RS485-LN – RS485 to LoRaWAN Converter

The Dragino RS485-LN is a RS485 to LoRaWAN Converter. It converts the RS485 signal into LoRaWAN wireless signal which simplify the IoT installation and reduce the installation/maintaining cost.

22

)))

23

24

(((

25

RS485-LN allows user to monitor / control RS485 devices and reach extremely long ranges. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption. It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on.

)))

(((

For data uplink, RS485-LN sends user-defined commands to RS485 devices and gets the return from the RS485 devices. RS485-LN will process these returns according to user-define rules to get the final payload and upload to LoRaWAN server.

)))

(((

For data downlink, RS485-LN runs in LoRaWAN Class C. When there downlink commands from LoRaWAN server, RS485-LN will forward the commands from LoRaWAN server to RS485 devices.

)))

)))

[[image:1653267211009-519.png||height="419" width="724"]]

38

39

== 1.2 Specifications ==

**Hardware System:**

* STM32L072CZT6 MCU

* SX1276/78 Wireless Chip

45

* Power Consumption (exclude RS485 device):

** Idle: 32mA@12v

*

** 20dB Transmit: 65mA@12v

50

51

**Interface for Model:**

52

53

* RS485

54

* Power Input 7~~ 24V DC.

**LoRa Spec:**

* Frequency Range:

** Band 1 (HF): 862 ~~ 1020 Mhz

60

** Band 2 (LF): 410 ~~ 528 Mhz

61

* 168 dB maximum link budget.

62

* +20 dBm - 100 mW constant RF output vs.

63

* +14 dBm high efficiency PA.

64

* Programmable bit rate up to 300 kbps.

65

* High sensitivity: down to -148 dBm.

66

* Bullet-proof front end: IIP3 = -12.5 dBm.

67

* Excellent blocking immunity.

68

* Low RX current of 10.3 mA, 200 nA register retention.

69

* Fully integrated synthesizer with a resolution of 61 Hz.

70

* FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.

71

* Built-in bit synchronizer for clock recovery.

72

* Preamble detection.

73

* 127 dB Dynamic Range RSSI.

74

* Automatic RF Sense and CAD with ultra-fast AFC.

75

* Packet engine up to 256 bytes with CRC.

== 1.3 Features ==

* LoRaWAN Class A & Class C protocol (default Class C)

80

* Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865/RU864

81

* AT Commands to change parameters

82

* Remote configure parameters via LoRa Downlink

83

* Firmware upgradable via program port

84

* Support multiply RS485 devices by flexible rules

85

* Support Modbus protocol

86

* Support Interrupt uplink (Since hardware version v1.2)

87

88

== 1.4 Applications ==

89

90

* Smart Buildings & Home Automation

91

* Logistics and Supply Chain Management

* Smart Metering

* Smart Agriculture

* Smart Cities

* Smart Factory

== 1.5 Firmware Change log ==

98

99

[[RS485-LN Image files – Download link and Change log>>url:http://www.dragino.com/downloads/index.php?dir=RS485-LN/]]

100

101

== 1.6 Hardware Change log ==

(((

(((

v1.2: Add External Interrupt Pin.

v1.0: Release

)))

)))

= 2. Power ON Device =

112

113

(((

114

The RS485-LN can be powered by 7 ~~ 24V DC power source. Connection as below

115

116

* Power Source VIN to RS485-LN VIN+

117

* Power Source GND to RS485-LN VIN-

118

119

(((

120

Once there is power, the RS485-LN will be on.

121

)))

122

123

[[image:1653268091319-405.png]]

124

)))

125

126

= 3. Operation Mode =

127

128

== 3.1 How it works? ==

129

130

(((

131

The RS485-LN is configured as LoRaWAN OTAA Class C mode by default. It has OTAA keys to join network. To connect a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the RS485-LN. It will auto join the network via OTAA.

132

)))

133

134

== 3.2 Example to join LoRaWAN network ==

135

136

Here shows an example for how to join the TTN V3 Network. Below is the network structure, we use [[LG308>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/140-lg308.html]] as LoRaWAN gateway here.

137

138

[[image:1653268155545-638.png||height="334" width="724"]]

139

140

(((

141

The RS485-LN in this example connected to two RS485 devices for demonstration, user can connect to other RS485 devices via the same method. The connection is as below:

142

143

485A+ and 485B- of the sensor are connected to RS485A and RA485B of RS485-LN respectively.

