RS485-LN – RS485 to LoRaWAN Converter

The Dragino RS485-LN is a RS485 to LoRaWAN Converter. It converts the RS485 signal into LoRaWAN wireless signal which simplify the IoT installation and reduce the installation/maintaining cost.

22

)))

23

24

(((

25

RS485-LN allows user to monitor / control RS485 devices and reach extremely long ranges. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption. It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on.

)))

(((

For data uplink, RS485-LN sends user-defined commands to RS485 devices and gets the return from the RS485 devices. RS485-LN will process these returns according to user-define rules to get the final payload and upload to LoRaWAN server.

)))

(((

For data downlink, RS485-LN runs in LoRaWAN Class C. When there downlink commands from LoRaWAN server, RS485-LN will forward the commands from LoRaWAN server to RS485 devices.

)))

)))

[[image:1653267211009-519.png||height="419" width="724"]]

38

39

== 1.2 Specifications ==

**Hardware System:**

* STM32L072CZT6 MCU

* SX1276/78 Wireless Chip

45

* Power Consumption (exclude RS485 device):

** Idle: 32mA@12v

*

** 20dB Transmit: 65mA@12v

50

51

**Interface for Model:**

52

53

* RS485

54

* Power Input 7~~ 24V DC.

**LoRa Spec:**

* Frequency Range:

** Band 1 (HF): 862 ~~ 1020 Mhz

60

** Band 2 (LF): 410 ~~ 528 Mhz

61

* 168 dB maximum link budget.

62

* +20 dBm - 100 mW constant RF output vs.

63

* +14 dBm high efficiency PA.

64

* Programmable bit rate up to 300 kbps.

65

* High sensitivity: down to -148 dBm.

66

* Bullet-proof front end: IIP3 = -12.5 dBm.

67

* Excellent blocking immunity.

68

* Low RX current of 10.3 mA, 200 nA register retention.

69

* Fully integrated synthesizer with a resolution of 61 Hz.

70

* FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.

71

* Built-in bit synchronizer for clock recovery.

72

* Preamble detection.

73

* 127 dB Dynamic Range RSSI.

74

* Automatic RF Sense and CAD with ultra-fast AFC.

75

* Packet engine up to 256 bytes with CRC.

== 1.3 Features ==

* LoRaWAN Class A & Class C protocol (default Class C)

80

* Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865/RU864

81

* AT Commands to change parameters

82

* Remote configure parameters via LoRa Downlink

83

* Firmware upgradable via program port

84

* Support multiply RS485 devices by flexible rules

85

* Support Modbus protocol

86

* Support Interrupt uplink (Since hardware version v1.2)

87

88

== 1.4 Applications ==

89

90

* Smart Buildings & Home Automation

91

* Logistics and Supply Chain Management

* Smart Metering

* Smart Agriculture

* Smart Cities

* Smart Factory

== 1.5 Firmware Change log ==

98

99

[[RS485-LN Image files – Download link and Change log>>url:http://www.dragino.com/downloads/index.php?dir=RS485-LN/]]

100

101

== 1.6 Hardware Change log ==

(((

(((

v1.2: Add External Interrupt Pin.

v1.0: Release

)))

)))

= 2. Power ON Device =

112

113

(((

114

The RS485-LN can be powered by 7 ~~ 24V DC power source. Connection as below

115

116

* Power Source VIN to RS485-LN VIN+

117

* Power Source GND to RS485-LN VIN-

118

119

(((

120

Once there is power, the RS485-LN will be on.

121

)))

122

123

[[image:1653268091319-405.png]]

124

)))

125

126

= 3. Operation Mode =

127

128

== 3.1 How it works? ==

129

130

(((

131

The RS485-LN is configured as LoRaWAN OTAA Class C mode by default. It has OTAA keys to join network. To connect a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the RS485-LN. It will auto join the network via OTAA.

132

)))

133

134

== 3.2 Example to join LoRaWAN network ==

135

136

Here shows an example for how to join the TTN V3 Network. Below is the network structure, we use [[LG308>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/140-lg308.html]] as LoRaWAN gateway here.

137

138

[[image:1653268155545-638.png||height="334" width="724"]]

139

140

(((

141

The RS485-LN in this example connected to two RS485 devices for demonstration, user can connect to other RS485 devices via the same method. The connection is as below:

142

143

485A+ and 485B- of the sensor are connected to RS485A and RA485B of RS485-LN respectively.

