RS485-LN – RS485 to LoRaWAN Converter

The Dragino RS485-LN is a RS485 to LoRaWAN Converter. It converts the RS485 signal into LoRaWAN wireless signal which simplify the IoT installation and reduce the installation/maintaining cost.

22

)))

23

24

(((

25

RS485-LN allows user to monitor / control RS485 devices and reach extremely long ranges. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption. It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on.

)))

(((

For data uplink, RS485-LN sends user-defined commands to RS485 devices and gets the return from the RS485 devices. RS485-LN will process these returns according to user-define rules to get the final payload and upload to LoRaWAN server.

)))

(((

For data downlink, RS485-LN runs in LoRaWAN Class C. When there downlink commands from LoRaWAN server, RS485-LN will forward the commands from LoRaWAN server to RS485 devices.

)))

)))

[[image:1653267211009-519.png||height="419" width="724"]]

38

39

== 1.2 Specifications ==

**Hardware System:**

* STM32L072CZT6 MCU

* SX1276/78 Wireless Chip

45

* Power Consumption (exclude RS485 device):

** Idle: 32mA@12v

*

** 20dB Transmit: 65mA@12v

50

51

**Interface for Model:**

52

53

* RS485

54

* Power Input 7~~ 24V DC.

**LoRa Spec:**

* Frequency Range:

** Band 1 (HF): 862 ~~ 1020 Mhz

60

** Band 2 (LF): 410 ~~ 528 Mhz

61

* 168 dB maximum link budget.

62

* +20 dBm - 100 mW constant RF output vs.

63

* +14 dBm high efficiency PA.

64

* Programmable bit rate up to 300 kbps.

65

* High sensitivity: down to -148 dBm.

66

* Bullet-proof front end: IIP3 = -12.5 dBm.

67

* Excellent blocking immunity.

68

* Low RX current of 10.3 mA, 200 nA register retention.

69

* Fully integrated synthesizer with a resolution of 61 Hz.

70

* FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.

71

* Built-in bit synchronizer for clock recovery.

72

* Preamble detection.

73

* 127 dB Dynamic Range RSSI.

74

* Automatic RF Sense and CAD with ultra-fast AFC.

75

* Packet engine up to 256 bytes with CRC.

== 1.3 Features ==

* LoRaWAN Class A & Class C protocol (default Class A)

80

* Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865/RU864

81

* AT Commands to change parameters

82

* Remote configure parameters via LoRaWAN Downlink

83

* Firmware upgradable via program port

84

* Support multiply RS485 devices by flexible rules

85

* Support Modbus protocol

86

* Support Interrupt uplink

87

88

== 1.4 Applications ==

89

90

* Smart Buildings & Home Automation

91

* Logistics and Supply Chain Management

* Smart Metering

* Smart Agriculture

* Smart Cities

* Smart Factory

== 1.5 Firmware Change log ==

98

99

[[RS485-BL Image files – Download link and Change log>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/RS485-BL/Firmware/||style="background-color: rgb(255, 255, 255);"]]

100

101

== 1.6 Hardware Change log ==

(((

v1.4

)))

(((

~1. Change Power IC to TPS22916

)))

(((

v1.3

)))

(((

~1. Change JP3 from KF350-8P to KF350-11P, Add one extra interface for I2C and one extra interface for one-wire

)))

(((

v1.2

)))

(((

Release version

)))

= 2. Pin mapping and Power ON Device =

130

131

(((

132

The RS485-BL is powered on by 8500mAh battery. To save battery life, RS485-BL is shipped with power off. User can put the jumper to power on RS485-BL.

133

)))

134

135

[[image:1652953055962-143.png||height="387" width="728"]]

136

137

138

The Left TXD and RXD are TTL interface for external sensor. TTL level is controlled by 3.3/5v Jumper.

139

140

= 3. Operation Mode =

141

142

== 3.1 How it works? ==

143

144

(((

145

The RS485-BL is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join network. To connect a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the RS485-BL. It will auto join the network via OTAA.

146

)))

147

148

== 3.2 Example to join LoRaWAN network ==

149

150

Here shows an example for how to join the TTN V3 Network. Below is the network structure, we use [[LG308>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/140-lg308.html]] as LoRaWAN gateway here.

151

152

[[image:1652953414711-647.png||height="337" width="723"]]

153

154

(((

155

The RS485-BL in this example connected to two RS485 devices for demonstration, user can connect to other RS485 devices via the same method.