144

145

[[image:1653268227651-549.png||height="592" width="720"]]

146

147

(((

148

The LG308 is already set to connect to [[TTN V3 network >>path:eu1.cloud.thethings.network/]]. So what we need to now is only configure the TTN V3:

)))

(((

**Step 1**: Create a device in TTN V3 with the OTAA keys from RS485-LN.

)))

(((

Each RS485-LN is shipped with a sticker with unique device EUI:

)))

)))

[[image:1652953462722-299.png]]

(((

(((

User can enter this key in their LoRaWAN Server portal. Below is TTN V3 screen shot:

)))

(((

Add APP EUI in the application.

)))

)))

[[image:image-20220519174512-1.png]]

173

174

[[image:image-20220519174512-2.png||height="323" width="720"]]

175

176

[[image:image-20220519174512-3.png||height="556" width="724"]]

177

178

[[image:image-20220519174512-4.png]]

179

180

You can also choose to create the device manually.

181

182

[[image:1652953542269-423.png||height="710" width="723"]]

183

184

Add APP KEY and DEV EUI

185

186

[[image:1652953553383-907.png||height="514" width="724"]]

(((

**Step 2**: Power on RS485-LN and it will auto join to the TTN V3 network. After join success, it will start to upload message to TTN V3 and user can see in the panel.

191

)))

192

193

[[image:1652953568895-172.png||height="232" width="724"]]

194

195

== 3.3 Configure Commands to read data ==

(((

(((

There are plenty of RS485 devices in the market and each device has different command to read the valid data. To support these devices in flexible, RS485-LN supports flexible command set. User can use [[AT Commands>>path:#AT_COMMAND]] or LoRaWAN Downlink Command to configure what commands RS485-LN should send for each sampling and how to handle the return from RS485 devices.

)))

(((

(% style="color:red" %)Note: below description and commands are for firmware version >v1.1, if you have firmware version v1.0. Please check the [[user manual v1.0>>url:http://www.dragino.com/downloads/index.php?dir=RS485-LN/&file=RS485-LN_UserManual_v1.0.1.pdf]] or upgrade the firmware to v1.1

)))

)))

=== 3.3.1 onfigure UART settings for RS485 or TTL communication ===

208

209

To use RS485-LN to read data from RS485 sensors, connect the RS485-LN A/B traces to the sensors. And user need to make sure RS485-LN use the match UART setting to access the sensors. The related commands for UART settings are:

210

211

(% border="1" style="background-color:#ffffcc; color:green; width:795px" %)

212

|(((

213

**AT Commands**

214

)))|(% style="width:285px" %)(((

215

**Description**

216

)))|(% style="width:347px" %)(((

**Example**

)))

|(((

AT+BAUDR

)))|(% style="width:285px" %)(((

222

Set the baud rate (for RS485 connection). Default Value is: 9600.

223

)))|(% style="width:347px" %)(((

(((

AT+BAUDR=9600

)))

(((

Options: (1200,2400,4800,14400,19200,115200)

)))

)))

|(((

AT+PARITY

)))|(% style="width:285px" %)(((

235

Set UART parity (for RS485 connection)

236

)))|(% style="width:347px" %)(((

(((

AT+PARITY=0

)))

(((

Option: 0: no parity, 1: odd parity, 2: even parity

)))

)))

|(((

AT+STOPBIT

)))|(% style="width:285px" %)(((

248

(((

249

Set serial stopbit (for RS485 connection)

)))

(((

)))

)))|(% style="width:347px" %)(((

256

(((

257

AT+STOPBIT=0 for 1bit

)))

(((

AT+STOPBIT=1 for 1.5 bit

)))

(((

AT+STOPBIT=2 for 2 bits

)))

)))

=== 3.3.2 Configure sensors ===

270

271

(((

272

Some sensors might need to configure before normal operation. User can configure such sensor via PC or through RS485-BL AT Commands (% style="color:#4f81bd" %)**AT+CFGDEV**.

)))

(((

When user issue an (% style="color:#4f81bd" %)**AT+CFGDEV**(%%) command, Each (% style="color:#4f81bd" %)**AT+CFGDEV**(%%) equals to send a command to the RS485 or TTL sensors. This command will only run when user input it and won’t run during each sampling.

277

)))

278

279

(% border="1" style="background-color:#ffffcc; color:green; width:806px" %)

280

|**AT Commands**|(% style="width:418px" %)**Description**|(% style="width:256px" %)**Example**

281

|AT+CFGDEV|(% style="width:418px" %)(((

282

This command is used to configure the RS485/TTL devices; they won’t be used during sampling.

283

284

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,

285

286

mm: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command

287

)))|(% style="width:256px" %)AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

288

289

Detail of AT+CFGDEV command see [[AT+CFGDEV detail>>path:#AT_CFGDEV]].

