RS485-LN – RS485 to LoRaWAN Converter

The Dragino RS485-BL is a **RS485 / UART to LoRaWAN Converter** for Internet of Things solutions. User can connect RS485 or UART sensor to RS485-BL converter, and configure RS485-BL to periodically read sensor data and upload via LoRaWAN network to IoT server.

25

)))

26

27

(((

28

RS485-BL can interface to RS485 sensor, 3.3v/5v UART sensor or interrupt sensor. RS485-BL provides **a 3.3v output** and** a 5v output** to power external sensors. Both output voltages are controllable to minimize the total system power consumption.

)))

(((

RS485-BL is IP67 **waterproof** and powered by **8500mAh Li-SOCI2 battery**, it is designed for long term use for several years.

)))

(((

RS485-BL runs standard **LoRaWAN 1.0.3 in Class A**. It can reach long transfer range and easy to integrate with LoRaWAN compatible gateway and IoT server.

)))

(((

For data uplink, RS485-BL sends user-defined commands to RS485 devices and gets the return from the RS485 devices. RS485-BL will process these returns data according to user-define rules to get the final payload and upload to LoRaWAN server.

)))

(((

For data downlink, RS485-BL runs in LoRaWAN Class A. When there is downlink commands from LoRaWAN server, RS485-BL will forward the commands from LoRaWAN server to RS485 devices.

)))

(((

Each RS485-BL pre-load with a set of unique keys for LoRaWAN registration, register these keys to LoRaWAN server and it will auto connect after power on.

49

)))

50

51

[[image:1652953304999-717.png||height="424" width="733"]]

52

53

== 1.2 Specifications ==

**Hardware System:**

* STM32L072CZT6 MCU

* SX1276/78 Wireless Chip

59

* Power Consumption (exclude RS485 device):

** Idle: 6uA@3.3v

*

** 20dB Transmit: 130mA@3.3v

64

65

**Interface for Model:**

66

67

* 1 x RS485 Interface

68

* 1 x TTL Serial , 3.3v or 5v.

69

* 1 x I2C Interface, 3.3v or 5v.

70

* 1 x one wire interface

71

* 1 x Interrupt Interface

72

* 1 x Controllable 5V output, max

**LoRa Spec:**

* Frequency Range:

** Band 1 (HF): 862 ~~ 1020 Mhz

78

** Band 2 (LF): 410 ~~ 528 Mhz

79

* 168 dB maximum link budget.

80

* +20 dBm - 100 mW constant RF output vs.

81

* Programmable bit rate up to 300 kbps.

82

* High sensitivity: down to -148 dBm.

83

* Bullet-proof front end: IIP3 = -12.5 dBm.

84

* Excellent blocking immunity.

85

* Fully integrated synthesizer with a resolution of 61 Hz.

86

* LoRa modulation.

87

* Built-in bit synchronizer for clock recovery.

88

* Preamble detection.

89

* 127 dB Dynamic Range RSSI.

90

* Automatic RF Sense and CAD with ultra-fast AFC.

== 1.3 Features ==

* LoRaWAN Class A & Class C protocol (default Class A)

95

* Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865/RU864

96

* AT Commands to change parameters

97

* Remote configure parameters via LoRaWAN Downlink

98

* Firmware upgradable via program port

99

* Support multiply RS485 devices by flexible rules

100

* Support Modbus protocol

101

* Support Interrupt uplink

102

103

== 1.4 Applications ==

104

105

* Smart Buildings & Home Automation

106

* Logistics and Supply Chain Management

* Smart Metering

* Smart Agriculture

* Smart Cities

* Smart Factory

== 1.5 Firmware Change log ==

113

114

[[RS485-BL Image files – Download link and Change log>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/RS485-BL/Firmware/||style="background-color: rgb(255, 255, 255);"]]

115

116

== 1.6 Hardware Change log ==

(((

v1.4

)))

(((

~1. Change Power IC to TPS22916

)))

(((

v1.3

)))

(((

~1. Change JP3 from KF350-8P to KF350-11P, Add one extra interface for I2C and one extra interface for one-wire

)))

(((

v1.2

)))

(((

Release version

)))

= 2. Pin mapping and Power ON Device =

145

146

(((

147

The RS485-BL is powered on by 8500mAh battery. To save battery life, RS485-BL is shipped with power off. User can put the jumper to power on RS485-BL.