)))

(((

The LG308 is already set to connect to [[TTN V3 network >>url:https://www.thethingsnetwork.org/]]. So what we need to now is only configure the TTN V3:

)))

(((

**Step 1**: Create a device in TTN V3 with the OTAA keys from RS485-BL.

)))

(((

Each RS485-BL is shipped with a sticker with unique device EUI:

168

)))

169

170

[[image:1652953462722-299.png]]

171

172

(((

173

User can enter this key in their LoRaWAN Server portal. Below is TTN V3 screen shot:

)))

(((

Add APP EUI in the application.

)))

[[image:image-20220519174512-1.png]]

184

185

[[image:image-20220519174512-2.png||height="328" width="731"]]

186

187

[[image:image-20220519174512-3.png||height="556" width="724"]]

188

189

[[image:image-20220519174512-4.png]]

190

191

You can also choose to create the device manually.

192

193

[[image:1652953542269-423.png||height="710" width="723"]]

194

195

Add APP KEY and DEV EUI

196

197

[[image:1652953553383-907.png||height="514" width="724"]]

(((

**Step 2**: Power on RS485-BL and it will auto join to the TTN V3 network. After join success, it will start to upload message to TTN V3 and user can see in the panel.

202

)))

203

204

[[image:1652953568895-172.png||height="232" width="724"]]

205

206

== 3.3 Configure Commands to read data ==

207

208

(((

209

There are plenty of RS485 and TTL level devices in the market and each device has different command to read the valid data. To support these devices in flexible, RS485-BL supports flexible command set. User can use [[AT Commands or LoRaWAN Downlink>>path:#AT_COMMAND]] Command to configure how RS485-BL should read the sensor and how to handle the return from RS485 or TTL sensors.

210

)))

211

212

=== 3.3.1 onfigure UART settings for RS485 or TTL communication ===

213

214

RS485-BL can connect to either RS485 sensors or TTL sensor. User need to specify what type of sensor need to connect.

215

216

**~1. RS485-MODBUS mode:**

217

218

AT+MOD=1 ~/~/ Support RS485-MODBUS type sensors. User can connect multiply RS485 , Modbus sensors to the A / B pins.

**2. TTL mode:**

AT+MOD=2 ~/~/ Support TTL Level sensors, User can connect one TTL Sensor to the TXD/RXD/GND pins.

223

224

RS485-BL default UART settings is **9600, no parity, stop bit 1**. If the sensor has a different settings, user can change the RS485-BL setting to match.

225

226

(% border="1" style="background-color:#ffffcc; color:green; width:795px" %)

227

|(((

228

**AT Commands**

229

)))|(% style="width:285px" %)(((

230

**Description**

231

)))|(% style="width:347px" %)(((

**Example**

)))

|(((

AT+BAUDR

)))|(% style="width:285px" %)(((

237

Set the baud rate (for RS485 connection). Default Value is: 9600.

238

)))|(% style="width:347px" %)(((

(((

AT+BAUDR=9600

)))

(((

Options: (1200,2400,4800,14400,19200,115200)

)))

)))

|(((

AT+PARITY

)))|(% style="width:285px" %)(((

250

(((

251

Set UART parity (for RS485 connection)

)))

(((

Default Value is: no parity.

256

)))

257

)))|(% style="width:347px" %)(((

(((

AT+PARITY=0

)))

(((

Option: 0: no parity, 1: odd parity, 2: even parity

)))

)))

|(((

AT+STOPBIT

)))|(% style="width:285px" %)(((

269

(((

270

Set serial stopbit (for RS485 connection)

)))

(((

Default Value is: 1bit.

275

)))

276

)))|(% style="width:347px" %)(((

277

(((

278

AT+STOPBIT=0 for 1bit

)))

(((

AT+STOPBIT=1 for 1.5 bit

)))

(((

AT+STOPBIT=2 for 2 bits

)))

)))

=== 3.3.2 Configure sensors ===

291

292

(((

293

Some sensors might need to configure before normal operation. User can configure such sensor via PC or through RS485-BL AT Commands (% style="color:#4f81bd" %)**AT+CFGDEV**.

)))

(((

When user issue an (% style="color:#4f81bd" %)**AT+CFGDEV**(%%) command, Each (% style="color:#4f81bd" %)**AT+CFGDEV**(%%) equals to send a command to the RS485 or TTL sensors. This command will only run when user input it and won’t run during each sampling.

298

)))

299

300

(% border="1" style="background-color:#ffffcc; color:green; width:806px" %)

301

|**AT Commands**|(% style="width:418px" %)**Description**|(% style="width:256px" %)**Example**

302

|AT+CFGDEV|(% style="width:418px" %)(((

303

This command is used to configure the RS485/TTL devices; they won’t be used during sampling.

304

305

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,

306

307

mm: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command

308

)))|(% style="width:256px" %)AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

309

310

Detail of AT+CFGDEV command see [[AT+CFGDEV detail>>path:#AT_CFGDEV]].

