RS485-LN – RS485 to LoRaWAN Converter

The Dragino RS485-LN is a (% style="color:blue" %)**RS485 to LoRaWAN Converter**(%%). It converts the RS485 signal into LoRaWAN wireless signal which simplify the IoT installation and reduce the installation/maintaining cost.

22

)))

23

24

(((

25

RS485-LN allows user to (% style="color:blue" %)**monitor / control RS485 devices**(%%) and reach extremely long ranges. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption. It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on.

)))

(((

(% style="color:blue" %)**For data uplink**(%%), RS485-LN sends user-defined commands to RS485 devices and gets the return from the RS485 devices. RS485-LN will process these returns according to user-define rules to get the final payload and upload to LoRaWAN server.

)))

(((

(% style="color:blue" %)**For data downlink**(%%), RS485-LN runs in LoRaWAN Class C. When there downlink commands from LoRaWAN server, RS485-LN will forward the commands from LoRaWAN server to RS485 devices.

34

35

(% style="color:blue" %)**Demo Dashboard for RS485-LN**(%%) connect to two energy meters: [[https:~~/~~/app.datacake.de/dashboard/d/58844a26-378d-4c5a-aaf5-b5b5b153447a>>url:https://app.datacake.de/dashboard/d/58844a26-378d-4c5a-aaf5-b5b5b153447a]]

)))

)))

[[image:1653267211009-519.png||height="419" width="724"]]

40

41

42

== 1.2 Specifications ==

**Hardware System:**

* STM32L072CZT6 MCU

* SX1276/78 Wireless Chip

49

* Power Consumption (exclude RS485 device):

50

** Idle: 32mA@12v

51

** 20dB Transmit: 65mA@12v

52

53

**Interface for Model:**

54

55

* RS485

56

* Power Input 7~~ 24V DC.

**LoRa Spec:**

* Frequency Range:

** Band 1 (HF): 862 ~~ 1020 Mhz

62

** Band 2 (LF): 410 ~~ 528 Mhz

63

* 168 dB maximum link budget.

64

* +20 dBm - 100 mW constant RF output vs.

65

* +14 dBm high efficiency PA.

66

* Programmable bit rate up to 300 kbps.

67

* High sensitivity: down to -148 dBm.

68

* Bullet-proof front end: IIP3 = -12.5 dBm.

69

* Excellent blocking immunity.

70

* Low RX current of 10.3 mA, 200 nA register retention.

71

* Fully integrated synthesizer with a resolution of 61 Hz.

72

* FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.

73

* Built-in bit synchronizer for clock recovery.

74

* Preamble detection.

75

* 127 dB Dynamic Range RSSI.

76

* Automatic RF Sense and CAD with ultra-fast AFC.

77

* Packet engine up to 256 bytes with CRC.

== 1.3 Features ==

* LoRaWAN Class A & Class C protocol (default Class C)

83

* Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865/RU864

84

* AT Commands to change parameters

85

* Remote configure parameters via LoRa Downlink

86

* Firmware upgradable via program port

87

* Support multiply RS485 devices by flexible rules

88

* Support Modbus protocol

89

* Support Interrupt uplink (Since hardware version v1.2)

90

91

92

== 1.4 Applications ==

93

94

* Smart Buildings & Home Automation

95

* Logistics and Supply Chain Management

* Smart Metering

* Smart Agriculture

* Smart Cities

* Smart Factory

== 1.5 Firmware Change log ==

103

104

[[RS485-LN Image files – Download link and Change log>>url:http://www.dragino.com/downloads/index.php?dir=RS485-LN/]]

105

106

107

== 1.6 Hardware Change log ==

(((

(((

v1.2: Add External Interrupt Pin.

v1.0: Release

)))

)))

= 2. Power ON Device =

120

121

(((

122

The RS485-LN can be powered by 7 ~~ 24V DC power source. Connection as below

123

124

* Power Source VIN to RS485-LN VIN+

125

* Power Source GND to RS485-LN VIN-

126

127

(((

128

Once there is power, the RS485-LN will be on.

129

)))

130

131

[[image:1653268091319-405.png]]

)))

= 3. Operation Mode =

137

138

== 3.1 How it works? ==

139

140

(((

141

The RS485-LN is configured as LoRaWAN OTAA Class C mode by default. It has OTAA keys to join network. To connect a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the RS485-LN. It will auto join the network via OTAA.

)))

== 3.2 Example to join LoRaWAN network ==

147

148

Here shows an example for how to join the TTN V3 Network. Below is the network structure, we use [[LG308>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/140-lg308.html]] as LoRaWAN gateway here.

