S31-LB / S31B-LB LoRaWAN Outdoor Temperature & Humidity Sensor User Manual

The Dragino S31x-LB is a **LoRaWAN Temperature and Humidity Sensor** for Internet of Things solution. It is used to measure the **surrounding environment temperature and relative air humidity precisely**, and then upload to IoT server via LoRaWAN wireless protocol.

21

22

The temperature & humidity sensor used in S31x-LB is SHT31, which is fully calibrated, linearized, and temperature compensated digital output from Sensirion, it provides a strong reliability and long-term stability. The SHT31 is fixed in a **waterproof anti-condensation casing** for long term use.

23

24

The LoRa wireless technology used in S31x-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.

25

26

S31x-LB supports **Temperature & Humdity alarm feature,** user can set temperature alarm for instant notice. S31x-LB supports Datalog feature, it can save the data when there is no LoRaWAN network and uplink when network recover.

27

28

S31x-LB has max 3 probes which measure maximum 3 temperature points.

29

30

S31x-LB **supports BLE configure** and **wireless OTA update** which make user easy to use.

31

32

S31x-LB is powered by **8500mAh Li-SOCI2 battery**, it is designed for long term use up to 5 years.

33

34

Each S31x-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.

== 1.2 Features ==

* LoRaWAN 1.0.3 Class A

40

* Ultra-low power consumption

41

* External 3 meters SHT31 probe (For S31-LB)

42

* Measure range -55°C ~~ 125°C

43

* Temperature & Humidity alarm

44

* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865

45

* Support Bluetooth v5.1 and LoRaWAN remote configure

46

* Support wireless OTA update firmware

47

* Uplink on periodically

48

* Downlink to change configure

49

* 8500mAh Battery for long term use

50

51

== 1.3 Specification ==

52

53

54

(% style="color:#037691" %)**Common DC Characteristics:**

55

56

* Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v

57

* Operating Temperature: -40 ~~ 85°C

58

59

(% style="color:#037691" %)**Temperature Sensor:**

60

61

* Range: -40 to + 80°C

62

* Accuracy: ±0.2 @ 0-90 °C

63

* Resolution: 0.1°C

64

* Long Term Shift: <0.03 °C/yr

65

66

(% style="color:#037691" %)**Humidity Sensor: **

67

68

* Range: 0 ~~ 99.9% RH

69

* Accuracy: ± 2%RH ( 0 ~~ 100%RH)

70

* Resolution: 0.01% RH

71

* Long Term Shift: <0.25 %RH/yr

72

73

(% style="color:#037691" %)**LoRa Spec:**

74

75

* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz

76

* Max +22 dBm constant RF output vs.

77

* RX sensitivity: down to -139 dBm.

78

* Excellent blocking immunity

79

80

(% style="color:#037691" %)**Battery:**

81

82

* Li/SOCI2 un-chargeable battery

83

* Capacity: 8500mAh

84

* Self-Discharge: <1% / Year @ 25°C

85

* Max continuously current: 130mA

86

* Max boost current: 2A, 1 second

87

88

(% style="color:#037691" %)**Power Consumption**

89

90

* Sleep Mode: 5uA @ 3.3v

91

* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm

92

93

== 1.4 Sleep mode and working mode ==

94

95

96

(% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.

97

98

(% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.

99

100

101

== 1.5 Button & LEDs ==

102

103

104

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]

105

106

107

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

108

|=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)**Action**

109

|(% style="width:167px" %)Pressing ACT between 1s < time < 3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((

110

If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.

111

Meanwhile, BLE module will be active and user can connect via BLE to configure device.

112

)))

113

|(% style="width:167px" %)Pressing ACT for more than 3s|(% style="width:117px" %)Active Device|(% style="width:225px" %)(((

114

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.

115

(% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

116

Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.

117

)))

118

|(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.

119

120

== 1.6 BLE connection ==

121

122

123

S31x-LB support BLE remote configure.

124

125

126

BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:

127

128

* Press button to send an uplink

129

* Press button to active device.

130

* Device Power on or reset.

131

132

If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.

133

134

135

== 1.7 Hardware Variant ==

136

137

138

(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)

139

|=(% style="width: 102px;background-color:#D9E2F3;color:#0070C0" %)Model|=(% style="width: 190px;background-color:#D9E2F3;color:#0070C0" %)Photo|=(% style="width: 218px;background-color:#D9E2F3;color:#0070C0" %)Probe Info

140

|(% style="width:102px" %)S31-LB|(% style="width:190px" %) |(% style="width:297px" %)(((

141

1 x SHT31 Probe

142

143

Cable Length : 2 meters

)))

|(% style="width:102px" %)S31B-LB|(% style="width:190px" %) |(% style="width:297px" %)(((

1 x SHT31 Probe

Installed in device.