311

312

=== 3.3.3 Configure read commands for each sampling ===

313

314

(((

315

RS485-BL is a battery powered device; it will sleep most of time. And wake up on each period and read RS485 / TTL sensor data and uplink.

)))

(((

During each sampling, we need to confirm what commands we need to send to the sensors to read data. After the RS485/TTL sensors send back the value, it normally includes some bytes and we only need a few from them for a shorten payload.

)))

(((

To save the LoRaWAN network bandwidth, we might need to read data from different sensors and combine their valid value into a short payload.

)))

(((

This section describes how to achieve above goals.

)))

(((

During each sampling, the RS485-BL can support 15 commands to read sensors. And combine the return to one or several uplink payloads.

)))

(((

**Command from RS485-BL to Sensor:**

)))

(((

RS485-BL can send out pre-set max 15 strings via **AT+COMMAD1**, **ATCOMMAND2**,…, to **AT+COMMANDF** . All commands are of same grammar.

)))

(((

**Handle return from sensors to RS485-BL**:

)))

(((

After RS485-BL send out a string to sensor, RS485-BL will wait for the return from RS485 or TTL sensor. And user can specify how to handle the return, by **AT+DATACUT or AT+SEARCH commands**

)))

* (((

**AT+DATACUT**

)))

(((

When the return value from sensor have fix length and we know which position the valid value we should get, we can use AT+DATACUT command.

)))

* (((

**AT+SEARCH**

)))

(((

When the return value from sensor is dynamic length and we are not sure which bytes the valid data is, instead, we know what value the valid value following. We can use AT+SEARCH to search the valid value in the return string.

)))

(((

**Define wait timeout:**

)))

(((

Some RS485 device might has longer delay on reply, so user can use AT+CMDDL to set the timeout for getting reply after the RS485 command is sent. For example, AT+CMDDL1=1000 to send the open time to 1000ms

)))

(((

After we got the valid value from each RS485 commands, we need to combine them together with the command **AT+DATAUP**.

)))

**Examples:**

Below are examples for the how above AT Commands works.

381

382

**AT+COMMANDx : **This command will be sent to RS485/TTL devices during each sampling, Max command length is 14 bytes. The grammar is:

383

384

(% border="1" class="table-bordered" %)

385

|(((

386

**AT+COMMANDx=xx xx xx xx xx xx xx xx xx xx xx xx,m**

387

388

**xx xx xx xx xx xx xx xx xx xx xx xx: The RS485 command to be sent**

389

390

**m: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command**

391

)))

392

393

For example, if we have a RS485 sensor. The command to get sensor value is: 01 03 0B B8 00 02 46 0A. Where 01 03 0B B8 00 02 is the Modbus command to read the register 0B B8 where stored the sensor value. The 46 0A is the CRC-16/MODBUS which calculate manually.

394

395

In the RS485-BL, we should use this command AT+COMMAND1=01 03 0B B8 00 02,1 for the same.

396

397

**AT+SEARCHx**: This command defines how to handle the return from AT+COMMANDx.

398

399

(% border="1" class="table-bordered" %)

400

|(((

401

**AT+SEARCHx=aa,xx xx xx xx xx**

402

403

* **aa: 1: prefix match mode; 2: prefix and suffix match mode**

404

* **xx xx xx xx xx: match string. Max 5 bytes for prefix and 5 bytes for suffix**

)))

Examples:

1. For a return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

412

413

If we set AT+SEARCH1=1,1E 56 34. (max 5 bytes for prefix)

414

415

The valid data will be all bytes after 1E 56 34 , so it is 2e 30 58 5f 36 41 30 31 00 49

416

417

[[image:1652954654347-831.png]]

418

419

420

1. For a return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

421

422

If we set AT+SEARCH1=2, 1E 56 34+31 00 49

423

424

Device will search the bytes between 1E 56 34 and 31 00 49. So it is 2e 30 58 5f 36 41 30

425

426

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image014.png]]

427

428

429

**AT+DATACUTx : **This command defines how to handle the return from AT+COMMANDx, max return length is 45 bytes.

430

431

|(((

432

**AT+DATACUTx=a,b,c**

433

434

* **a: length for the return of AT+COMMAND**

435

* **b:1: grab valid value by byte, max 6 bytes. 2: grab valid value by bytes section, max 3 sections.**

436

* **c: define the position for valid value. **

)))

Examples:

* Grab bytes:

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.png]]

* Grab a section.

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image016.png]]

448

449

* Grab different sections.