149

150

[[image:1653268155545-638.png||height="334" width="724"]]

(((

(((

The RS485-LN in this example connected to two RS485 devices for demonstration, user can connect to other RS485 devices via the same method. The connection is as below:

)))

(((

485A+ and 485B- of the sensor are connected to RS485A and RA485B of RS485-LN respectively.

160

)))

161

162

[[image:1653268227651-549.png||height="592" width="720"]]

163

164

(((

165

The LG308 is already set to connect to [[TTN V3 network >>path:eu1.cloud.thethings.network/]]. So what we need to now is only configure the TTN V3:

)))

(((

**Step 1**: Create a device in TTN V3 with the OTAA keys from RS485-LN.

)))

(((

Each RS485-LN is shipped with a sticker with unique device EUI:

)))

)))

[[image:1652953462722-299.png]]

(((

(((

User can enter this key in their LoRaWAN Server portal. Below is TTN V3 screen shot:

)))

(((

Add APP EUI in the application.

)))

)))

[[image:image-20220519174512-1.png]]

190

191

[[image:image-20220519174512-2.png||height="323" width="720"]]

192

193

[[image:image-20220519174512-3.png||height="556" width="724"]]

194

195

[[image:image-20220519174512-4.png]]

196

197

You can also choose to create the device manually.

198

199

[[image:1652953542269-423.png||height="710" width="723"]]

200

201

Add APP KEY and DEV EUI

202

203

[[image:1652953553383-907.png||height="514" width="724"]]

(((

**Step 2**: Power on RS485-LN and it will auto join to the TTN V3 network. After join success, it will start to upload message to TTN V3 and user can see in the panel.

208

)))

209

210

[[image:1652953568895-172.png||height="232" width="724"]]

211

212

213

== 3.3 Configure Commands to read data ==

(((

(((

There are plenty of RS485 devices in the market and each device has different command to read the valid data. To support these devices in flexible, RS485-LN supports flexible command set. User can use [[AT Commands>>path:#AT_COMMAND]] or LoRaWAN Downlink Command to configure what commands RS485-LN should send for each sampling and how to handle the return from RS485 devices.

)))

(((

(% style="color:red" %)Note: below description and commands are for firmware version >v1.1, if you have firmware version v1.0. Please check the [[user manual v1.0>>url:http://www.dragino.com/downloads/index.php?dir=RS485-LN/&file=RS485-LN_UserManual_v1.0.1.pdf]] or upgrade the firmware to v1.1

)))

)))

=== 3.3.1 onfigure UART settings for RS485 or TTL communication ===

228

229

To use RS485-LN to read data from RS485 sensors, connect the RS485-LN A/B traces to the sensors. And user need to make sure RS485-LN use the match UART setting to access the sensors. The related commands for UART settings are:

230

231

(% border="1" style="background-color:#ffffcc; color:green; width:782px" %)

232

|(% style="width:128px" %)(((

233

**AT Commands**

234

)))|(% style="width:305px" %)(((

235

**Description**

236

)))|(% style="width:346px" %)(((

237

**Example**

238

)))

239

|(% style="width:128px" %)(((

240

AT+BAUDR

241

)))|(% style="width:305px" %)(((

242

Set the baud rate (for RS485 connection). Default Value is: 9600.

243

)))|(% style="width:346px" %)(((

(((

AT+BAUDR=9600

)))

(((

Options: (1200,2400,4800,14400,19200,115200)

250

)))

251

)))

252

|(% style="width:128px" %)(((

253

AT+PARITY

254

)))|(% style="width:305px" %)(((

255

Set UART parity (for RS485 connection)

256

)))|(% style="width:346px" %)(((

(((

AT+PARITY=0

)))

(((

Option: 0: no parity, 1: odd parity, 2: even parity

263

)))

264

)))

265

|(% style="width:128px" %)(((

266

AT+STOPBIT

267

)))|(% style="width:305px" %)(((

268

(((

269

Set serial stopbit (for RS485 connection)

)))

(((

)))

)))|(% style="width:346px" %)(((

276

(((

277

AT+STOPBIT=0 for 1bit

)))

(((

AT+STOPBIT=1 for 1.5 bit

)))

(((

AT+STOPBIT=2 for 2 bits

)))

)))

=== 3.3.2 Configure sensors ===

(((

(((

Some sensors might need to configure before normal operation. User can configure such sensor via PC and RS485 adapter or through RS485-LN AT Commands (% style="color:#4f81bd" %)**AT+CFGDEV**(%%). Each (% style="color:#4f81bd" %)**AT+CFGDEV **(%%)equals to send a RS485 command to sensors. This command will only run when user input it and won’t run during each sampling.