144

145

[[image:1653268227651-549.png||height="592" width="720"]]

146

147

(((

148

The LG308 is already set to connect to [[TTN V3 network >>path:eu1.cloud.thethings.network/]]. So what we need to now is only configure the TTN V3:

)))

(((

**Step 1**: Create a device in TTN V3 with the OTAA keys from RS485-LN.

)))

(((

Each RS485-LN is shipped with a sticker with unique device EUI:

)))

)))

[[image:1652953462722-299.png]]

(((

(((

User can enter this key in their LoRaWAN Server portal. Below is TTN V3 screen shot:

)))

(((

Add APP EUI in the application.

)))

)))

[[image:image-20220519174512-1.png]]

173

174

[[image:image-20220519174512-2.png||height="323" width="720"]]

175

176

[[image:image-20220519174512-3.png||height="556" width="724"]]

177

178

[[image:image-20220519174512-4.png]]

179

180

You can also choose to create the device manually.

181

182

[[image:1652953542269-423.png||height="710" width="723"]]

183

184

Add APP KEY and DEV EUI

185

186

[[image:1652953553383-907.png||height="514" width="724"]]

(((

**Step 2**: Power on RS485-BL and it will auto join to the TTN V3 network. After join success, it will start to upload message to TTN V3 and user can see in the panel.

191

)))

192

193

[[image:1652953568895-172.png||height="232" width="724"]]

194

195

== 3.3 Configure Commands to read data ==

196

197

(((

198

There are plenty of RS485 and TTL level devices in the market and each device has different command to read the valid data. To support these devices in flexible, RS485-BL supports flexible command set. User can use [[AT Commands or LoRaWAN Downlink>>path:#AT_COMMAND]] Command to configure how RS485-BL should read the sensor and how to handle the return from RS485 or TTL sensors.

199

)))

200

201

=== 3.3.1 onfigure UART settings for RS485 or TTL communication ===

202

203

RS485-BL can connect to either RS485 sensors or TTL sensor. User need to specify what type of sensor need to connect.

204

205

**~1. RS485-MODBUS mode:**

206

207

AT+MOD=1 ~/~/ Support RS485-MODBUS type sensors. User can connect multiply RS485 , Modbus sensors to the A / B pins.

**2. TTL mode:**

AT+MOD=2 ~/~/ Support TTL Level sensors, User can connect one TTL Sensor to the TXD/RXD/GND pins.

212

213

RS485-BL default UART settings is **9600, no parity, stop bit 1**. If the sensor has a different settings, user can change the RS485-BL setting to match.

214

215

(% border="1" style="background-color:#ffffcc; color:green; width:795px" %)

216

|(((

217

**AT Commands**

218

)))|(% style="width:285px" %)(((

219

**Description**

220

)))|(% style="width:347px" %)(((

**Example**

)))

|(((

AT+BAUDR

)))|(% style="width:285px" %)(((

226

Set the baud rate (for RS485 connection). Default Value is: 9600.

227

)))|(% style="width:347px" %)(((

(((

AT+BAUDR=9600

)))

(((

Options: (1200,2400,4800,14400,19200,115200)

)))

)))

|(((

AT+PARITY

)))|(% style="width:285px" %)(((

239

(((

240

Set UART parity (for RS485 connection)

)))

(((

Default Value is: no parity.

245

)))

246

)))|(% style="width:347px" %)(((

(((

AT+PARITY=0

)))

(((

Option: 0: no parity, 1: odd parity, 2: even parity

)))

)))

|(((

AT+STOPBIT

)))|(% style="width:285px" %)(((

258

(((

259

Set serial stopbit (for RS485 connection)

)))

(((

Default Value is: 1bit.

264

)))

265

)))|(% style="width:347px" %)(((

266

(((

267

AT+STOPBIT=0 for 1bit

)))

(((

AT+STOPBIT=1 for 1.5 bit

)))

(((

AT+STOPBIT=2 for 2 bits

)))

)))

=== 3.3.2 Configure sensors ===

280

281

(((

282

Some sensors might need to configure before normal operation. User can configure such sensor via PC or through RS485-BL AT Commands (% style="color:#4f81bd" %)**AT+CFGDEV**.

)))

(((

When user issue an (% style="color:#4f81bd" %)**AT+CFGDEV**(%%) command, Each (% style="color:#4f81bd" %)**AT+CFGDEV**(%%) equals to send a command to the RS485 or TTL sensors. This command will only run when user input it and won’t run during each sampling.

287

)))

288

289

(% border="1" style="background-color:#ffffcc; color:green; width:806px" %)

290

|**AT Commands**|(% style="width:418px" %)**Description**|(% style="width:256px" %)**Example**

291

|AT+CFGDEV|(% style="width:418px" %)(((

292

This command is used to configure the RS485/TTL devices; they won’t be used during sampling.