450

451

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.png]]

Note:

AT+SEARCHx and AT+DATACUTx can be used together, if both commands are set, RS485-BL will first process AT+SEARCHx on the return string and get a temporary string, and then process AT+DATACUTx on this temporary string to get the final payload. In this case, AT+DATACUTx need to set to format AT+DATACUTx=0,xx,xx where the return bytes set to 0.

Example:

AT+COMMAND1=11 01 1E D0,0

461

462

AT+SEARCH1=1,1E 56 34

AT+DATACUT1=0,2,1~~5

Return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

467

468

String after SEARCH command: 2e 30 58 5f 36 41 30 31 00 49

469

470

Valid payload after DataCUT command: 2e 30 58 5f 36

471

472

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image018.png]]

1.

11.

111. Compose the uplink payload

480

481

Through AT+COMMANDx and AT+DATACUTx we got valid value from each RS485 commands, Assume these valid value are RETURN1, RETURN2, .., to RETURNx. The next step is how to compose the LoRa Uplink Payload by these RETURNs. The command is **AT+DATAUP.**

482

483

484

**Examples: AT+DATAUP=0**

485

486

Compose the uplink payload with value returns in sequence and send with **A SIGNLE UPLINK**.

Final Payload is

Battery Info+PAYVER + VALID Value from RETURN1 + Valid Value from RETURN2 + … + RETURNx

491

492

Where PAYVER is defined by AT+PAYVER, below is an example screen shot.

493

494

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image019.png]]

**Examples: AT+DATAUP=1**

499

500

Compose the uplink payload with value returns in sequence and send with **Multiply UPLINKs**.

Final Payload is

Battery Info+PAYVER + PAYLOAD COUNT + PAYLOAD# + DATA

505

506

1. Battery Info (2 bytes): Battery voltage

507

1. PAYVER (1 byte): Defined by AT+PAYVER

508

1. PAYLOAD COUNT (1 byte): Total how many uplinks of this sampling.

509

1. PAYLOAD# (1 byte): Number of this uplink. (from 0,1,2,3…,to PAYLOAD COUNT)

510

1. DATA: Valid value: max 6 bytes(US915 version here, [[Notice*!>>path:#max_byte]]) for each uplink so each uplink <= 11 bytes. For the last uplink, DATA will might less than 6 bytes

511

512

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image020.png]]

513

514

515

So totally there will be 3 uplinks for this sampling, each uplink includes 6 bytes DATA

516

517

DATA1=RETURN1 Valid Value = 20 20 0a 33 90 41

518

519

DATA2=1^^st^^ ~~ 6^^th^^ byte of Valid value of RETURN10= 02 aa 05 81 0a 20

520

521

DATA3=7^^th^^ ~~ 11^^th^^ bytes of Valid value of RETURN10 = 20 20 20 2d 30

Below are the uplink payloads:

526

527

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]]

528

529

530

Notice: the Max bytes is according to the max support bytes in different Frequency Bands for lowest SF. As below:

531

532

~* For AU915/AS923 bands, if UplinkDwell time=0, max 51 bytes for each uplink ( so 51 -5 = 46 max valid date)

533

534

* For AU915/AS923 bands, if UplinkDwell time=1, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

535

536

* For US915 band, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

537

538

~* For all other bands: max 51 bytes for each uplink ( so 51 -5 = 46 max valid date).

1.

11.

111. Uplink on demand

545

546

Except uplink periodically, RS485-BL is able to uplink on demand. The server sends downlink command to RS485-BL and RS485 will uplink data base on the command.

547

548

Downlink control command:

549

550

[[0x08 command>>path:#downlink_08]]: Poll an uplink with current command set in RS485-BL.

551

552

[[0xA8 command>>path:#downlink_A8]]: Send a command to RS485-BL and uplink the output from sensors.

1.

11.

111. Uplink on Interrupt

559

560

Put the interrupt sensor between 3.3v_out and GPIO ext.[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]]

561

562

AT+INTMOD=0 Disable Interrupt

563

564

AT+INTMOD=1 Interrupt trigger by rising or falling edge.

565

566

AT+INTMOD=2 Interrupt trigger by falling edge. ( Default Value)

567

568

AT+INTMOD=3 Interrupt trigger by rising edge.

1.

11. Uplink Payload

|**Size(bytes)**|**2**|**1**|**Length depends on the return from the commands**

|Value|(((

Battery(mV)

&

Interrupt _Flag

)))|(((

PAYLOAD_VER

)))|If the valid payload is too long and exceed the maximum support payload length in server, server will show payload not provided in the LoRaWAN server.

586

587

Below is the decoder for the first 3 bytes. The rest bytes are dynamic depends on different RS485 sensors.