148

)))

149

150

[[image:1652953055962-143.png||height="387" width="728"]]

151

152

153

The Left TXD and RXD are TTL interface for external sensor. TTL level is controlled by 3.3/5v Jumper.

154

155

= 3. Operation Mode =

156

157

== 3.1 How it works? ==

158

159

(((

160

The RS485-BL is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join network. To connect a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the RS485-BL. It will auto join the network via OTAA.

161

)))

162

163

== 3.2 Example to join LoRaWAN network ==

164

165

Here shows an example for how to join the TTN V3 Network. Below is the network structure, we use [[LG308>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/140-lg308.html]] as LoRaWAN gateway here.

166

167

[[image:1652953414711-647.png||height="337" width="723"]]

168

169

(((

170

The RS485-BL in this example connected to two RS485 devices for demonstration, user can connect to other RS485 devices via the same method.

)))

(((

The LG308 is already set to connect to [[TTN V3 network >>url:https://www.thethingsnetwork.org/]]. So what we need to now is only configure the TTN V3:

)))

(((

**Step 1**: Create a device in TTN V3 with the OTAA keys from RS485-BL.

)))

(((

Each RS485-BL is shipped with a sticker with unique device EUI:

183

)))

184

185

[[image:1652953462722-299.png]]

186

187

(((

188

User can enter this key in their LoRaWAN Server portal. Below is TTN V3 screen shot:

)))

(((

Add APP EUI in the application.

)))

[[image:image-20220519174512-1.png]]

199

200

[[image:image-20220519174512-2.png||height="328" width="731"]]

201

202

[[image:image-20220519174512-3.png||height="556" width="724"]]

203

204

[[image:image-20220519174512-4.png]]

205

206

You can also choose to create the device manually.

207

208

[[image:1652953542269-423.png||height="710" width="723"]]

209

210

Add APP KEY and DEV EUI

211

212

[[image:1652953553383-907.png||height="514" width="724"]]

(((

**Step 2**: Power on RS485-BL and it will auto join to the TTN V3 network. After join success, it will start to upload message to TTN V3 and user can see in the panel.

217

)))

218

219

[[image:1652953568895-172.png||height="232" width="724"]]

220

221

== 3.3 Configure Commands to read data ==

222

223

(((

224

There are plenty of RS485 and TTL level devices in the market and each device has different command to read the valid data. To support these devices in flexible, RS485-BL supports flexible command set. User can use [[AT Commands or LoRaWAN Downlink>>path:#AT_COMMAND]] Command to configure how RS485-BL should read the sensor and how to handle the return from RS485 or TTL sensors.

225

)))

226

227

=== 3.3.1 onfigure UART settings for RS485 or TTL communication ===

228

229

RS485-BL can connect to either RS485 sensors or TTL sensor. User need to specify what type of sensor need to connect.

230

231

**~1. RS485-MODBUS mode:**

232

233

AT+MOD=1 ~/~/ Support RS485-MODBUS type sensors. User can connect multiply RS485 , Modbus sensors to the A / B pins.

**2. TTL mode:**

AT+MOD=2 ~/~/ Support TTL Level sensors, User can connect one TTL Sensor to the TXD/RXD/GND pins.

238

239

RS485-BL default UART settings is **9600, no parity, stop bit 1**. If the sensor has a different settings, user can change the RS485-BL setting to match.

240

241

(% border="1" style="background-color:#ffffcc; color:green; width:795px" %)

242

|(((

243

**AT Commands**

244

)))|(% style="width:285px" %)(((

245

**Description**

246

)))|(% style="width:347px" %)(((

**Example**

)))

|(((

AT+BAUDR

)))|(% style="width:285px" %)(((

252

Set the baud rate (for RS485 connection). Default Value is: 9600.

253

)))|(% style="width:347px" %)(((

(((

AT+BAUDR=9600

)))

(((

Options: (1200,2400,4800,14400,19200,115200)

)))

)))

|(((

AT+PARITY

)))|(% style="width:285px" %)(((

265

(((

266

Set UART parity (for RS485 connection)

)))

(((

Default Value is: no parity.

271

)))

272

)))|(% style="width:347px" %)(((

(((

AT+PARITY=0

)))

(((

Option: 0: no parity, 1: odd parity, 2: even parity

)))

)))

|(((

AT+STOPBIT

)))|(% style="width:285px" %)(((

284

(((

285

Set serial stopbit (for RS485 connection)

)))

(((

Default Value is: 1bit.