)))

(% style="display:none" %)

== 1.8 Mechanical ==

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]

161

162

163

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]

164

165

166

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]

167

168

169

= 2. Configure S31x-LB to connect to LoRaWAN network =

170

171

== 2.1 How it works ==

172

173

174

The S31x-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.

175

176

177

== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==

178

179

180

Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.

181

182

The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.

183

184

185

(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from S31x-LB.

186

187

Each S31x-LB is shipped with a sticker with the default device EUI as below:

188

189

[[image:image-20230426084152-1.png||alt="图片-20230426084152-1.png" height="233" width="502"]]

190

191

192

You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:

193

194

195

(% style="color:blue" %)**Register the device**

196

197

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/1654935135620-998.png?rev=1.1||alt="1654935135620-998.png"]]

198

199

200

(% style="color:blue" %)**Add APP EUI and DEV EUI**

201

202

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-4.png?width=753&height=551&rev=1.1||alt="图片-20220611161308-4.png"]]

203

204

205

(% style="color:blue" %)**Add APP EUI in the application**

206

207

208

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-5.png?width=742&height=601&rev=1.1||alt="图片-20220611161308-5.png"]]

209

210

211

(% style="color:blue" %)**Add APP KEY**

212

213

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]

214

215

216

(% style="color:blue" %)**Step 2:**(%%) Activate on S31x-LB

217

218

219

Press the button for 5 seconds to activate the S31x-LB.

220

221

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

222

223

After join success, it will start to upload messages to TTN and you can see the messages in the panel.

224

225

226

== 2.3 Uplink Payload ==

227

228

=== 2.3.1 Device Status, FPORT~=5 ===

229

230

231

Users can use the downlink command(**0x26 01**) to ask S31x-LB to send device configure detail, include device configure status. S31x-LB will uplink a payload via FPort=5 to server.

232

233

The Payload format is as below.

234

235

236

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

237

|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**

Example parse in TTNv3

242

243

[[image:image-20230421171614-1.png||alt="图片-20230421171614-1.png"]]

244

245

246

(% style="color:#037691" %)**Sensor Model**(%%): For S31x-LB, this value is 0x0A

247

248

(% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version

249

250

(% style="color:#037691" %)**Frequency Band**:

*0x01: EU868

*0x02: US915

*0x03: IN865

*0x04: AU915

*0x05: KZ865

*0x06: RU864

*0x07: AS923

*0x08: AS923-1

*0x09: AS923-2

*0x0a: AS923-3

*0x0b: CN470

*0x0c: EU433

*0x0d: KR920

*0x0e: MA869

(% style="color:#037691" %)**Sub-Band**:

282

283

AU915 and US915:value 0x00 ~~ 0x08

284

285

CN470: value 0x0B ~~ 0x0C

286

287

Other Bands: Always 0x00

288

289

290

(% style="color:#037691" %)**Battery Info**:

291

292

Check the battery voltage.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

=== 2.3.2 Sensor Data. FPORT~=2 ===

300

301

302

Sensor Data is uplink via FPORT=2

303

304

(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)

305

|=(% style="width: 90px;background-color:#D9E2F3" %)(((

306

**Size(bytes)**

307

)))|=(% style="width: 80px;background-color:#D9E2F3" %)2|=(% style="width: 90px;background-color:#D9E2F3" %)4|=(% style="width:80px;background-color:#D9E2F3" %)1|=(% style="width: 80px;background-color:#D9E2F3" %)**2**|=(% style="width: 80px;background-color:#D9E2F3" %)2

308

|(% style="width:99px" %)**Value**|(% style="width:69px" %)(((

309

[[Battery>>||anchor="HBattery:"]]

310

)))|(% style="width:130px" %)(((

311

[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]

312

)))|(% style="width:91px" %)(((

313

[[Alarm Flag>>||anchor="HAlarmFlag26MOD:"]]

314

)))|(% style="width:103px" %)(((

315

[[Temperature>>||anchor="HTemperature:"]]

316

)))|(% style="width:80px" %)(((

317

[[Humidity>>||anchor="HHumidity:"]]

318

)))

319

320

==== (% style="color:#4472c4" %)**Battery**(%%) ====

321

322

Sensor Battery Level.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

==== (% style="color:#4472c4" %)**Temperature**(%%) ====

**Example**:

If payload is: 0105H: (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree

335

336

If payload is: FF3FH : (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.