293

294

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,

295

296

mm: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command

297

)))|(% style="width:256px" %)AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

298

299

Detail of AT+CFGDEV command see [[AT+CFGDEV detail>>path:#AT_CFGDEV]].

300

301

=== 3.3.3 Configure read commands for each sampling ===

302

303

(((

304

RS485-BL is a battery powered device; it will sleep most of time. And wake up on each period and read RS485 / TTL sensor data and uplink.

)))

(((

During each sampling, we need to confirm what commands we need to send to the sensors to read data. After the RS485/TTL sensors send back the value, it normally includes some bytes and we only need a few from them for a shorten payload.

)))

(((

To save the LoRaWAN network bandwidth, we might need to read data from different sensors and combine their valid value into a short payload.

)))

(((

This section describes how to achieve above goals.

)))

(((

During each sampling, the RS485-BL can support 15 commands to read sensors. And combine the return to one or several uplink payloads.

)))

(((

**Command from RS485-BL to Sensor:**

)))

(((

RS485-BL can send out pre-set max 15 strings via **AT+COMMAD1**, **ATCOMMAND2**,…, to **AT+COMMANDF** . All commands are of same grammar.

)))

(((

**Handle return from sensors to RS485-BL**:

)))

(((

After RS485-BL send out a string to sensor, RS485-BL will wait for the return from RS485 or TTL sensor. And user can specify how to handle the return, by **AT+DATACUT or AT+SEARCH commands**

)))

* (((

**AT+DATACUT**

)))

(((

When the return value from sensor have fix length and we know which position the valid value we should get, we can use AT+DATACUT command.

)))

* (((

**AT+SEARCH**

)))

(((

When the return value from sensor is dynamic length and we are not sure which bytes the valid data is, instead, we know what value the valid value following. We can use AT+SEARCH to search the valid value in the return string.

)))

(((

**Define wait timeout:**

)))

(((

Some RS485 device might has longer delay on reply, so user can use AT+CMDDL to set the timeout for getting reply after the RS485 command is sent. For example, AT+CMDDL1=1000 to send the open time to 1000ms

)))

(((

After we got the valid value from each RS485 commands, we need to combine them together with the command **AT+DATAUP**.

)))

**Examples:**

Below are examples for the how above AT Commands works.

370

371

**AT+COMMANDx : **This command will be sent to RS485/TTL devices during each sampling, Max command length is 14 bytes. The grammar is:

372

373

(% border="1" class="table-bordered" %)

374

|(((

375

**AT+COMMANDx=xx xx xx xx xx xx xx xx xx xx xx xx,m**

376

377

**xx xx xx xx xx xx xx xx xx xx xx xx: The RS485 command to be sent**

378

379

**m: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command**

380

)))

381

382

For example, if we have a RS485 sensor. The command to get sensor value is: 01 03 0B B8 00 02 46 0A. Where 01 03 0B B8 00 02 is the Modbus command to read the register 0B B8 where stored the sensor value. The 46 0A is the CRC-16/MODBUS which calculate manually.

383

384

In the RS485-BL, we should use this command AT+COMMAND1=01 03 0B B8 00 02,1 for the same.

385

386

**AT+SEARCHx**: This command defines how to handle the return from AT+COMMANDx.

387

388

(% border="1" class="table-bordered" %)

389

|(((

390

**AT+SEARCHx=aa,xx xx xx xx xx**

391

392

* **aa: 1: prefix match mode; 2: prefix and suffix match mode**

393

* **xx xx xx xx xx: match string. Max 5 bytes for prefix and 5 bytes for suffix**

)))

Examples:

1. For a return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

401

402

If we set AT+SEARCH1=1,1E 56 34. (max 5 bytes for prefix)

403

404

The valid data will be all bytes after 1E 56 34 , so it is 2e 30 58 5f 36 41 30 31 00 49

405

406

[[image:1652954654347-831.png]]

407

408

409

1. For a return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

410

411

If we set AT+SEARCH1=2, 1E 56 34+31 00 49

412

413

Device will search the bytes between 1E 56 34 and 31 00 49. So it is 2e 30 58 5f 36 41 30

414

415

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image014.png]]

416

417

418

**AT+DATACUTx : **This command defines how to handle the return from AT+COMMANDx, max return length is 45 bytes.

419

420

|(((

421

**AT+DATACUTx=a,b,c**

422

423

* **a: length for the return of AT+COMMAND**

424

* **b:1: grab valid value by byte, max 6 bytes. 2: grab valid value by bytes section, max 3 sections.**

425

* **c: define the position for valid value. **

)))

Examples:

* Grab bytes:

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.png]]

* Grab a section.

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image016.png]]

437

438

* Grab different sections.