)))

)))

(% border="1" style="background-color:#ffffcc; color:green; width:806px" %)

299

|**AT Commands**|(% style="width:418px" %)**Description**|(% style="width:256px" %)**Example**

300

|AT+CFGDEV|(% style="width:418px" %)(((

301

This command is used to configure the RS485/TTL devices; they won’t be used during sampling.

302

303

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,

304

305

mm: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command

306

)))|(% style="width:256px" %)AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

307

308

309

=== 3.3.3 Configure read commands for each sampling ===

310

311

(((

312

During each sampling, we need confirm what commands we need to send to the RS485 sensors to read data. After the RS485 sensors send back the value, it normally include some bytes and we only need a few from them for a shorten payload.

313

314

To save the LoRaWAN network bandwidth, we might need to read data from different sensors and combine their valid value into a short payload.

315

316

This section describes how to achieve above goals.

317

318

During each sampling, the RS485-LN can support 15 commands to read sensors. And combine the return to one or several uplink payloads.

319

320

321

**Each RS485 commands include two parts:**

322

323

~1. What commands RS485-LN will send to the RS485 sensors. There are total 15 commands from **AT+COMMAD1**, **ATCOMMAND2**,…, to **AT+COMMANDF**. All commands are of same grammar.

324

325

2. How to get wanted value the from RS485 sensors returns from by 1). There are total 15 AT Commands to handle the return, commands are **AT+DATACUT1**,**AT+DATACUT2**,…, **AT+DATACUTF** corresponding to the commands from 1). All commands are of same grammar.

326

327

3. Some RS485 device might has longer delay on reply, so user can use AT+CMDDL to set the timeout for getting reply after the RS485 command is sent. For example **AT+CMDDL1=1000** to send the open time to 1000ms

328

329

330

After we got the valid value from each RS485 commands, we need to combine them together with the command **AT+DATAUP**.

331

332

333

Below are examples for the how above AT Commands works.

334

335

336

**AT+COMMANDx : **This command will be sent to RS485 devices during each sampling, Max command length is 14 bytes. The grammar is:

337

338

(% border="1" style="background-color:#4bacc6; color:white; width:499px" %)

339

|(% style="width:496px" %)(((

340

**AT+COMMANDx=xx xx xx xx xx xx xx xx xx xx xx xx,m**

341

342

**xx xx xx xx xx xx xx xx xx xx xx xx: The RS485 command to be sent**

343

344

**m: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command**

345

)))

346

347

For example, if we have a RS485 sensor. The command to get sensor value is: 01 03 0B B8 00 02 46 0A. Where 01 03 0B B8 00 02 is the Modbus command to read the register 0B B8 where stored the sensor value. The 46 0A is the CRC-16/MODBUS which calculate manually.

348

349

In the RS485-LN, we should use this command AT+COMMAND1=01 03 0B B8 00 02,1 for the same.

350

351

352

**AT+DATACUTx : **This command defines how to handle the return from AT+COMMANDx, max return length is 45 bytes.

353

354

(% border="1" style="background-color:#4bacc6; color:white; width:725px" %)

355

|(% style="width:722px" %)(((

356

**AT+DATACUTx=a,b,c**

357

358

* **a: length for the return of AT+COMMAND**

359

* **b:1: grab valid value by byte, max 6 bytes. 2: grab valid value by bytes section, max 3 sections.**

360

* **c: define the position for valid value. **

)))

**Examples:**

* Grab bytes:

[[image:image-20220602153621-1.png]]

* Grab a section.

[[image:image-20220602153621-2.png]]

373

374

375

* Grab different sections.

376

377

[[image:image-20220602153621-3.png]]

)))

=== 3.3.4 Compose the uplink payload ===

383

384

(((

385

Through AT+COMMANDx and AT+DATACUTx we got valid value from each RS485 commands, Assume these valid value are RETURN1, RETURN2, .., to RETURNx. The next step is how to compose the LoRa Uplink Payload by these RETURNs. The command is **AT+DATAUP.**

)))

(((

(% style="color:#037691" %)**Examples: AT+DATAUP=0**

)))

(((

Compose the uplink payload with value returns in sequence and send with (% style="color:red" %)**A SIGNLE UPLINK**.

)))

(((

Final Payload is

)))

(((

(% style="color:#4f81bd" %)**Battery Info+PAYVER + VALID Value from RETURN1 + Valid Value from RETURN2 + … + RETURNx**

)))

(((

Where PAYVER is defined by AT+PAYVER, below is an example screen shot.