290

)))

291

)))|(% style="width:347px" %)(((

292

(((

293

AT+STOPBIT=0 for 1bit

)))

(((

AT+STOPBIT=1 for 1.5 bit

)))

(((

AT+STOPBIT=2 for 2 bits

)))

)))

=== 3.3.2 Configure sensors ===

306

307

(((

308

Some sensors might need to configure before normal operation. User can configure such sensor via PC or through RS485-BL AT Commands (% style="color:#4f81bd" %)**AT+CFGDEV**.

)))

(((

When user issue an (% style="color:#4f81bd" %)**AT+CFGDEV**(%%) command, Each (% style="color:#4f81bd" %)**AT+CFGDEV**(%%) equals to send a command to the RS485 or TTL sensors. This command will only run when user input it and won’t run during each sampling.

313

)))

314

315

(% border="1" style="background-color:#ffffcc; color:green; width:806px" %)

316

|**AT Commands**|(% style="width:418px" %)**Description**|(% style="width:256px" %)**Example**

317

|AT+CFGDEV|(% style="width:418px" %)(((

318

This command is used to configure the RS485/TTL devices; they won’t be used during sampling.

319

320

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,

321

322

mm: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command

323

)))|(% style="width:256px" %)AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

324

325

Detail of AT+CFGDEV command see [[AT+CFGDEV detail>>path:#AT_CFGDEV]].

326

327

=== 3.3.3 Configure read commands for each sampling ===

328

329

(((

330

RS485-BL is a battery powered device; it will sleep most of time. And wake up on each period and read RS485 / TTL sensor data and uplink.

)))

(((

During each sampling, we need to confirm what commands we need to send to the sensors to read data. After the RS485/TTL sensors send back the value, it normally includes some bytes and we only need a few from them for a shorten payload.

)))

(((

To save the LoRaWAN network bandwidth, we might need to read data from different sensors and combine their valid value into a short payload.

)))

(((

This section describes how to achieve above goals.

)))

(((

During each sampling, the RS485-BL can support 15 commands to read sensors. And combine the return to one or several uplink payloads.

)))

(((

**Command from RS485-BL to Sensor:**

)))

(((

RS485-BL can send out pre-set max 15 strings via **AT+COMMAD1**, **ATCOMMAND2**,…, to **AT+COMMANDF** . All commands are of same grammar.

)))

(((

**Handle return from sensors to RS485-BL**:

)))

(((

After RS485-BL send out a string to sensor, RS485-BL will wait for the return from RS485 or TTL sensor. And user can specify how to handle the return, by **AT+DATACUT or AT+SEARCH commands**

)))

* (((

**AT+DATACUT**

)))

(((

When the return value from sensor have fix length and we know which position the valid value we should get, we can use AT+DATACUT command.

)))

* (((

**AT+SEARCH**

)))

(((

When the return value from sensor is dynamic length and we are not sure which bytes the valid data is, instead, we know what value the valid value following. We can use AT+SEARCH to search the valid value in the return string.

)))

(((

**Define wait timeout:**

)))

(((

Some RS485 device might has longer delay on reply, so user can use AT+CMDDL to set the timeout for getting reply after the RS485 command is sent. For example, AT+CMDDL1=1000 to send the open time to 1000ms

)))

(((

After we got the valid value from each RS485 commands, we need to combine them together with the command **AT+DATAUP**.

)))

**Examples:**

Below are examples for the how above AT Commands works.

396

397

**AT+COMMANDx : **This command will be sent to RS485/TTL devices during each sampling, Max command length is 14 bytes. The grammar is:

398

399

(% border="1" class="table-bordered" %)

400

|(((

401

**AT+COMMANDx=xx xx xx xx xx xx xx xx xx xx xx xx,m**

402

403

**xx xx xx xx xx xx xx xx xx xx xx xx: The RS485 command to be sent**

404

405

**m: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command**

406

)))

407

408

For example, if we have a RS485 sensor. The command to get sensor value is: 01 03 0B B8 00 02 46 0A. Where 01 03 0B B8 00 02 is the Modbus command to read the register 0B B8 where stored the sensor value. The 46 0A is the CRC-16/MODBUS which calculate manually.

409

410

In the RS485-BL, we should use this command AT+COMMAND1=01 03 0B B8 00 02,1 for the same.