439

440

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.png]]

Note:

AT+SEARCHx and AT+DATACUTx can be used together, if both commands are set, RS485-BL will first process AT+SEARCHx on the return string and get a temporary string, and then process AT+DATACUTx on this temporary string to get the final payload. In this case, AT+DATACUTx need to set to format AT+DATACUTx=0,xx,xx where the return bytes set to 0.

Example:

AT+COMMAND1=11 01 1E D0,0

450

451

AT+SEARCH1=1,1E 56 34

AT+DATACUT1=0,2,1~~5

Return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

456

457

String after SEARCH command: 2e 30 58 5f 36 41 30 31 00 49

458

459

Valid payload after DataCUT command: 2e 30 58 5f 36

460

461

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image018.png]]

1.

11.

111. Compose the uplink payload

469

470

Through AT+COMMANDx and AT+DATACUTx we got valid value from each RS485 commands, Assume these valid value are RETURN1, RETURN2, .., to RETURNx. The next step is how to compose the LoRa Uplink Payload by these RETURNs. The command is **AT+DATAUP.**

471

472

473

**Examples: AT+DATAUP=0**

474

475

Compose the uplink payload with value returns in sequence and send with **A SIGNLE UPLINK**.

Final Payload is

Battery Info+PAYVER + VALID Value from RETURN1 + Valid Value from RETURN2 + … + RETURNx

480

481

Where PAYVER is defined by AT+PAYVER, below is an example screen shot.

482

483

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image019.png]]

**Examples: AT+DATAUP=1**

488

489

Compose the uplink payload with value returns in sequence and send with **Multiply UPLINKs**.

Final Payload is

Battery Info+PAYVER + PAYLOAD COUNT + PAYLOAD# + DATA

494

495

1. Battery Info (2 bytes): Battery voltage

496

1. PAYVER (1 byte): Defined by AT+PAYVER

497

1. PAYLOAD COUNT (1 byte): Total how many uplinks of this sampling.

498

1. PAYLOAD# (1 byte): Number of this uplink. (from 0,1,2,3…,to PAYLOAD COUNT)

499

1. DATA: Valid value: max 6 bytes(US915 version here, [[Notice*!>>path:#max_byte]]) for each uplink so each uplink <= 11 bytes. For the last uplink, DATA will might less than 6 bytes

500

501

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image020.png]]

502

503

504

So totally there will be 3 uplinks for this sampling, each uplink includes 6 bytes DATA

505

506

DATA1=RETURN1 Valid Value = 20 20 0a 33 90 41

507

508

DATA2=1^^st^^ ~~ 6^^th^^ byte of Valid value of RETURN10= 02 aa 05 81 0a 20

509

510

DATA3=7^^th^^ ~~ 11^^th^^ bytes of Valid value of RETURN10 = 20 20 20 2d 30

Below are the uplink payloads:

515

516

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]]

517

518

519

Notice: the Max bytes is according to the max support bytes in different Frequency Bands for lowest SF. As below:

520

521

~* For AU915/AS923 bands, if UplinkDwell time=0, max 51 bytes for each uplink ( so 51 -5 = 46 max valid date)

522

523

* For AU915/AS923 bands, if UplinkDwell time=1, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

524

525

* For US915 band, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

526

527

~* For all other bands: max 51 bytes for each uplink ( so 51 -5 = 46 max valid date).

1.

11.

111. Uplink on demand

534

535

Except uplink periodically, RS485-BL is able to uplink on demand. The server sends downlink command to RS485-BL and RS485 will uplink data base on the command.

536

537

Downlink control command:

538

539

[[0x08 command>>path:#downlink_08]]: Poll an uplink with current command set in RS485-BL.

540

541

[[0xA8 command>>path:#downlink_A8]]: Send a command to RS485-BL and uplink the output from sensors.

1.

11.

111. Uplink on Interrupt

548

549

Put the interrupt sensor between 3.3v_out and GPIO ext.[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]]

550

551

AT+INTMOD=0 Disable Interrupt

552

553

AT+INTMOD=1 Interrupt trigger by rising or falling edge.

554

555

AT+INTMOD=2 Interrupt trigger by falling edge. ( Default Value)

556

557

AT+INTMOD=3 Interrupt trigger by rising edge.

1.

11. Uplink Payload

|**Size(bytes)**|**2**|**1**|**Length depends on the return from the commands**

|Value|(((

Battery(mV)

&

Interrupt _Flag

)))|(((

PAYLOAD_VER

)))|If the valid payload is too long and exceed the maximum support payload length in server, server will show payload not provided in the LoRaWAN server.

575

576

Below is the decoder for the first 3 bytes. The rest bytes are dynamic depends on different RS485 sensors.

