.1 Ways to get datalog via LoRaWAN ===
634 +When door sensor is shorted, there will extra power consumption in the circuit, the extra current is 3v3/R14 = 3v2/1Mohm = 0.3uA which can be ignored.
608 608  
636 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379283019-229.png?rev=1.1||alt="1656379283019-229.png"]]
609 609  
610 -Set [[PNACKMD=1>>||anchor="H2.5.4DatalogUplinkpayloadA028FPORT3D329"]], S31x-LB will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
638 +The above photos shows the two parts of the magnetic switch fitted to a door.
611 611  
612 -* a) S31x-LB will do an ACK check for data records sending to make sure every data arrive server.
613 -* b) S31x-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB gets a ACK, S31x-LB will consider there is a network connection and resend all NONE-ACK messages.
640 +The software by default uses the falling edge on the signal line as an interrupt. We need to modify it to accept both the rising edge (0v ~-~-> VCC , door close) and the falling edge (VCC ~-~-> 0v , door open) as the interrupt.
614 614  
615 -Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
642 +The command is:
616 616  
617 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="图片-20220703111700-2.png" height="381" width="1119"]]
644 +**AT+INTMOD=1       **~/~/(more info about INMOD please refer** **[[**AT Command Manual**>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/&file=DRAGINO_LSN50_AT_Commands_v1.5.1.pdf]]**. **)
618 618  
619 -=== 2.5.2 Unix TimeStamp ===
646 +Below shows some screen captures in TTN V3:
620 620  
648 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379339508-835.png?rev=1.1||alt="1656379339508-835.png"]]
621 621  
622 -S31x-LB uses Unix TimeStamp format based on
650 +In MOD=1, user can use byte 6 to see the status for door open or close. TTN V3 decoder is as below:
623 623  
624 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
652 +door= (bytes[6] & 0x80)? "CLOSE":"OPEN";
625 625  
626 -User can get this time from link:  [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
627 627  
628 -Below is the converter example
655 +==== 2.3.3.6 I2C Interface (SHT20 & SHT31) ====
629 629  
630 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1||alt="图片-20220523001219-12.png" height="298" width="720"]]
657 +The SDA and SCK are I2C interface lines. You can use these to connect to an I2C device and get the sensor data.
631 631  
632 -So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
659 +We have made an example to show how to use the I2C interface to connect to the SHT20 Temperature and Humidity Sensor.
633 633  
661 +Notice: Different I2C sensors have different I2C commands set and initiate process, if user want to use other I2C sensors, User need to re-write the source code to support those sensors. SHT20 code in SN50_v3 will be a good reference.
634 634  
635 -=== 2.5.3 Set Device Time ===
663 +Below is the connection to SHT20/ SHT31. The connection is as below:
636 636  
665 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220902163605-2.png?rev=1.1||alt="image-20220902163605-2.png"]]
637 637  
638 -User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
667 +The device will be able to get the I2C sensor data now and upload to IoT Server.
639 639  
640 -Once S31x-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to S31x-LB. If S31x-LB fails to get the time from the server, S31x-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
669 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379664142-345.png?rev=1.1||alt="1656379664142-345.png"]]
641 641  
642 -(% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
671 +Convert the read byte to decimal and divide it by ten.
643 643  
673 +**Example:**
644 644  
645 -=== 2.5.4 Datalog Uplink payload (FPORT~=3) ===
675 +Temperature:  Read:0116(H) = 278(D)  Value:  278 /10=27.8℃;
646 646  
677 +Humidity:    Read:0248(H)=584(D)  Value:  584 / 10=58.4, So 58.4%
647 647  
648 -The Datalog uplinks will use below payload format.
679 +If you want to use other I2C device, please refer the SHT20 part source code as reference.