588

589

590

function Decoder(bytes, port) {

591

592

~/~/Payload Formats of RS485-BL Deceive

return {

~/~/Battery,units:V

BatV:((bytes[0]<<8 | bytes[1])&0x7fff)/1000,

~/~/GPIO_EXTI

EXTI_Trigger:(bytes[0] & 0x80)? "TRUE":"FALSE",

603

604

~/~/payload of version

Pay_ver:bytes[2],

};

}

TTN V3 uplink screen shot.

619

620

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

621

622

1.

623

11. Configure RS485-BL via AT or Downlink

624

625

User can configure RS485-BL via [[AT Commands >>path:#_Using_the_AT]]or LoRaWAN Downlink Commands

626

627

There are two kinds of Commands:

628

629

* **Common Commands**: They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands

630

631

* **Sensor Related Commands**: These commands are special designed for RS485-BL. User can see these commands below:

1.

11.

111. Common Commands:

636

637

They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: [[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands>>url:http://wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands]]

1.

11.

111. Sensor related commands:

643

644

==== Choose Device Type (RS485 or TTL) ====

645

646

RS485-BL can connect to either RS485 sensors or TTL sensor. User need to specify what type of sensor need to connect.

* AT Command

**AT+MOD=1** ~/~/ Set to support RS485-MODBUS type sensors. User can connect multiply RS485 , Modbus sensors to the A / B pins.

651

652

**AT+MOD=2** ~/~/ Set to support TTL Level sensors, User can connect one TTL Sensor to the TXD/RXD/GND pins.

* Downlink Payload

**0A aa** à same as AT+MOD=aa

==== [[RS485 Debug Command>>path:#downlink_A8]] (AT+CFGDEV) ====

662

663

This command is used to configure the RS485 or TTL sensors; they won’t be used during sampling.

* AT Command

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

668

669

m: 0: no CRC; 1: add CRC-16/MODBUS in the end of this command.

* Downlink Payload

Format: A8 MM NN XX XX XX XX YY

Where:

* MM: 1: add CRC-16/MODBUS ; 0: no CRC

680

* NN: The length of RS485 command

681

* XX XX XX XX: RS485 command total NN bytes

682

* YY: How many bytes will be uplink from the return of this RS485 command, if YY=0, RS485-BL will execute the downlink command without uplink; if YY>0, RS485-BL will uplink total YY bytes from the output of this RS485 command

**Example 1:**

To connect a Modbus Alarm with below commands.

687

688

* The command to active alarm is: 0A 05 00 04 00 01 4C B0. Where 0A 05 00 04 00 01 is the Modbus command to read the register 00 40 where stored the DI status. The 4C B0 is the CRC-16/MODBUS which calculate manually.

689

690

* The command to deactivate alarm is: 0A 05 00 04 00 00 8D 70. Where 0A 05 00 04 00 00 is the Modbus command to read the register 00 40 where stored the DI status. The 8D 70 is the CRC-16/MODBUS which calculate manually.

691

692

So if user want to use downlink command to control to RS485 Alarm, he can use:

693

694

**A8 01 06 0A 05 00 04 00 01 00**: to activate the RS485 Alarm

695

696

**A8 01 06 0A 05 00 04 00 00 00**: to deactivate the RS485 Alarm

697

698

A8 is type code and 01 means add CRC-16/MODBUS at the end, the 3^^rd^^ byte is 06, means the next 6 bytes are the command to be sent to the RS485 network, the final byte 00 means this command don’t need to acquire output.

**Example 2:**

Check TTL Sensor return:

704

705

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image024.png]]

==== Set Payload version ====

711

712

This is the first byte of the uplink payload. RS485-BL can connect to different sensors. User can set the PAYVER field to tell server how to decode the current payload.

* AT Command:

AT+PAYVER: Set PAYVER field = 1

* Downlink Payload:

0xAE 01 à Set PAYVER field = 0x01

722

723

0xAE 0F à Set PAYVER field = 0x0F

724

725

726

==== Set RS485 Sampling Commands ====

727

728

AT+COMMANDx, AT+DATACUTx and AT+SEARCHx

729

730

These three commands are used to configure how the RS485-BL polling data from Modbus device. Detail of usage please see : [[polling RS485 device>>path:#polling_485]].

* AT Command:

AT+COMMANDx: Configure RS485 read command to sensor.

736

737

AT+DATACUTx: Configure how to handle return from RS485 devices.

738

739

AT+SEARCHx: Configure search command

* Downlink Payload:

0xAF downlink command can be used to set AT+COMMANDx or AT+DATACUTx.

745

746

Note: if user use AT+COMMANDx to add a new command, he also need to send AT+DATACUTx downlink.