290

291

=== 3.3.3 Configure read commands for each sampling ===

292

293

(((

294

RS485-BL is a battery powered device; it will sleep most of time. And wake up on each period and read RS485 / TTL sensor data and uplink.

)))

(((

During each sampling, we need to confirm what commands we need to send to the sensors to read data. After the RS485/TTL sensors send back the value, it normally includes some bytes and we only need a few from them for a shorten payload.

)))

(((

To save the LoRaWAN network bandwidth, we might need to read data from different sensors and combine their valid value into a short payload.

)))

(((

This section describes how to achieve above goals.

)))

(((

During each sampling, the RS485-BL can support 15 commands to read sensors. And combine the return to one or several uplink payloads.

)))

(((

**Command from RS485-BL to Sensor:**

)))

(((

RS485-BL can send out pre-set max 15 strings via **AT+COMMAD1**, **ATCOMMAND2**,…, to **AT+COMMANDF** . All commands are of same grammar.

)))

(((

**Handle return from sensors to RS485-BL**:

)))

(((

After RS485-BL send out a string to sensor, RS485-BL will wait for the return from RS485 or TTL sensor. And user can specify how to handle the return, by **AT+DATACUT or AT+SEARCH commands**

)))

* (((

**AT+DATACUT**

)))

(((

When the return value from sensor have fix length and we know which position the valid value we should get, we can use AT+DATACUT command.

)))

* (((

**AT+SEARCH**

)))

(((

When the return value from sensor is dynamic length and we are not sure which bytes the valid data is, instead, we know what value the valid value following. We can use AT+SEARCH to search the valid value in the return string.

)))

(((

**Define wait timeout:**

)))

(((

Some RS485 device might has longer delay on reply, so user can use AT+CMDDL to set the timeout for getting reply after the RS485 command is sent. For example, AT+CMDDL1=1000 to send the open time to 1000ms

)))

(((

After we got the valid value from each RS485 commands, we need to combine them together with the command **AT+DATAUP**.

)))

**Examples:**

Below are examples for the how above AT Commands works.

360

361

**AT+COMMANDx : **This command will be sent to RS485/TTL devices during each sampling, Max command length is 14 bytes. The grammar is:

362

363

(% border="1" class="table-bordered" %)

364

|(((

365

**AT+COMMANDx=xx xx xx xx xx xx xx xx xx xx xx xx,m**

366

367

**xx xx xx xx xx xx xx xx xx xx xx xx: The RS485 command to be sent**

368

369

**m: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command**

370

)))

371

372

For example, if we have a RS485 sensor. The command to get sensor value is: 01 03 0B B8 00 02 46 0A. Where 01 03 0B B8 00 02 is the Modbus command to read the register 0B B8 where stored the sensor value. The 46 0A is the CRC-16/MODBUS which calculate manually.

373

374

In the RS485-BL, we should use this command AT+COMMAND1=01 03 0B B8 00 02,1 for the same.

375

376

**AT+SEARCHx**: This command defines how to handle the return from AT+COMMANDx.

377

378

(% border="1" class="table-bordered" %)

379

|(((

380

**AT+SEARCHx=aa,xx xx xx xx xx**

381

382

* **aa: 1: prefix match mode; 2: prefix and suffix match mode**

383

* **xx xx xx xx xx: match string. Max 5 bytes for prefix and 5 bytes for suffix**

)))

Examples:

1. For a return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

391

392

If we set AT+SEARCH1=1,1E 56 34. (max 5 bytes for prefix)

393

394

The valid data will be all bytes after 1E 56 34 , so it is 2e 30 58 5f 36 41 30 31 00 49

395

396

[[image:1652954654347-831.png]]

397

398

399

1. For a return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

400

401

If we set AT+SEARCH1=2, 1E 56 34+31 00 49

402

403

Device will search the bytes between 1E 56 34 and 31 00 49. So it is 2e 30 58 5f 36 41 30

404

405

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image014.png]]

406

407

408

**AT+DATACUTx : **This command defines how to handle the return from AT+COMMANDx, max return length is 45 bytes.

409

410

|(((

411

**AT+DATACUTx=a,b,c**

412

413

* **a: length for the return of AT+COMMAND**

414

* **b:1: grab valid value by byte, max 6 bytes. 2: grab valid value by bytes section, max 3 sections.**

415

* **c: define the position for valid value. **

)))

Examples:

* Grab bytes:

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.png]]

* Grab a section.

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image016.png]]

427

428

* Grab different sections.

429

430

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.png]]

Note:

AT+SEARCHx and AT+DATACUTx can be used together, if both commands are set, RS485-BL will first process AT+SEARCHx on the return string and get a temporary string, and then process AT+DATACUTx on this temporary string to get the final payload. In this case, AT+DATACUTx need to set to format AT+DATACUTx=0,xx,xx where the return bytes set to 0.