577

578

579

function Decoder(bytes, port) {

580

581

~/~/Payload Formats of RS485-BL Deceive

return {

~/~/Battery,units:V

BatV:((bytes[0]<<8 | bytes[1])&0x7fff)/1000,

~/~/GPIO_EXTI

EXTI_Trigger:(bytes[0] & 0x80)? "TRUE":"FALSE",

592

593

~/~/payload of version

Pay_ver:bytes[2],

};

}

TTN V3 uplink screen shot.

608

609

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

610

611

1.

612

11. Configure RS485-BL via AT or Downlink

613

614

User can configure RS485-BL via [[AT Commands >>path:#_Using_the_AT]]or LoRaWAN Downlink Commands

615

616

There are two kinds of Commands:

617

618

* **Common Commands**: They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands

619

620

* **Sensor Related Commands**: These commands are special designed for RS485-BL. User can see these commands below:

1.

11.

111. Common Commands:

625

626

They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: [[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands>>url:http://wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands]]

1.

11.

111. Sensor related commands:

632

633

==== Choose Device Type (RS485 or TTL) ====

634

635

RS485-BL can connect to either RS485 sensors or TTL sensor. User need to specify what type of sensor need to connect.

* AT Command

**AT+MOD=1** ~/~/ Set to support RS485-MODBUS type sensors. User can connect multiply RS485 , Modbus sensors to the A / B pins.

640

641

**AT+MOD=2** ~/~/ Set to support TTL Level sensors, User can connect one TTL Sensor to the TXD/RXD/GND pins.

* Downlink Payload

**0A aa** à same as AT+MOD=aa

==== [[RS485 Debug Command>>path:#downlink_A8]] (AT+CFGDEV) ====

651

652

This command is used to configure the RS485 or TTL sensors; they won’t be used during sampling.

* AT Command

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

657

658

m: 0: no CRC; 1: add CRC-16/MODBUS in the end of this command.

* Downlink Payload

Format: A8 MM NN XX XX XX XX YY

Where:

* MM: 1: add CRC-16/MODBUS ; 0: no CRC

669

* NN: The length of RS485 command

670

* XX XX XX XX: RS485 command total NN bytes

671

* YY: How many bytes will be uplink from the return of this RS485 command, if YY=0, RS485-BL will execute the downlink command without uplink; if YY>0, RS485-BL will uplink total YY bytes from the output of this RS485 command

**Example 1:**

To connect a Modbus Alarm with below commands.

676

677

* The command to active alarm is: 0A 05 00 04 00 01 4C B0. Where 0A 05 00 04 00 01 is the Modbus command to read the register 00 40 where stored the DI status. The 4C B0 is the CRC-16/MODBUS which calculate manually.

678

679

* The command to deactivate alarm is: 0A 05 00 04 00 00 8D 70. Where 0A 05 00 04 00 00 is the Modbus command to read the register 00 40 where stored the DI status. The 8D 70 is the CRC-16/MODBUS which calculate manually.

680

681

So if user want to use downlink command to control to RS485 Alarm, he can use:

682

683

**A8 01 06 0A 05 00 04 00 01 00**: to activate the RS485 Alarm

684

685

**A8 01 06 0A 05 00 04 00 00 00**: to deactivate the RS485 Alarm

686

687

A8 is type code and 01 means add CRC-16/MODBUS at the end, the 3^^rd^^ byte is 06, means the next 6 bytes are the command to be sent to the RS485 network, the final byte 00 means this command don’t need to acquire output.

**Example 2:**

Check TTL Sensor return:

693

694

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image024.png]]

==== Set Payload version ====

700

701

This is the first byte of the uplink payload. RS485-BL can connect to different sensors. User can set the PAYVER field to tell server how to decode the current payload.

* AT Command:

AT+PAYVER: Set PAYVER field = 1

* Downlink Payload:

0xAE 01 à Set PAYVER field = 0x01

711

712

0xAE 0F à Set PAYVER field = 0x0F

713

714

715

==== Set RS485 Sampling Commands ====

716

717

AT+COMMANDx, AT+DATACUTx and AT+SEARCHx

718

719

These three commands are used to configure how the RS485-BL polling data from Modbus device. Detail of usage please see : [[polling RS485 device>>path:#polling_485]].

* AT Command:

AT+COMMANDx: Configure RS485 read command to sensor.

725

726

AT+DATACUTx: Configure how to handle return from RS485 devices.

727

728

AT+SEARCHx: Configure search command

* Downlink Payload:

0xAF downlink command can be used to set AT+COMMANDx or AT+DATACUTx.

734

735

Note: if user use AT+COMMANDx to add a new command, he also need to send AT+DATACUTx downlink.