649 649  
650 -**Retrieval data payload:**
651 651  
652 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
653 -|=(% style="width: 80px;background-color:#D9E2F3" %)(((
654 -**Size(bytes)**
655 -)))|=(% style="width: 60px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 60px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 120px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 103px; background-color: rgb(217, 226, 243);" %)**1**|=(% style="width: 85px; background-color: rgb(217, 226, 243);" %)**4**
656 -|(% style="width:103px" %)**Value**|(% style="width:54px" %)(((
657 -[[Temp_Black>>||anchor="HTemperatureBlack:"]]
658 -)))|(% style="width:51px" %)[[Temp_White>>||anchor="HTemperatureWhite:"]]|(% style="width:89px" %)[[Temp_ Red or Temp _White>>||anchor="HTemperatureREDorTemperatureWhite:"]]|(% style="width:103px" %)Poll message flag & Ext|(% style="width:54px" %)[[Unix Time Stamp>>||anchor="H2.5.2UnixTimeStamp"]]
682 +==== 2.3.3.7  ​Distance Reading ====
659 659  
660 -**Poll message flag & Ext:**
684 +Refer [[Ultrasonic Sensor section>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.8UltrasonicSensor]].
661 661  
662 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20221006192726-1.png?width=754&height=112&rev=1.1||alt="图片-20221006192726-1.png" height="112" width="754"]]
663 663  
664 -**No ACK Message**:  1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for **PNACKMD=1** feature)
687 +==== 2.3.3.8 Ultrasonic Sensor ====
665 665  
666 -**Poll Message Flag**: 1: This message is a poll message reply.
689 +This Fundamental Principles of this sensor can be found at this link: [[https:~~/~~/wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU~~_~~__SEN0208>>url:https://wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU___SEN0208]]
667 667  
668 -* Poll Message Flag is set to 1.
691 +The LSN50 detects the pulse width of the sensor and converts it to mm output. The accuracy will be within 1 centimeter. The usable range (the distance between the ultrasonic probe and the measured object) is between 24cm and 600cm.
669 669  
670 -* Each data entry is 11 bytes, to save airtime and battery, devices will send max bytes according to the current DR and Frequency bands.
693 +The picture below shows the connection:
671 671  
672 -For example, in US915 band, the max payload for different DR is:
673 673  
674 -**a) DR0:** max is 11 bytes so one entry of data
696 +Connect to the LSN50 and run **AT+MOD=2** to switch to ultrasonic mode (ULT).
675 675  
676 -**b) DR1:** max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
698 +The ultrasonic sensor uses the 8^^th^^ and 9^^th^^ byte for the measurement value.
677 677  
678 -**c) DR2:** total payload includes 11 entries of data
700 +**Example:**
679 679  
680 -**d) DR3: **total payload includes 22 entries of data.
702 +Distance:  Read: 0C2D(Hex) = 3117(D)  Value:  3117 mm=311.7 cm
681 681  
682 -If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0   
704 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656384895430-327.png?rev=1.1||alt="1656384895430-327.png"]]
683 683  
706 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656384913616-455.png?rev=1.1||alt="1656384913616-455.png"]]
684 684  
685 -**Example:**
708 +You can see the serial output in ULT mode as below:
686 686  
687 -If S31x-LB has below data inside Flash:
710 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656384939855-223.png?rev=1.1||alt="1656384939855-223.png"]]
688 688  
689 -[[image:1682646494051-944.png]]
712 +**In TTN V3 server:**
690 690  
691 -If user sends below downlink command: 3160065F9760066DA705
714 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656384961830-307.png?rev=1.1||alt="1656384961830-307.png"]]
692 692  
693 -Where : Start time: 60065F97 = time 21/1/19 04:27:03
716 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656384973646-598.png?rev=1.1||alt="1656384973646-598.png"]]
694 694  
695 - Stop time: 60066DA7= time 21/1/19 05:27:03
718 +==== 2.3.3.9  Battery Output - BAT pin ====
696 696  
720 +The BAT pin of SN50v3 is connected to the Battery directly. If users want to use BAT pin to power an external sensor. User need to make sure the external sensor is of low power consumption. Because the BAT pin is always open. If the external sensor is of high power consumption. the battery of SN50v3-LB will run out very soon.
697 697  
698 -**S31x-LB will uplink this payload.**
699 699  
700 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-13.png?width=727&height=421&rev=1.1||alt="图片-20220523001219-13.png" height="421" width="727"]]
723 +==== 2.3.3.10  +5V Output ====
701 701  
702 -(((
703 -__**7FFF089801464160065F97**__ **__7FFF__ __088E__ __014B__ __41__ __60066009__** 7FFF0885014E41600660667FFF0875015141600662BE7FFF086B015541600665167FFF08660155416006676E7FFF085F015A41600669C67FFF0857015D4160066C1E
704 -)))
725 +SN50v3 will enable +5V output before all sampling and disable the +5v after all sampling. 