411

412

**AT+SEARCHx**: This command defines how to handle the return from AT+COMMANDx.

413

414

(% border="1" class="table-bordered" %)

415

|(((

416

**AT+SEARCHx=aa,xx xx xx xx xx**

417

418

* **aa: 1: prefix match mode; 2: prefix and suffix match mode**

419

* **xx xx xx xx xx: match string. Max 5 bytes for prefix and 5 bytes for suffix**

)))

Examples:

1. For a return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

427

428

If we set AT+SEARCH1=1,1E 56 34. (max 5 bytes for prefix)

429

430

The valid data will be all bytes after 1E 56 34 , so it is 2e 30 58 5f 36 41 30 31 00 49

431

432

[[image:1652954654347-831.png]]

433

434

435

1. For a return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

436

437

If we set AT+SEARCH1=2, 1E 56 34+31 00 49

438

439

Device will search the bytes between 1E 56 34 and 31 00 49. So it is 2e 30 58 5f 36 41 30

440

441

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image014.png]]

442

443

444

**AT+DATACUTx : **This command defines how to handle the return from AT+COMMANDx, max return length is 45 bytes.

445

446

|(((

447

**AT+DATACUTx=a,b,c**

448

449

* **a: length for the return of AT+COMMAND**

450

* **b:1: grab valid value by byte, max 6 bytes. 2: grab valid value by bytes section, max 3 sections.**

451

* **c: define the position for valid value. **

)))

Examples:

* Grab bytes:

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.png]]

* Grab a section.

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image016.png]]

463

464

* Grab different sections.

465

466

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.png]]

Note:

AT+SEARCHx and AT+DATACUTx can be used together, if both commands are set, RS485-BL will first process AT+SEARCHx on the return string and get a temporary string, and then process AT+DATACUTx on this temporary string to get the final payload. In this case, AT+DATACUTx need to set to format AT+DATACUTx=0,xx,xx where the return bytes set to 0.

Example:

AT+COMMAND1=11 01 1E D0,0

476

477

AT+SEARCH1=1,1E 56 34

AT+DATACUT1=0,2,1~~5

Return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

482

483

String after SEARCH command: 2e 30 58 5f 36 41 30 31 00 49

484

485

Valid payload after DataCUT command: 2e 30 58 5f 36

486

487

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image018.png]]

1.

11.

111. Compose the uplink payload

495

496

Through AT+COMMANDx and AT+DATACUTx we got valid value from each RS485 commands, Assume these valid value are RETURN1, RETURN2, .., to RETURNx. The next step is how to compose the LoRa Uplink Payload by these RETURNs. The command is **AT+DATAUP.**

497

498

499

**Examples: AT+DATAUP=0**

500

501

Compose the uplink payload with value returns in sequence and send with **A SIGNLE UPLINK**.

Final Payload is

Battery Info+PAYVER + VALID Value from RETURN1 + Valid Value from RETURN2 + … + RETURNx

506

507

Where PAYVER is defined by AT+PAYVER, below is an example screen shot.

508

509

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image019.png]]

**Examples: AT+DATAUP=1**

514

515

Compose the uplink payload with value returns in sequence and send with **Multiply UPLINKs**.

Final Payload is

Battery Info+PAYVER + PAYLOAD COUNT + PAYLOAD# + DATA

520

521

1. Battery Info (2 bytes): Battery voltage

522

1. PAYVER (1 byte): Defined by AT+PAYVER

523

1. PAYLOAD COUNT (1 byte): Total how many uplinks of this sampling.

524

1. PAYLOAD# (1 byte): Number of this uplink. (from 0,1,2,3…,to PAYLOAD COUNT)

525

1. DATA: Valid value: max 6 bytes(US915 version here, [[Notice*!>>path:#max_byte]]) for each uplink so each uplink <= 11 bytes. For the last uplink, DATA will might less than 6 bytes

526

527

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image020.png]]

528

529

530

So totally there will be 3 uplinks for this sampling, each uplink includes 6 bytes DATA

531

532

DATA1=RETURN1 Valid Value = 20 20 0a 33 90 41

533

534

DATA2=1^^st^^ ~~ 6^^th^^ byte of Valid value of RETURN10= 02 aa 05 81 0a 20

535

536

DATA3=7^^th^^ ~~ 11^^th^^ bytes of Valid value of RETURN10 = 20 20 20 2d 30

Below are the uplink payloads:

541

542

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]]

543

544

545

Notice: the Max bytes is according to the max support bytes in different Frequency Bands for lowest SF. As below:

546

547

~* For AU915/AS923 bands, if UplinkDwell time=0, max 51 bytes for each uplink ( so 51 -5 = 46 max valid date)

548

549

* For AU915/AS923 bands, if UplinkDwell time=1, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

550

551

* For US915 band, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

552

553

~* For all other bands: max 51 bytes for each uplink ( so 51 -5 = 46 max valid date).