736

737

Format: AF MM NN LL XX XX XX XX YY

Where:

* MM: the ATCOMMAND or AT+DATACUT to be set. Value from 01 ~~ 0F,

742

* NN: 0: no CRC; 1: add CRC-16/MODBUS ; 2: set the AT+DATACUT value.

743

* LL: The length of AT+COMMAND or AT+DATACUT command

744

* XX XX XX XX: AT+COMMAND or AT+DATACUT command

745

* YY: If YY=0, RS485-BL will execute the downlink command without uplink; if YY=1, RS485-BL will execute an uplink after got this command.

Example:

**AF 03 01 06 0A 05 00 04 00 01 00**: Same as AT+COMMAND3=0A 05 00 04 00 01,1

750

751

**AF 03 02 06 10 01 05 06 09 0A 00**: Same as AT+DATACUT3=**16**,**1**,**5+6+9+10**

752

753

**AF 03 02 06 0B 02 05 07 08 0A 00**: Same as AT+DATACUT3=**11**,**2**,**5~~7+8~~10**

754

755

756

0xAB downlink command can be used for set AT+SEARCHx

757

758

Example: **AB aa 01 03 xx xx xx** (03 here means there are total 3 bytes after 03) So

759

760

* AB aa 01 03 xx xx xx same as AT+SEARCHaa=1,xx xx xx

761

* AB aa 02 03 xx xx xx 02 yy yy(03 means there are 3 bytes after 03, they are xx xx xx;02 means there are 2 bytes after 02, they are yy yy) so the commands

762

763

**AB aa 02 03 xx xx xx 02 yy yy** same as **AT+SEARCHaa=2,xx xx xx+yy yy**

764

765

766

==== Fast command to handle MODBUS device ====

767

768

AT+MBFUN is valid since v1.3 firmware version. The command is for fast configure to read Modbus devices. It is only valid for the devices which follow the [[MODBUS-RTU protocol>>url:https://www.modbustools.com/modbus.html]].

769

770

This command is valid since v1.3 firmware version

771

772

773

AT+MBFUN has only two value:

774

775

* AT+MBFUN=1: Enable Modbus reading. And get response base on the MODBUS return

776

777

AT+MBFUN=1, device can auto read the Modbus function code: 01, 02, 03 or 04. AT+MBFUN has lower priority vs AT+DATACUT command. If AT+DATACUT command is configured, AT+MBFUN will be ignore.

778

779

* AT+MBFUN=0: Disable Modbus fast reading.

Example:

* AT+MBFUN=1 and AT+DATACUT1/AT+DATACUT2 are not configure (0,0,0).

784

* AT+COMMAND1= 01 03 00 10 00 08,1 ~-~-> read slave address 01 , function code 03, start address 00 01, quantity of registers 00 08.

785

* AT+COMMAND2= 01 02 00 40 00 10,1 ~-~-> read slave address 01 , function code 02, start address 00 40, quantity of inputs 00 10.

786

787

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.png]]

788

789

790

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image026.png]]

* Downlink Commands:

A9 aa -à Same as AT+MBFUN=aa

796

797

798

==== RS485 command timeout ====

799

800

Some Modbus device has slow action to send replies. This command is used to configure the RS485-BL to use longer time to wait for their action.

801

802

Default value: 0, range: 0 ~~ 5 seconds

* AT Command:

AT+CMDDLaa=hex(bb cc)

Example:

**AT+CMDDL1=1000** to send the open time to 1000ms

* Downlink Payload:

0x AA aa bb cc

Same as: AT+CMDDLaa=hex(bb cc)

Example:

0xAA 01 03 E8 à Same as **AT+CMDDL1=1000 ms**

823

824

825

==== [[Uplink>>path:#downlink_A8]] payload mode ====

826

827

Define to use one uplink or multiple uplinks for the sampling.

828

829

The use of this command please see: [[Compose Uplink payload>>path:#DataUP]]

* AT Command:

AT+DATAUP=0

AT+DATAUP=1

* Downlink Payload:

0xAD 00 à Same as AT+DATAUP=0

841

842

0xAD 01 à Same as AT+DATAUP=1

843

844

845

==== Manually trigger an Uplink ====

846

847

Ask device to send an uplink immediately.

* Downlink Payload:

0x08 FF, RS485-BL will immediately send an uplink.

852

853

854

==== Clear RS485 Command ====

855

856

The AT+COMMANDx and AT+DATACUTx settings are stored in special location, user can use below command to clear them.

* AT Command:

**AT+CMDEAR=mm,nn** mm: start position of erase ,nn: stop position of erase

862

863

Etc. AT+CMDEAR=1,10 means erase AT+COMMAND1/AT+DATACUT1 to AT+COMMAND10/AT+DATACUT10

864

865

Example screen shot after clear all RS485 commands.