337

338

（FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）

339

340

341

==== (% style="color:#4472c4" %)**Humidity**(%%) ====

342

343

344

Read:0x(0197)=412 Value: 412 / 10=41.2, So 41.2%

345

346

347

==== (% style="color:#4472c4" %)**Alarm Flag& MOD**(%%) ====

**Example:**

If payload & 0x01 = 0x01 **~-~->** This is an Alarm Message

353

354

If payload & 0x01 = 0x00 **~-~->** This is a normal uplink message, no alarm

355

356

If payload >> 2 = 0x00 **~-~->** means MOD=1, This is a sampling uplink message

357

358

If payload >> 2 = 0x31 **~-~->** means MOD=31, this message is a reply message for polling, this message contains the alarm settings. see [[this link>>path:#HPolltheAlarmsettings:]] for detail.

359

360

361

== 2.4 Payload Decoder file ==

362

363

364

In TTN, use can add a custom payload so it shows friendly reading

365

366

In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:

367

368

[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B >>https://github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B]]

369

370

371

== 2.5 Datalog Feature ==

372

373

374

Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, S31x-LB will store the reading for future retrieving purposes.

375

376

377

=== 2.5.1 Ways to get datalog via LoRaWAN ===

378

379

380

Set [[PNACKMD=1>>||anchor="H2.5.4DatalogUplinkpayloadA028FPORT3D329"]], S31x-LB will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.

381

382

* a) S31x-LB will do an ACK check for data records sending to make sure every data arrive server.

383

* b) S31x-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB gets a ACK, S31x-LB will consider there is a network connection and resend all NONE-ACK messages.

384

385

Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)

386

387

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="图片-20220703111700-2.png" height="381" width="1119"]]

388

389

=== 2.5.2 Unix TimeStamp ===

390

391

392

S31x-LB uses Unix TimeStamp format based on

393

394

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]

395

396

User can get this time from link: [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :

397

398

Below is the converter example

399

400

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1||alt="图片-20220523001219-12.png" height="298" width="720"]]

401

402

So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25

403

404

405

=== 2.5.3 Set Device Time ===

406

407

408

User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.

409

410

Once S31x-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to S31x-LB. If S31x-LB fails to get the time from the server, S31x-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).

411

412

(% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**

413

414

415

=== 2.5.4 Datalog Uplink payload (FPORT~=3) ===

416

417

418

The Datalog uplinks will use below payload format.

419

420

**Retrieval data payload:**

421

422

(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)

423

|=(% style="width: 80px;background-color:#D9E2F3" %)(((

424

**Size(bytes)**

425

)))|=(% style="width: 60px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 60px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 120px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 103px; background-color: rgb(217, 226, 243);" %)**1**|=(% style="width: 85px; background-color: rgb(217, 226, 243);" %)**4**

426

|(% style="width:103px" %)**Value**|(% style="width:54px" %)(((

427

[[Temp_Black>>||anchor="HTemperatureBlack:"]]

428

)))|(% style="width:51px" %)[[Temp_White>>||anchor="HTemperatureWhite:"]]|(% style="width:89px" %)[[Temp_ Red or Temp _White>>||anchor="HTemperatureREDorTemperatureWhite:"]]|(% style="width:103px" %)Poll message flag & Ext|(% style="width:54px" %)[[Unix Time Stamp>>||anchor="H2.5.2UnixTimeStamp"]]

429

430

**Poll message flag & Ext:**

431

432

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20221006192726-1.png?width=754&height=112&rev=1.1||alt="图片-20221006192726-1.png" height="112" width="754"]]

433

434

**No ACK Message**: 1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for **PNACKMD=1** feature)

435

436

**Poll Message Flag**: 1: This message is a poll message reply.

437

438

* Poll Message Flag is set to 1.

439

440

* Each data entry is 11 bytes, to save airtime and battery, devices will send max bytes according to the current DR and Frequency bands.