Example:

AT+COMMAND1=11 01 1E D0,0

440

441

AT+SEARCH1=1,1E 56 34

AT+DATACUT1=0,2,1~~5

Return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

446

447

String after SEARCH command: 2e 30 58 5f 36 41 30 31 00 49

448

449

Valid payload after DataCUT command: 2e 30 58 5f 36

450

451

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image018.png]]

1.

11.

111. Compose the uplink payload

459

460

Through AT+COMMANDx and AT+DATACUTx we got valid value from each RS485 commands, Assume these valid value are RETURN1, RETURN2, .., to RETURNx. The next step is how to compose the LoRa Uplink Payload by these RETURNs. The command is **AT+DATAUP.**

461

462

463

**Examples: AT+DATAUP=0**

464

465

Compose the uplink payload with value returns in sequence and send with **A SIGNLE UPLINK**.

Final Payload is

Battery Info+PAYVER + VALID Value from RETURN1 + Valid Value from RETURN2 + … + RETURNx

470

471

Where PAYVER is defined by AT+PAYVER, below is an example screen shot.

472

473

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image019.png]]

**Examples: AT+DATAUP=1**

478

479

Compose the uplink payload with value returns in sequence and send with **Multiply UPLINKs**.

Final Payload is

Battery Info+PAYVER + PAYLOAD COUNT + PAYLOAD# + DATA

484

485

1. Battery Info (2 bytes): Battery voltage

486

1. PAYVER (1 byte): Defined by AT+PAYVER

487

1. PAYLOAD COUNT (1 byte): Total how many uplinks of this sampling.

488

1. PAYLOAD# (1 byte): Number of this uplink. (from 0,1,2,3…,to PAYLOAD COUNT)

489

1. DATA: Valid value: max 6 bytes(US915 version here, [[Notice*!>>path:#max_byte]]) for each uplink so each uplink <= 11 bytes. For the last uplink, DATA will might less than 6 bytes

490

491

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image020.png]]

492

493

494

So totally there will be 3 uplinks for this sampling, each uplink includes 6 bytes DATA

495

496

DATA1=RETURN1 Valid Value = 20 20 0a 33 90 41

497

498

DATA2=1^^st^^ ~~ 6^^th^^ byte of Valid value of RETURN10= 02 aa 05 81 0a 20

499

500

DATA3=7^^th^^ ~~ 11^^th^^ bytes of Valid value of RETURN10 = 20 20 20 2d 30

Below are the uplink payloads:

505

506

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]]

507

508

509

Notice: the Max bytes is according to the max support bytes in different Frequency Bands for lowest SF. As below:

510

511

~* For AU915/AS923 bands, if UplinkDwell time=0, max 51 bytes for each uplink ( so 51 -5 = 46 max valid date)

512

513

* For AU915/AS923 bands, if UplinkDwell time=1, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

514

515

* For US915 band, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

516

517

~* For all other bands: max 51 bytes for each uplink ( so 51 -5 = 46 max valid date).

1.

11.

111. Uplink on demand

524

525

Except uplink periodically, RS485-BL is able to uplink on demand. The server sends downlink command to RS485-BL and RS485 will uplink data base on the command.

526

527

Downlink control command:

528

529

[[0x08 command>>path:#downlink_08]]: Poll an uplink with current command set in RS485-BL.

530

531

[[0xA8 command>>path:#downlink_A8]]: Send a command to RS485-BL and uplink the output from sensors.

1.

11.

111. Uplink on Interrupt

538

539

Put the interrupt sensor between 3.3v_out and GPIO ext.[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]]

540

541

AT+INTMOD=0 Disable Interrupt

542

543

AT+INTMOD=1 Interrupt trigger by rising or falling edge.

544

545

AT+INTMOD=2 Interrupt trigger by falling edge. ( Default Value)

546

547

AT+INTMOD=3 Interrupt trigger by rising edge.

1.

11. Uplink Payload

|**Size(bytes)**|**2**|**1**|**Length depends on the return from the commands**

|Value|(((

Battery(mV)

&

Interrupt _Flag

)))|(((

PAYLOAD_VER

)))|If the valid payload is too long and exceed the maximum support payload length in server, server will show payload not provided in the LoRaWAN server.

565

566

Below is the decoder for the first 3 bytes. The rest bytes are dynamic depends on different RS485 sensors.