The uplink screen shot is:

870

871

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

* Downlink Payload:

0x09 aa bb same as AT+CMDEAR=aa,bb

877

878

879

==== Set Serial Communication Parameters ====

880

881

Set the Rs485 serial communication parameters:

* AT Command:

Set Baud Rate:

AT+BAUDR=9600 ~/~/ Options: (1200,2400,4800,14400,19200,115200)

Set UART parity

AT+PARITY=0 ~/~/ Option: 0: no parity, 1: odd parity, 2: even parity

Set STOPBIT

AT+STOPBIT=0 ~/~/ Option: 0 for 1bit; 1 for 1.5 bit ; 2 for 2 bits

* Downlink Payload:

A7 01 aa bb: Same AT+BAUDR=hex(aa bb)*100

Example:

* A7 01 00 60 same as AT+BAUDR=9600

907

* A7 01 04 80 same as AT+BAUDR=115200

908

909

A7 02 aa: Same as AT+PARITY=aa (aa value: 00 , 01 or 02)

910

911

A7 03 aa: Same as AT+STOPBIT=aa (aa value: 00 , 01 or 02)

912

913

914

==== Control output power duration ====

915

916

User can set the output power duration before each sampling.

* AT Command:

Example:

AT+3V3T=1000 ~/~/ 3V3 output power will open 1s before each sampling.

923

924

AT+5VT=1000 ~/~/ +5V output power will open 1s before each sampling.

925

926

927

* LoRaWAN Downlink Command:

928

929

07 01 aa bb Same as AT+5VT=(aa bb)

930

931

07 02 aa bb Same as AT+3V3T=(aa bb)

1.

11. Buttons

|**Button**|**Feature**

940

|**RST**|Reboot RS485-BL

1.

11. +3V3 Output

RS485-BL has a Controllable +3V3 output, user can use this output to power external sensor.

946

947

The +3V3 output will be valid for every sampling. RS485-BL will enable +3V3 output before all sampling and disable the +3V3 after all sampling.

948

949

950

The +3V3 output time can be controlled by AT Command.

**AT+3V3T=1000**

Means set +3v3 valid time to have 1000ms. So, the real +3v3 output will actually have 1000ms + sampling time for other sensors.

955

956

957

By default, the AT+3V3T=0. This is a special case, means the +3V3 output is always on at any time

1.

11. +5V Output

RS485-BL has a Controllable +5V output, user can use this output to power external sensor.

964

965

The +5V output will be valid for every sampling. RS485-BL will enable +5V output before all sampling and disable the +5v after all sampling.

966

967

968

The 5V output time can be controlled by AT Command.

**AT+5VT=1000**

Means set 5V valid time to have 1000ms. So, the real 5V output will actually have 1000ms + sampling time for other sensors.

973

974

975

By default, the AT+5VT=0. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.

1.

11. LEDs

|**LEDs**|**Feature**

984

|**LED1**|Blink when device transmit a packet.

1.

11. Switch Jumper

|**Switch Jumper**|**Feature**

990

|**SW1**|(((

991

ISP position: Upgrade firmware via UART

992

993

Flash position: Configure device, check running status.

994

)))

995

|**SW2**|(((

996

5V position: set to compatible with 5v I/O.

997

998

3.3v position: set to compatible with 3.3v I/O.,

)))

+3.3V: is always ON

+5V: Only open before every sampling. The time is by default, it is AT+5VT=0. Max open time. 5000 ms.

1. Case Study

User can check this URL for some case studies.

1008

1009

[[http:~~/~~/wiki.dragino.com/index.php?title=APP_RS485_COMMUNICATE_WITH_SENSORS>>url:http://wiki.dragino.com/index.php?title=APP_RS485_COMMUNICATE_WITH_SENSORS]]

1. Use AT Command

11. Access AT Command

1016

1017

RS485-BL supports AT Command set. User can use a USB to TTL adapter plus the 3.5mm Program Cable to connect to RS485-BL to use AT command, as below.

1018

1019

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image027.png]]

1020

1021

1022

In PC, User needs to set **serial tool**(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to **9600** to access to access serial console of RS485-BL. The default password is 123456. Below is the output for reference:

1023

1024

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image028.png]]

More detail AT Command manual can be found at [[AT Command Manual>>path:#AT_COMMAND]]

1.

11. Common AT Command Sequence

1034

111. Multi-channel ABP mode (Use with SX1301/LG308)

1035

1036

If device has not joined network yet:

AT+FDR

AT+NJM=0

ATZ

If device already joined network:

AT+NJM=0

ATZ

1.