441

442

For example, in US915 band, the max payload for different DR is:

443

444

**a) DR0:** max is 11 bytes so one entry of data

445

446

**b) DR1:** max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)

447

448

**c) DR2:** total payload includes 11 entries of data

449

450

**d) DR3: **total payload includes 22 entries of data.

451

452

If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0

**Example:**

If S31x-LB has below data inside Flash:

458

459

[[image:1682646494051-944.png]]

460

461

If user sends below downlink command: 3160065F9760066DA705

462

463

Where : Start time: 60065F97 = time 21/1/19 04:27:03

464

465

Stop time: 60066DA7= time 21/1/19 05:27:03

466

467

468

**S31x-LB will uplink this payload.**

469

470

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-13.png?width=727&height=421&rev=1.1||alt="图片-20220523001219-13.png" height="421" width="727"]]

471

472

(((

473

__**7FFF089801464160065F97**__ **__7FFF__ __088E__ __014B__ __41__ __60066009__** 7FFF0885014E41600660667FFF0875015141600662BE7FFF086B015541600665167FFF08660155416006676E7FFF085F015A41600669C67FFF0857015D4160066C1E

)))

(((

Where the first 11 bytes is for the first entry:

)))

(((

7FFF089801464160065F97

)))

(((

**Ext sensor data**=0x7FFF/100=327.67

)))

(((

**Temp**=0x088E/100=22.00

)))

(((

**Hum**=0x014B/10=32.6

)))

(((

**poll message flag & Ext**=0x41,means reply data,Ext=1

)))

(((

**Unix time** is 0x60066009=1611030423s=21/1/19 04:27:03

)))

(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的

506

507

== 2.6 Temperature Alarm Feature ==

508

509

510

S31x-LB work flow with Alarm feature.

511

512

513

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-D20-D22-D23%20LoRaWAN%20Temperature%20Sensor%20User%20Manual/WebHome/image-20220623090437-1.png?rev=1.1||alt="图片-20220623090437-1.png"]]

514

515

516

== 2.7 Frequency Plans ==

517

518

519

The S31x-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.

520

521

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]

522

523

524

= 3. Configure S31x-LB =

525

526

== 3.1 Configure Methods ==

527

528

529

S31x-LB supports below configure method:

530

531

* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].

532

* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].

533

* LoRaWAN Downlink. Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.

534

535

== 3.2 General Commands ==

536

537

538

These commands are to configure:

539

540

* General system settings like: uplink interval.

541

* LoRaWAN protocol & radio related command.

542

543

They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:

544

545

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]

546

547

548

== 3.3 Commands special design for S31x-LB ==

549

550

551

These commands only valid for S31x-LB, as below:

552

553

554

=== 3.3.1 Set Transmit Interval Time ===

555

556

557

Feature: Change LoRaWAN End Node Transmit Interval.

558

559

(% style="color:blue" %)**AT Command: AT+TDC**

560

561

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

562

|=(% style="width: 156px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3" %)**Function**|=(% style="background-color:#D9E2F3" %)**Response**

563

|(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((

564

30000

565

OK

566

the interval is 30000ms = 30s

567

)))

568

|(% style="width:156px" %)AT+TDC=60000|(% style="width:137px" %)Set Transmit Interval|(((

569

OK

570

Set transmit interval to 60000ms = 60 seconds

571

)))

572

573

(% style="color:blue" %)**Downlink Command: 0x01**

574

575

Format: Command Code (0x01) followed by 3 bytes time value.

576

577

If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.

578

579

* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds

580

* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds

581

582

=== 3.3.2 Get Device Status ===

583

584

585

Send a LoRaWAN downlink to ask device send Alarm settings.

586

587

(% style="color:blue" %)**Downlink Payload: **(%%)0x26 01

588

589

Sensor will upload Device Status via FPORT=5. See payload section for detail.

590

591

592

=== 3.3.3 Set Temperature Alarm Threshold ===

593

594

* (% style="color:blue" %)**AT Command:**

595

596

(% style="color:#037691" %)**AT+SHTEMP=min,max**

597

598

* When min=0, and max≠0, Alarm higher than max

599

* When min≠0, and max=0, Alarm lower than min

600

* When min≠0 and max≠0, Alarm higher than max or lower than min

Example:

AT+SHTEMP=0,30 ~/~/ Alarm when temperature higher than 30.

605

606

* (% style="color:blue" %)**Downlink Payload:**

607

608

(% style="color:#037691" %)**0x(0C 01 00 1E)** (%%) ~/~/ Set AT+SHTEMP=0,30

609

610

(% style="color:red" %)**(note: 3^^rd^^ byte= 0x00 for low limit(not set), 4^^th^^ byte = 0x1E for high limit: 30)**

611

612

613

=== 3.3.4 Set Humidity Alarm Threshold ===

614

615

* (% style="color:blue" %)**AT Command:**

616

617

(% style="color:#037691" %)**AT+SHHUM=min,max**

618

619

* When min=0, and max≠0, Alarm higher than max

620

* When min≠0, and max=0, Alarm lower than min

621

* When min≠0 and max≠0, Alarm higher than max or lower than min

Example:

AT+SHHUM=70,0 ~/~/ Alarm when humidity lower than 70%.