705 705  
706 -(((
707 -Where the first 11 bytes is for the first entry:
708 -)))
727 +The 5V output time can be controlled by AT Command.
709 709  
710 -(((
711 -7FFF089801464160065F97
712 -)))
729 +**AT+5VT=1000**
713 713  
714 -(((
715 -**Ext sensor data**=0x7FFF/100=327.67
716 -)))
731 +Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.
717 717  
718 -(((
719 -**Temp**=0x088E/100=22.00
720 -)))
733 +By default the AT+5VT=500. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.
721 721  
722 -(((
723 -**Hum**=0x014B/10=32.6
724 -)))
725 725  
726 -(((
727 -**poll message flag & Ext**=0x41,means reply data,Ext=1
728 -)))
729 729  
730 -(((
731 -**Unix time** is 0x60066009=1611030423s=21/1/19 04:27:03
732 -)))
737 +==== 2.3.3.11  BH1750 Illumination Sensor ====
733 733  
739 +MOD=1 support this sensor. The sensor value is in the 8^^th^^ and 9^^th^^ bytes.
734 734  
735 -(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的
741 +[[image:image-20230512172447-4.png||height="593" width="1015"]]
736 736  
737 -== 2.6 Temperature Alarm Feature ==
743 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220628110012-12.png?rev=1.1||alt="image-20220628110012-12.png"]]
738 738  
739 739  
740 -S31x-LB work flow with Alarm feature.
746 +==== 2.3.3.12  Working MOD ====
741 741  
748 +The working MOD info is contained in the Digital in & Digital Interrupt byte (7^^th^^ Byte).
742 742  
743 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-D20-D22-D23%20LoRaWAN%20Temperature%20Sensor%20User%20Manual/WebHome/image-20220623090437-1.png?rev=1.1||alt="图片-20220623090437-1.png"]]
750 +User can use the 3^^rd^^ ~~ 7^^th^^  bit of this byte to see the working mod:
744 744  
752 +Case 7^^th^^ Byte >> 2 & 0x1f:
745 745  
746 -== 2.7 Frequency Plans ==
754 +* 0: MOD1
755 +* 1: MOD2
756 +* 2: MOD3
757 +* 3: MOD4
758 +* 4: MOD5
759 +* 5: MOD6
747 747  
761 +== 2.4 Payload Decoder file ==
748 748  
749 -The S31x-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
750 750  
764 +In TTN, use can add a custom payload so it shows friendly reading
765 +
766 +In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:
767 +
768 +[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B >>https://github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B]]
769 +
770 +
771 +
772 +== 2.5 Frequency Plans ==
773 +
774 +
775 +The SN50v3-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
776 +
751 751  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
752 752  
753 753  
754 -= 3. Configure S31x-LB =
780 += 3. Configure SN50v3-LB =
755 755  
756 756  == 3.1 Configure Methods ==
757 757  
758 758  
759 -S31x-LB supports below configure method:
785 +SN50v3-LB supports below configure method:
760 760  
761 761  * AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
762 762  * AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
... ... @@ -775,7 +775,7 @@
775 775  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
776 776  
777 777  
778 -== 3.3 Commands special design for S31x-LB ==
804 +== 3.3 Commands special design for SN50v3-LB ==
779 779  
780 780  
781 781  These commands only valid for S31x-LB, as below:
... ... @@ -811,7 +811,6 @@
811 811  
812 812  === 3.3.2 Get Device Status ===
813 813  
814 -
815 815  Send a LoRaWAN downlink to ask device send Alarm settings.
816 816  
817 817  (% style="color:blue" %)**Downlink Payload:  **(%%)0x26 01
... ... @@ -819,77 +819,6 @@
819 819  Sensor will upload Device Status via FPORT=5. See payload section for detail.