567

568

569

function Decoder(bytes, port) {

570

571

~/~/Payload Formats of RS485-BL Deceive

return {

~/~/Battery,units:V

BatV:((bytes[0]<<8 | bytes[1])&0x7fff)/1000,

~/~/GPIO_EXTI

EXTI_Trigger:(bytes[0] & 0x80)? "TRUE":"FALSE",

582

583

~/~/payload of version

Pay_ver:bytes[2],

};

}

TTN V3 uplink screen shot.

598

599

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

600

601

1.

602

11. Configure RS485-BL via AT or Downlink

603

604

User can configure RS485-BL via [[AT Commands >>path:#_Using_the_AT]]or LoRaWAN Downlink Commands

605

606

There are two kinds of Commands:

607

608

* **Common Commands**: They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands

609

610

* **Sensor Related Commands**: These commands are special designed for RS485-BL. User can see these commands below:

1.

11.

111. Common Commands:

615

616

They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: [[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands>>url:http://wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands]]

1.

11.

111. Sensor related commands:

622

623

==== Choose Device Type (RS485 or TTL) ====

624

625

RS485-BL can connect to either RS485 sensors or TTL sensor. User need to specify what type of sensor need to connect.

* AT Command

**AT+MOD=1** ~/~/ Set to support RS485-MODBUS type sensors. User can connect multiply RS485 , Modbus sensors to the A / B pins.

630

631

**AT+MOD=2** ~/~/ Set to support TTL Level sensors, User can connect one TTL Sensor to the TXD/RXD/GND pins.

* Downlink Payload

**0A aa** à same as AT+MOD=aa

==== [[RS485 Debug Command>>path:#downlink_A8]] (AT+CFGDEV) ====

641

642

This command is used to configure the RS485 or TTL sensors; they won’t be used during sampling.

* AT Command

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

647

648

m: 0: no CRC; 1: add CRC-16/MODBUS in the end of this command.

* Downlink Payload

Format: A8 MM NN XX XX XX XX YY

Where:

* MM: 1: add CRC-16/MODBUS ; 0: no CRC

659

* NN: The length of RS485 command

660

* XX XX XX XX: RS485 command total NN bytes

661

* YY: How many bytes will be uplink from the return of this RS485 command, if YY=0, RS485-BL will execute the downlink command without uplink; if YY>0, RS485-BL will uplink total YY bytes from the output of this RS485 command

**Example 1:**

To connect a Modbus Alarm with below commands.

666

667

* The command to active alarm is: 0A 05 00 04 00 01 4C B0. Where 0A 05 00 04 00 01 is the Modbus command to read the register 00 40 where stored the DI status. The 4C B0 is the CRC-16/MODBUS which calculate manually.

668

669

* The command to deactivate alarm is: 0A 05 00 04 00 00 8D 70. Where 0A 05 00 04 00 00 is the Modbus command to read the register 00 40 where stored the DI status. The 8D 70 is the CRC-16/MODBUS which calculate manually.

670

671

So if user want to use downlink command to control to RS485 Alarm, he can use:

672

673

**A8 01 06 0A 05 00 04 00 01 00**: to activate the RS485 Alarm

674

675

**A8 01 06 0A 05 00 04 00 00 00**: to deactivate the RS485 Alarm

676

677

A8 is type code and 01 means add CRC-16/MODBUS at the end, the 3^^rd^^ byte is 06, means the next 6 bytes are the command to be sent to the RS485 network, the final byte 00 means this command don’t need to acquire output.

**Example 2:**

Check TTL Sensor return:

683

684

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image024.png]]

==== Set Payload version ====

690

691

This is the first byte of the uplink payload. RS485-BL can connect to different sensors. User can set the PAYVER field to tell server how to decode the current payload.

* AT Command:

AT+PAYVER: Set PAYVER field = 1

* Downlink Payload:

0xAE 01 à Set PAYVER field = 0x01

701

702

0xAE 0F à Set PAYVER field = 0x0F

703

704

705

==== Set RS485 Sampling Commands ====

706

707

AT+COMMANDx, AT+DATACUTx and AT+SEARCHx

708

709

These three commands are used to configure how the RS485-BL polling data from Modbus device. Detail of usage please see : [[polling RS485 device>>path:#polling_485]].

* AT Command:

AT+COMMANDx: Configure RS485 read command to sensor.

715

716

AT+DATACUTx: Configure how to handle return from RS485 devices.

717

718

AT+SEARCHx: Configure search command

* Downlink Payload:

0xAF downlink command can be used to set AT+COMMANDx or AT+DATACUTx.

724

725

Note: if user use AT+COMMANDx to add a new command, he also need to send AT+DATACUTx downlink.