626

627

* (% style="color:blue" %)**Downlink Payload:**

628

629

(% style="color:#037691" %)**0x(0C 02 46 00)**(%%) ~/~/ Set AT+SHTHUM=70,0

630

631

(% style="color:red" %)**(note: 3^^rd^^ byte= 0x46 for low limit (70%), 4^^th^^ byte = 0x00 for high limit (not set))**

632

633

634

=== 3.3.5 Set Alarm Interval ===

635

636

The shortest time of two Alarm packet. (unit: min)

637

638

* (% style="color:blue" %)**AT Command:**

639

640

(% style="color:#037691" %)**AT+ATDC=30** (%%) ~/~/ The shortest interval of two Alarm packets is 30 minutes, Means is there is an alarm packet uplink, there won't be another one in the next 30 minutes.

641

642

* (% style="color:blue" %)**Downlink Payload:**

643

644

(% style="color:#037691" %)**0x(0D 00 1E)**(%%) **~-~--> ** Set AT+ATDC=0x 00 1E = 30 minutes

645

646

647

=== 3.3.6 Get Alarm settings ===

648

649

650

Send a LoRaWAN downlink to ask device send Alarm settings.

651

652

* (% style="color:#037691" %)**Downlink Payload: **(%%)0x0E 01

**Example:**

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-D20-D22-D23%20LoRaWAN%20Temperature%20Sensor%20User%20Manual/WebHome/1655948182791-225.png?rev=1.1||alt="1655948182791-225.png"]]

**Explain:**

* Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.

662

663

=== 3.3.7 Set Interrupt Mode ===

664

665

666

Feature, Set Interrupt mode for GPIO_EXIT.

667

668

(% style="color:blue" %)**AT Command: AT+INTMOD**

669

670

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

671

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

672

|(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((

673

0

674

OK

675

the mode is 0 =Disable Interrupt

676

)))

677

|(% style="width:154px" %)AT+INTMOD=2|(% style="width:196px" %)(((

678

Set Transmit Interval

679

0. (Disable Interrupt),

680

~1. (Trigger by rising and falling edge)

681

2. (Trigger by falling edge)

682

3. (Trigger by rising edge)

683

)))|(% style="width:157px" %)OK

684

685

(% style="color:blue" %)**Downlink Command: 0x06**

686

687

Format: Command Code (0x06) followed by 3 bytes.

688

689

This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.

690

691

* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode

692

* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger

693

694

= 4. Battery & Power Consumption =

695

696

697

S31x-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.

698

699

[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .

700

701

702

= 5. OTA Firmware update =

703

704

705

(% class="wikigeneratedid" %)

706

User can change firmware S31x-LB to:

707

708

* Change Frequency band/ region.

709

* Update with new features.

710

* Fix bugs.

711

712

Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]**

713

714

715

Methods to Update Firmware:

716

717

* (Recommanded way) OTA firmware update via wireless: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]

718

* Update through UART TTL interface.**[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.

= 6. FAQ =

= 7. Order Info =

Part Number: **S31-LB-XX / S31B-LB-XX**

728

729

**XX**: The default frequency band

730

731

* **AS923**: LoRaWAN AS923 band

732

733

* **AU915**: LoRaWAN AU915 band

734

735

* **EU433**: LoRaWAN EU433 band

736

737

* **EU868**: LoRaWAN EU868 band

738

739

* **KR920**: LoRaWAN KR920 band

740

741

* **US915**: LoRaWAN US915 band

742

743

* **IN865**: LoRaWAN IN865 band

744

745

* **CN470**: LoRaWAN CN470 band

= =

= 8. Packing Info =

**Package Includes**:

752

753

* S31x-LB LoRaWAN Temperature & Humidity Sensor

754

755

**Dimension and weight**:

* Device Size: cm

* Device Weight: g

* Package Size / pcs : cm

* Weight / pcs : g

= 9. Support =

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

769

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]

Wiki source code of S31-LB / S31B-LB LoRaWAN Outdoor Temperature & Humidity Sensor User Manual

Applications

Navigation