747

748

Format: AF MM NN LL XX XX XX XX YY

Where:

* MM: the ATCOMMAND or AT+DATACUT to be set. Value from 01 ~~ 0F,

753

* NN: 0: no CRC; 1: add CRC-16/MODBUS ; 2: set the AT+DATACUT value.

754

* LL: The length of AT+COMMAND or AT+DATACUT command

755

* XX XX XX XX: AT+COMMAND or AT+DATACUT command

756

* YY: If YY=0, RS485-BL will execute the downlink command without uplink; if YY=1, RS485-BL will execute an uplink after got this command.

Example:

**AF 03 01 06 0A 05 00 04 00 01 00**: Same as AT+COMMAND3=0A 05 00 04 00 01,1

761

762

**AF 03 02 06 10 01 05 06 09 0A 00**: Same as AT+DATACUT3=**16**,**1**,**5+6+9+10**

763

764

**AF 03 02 06 0B 02 05 07 08 0A 00**: Same as AT+DATACUT3=**11**,**2**,**5~~7+8~~10**

765

766

767

0xAB downlink command can be used for set AT+SEARCHx

768

769

Example: **AB aa 01 03 xx xx xx** (03 here means there are total 3 bytes after 03) So

770

771

* AB aa 01 03 xx xx xx same as AT+SEARCHaa=1,xx xx xx

772

* AB aa 02 03 xx xx xx 02 yy yy(03 means there are 3 bytes after 03, they are xx xx xx;02 means there are 2 bytes after 02, they are yy yy) so the commands

773

774

**AB aa 02 03 xx xx xx 02 yy yy** same as **AT+SEARCHaa=2,xx xx xx+yy yy**

775

776

777

==== Fast command to handle MODBUS device ====

778

779

AT+MBFUN is valid since v1.3 firmware version. The command is for fast configure to read Modbus devices. It is only valid for the devices which follow the [[MODBUS-RTU protocol>>url:https://www.modbustools.com/modbus.html]].

780

781

This command is valid since v1.3 firmware version

782

783

784

AT+MBFUN has only two value:

785

786

* AT+MBFUN=1: Enable Modbus reading. And get response base on the MODBUS return

787

788

AT+MBFUN=1, device can auto read the Modbus function code: 01, 02, 03 or 04. AT+MBFUN has lower priority vs AT+DATACUT command. If AT+DATACUT command is configured, AT+MBFUN will be ignore.

789

790

* AT+MBFUN=0: Disable Modbus fast reading.

Example:

* AT+MBFUN=1 and AT+DATACUT1/AT+DATACUT2 are not configure (0,0,0).

795

* AT+COMMAND1= 01 03 00 10 00 08,1 ~-~-> read slave address 01 , function code 03, start address 00 01, quantity of registers 00 08.

796

* AT+COMMAND2= 01 02 00 40 00 10,1 ~-~-> read slave address 01 , function code 02, start address 00 40, quantity of inputs 00 10.

797

798

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.png]]

799

800

801

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image026.png]]

* Downlink Commands:

A9 aa -à Same as AT+MBFUN=aa

807

808

809

==== RS485 command timeout ====

810

811

Some Modbus device has slow action to send replies. This command is used to configure the RS485-BL to use longer time to wait for their action.

812

813

Default value: 0, range: 0 ~~ 5 seconds

* AT Command:

AT+CMDDLaa=hex(bb cc)

Example:

**AT+CMDDL1=1000** to send the open time to 1000ms

* Downlink Payload:

0x AA aa bb cc

Same as: AT+CMDDLaa=hex(bb cc)

Example:

0xAA 01 03 E8 à Same as **AT+CMDDL1=1000 ms**

834

835

836

==== [[Uplink>>path:#downlink_A8]] payload mode ====

837

838

Define to use one uplink or multiple uplinks for the sampling.

839

840

The use of this command please see: [[Compose Uplink payload>>path:#DataUP]]

* AT Command:

AT+DATAUP=0

AT+DATAUP=1

* Downlink Payload:

0xAD 00 à Same as AT+DATAUP=0

852

853

0xAD 01 à Same as AT+DATAUP=1

854

855

856

==== Manually trigger an Uplink ====

857

858

Ask device to send an uplink immediately.

* Downlink Payload:

0x08 FF, RS485-BL will immediately send an uplink.

863

864

865

==== Clear RS485 Command ====

866

867

The AT+COMMANDx and AT+DATACUTx settings are stored in special location, user can use below command to clear them.

* AT Command:

**AT+CMDEAR=mm,nn** mm: start position of erase ,nn: stop position of erase

873

874

Etc. AT+CMDEAR=1,10 means erase AT+COMMAND1/AT+DATACUT1 to AT+COMMAND10/AT+DATACUT10

875

876

Example screen shot after clear all RS485 commands.