11.

111. Single-channel ABP mode (Use with LG01/LG02)

1054

1055

AT+FDR Reset Parameters to Factory Default, Keys Reserve

1056

1057

AT+NJM=0 Set to ABP mode

1058

1059

AT+ADR=0 Set the Adaptive Data Rate Off

1060

1061

AT+DR=5 Set Data Rate

1062

1063

AT+TDC=60000 Set transmit interval to 60 seconds

1064

1065

AT+CHS=868400000 Set transmit frequency to 868.4Mhz

1066

1067

AT+RX2FQ=868400000 Set RX2Frequency to 868.4Mhz (according to the result from server)

1068

1069

AT+RX2DR=5 Set RX2DR to match the downlink DR from server. see below

1070

1071

AT+DADDR=26 01 1A F1 Set Device Address to 26 01 1A F1, this ID can be found in the LoRa Server portal.

ATZ Reset MCU

**Note:**

1. Make sure the device is set to ABP mode in the IoT Server.

1078

1. Make sure the LG01/02 gateway RX frequency is exactly the same as AT+CHS setting.

1079

1. Make sure SF / bandwidth setting in LG01/LG02 match the settings of AT+DR. refer [[this link>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/&file=LoRaWAN%201.0.3%20Regional%20Parameters.xlsx]] to see what DR means.

1080

1. The command AT+RX2FQ and AT+RX2DR is to let downlink work. to set the correct parameters, user can check the actually downlink parameters to be used. As below. Which shows the RX2FQ should use 868400000 and RX2DR should be 5

1081

1082

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]

1. FAQ

11. How to upgrade the image?

1087

1088

The RS485-BL LoRaWAN Controller is shipped with a 3.5mm cable, the cable is used to upload image to RS485-BL to:

1089

1090

* Support new features

1091

* For bug fix

1092

* Change LoRaWAN bands.

1093

1094

Below shows the hardware connection for how to upload an image to RS485-BL:

1095

1096

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]]

1097

1098

**Step1:** Download [[flash loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].

1099

1100

**Step2**: Download the [[LT Image files>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/image/]].

1101

1102

**Step3: **Open flashloader; choose the correct COM port to update.

|(((

HOLD PRO then press the RST button, SYS will be ON, then click next

)))

|(((

Board detected

)))

|(((

)))

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image032.png]]

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.png]]

1122

1123

1124

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image035.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]]

1.

11. How to change the LoRa Frequency Bands/Region?

1129

1130

User can follow the introduction for [[how to upgrade image>>path:#upgrade_image]]. When download the images, choose the required image file for download.

1.

11. How many RS485-Slave can RS485-BL connects?

1136

1137

The RS485-BL can support max 32 RS485 devices. Each uplink command of RS485-BL can support max 16 different RS485 command. So RS485-BL can support max 16 RS485 devices pre-program in the device for uplink. For other devices no pre-program, user can use the [[downlink message (type code 0xA8) to poll their info>>path:#downlink_A8]].

1. Trouble Shooting

11. Downlink doesn’t work, how to solve it?

1144

1145

Please see this link for debug:

1146

1147

[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#LoRaWAN_Communication_Debug>>url:http://wiki.dragino.com/index.php?title=Main_Page#LoRaWAN_Communication_Debug]]

1.

11. Why I can’t join TTN V3 in US915 /AU915 bands?

1153

1154

It might about the channels mapping. Please see for detail.

1155

1156

[[http:~~/~~/wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band>>url:http://wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band]]

1. Order Info

**Part Number: RS485-BL-XXX**

**XXX:**

* **EU433**: frequency bands EU433

1167

* **EU868**: frequency bands EU868

1168

* **KR920**: frequency bands KR920

1169

* **CN470**: frequency bands CN470

1170

* **AS923**: frequency bands AS923

1171

* **AU915**: frequency bands AU915

1172

* **US915**: frequency bands US915

1173

* **IN865**: frequency bands IN865

1174

* **RU864**: frequency bands RU864

1175

* **KZ865: **frequency bands KZ865

1. Packing Info

**Package Includes**:

1180

1181

* RS485-BL x 1

1182

* Stick Antenna for LoRa RF part x 1

1183

* Program cable x 1

1184

1185

**Dimension and weight**:

1186

1187

* Device Size: 13.5 x 7 x 3 cm

1188

* Device Weight: 105g

1189

* Package Size / pcs : 14.5 x 8 x 5 cm

1190

* Weight / pcs : 170g

1. Support

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1195

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to

1196

1197

[[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]

Wiki source code of RS485-LN – RS485 to LoRaWAN Converter

Applications

Navigation