1.

11.

111. Uplink on demand

560

561

Except uplink periodically, RS485-BL is able to uplink on demand. The server sends downlink command to RS485-BL and RS485 will uplink data base on the command.

562

563

Downlink control command:

564

565

[[0x08 command>>path:#downlink_08]]: Poll an uplink with current command set in RS485-BL.

566

567

[[0xA8 command>>path:#downlink_A8]]: Send a command to RS485-BL and uplink the output from sensors.

1.

11.

111. Uplink on Interrupt

574

575

Put the interrupt sensor between 3.3v_out and GPIO ext.[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]]

576

577

AT+INTMOD=0 Disable Interrupt

578

579

AT+INTMOD=1 Interrupt trigger by rising or falling edge.

580

581

AT+INTMOD=2 Interrupt trigger by falling edge. ( Default Value)

582

583

AT+INTMOD=3 Interrupt trigger by rising edge.

1.

11. Uplink Payload

|**Size(bytes)**|**2**|**1**|**Length depends on the return from the commands**

|Value|(((

Battery(mV)

&

Interrupt _Flag

)))|(((

PAYLOAD_VER

)))|If the valid payload is too long and exceed the maximum support payload length in server, server will show payload not provided in the LoRaWAN server.

601

602

Below is the decoder for the first 3 bytes. The rest bytes are dynamic depends on different RS485 sensors.

603

604

605

function Decoder(bytes, port) {

606

607

~/~/Payload Formats of RS485-BL Deceive

return {

~/~/Battery,units:V

BatV:((bytes[0]<<8 | bytes[1])&0x7fff)/1000,

~/~/GPIO_EXTI

EXTI_Trigger:(bytes[0] & 0x80)? "TRUE":"FALSE",

618

619

~/~/payload of version

Pay_ver:bytes[2],

};

}

TTN V3 uplink screen shot.

634

635

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

636

637

1.

638

11. Configure RS485-BL via AT or Downlink

639

640

User can configure RS485-BL via [[AT Commands >>path:#_Using_the_AT]]or LoRaWAN Downlink Commands

641

642

There are two kinds of Commands:

643

644

* **Common Commands**: They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands

645

646

* **Sensor Related Commands**: These commands are special designed for RS485-BL. User can see these commands below:

1.

11.

111. Common Commands:

651

652

They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: [[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands>>url:http://wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands]]

1.

11.

111. Sensor related commands:

658

659

==== Choose Device Type (RS485 or TTL) ====

660

661

RS485-BL can connect to either RS485 sensors or TTL sensor. User need to specify what type of sensor need to connect.

* AT Command

**AT+MOD=1** ~/~/ Set to support RS485-MODBUS type sensors. User can connect multiply RS485 , Modbus sensors to the A / B pins.

666

667

**AT+MOD=2** ~/~/ Set to support TTL Level sensors, User can connect one TTL Sensor to the TXD/RXD/GND pins.

* Downlink Payload

**0A aa** à same as AT+MOD=aa

==== [[RS485 Debug Command>>path:#downlink_A8]] (AT+CFGDEV) ====

677

678

This command is used to configure the RS485 or TTL sensors; they won’t be used during sampling.

* AT Command

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

683

684

m: 0: no CRC; 1: add CRC-16/MODBUS in the end of this command.

* Downlink Payload

Format: A8 MM NN XX XX XX XX YY

Where:

* MM: 1: add CRC-16/MODBUS ; 0: no CRC

695

* NN: The length of RS485 command

696

* XX XX XX XX: RS485 command total NN bytes

697

* YY: How many bytes will be uplink from the return of this RS485 command, if YY=0, RS485-BL will execute the downlink command without uplink; if YY>0, RS485-BL will uplink total YY bytes from the output of this RS485 command

**Example 1:**

To connect a Modbus Alarm with below commands.

702

703

* The command to active alarm is: 0A 05 00 04 00 01 4C B0. Where 0A 05 00 04 00 01 is the Modbus command to read the register 00 40 where stored the DI status. The 4C B0 is the CRC-16/MODBUS which calculate manually.