726

727

Format: AF MM NN LL XX XX XX XX YY

Where:

* MM: the ATCOMMAND or AT+DATACUT to be set. Value from 01 ~~ 0F,

732

* NN: 0: no CRC; 1: add CRC-16/MODBUS ; 2: set the AT+DATACUT value.

733

* LL: The length of AT+COMMAND or AT+DATACUT command

734

* XX XX XX XX: AT+COMMAND or AT+DATACUT command

735

* YY: If YY=0, RS485-BL will execute the downlink command without uplink; if YY=1, RS485-BL will execute an uplink after got this command.

Example:

**AF 03 01 06 0A 05 00 04 00 01 00**: Same as AT+COMMAND3=0A 05 00 04 00 01,1

740

741

**AF 03 02 06 10 01 05 06 09 0A 00**: Same as AT+DATACUT3=**16**,**1**,**5+6+9+10**

742

743

**AF 03 02 06 0B 02 05 07 08 0A 00**: Same as AT+DATACUT3=**11**,**2**,**5~~7+8~~10**

744

745

746

0xAB downlink command can be used for set AT+SEARCHx

747

748

Example: **AB aa 01 03 xx xx xx** (03 here means there are total 3 bytes after 03) So

749

750

* AB aa 01 03 xx xx xx same as AT+SEARCHaa=1,xx xx xx

751

* AB aa 02 03 xx xx xx 02 yy yy(03 means there are 3 bytes after 03, they are xx xx xx;02 means there are 2 bytes after 02, they are yy yy) so the commands

752

753

**AB aa 02 03 xx xx xx 02 yy yy** same as **AT+SEARCHaa=2,xx xx xx+yy yy**

754

755

756

==== Fast command to handle MODBUS device ====

757

758

AT+MBFUN is valid since v1.3 firmware version. The command is for fast configure to read Modbus devices. It is only valid for the devices which follow the [[MODBUS-RTU protocol>>url:https://www.modbustools.com/modbus.html]].

759

760

This command is valid since v1.3 firmware version

761

762

763

AT+MBFUN has only two value:

764

765

* AT+MBFUN=1: Enable Modbus reading. And get response base on the MODBUS return

766

767

AT+MBFUN=1, device can auto read the Modbus function code: 01, 02, 03 or 04. AT+MBFUN has lower priority vs AT+DATACUT command. If AT+DATACUT command is configured, AT+MBFUN will be ignore.

768

769

* AT+MBFUN=0: Disable Modbus fast reading.

Example:

* AT+MBFUN=1 and AT+DATACUT1/AT+DATACUT2 are not configure (0,0,0).

774

* AT+COMMAND1= 01 03 00 10 00 08,1 ~-~-> read slave address 01 , function code 03, start address 00 01, quantity of registers 00 08.

775

* AT+COMMAND2= 01 02 00 40 00 10,1 ~-~-> read slave address 01 , function code 02, start address 00 40, quantity of inputs 00 10.

776

777

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.png]]

778

779

780

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image026.png]]

* Downlink Commands:

A9 aa -à Same as AT+MBFUN=aa

786

787

788

==== RS485 command timeout ====

789

790

Some Modbus device has slow action to send replies. This command is used to configure the RS485-BL to use longer time to wait for their action.

791

792

Default value: 0, range: 0 ~~ 5 seconds

* AT Command:

AT+CMDDLaa=hex(bb cc)

Example:

**AT+CMDDL1=1000** to send the open time to 1000ms

* Downlink Payload:

0x AA aa bb cc

Same as: AT+CMDDLaa=hex(bb cc)

Example:

0xAA 01 03 E8 à Same as **AT+CMDDL1=1000 ms**

813

814

815

==== [[Uplink>>path:#downlink_A8]] payload mode ====

816

817

Define to use one uplink or multiple uplinks for the sampling.

818

819

The use of this command please see: [[Compose Uplink payload>>path:#DataUP]]

* AT Command:

AT+DATAUP=0

AT+DATAUP=1

* Downlink Payload:

0xAD 00 à Same as AT+DATAUP=0

831

832

0xAD 01 à Same as AT+DATAUP=1

833

834

835

==== Manually trigger an Uplink ====

836

837

Ask device to send an uplink immediately.

* Downlink Payload:

0x08 FF, RS485-BL will immediately send an uplink.

842

843

844

==== Clear RS485 Command ====

845

846

The AT+COMMANDx and AT+DATACUTx settings are stored in special location, user can use below command to clear them.

* AT Command:

**AT+CMDEAR=mm,nn** mm: start position of erase ,nn: stop position of erase

852

853

Etc. AT+CMDEAR=1,10 means erase AT+COMMAND1/AT+DATACUT1 to AT+COMMAND10/AT+DATACUT10

854

855

Example screen shot after clear all RS485 commands.