The uplink screen shot is:

881

882

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

* Downlink Payload:

0x09 aa bb same as AT+CMDEAR=aa,bb

888

889

890

==== Set Serial Communication Parameters ====

891

892

Set the Rs485 serial communication parameters:

* AT Command:

Set Baud Rate:

AT+BAUDR=9600 ~/~/ Options: (1200,2400,4800,14400,19200,115200)

Set UART parity

AT+PARITY=0 ~/~/ Option: 0: no parity, 1: odd parity, 2: even parity

Set STOPBIT

AT+STOPBIT=0 ~/~/ Option: 0 for 1bit; 1 for 1.5 bit ; 2 for 2 bits

* Downlink Payload:

A7 01 aa bb: Same AT+BAUDR=hex(aa bb)*100

Example:

* A7 01 00 60 same as AT+BAUDR=9600

918

* A7 01 04 80 same as AT+BAUDR=115200

919

920

A7 02 aa: Same as AT+PARITY=aa (aa value: 00 , 01 or 02)

921

922

A7 03 aa: Same as AT+STOPBIT=aa (aa value: 00 , 01 or 02)

923

924

925

==== Control output power duration ====

926

927

User can set the output power duration before each sampling.

* AT Command:

Example:

AT+3V3T=1000 ~/~/ 3V3 output power will open 1s before each sampling.

934

935

AT+5VT=1000 ~/~/ +5V output power will open 1s before each sampling.

936

937

938

* LoRaWAN Downlink Command:

939

940

07 01 aa bb Same as AT+5VT=(aa bb)

941

942

07 02 aa bb Same as AT+3V3T=(aa bb)

1.

11. Buttons

|**Button**|**Feature**

951

|**RST**|Reboot RS485-BL

1.

11. +3V3 Output

RS485-BL has a Controllable +3V3 output, user can use this output to power external sensor.

957

958

The +3V3 output will be valid for every sampling. RS485-BL will enable +3V3 output before all sampling and disable the +3V3 after all sampling.

959

960

961

The +3V3 output time can be controlled by AT Command.

**AT+3V3T=1000**

Means set +3v3 valid time to have 1000ms. So, the real +3v3 output will actually have 1000ms + sampling time for other sensors.

966

967

968

By default, the AT+3V3T=0. This is a special case, means the +3V3 output is always on at any time

1.

11. +5V Output

RS485-BL has a Controllable +5V output, user can use this output to power external sensor.

975

976

The +5V output will be valid for every sampling. RS485-BL will enable +5V output before all sampling and disable the +5v after all sampling.

977

978

979

The 5V output time can be controlled by AT Command.

**AT+5VT=1000**

Means set 5V valid time to have 1000ms. So, the real 5V output will actually have 1000ms + sampling time for other sensors.

984

985

986

By default, the AT+5VT=0. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.

1.

11. LEDs

|**LEDs**|**Feature**

995

|**LED1**|Blink when device transmit a packet.

1.

11. Switch Jumper

|**Switch Jumper**|**Feature**

1001

|**SW1**|(((

1002

ISP position: Upgrade firmware via UART

1003

1004

Flash position: Configure device, check running status.

1005

)))

1006

|**SW2**|(((

1007

5V position: set to compatible with 5v I/O.

1008

1009

3.3v position: set to compatible with 3.3v I/O.,

)))

+3.3V: is always ON

+5V: Only open before every sampling. The time is by default, it is AT+5VT=0. Max open time. 5000 ms.

1. Case Study

User can check this URL for some case studies.

1019

1020

[[http:~~/~~/wiki.dragino.com/index.php?title=APP_RS485_COMMUNICATE_WITH_SENSORS>>url:http://wiki.dragino.com/index.php?title=APP_RS485_COMMUNICATE_WITH_SENSORS]]

1. Use AT Command

11. Access AT Command

1027

1028

RS485-BL supports AT Command set. User can use a USB to TTL adapter plus the 3.5mm Program Cable to connect to RS485-BL to use AT command, as below.

1029

1030

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image027.png]]

1031

1032

1033

In PC, User needs to set **serial tool**(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to **9600** to access to access serial console of RS485-BL. The default password is 123456. Below is the output for reference:

1034

1035

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image028.png]]

More detail AT Command manual can be found at [[AT Command Manual>>path:#AT_COMMAND]]

1.

11. Common AT Command Sequence

1045

111. Multi-channel ABP mode (Use with SX1301/LG308)

1046

1047

If device has not joined network yet:

AT+FDR

AT+NJM=0

ATZ

If device already joined network:

AT+NJM=0

ATZ

1.