410

)))

411

412

[[image:1653269759169-150.png||height="513" width="716"]]

413

414

415

(% style="color:#037691" %)**Examples: AT+DATAUP=1**

416

417

418

Compose the uplink payload with value returns in sequence and send with (% style="color:red" %)**Multiply UPLINKs**.

Final Payload is

(% style="color:#4f81bd" %)**Battery Info+PAYVER + PAYLOAD COUNT + PAYLOAD# + DATA**

423

424

1. PAYVER: Defined by AT+PAYVER

425

1. PAYLOAD COUNT: Total how many uplinks of this sampling.

426

1. PAYLOAD#: Number of this uplink. (from 0,1,2,3…,to PAYLOAD COUNT)

427

1. DATA: Valid value: max 8 bytes for each uplink so each uplink <= 11 bytes. For the last uplink, DATA will might less than 8 bytes

428

429

[[image:image-20220602155039-4.png]]

430

431

432

So totally there will be 3 uplinks for this sampling, each uplink include 8 bytes DATA

433

434

DATA1=RETURN1 Valid Value + the first two of Valid value of RETURN10= **20 20 0a 33 90 41 02 aa**

435

436

DATA2=3^^rd^^ ~~ 10^^th^^ byte of Valid value of RETURN10= **05 81 0a 20 20 20 20 2d**

437

438

DATA3=the rest of Valid value of RETURN10= **30**

439

440

441

(% style="color:red" %)Notice: In firmware v1.3, the Max bytes has been changed according to the max bytes in different Frequency Bands for lowest SF. As below:

442

443

~* For AU915/AS923 bands, if UplinkDwell time=0, max 51 bytes for each uplink.

444

445

* For AU915/AS923 bands, if UplinkDwell time=0, max 11 bytes for each uplink.

446

447

* For US915 band, max 11 bytes for each uplink.

448

449

~* For all other bands: max 51 bytes for each uplink.

450

451

452

Below are the uplink payloads:

453

454

[[image:1654157178836-407.png]]

455

456

457

=== 3.3.5 Uplink on demand ===

458

459

Except uplink periodically, RS485-LN is able to uplink on demand. The server send downlink command to RS485-LN and RS485 will uplink data base on the command.

460

461

Downlink control command:

462

463

**0x08 command**: Poll an uplink with current command set in RS485-LN.

464

465

**0xA8 command**: Send a command to RS485-LN and uplink the output from sensors.

=== 3.3.6 Uplink on Interrupt ===

470

471

RS485-LN support external Interrupt uplink since hardware v1.2 release.

472

473

[[image:1654157342174-798.png]]

474

475

Connect the Interrupt pin to RS485-LN INT port and connect the GND pin to V- port. When there is a high voltage (Max 24v) on INT pin. Device will send an uplink packet.

476

477

478

== 3.4 Uplink Payload ==

479

480

(% border="1" style="background-color:#4bacc6; color:white; width:734px" %)

481

|**Size(bytes)**|(% style="width:120px" %)**2**|(% style="width:116px" %)**1**|(% style="width:386px" %)**Length depends on the return from the commands**

482

|Value|(% style="width:120px" %)(((

Battery(mV)

&

Interrupt _Flag

)))|(% style="width:116px" %)(((

PAYLOAD_VER

)))|(% style="width:386px" %)If the valid payload is too long and exceed the maximum support payload length in server, server will show payload not provided in the LoRaWAN server.

493

494

Below is the decoder for the first 3 bytes. The rest bytes are dynamic depends on different RS485 sensors.

495

496

497

== 3.5 Configure RS485-BL via AT or Downlink ==

498

499

User can configure RS485-LN via AT Commands or LoRaWAN Downlink Commands

500

501

There are two kinds of Commands:

502

503

* (% style="color:#4f81bd" %)**Common Commands**(%%): They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]

504

505

* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for RS485-LN. User can see these commands below:

=== 3.5.1 Common Commands ===

510

511

They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]

512

513

514

=== 3.5.2 Sensor related commands ===

515

516

Response feature is added to the server's downlink, a special package with a FPort of 200 will be uploaded immediately after receiving the data sent by the server.

517

518

[[image:image-20220602163333-5.png||height="263" width="1160"]]

519

520

The first byte of this package represents whether the configuration is successful, 00 represents failure, 01 represents success. Except for the first byte, the other is the previous downlink. (All commands except A8 type commands are applicable)

521

522

523

3.5.3 Sensor related commands

==== ====

==== ====

Wiki source code of RS485-LN – RS485 to LoRaWAN Converter

Applications

Navigation