The uplink screen shot is:

860

861

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

* Downlink Payload:

0x09 aa bb same as AT+CMDEAR=aa,bb

867

868

869

==== Set Serial Communication Parameters ====

870

871

Set the Rs485 serial communication parameters:

* AT Command:

Set Baud Rate:

AT+BAUDR=9600 ~/~/ Options: (1200,2400,4800,14400,19200,115200)

Set UART parity

AT+PARITY=0 ~/~/ Option: 0: no parity, 1: odd parity, 2: even parity

Set STOPBIT

AT+STOPBIT=0 ~/~/ Option: 0 for 1bit; 1 for 1.5 bit ; 2 for 2 bits

* Downlink Payload:

A7 01 aa bb: Same AT+BAUDR=hex(aa bb)*100

Example:

* A7 01 00 60 same as AT+BAUDR=9600

897

* A7 01 04 80 same as AT+BAUDR=115200

898

899

A7 02 aa: Same as AT+PARITY=aa (aa value: 00 , 01 or 02)

900

901

A7 03 aa: Same as AT+STOPBIT=aa (aa value: 00 , 01 or 02)

902

903

904

==== Control output power duration ====

905

906

User can set the output power duration before each sampling.

* AT Command:

Example:

AT+3V3T=1000 ~/~/ 3V3 output power will open 1s before each sampling.

913

914

AT+5VT=1000 ~/~/ +5V output power will open 1s before each sampling.

915

916

917

* LoRaWAN Downlink Command:

918

919

07 01 aa bb Same as AT+5VT=(aa bb)

920

921

07 02 aa bb Same as AT+3V3T=(aa bb)

1.

11. Buttons

|**Button**|**Feature**

930

|**RST**|Reboot RS485-BL

1.

11. +3V3 Output

RS485-BL has a Controllable +3V3 output, user can use this output to power external sensor.

936

937

The +3V3 output will be valid for every sampling. RS485-BL will enable +3V3 output before all sampling and disable the +3V3 after all sampling.

938

939

940

The +3V3 output time can be controlled by AT Command.

**AT+3V3T=1000**

Means set +3v3 valid time to have 1000ms. So, the real +3v3 output will actually have 1000ms + sampling time for other sensors.

945

946

947

By default, the AT+3V3T=0. This is a special case, means the +3V3 output is always on at any time

1.

11. +5V Output

RS485-BL has a Controllable +5V output, user can use this output to power external sensor.

954

955

The +5V output will be valid for every sampling. RS485-BL will enable +5V output before all sampling and disable the +5v after all sampling.

956

957

958

The 5V output time can be controlled by AT Command.

**AT+5VT=1000**

Means set 5V valid time to have 1000ms. So, the real 5V output will actually have 1000ms + sampling time for other sensors.

963

964

965

By default, the AT+5VT=0. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.

1.

11. LEDs

|**LEDs**|**Feature**

974

|**LED1**|Blink when device transmit a packet.

1.

11. Switch Jumper

|**Switch Jumper**|**Feature**

980

|**SW1**|(((

981

ISP position: Upgrade firmware via UART

982

983

Flash position: Configure device, check running status.

984

)))

985

|**SW2**|(((

986

5V position: set to compatible with 5v I/O.

987

988

3.3v position: set to compatible with 3.3v I/O.,

)))

+3.3V: is always ON

+5V: Only open before every sampling. The time is by default, it is AT+5VT=0. Max open time. 5000 ms.

1. Case Study

User can check this URL for some case studies.

998

999

[[http:~~/~~/wiki.dragino.com/index.php?title=APP_RS485_COMMUNICATE_WITH_SENSORS>>url:http://wiki.dragino.com/index.php?title=APP_RS485_COMMUNICATE_WITH_SENSORS]]

1. Use AT Command

11. Access AT Command

1006

1007

RS485-BL supports AT Command set. User can use a USB to TTL adapter plus the 3.5mm Program Cable to connect to RS485-BL to use AT command, as below.

1008

1009

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image027.png]]

1010

1011

1012

In PC, User needs to set **serial tool**(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to **9600** to access to access serial console of RS485-BL. The default password is 123456. Below is the output for reference:

1013

1014

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image028.png]]

More detail AT Command manual can be found at [[AT Command Manual>>path:#AT_COMMAND]]

1.

11. Common AT Command Sequence

1024

111. Multi-channel ABP mode (Use with SX1301/LG308)

1025

1026

If device has not joined network yet:

AT+FDR

AT+NJM=0

ATZ

If device already joined network:

AT+NJM=0

ATZ

1.