820 820  
821 821  
822 -=== 3.3.3 Set Temperature Alarm Threshold ===
823 -
824 -* (% style="color:blue" %)**AT Command:**
825 -
826 -(% style="color:#037691" %)**AT+SHTEMP=min,max**
827 -
828 -* When min=0, and max≠0, Alarm higher than max
829 -* When min≠0, and max=0, Alarm lower than min
830 -* When min≠0 and max≠0, Alarm higher than max or lower than min
831 -
832 -Example:
833 -
834 - AT+SHTEMP=0,30   ~/~/ Alarm when temperature higher than 30.
835 -
836 -* (% style="color:blue" %)**Downlink Payload:**
837 -
838 -(% style="color:#037691" %)**0x(0C 01 00 1E)**  (%%) ~/~/ Set AT+SHTEMP=0,30
839 -
840 -(% style="color:red" %)**(note: 3^^rd^^ byte= 0x00 for low limit(not set), 4^^th^^ byte = 0x1E for high limit: 30)**
841 -
842 -
843 -=== 3.3.4 Set Humidity Alarm Threshold ===
844 -
845 -* (% style="color:blue" %)**AT Command:**
846 -
847 -(% style="color:#037691" %)**AT+SHHUM=min,max**
848 -
849 -* When min=0, and max≠0, Alarm higher than max
850 -* When min≠0, and max=0, Alarm lower than min
851 -* When min≠0 and max≠0, Alarm higher than max or lower than min
852 -
853 -Example:
854 -
855 - AT+SHHUM=70,0  ~/~/ Alarm when humidity lower than 70%.
856 -
857 -* (% style="color:blue" %)**Downlink Payload:**
858 -
859 -(% style="color:#037691" %)**0x(0C 02 46 00)**(%%)  ~/~/ Set AT+SHTHUM=70,0
860 -
861 -(% style="color:red" %)**(note: 3^^rd^^ byte= 0x46 for low limit (70%), 4^^th^^ byte = 0x00 for high limit (not set))**
862 -
863 -
864 -=== 3.3.5 Set Alarm Interval ===
865 -
866 -The shortest time of two Alarm packet. (unit: min)
867 -
868 -* (% style="color:blue" %)**AT Command:**
869 -
870 -(% style="color:#037691" %)**AT+ATDC=30** (%%) ~/~/ The shortest interval of two Alarm packets is 30 minutes, Means is there is an alarm packet uplink, there won't be another one in the next 30 minutes.
871 -
872 -* (% style="color:blue" %)**Downlink Payload:**
873 -
874 -(% style="color:#037691" %)**0x(0D 00 1E)**(%%)     **~-~--> ** Set AT+ATDC=0x 00 1E = 30 minutes
875 -
876 -
877 -=== 3.3.6 Get Alarm settings ===
878 -
879 -
880 -Send a LoRaWAN downlink to ask device send Alarm settings.
881 -
882 -* (% style="color:#037691" %)**Downlink Payload:  **(%%)0x0E 01
883 -
884 -**Example:**
885 -
886 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-D20-D22-D23%20LoRaWAN%20Temperature%20Sensor%20User%20Manual/WebHome/1655948182791-225.png?rev=1.1||alt="1655948182791-225.png"]]
887 -
888 -
889 -**Explain:**
890 -
891 -* Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.
892 -
893 893  === 3.3.7 Set Interrupt Mode ===
894 894  
895 895  
... ... @@ -949,8 +949,12 @@
949 949  
950 950  = 6. FAQ =
951 951  
906 +== 6.1 Where can i find source code of SN50v3-LB? ==
952 952  
908 +* **[[Hardware Source Files>>https://github.com/dragino/Lora/tree/master/LSN50/v3.0]].**
909 +* **[[Software Source Code & Compile instruction>>https://github.com/dragino/SN50v3]].**
953 953  
911 +
954 954  = 7. Order Info =
955 955  
956 956  
image-20230512163509-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +1.5 MB
Content
image-20230512164658-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.0 MB
Content
image-20230512170701-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.5 MB
Content
image-20230512172447-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.0 MB
Content
image-20230512173758-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.1 MB
Content
image-20230512173903-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.3 MB
Content
image-20230512180609-7.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.3 MB
Content
image-20230512180718-8.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.3 MB
Content
image-20230512181814-9.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +2.2 MB
Content
image-20230513084523-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Saxer
Size
... ... @@ -1,0 +1,1 @@
1 +611.3 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0