11.

111. Single-channel ABP mode (Use with LG01/LG02)

1065

1066

AT+FDR Reset Parameters to Factory Default, Keys Reserve

1067

1068

AT+NJM=0 Set to ABP mode

1069

1070

AT+ADR=0 Set the Adaptive Data Rate Off

1071

1072

AT+DR=5 Set Data Rate

1073

1074

AT+TDC=60000 Set transmit interval to 60 seconds

1075

1076

AT+CHS=868400000 Set transmit frequency to 868.4Mhz

1077

1078

AT+RX2FQ=868400000 Set RX2Frequency to 868.4Mhz (according to the result from server)

1079

1080

AT+RX2DR=5 Set RX2DR to match the downlink DR from server. see below

1081

1082

AT+DADDR=26 01 1A F1 Set Device Address to 26 01 1A F1, this ID can be found in the LoRa Server portal.

ATZ Reset MCU

**Note:**

1. Make sure the device is set to ABP mode in the IoT Server.

1089

1. Make sure the LG01/02 gateway RX frequency is exactly the same as AT+CHS setting.

1090

1. Make sure SF / bandwidth setting in LG01/LG02 match the settings of AT+DR. refer [[this link>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/&file=LoRaWAN%201.0.3%20Regional%20Parameters.xlsx]] to see what DR means.

1091

1. The command AT+RX2FQ and AT+RX2DR is to let downlink work. to set the correct parameters, user can check the actually downlink parameters to be used. As below. Which shows the RX2FQ should use 868400000 and RX2DR should be 5

1092

1093

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]

1. FAQ

11. How to upgrade the image?

1098

1099

The RS485-BL LoRaWAN Controller is shipped with a 3.5mm cable, the cable is used to upload image to RS485-BL to:

1100

1101

* Support new features

1102

* For bug fix

1103

* Change LoRaWAN bands.

1104

1105

Below shows the hardware connection for how to upload an image to RS485-BL:

1106

1107

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]]

1108

1109

**Step1:** Download [[flash loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].

1110

1111

**Step2**: Download the [[LT Image files>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/image/]].

1112

1113

**Step3: **Open flashloader; choose the correct COM port to update.

|(((

HOLD PRO then press the RST button, SYS will be ON, then click next

)))

|(((

Board detected

)))

|(((

)))

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image032.png]]

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.png]]

1133

1134

1135

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image035.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]]

1.

11. How to change the LoRa Frequency Bands/Region?

1140

1141

User can follow the introduction for [[how to upgrade image>>path:#upgrade_image]]. When download the images, choose the required image file for download.

1.

11. How many RS485-Slave can RS485-BL connects?

1147

1148

The RS485-BL can support max 32 RS485 devices. Each uplink command of RS485-BL can support max 16 different RS485 command. So RS485-BL can support max 16 RS485 devices pre-program in the device for uplink. For other devices no pre-program, user can use the [[downlink message (type code 0xA8) to poll their info>>path:#downlink_A8]].

1. Trouble Shooting

11. Downlink doesn’t work, how to solve it?

1155

1156

Please see this link for debug:

1157

1158

[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#LoRaWAN_Communication_Debug>>url:http://wiki.dragino.com/index.php?title=Main_Page#LoRaWAN_Communication_Debug]]

1.

11. Why I can’t join TTN V3 in US915 /AU915 bands?

1164

1165

It might about the channels mapping. Please see for detail.

1166

1167

[[http:~~/~~/wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band>>url:http://wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band]]

1. Order Info

**Part Number: RS485-BL-XXX**

**XXX:**

* **EU433**: frequency bands EU433

1178

* **EU868**: frequency bands EU868

1179

* **KR920**: frequency bands KR920

1180

* **CN470**: frequency bands CN470

1181

* **AS923**: frequency bands AS923

1182

* **AU915**: frequency bands AU915

1183

* **US915**: frequency bands US915

1184

* **IN865**: frequency bands IN865

1185

* **RU864**: frequency bands RU864

1186

* **KZ865: **frequency bands KZ865

1. Packing Info

**Package Includes**:

1191

1192

* RS485-BL x 1

1193

* Stick Antenna for LoRa RF part x 1

1194

* Program cable x 1

1195

1196

**Dimension and weight**:

1197

1198

* Device Size: 13.5 x 7 x 3 cm

1199

* Device Weight: 105g

1200

* Package Size / pcs : 14.5 x 8 x 5 cm

1201

* Weight / pcs : 170g

1. Support

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1206

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to

1207

1208

[[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]

Wiki source code of RS485-LN – RS485 to LoRaWAN Converter

Applications

Navigation