11.

111. Single-channel ABP mode (Use with LG01/LG02)

1044

1045

AT+FDR Reset Parameters to Factory Default, Keys Reserve

1046

1047

AT+NJM=0 Set to ABP mode

1048

1049

AT+ADR=0 Set the Adaptive Data Rate Off

1050

1051

AT+DR=5 Set Data Rate

1052

1053

AT+TDC=60000 Set transmit interval to 60 seconds

1054

1055

AT+CHS=868400000 Set transmit frequency to 868.4Mhz

1056

1057

AT+RX2FQ=868400000 Set RX2Frequency to 868.4Mhz (according to the result from server)

1058

1059

AT+RX2DR=5 Set RX2DR to match the downlink DR from server. see below

1060

1061

AT+DADDR=26 01 1A F1 Set Device Address to 26 01 1A F1, this ID can be found in the LoRa Server portal.

ATZ Reset MCU

**Note:**

1. Make sure the device is set to ABP mode in the IoT Server.

1068

1. Make sure the LG01/02 gateway RX frequency is exactly the same as AT+CHS setting.

1069

1. Make sure SF / bandwidth setting in LG01/LG02 match the settings of AT+DR. refer [[this link>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/&file=LoRaWAN%201.0.3%20Regional%20Parameters.xlsx]] to see what DR means.

1070

1. The command AT+RX2FQ and AT+RX2DR is to let downlink work. to set the correct parameters, user can check the actually downlink parameters to be used. As below. Which shows the RX2FQ should use 868400000 and RX2DR should be 5

1071

1072

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]

1. FAQ

11. How to upgrade the image?

1077

1078

The RS485-BL LoRaWAN Controller is shipped with a 3.5mm cable, the cable is used to upload image to RS485-BL to:

1079

1080

* Support new features

1081

* For bug fix

1082

* Change LoRaWAN bands.

1083

1084

Below shows the hardware connection for how to upload an image to RS485-BL:

1085

1086

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]]

1087

1088

**Step1:** Download [[flash loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].

1089

1090

**Step2**: Download the [[LT Image files>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/image/]].

1091

1092

**Step3: **Open flashloader; choose the correct COM port to update.

|(((

HOLD PRO then press the RST button, SYS will be ON, then click next

)))

|(((

Board detected

)))

|(((

)))

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image032.png]]

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.png]]

1112

1113

1114

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image035.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]]

1.

11. How to change the LoRa Frequency Bands/Region?

1119

1120

User can follow the introduction for [[how to upgrade image>>path:#upgrade_image]]. When download the images, choose the required image file for download.

1.

11. How many RS485-Slave can RS485-BL connects?

1126

1127

The RS485-BL can support max 32 RS485 devices. Each uplink command of RS485-BL can support max 16 different RS485 command. So RS485-BL can support max 16 RS485 devices pre-program in the device for uplink. For other devices no pre-program, user can use the [[downlink message (type code 0xA8) to poll their info>>path:#downlink_A8]].

1. Trouble Shooting

11. Downlink doesn’t work, how to solve it?

1134

1135

Please see this link for debug:

1136

1137

[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#LoRaWAN_Communication_Debug>>url:http://wiki.dragino.com/index.php?title=Main_Page#LoRaWAN_Communication_Debug]]

1.

11. Why I can’t join TTN V3 in US915 /AU915 bands?

1143

1144

It might about the channels mapping. Please see for detail.

1145

1146

[[http:~~/~~/wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band>>url:http://wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band]]

1. Order Info

**Part Number: RS485-BL-XXX**

**XXX:**

* **EU433**: frequency bands EU433

1157

* **EU868**: frequency bands EU868

1158

* **KR920**: frequency bands KR920

1159

* **CN470**: frequency bands CN470

1160

* **AS923**: frequency bands AS923

1161

* **AU915**: frequency bands AU915

1162

* **US915**: frequency bands US915

1163

* **IN865**: frequency bands IN865

1164

* **RU864**: frequency bands RU864

1165

* **KZ865: **frequency bands KZ865

1. Packing Info

**Package Includes**:

1170

1171

* RS485-BL x 1

1172

* Stick Antenna for LoRa RF part x 1

1173

* Program cable x 1

1174

1175

**Dimension and weight**:

1176

1177

* Device Size: 13.5 x 7 x 3 cm

1178

* Device Weight: 105g

1179

* Package Size / pcs : 14.5 x 8 x 5 cm

1180

* Weight / pcs : 170g

1. Support

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1185

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to

1186

1187

[[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]

Wiki source code of RS485-LN – RS485 to LoRaWAN Converter

Applications

Navigation