704

705

* The command to deactivate alarm is: 0A 05 00 04 00 00 8D 70. Where 0A 05 00 04 00 00 is the Modbus command to read the register 00 40 where stored the DI status. The 8D 70 is the CRC-16/MODBUS which calculate manually.

706

707

So if user want to use downlink command to control to RS485 Alarm, he can use:

708

709

**A8 01 06 0A 05 00 04 00 01 00**: to activate the RS485 Alarm

710

711

**A8 01 06 0A 05 00 04 00 00 00**: to deactivate the RS485 Alarm

712

713

A8 is type code and 01 means add CRC-16/MODBUS at the end, the 3^^rd^^ byte is 06, means the next 6 bytes are the command to be sent to the RS485 network, the final byte 00 means this command don’t need to acquire output.

**Example 2:**

Check TTL Sensor return:

719

720

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image024.png]]

==== Set Payload version ====

726

727

This is the first byte of the uplink payload. RS485-BL can connect to different sensors. User can set the PAYVER field to tell server how to decode the current payload.

* AT Command:

AT+PAYVER: Set PAYVER field = 1

* Downlink Payload:

0xAE 01 à Set PAYVER field = 0x01

737

738

0xAE 0F à Set PAYVER field = 0x0F

739

740

741

==== Set RS485 Sampling Commands ====

742

743

AT+COMMANDx, AT+DATACUTx and AT+SEARCHx

744

745

These three commands are used to configure how the RS485-BL polling data from Modbus device. Detail of usage please see : [[polling RS485 device>>path:#polling_485]].

* AT Command:

AT+COMMANDx: Configure RS485 read command to sensor.

751

752

AT+DATACUTx: Configure how to handle return from RS485 devices.

753

754

AT+SEARCHx: Configure search command

* Downlink Payload:

0xAF downlink command can be used to set AT+COMMANDx or AT+DATACUTx.

760

761

Note: if user use AT+COMMANDx to add a new command, he also need to send AT+DATACUTx downlink.

762

763

Format: AF MM NN LL XX XX XX XX YY

Where:

* MM: the ATCOMMAND or AT+DATACUT to be set. Value from 01 ~~ 0F,

768

* NN: 0: no CRC; 1: add CRC-16/MODBUS ; 2: set the AT+DATACUT value.

769

* LL: The length of AT+COMMAND or AT+DATACUT command

770

* XX XX XX XX: AT+COMMAND or AT+DATACUT command

771

* YY: If YY=0, RS485-BL will execute the downlink command without uplink; if YY=1, RS485-BL will execute an uplink after got this command.

Example:

**AF 03 01 06 0A 05 00 04 00 01 00**: Same as AT+COMMAND3=0A 05 00 04 00 01,1

776

777

**AF 03 02 06 10 01 05 06 09 0A 00**: Same as AT+DATACUT3=**16**,**1**,**5+6+9+10**

778

779

**AF 03 02 06 0B 02 05 07 08 0A 00**: Same as AT+DATACUT3=**11**,**2**,**5~~7+8~~10**

780

781

782

0xAB downlink command can be used for set AT+SEARCHx

783

784

Example: **AB aa 01 03 xx xx xx** (03 here means there are total 3 bytes after 03) So

785

786

* AB aa 01 03 xx xx xx same as AT+SEARCHaa=1,xx xx xx

787

* AB aa 02 03 xx xx xx 02 yy yy(03 means there are 3 bytes after 03, they are xx xx xx;02 means there are 2 bytes after 02, they are yy yy) so the commands

788

789

**AB aa 02 03 xx xx xx 02 yy yy** same as **AT+SEARCHaa=2,xx xx xx+yy yy**

790

791

792

==== Fast command to handle MODBUS device ====

793

794

AT+MBFUN is valid since v1.3 firmware version. The command is for fast configure to read Modbus devices. It is only valid for the devices which follow the [[MODBUS-RTU protocol>>url:https://www.modbustools.com/modbus.html]].

795

796

This command is valid since v1.3 firmware version

797

798

799

AT+MBFUN has only two value:

800

801

* AT+MBFUN=1: Enable Modbus reading. And get response base on the MODBUS return

802

803

AT+MBFUN=1, device can auto read the Modbus function code: 01, 02, 03 or 04. AT+MBFUN has lower priority vs AT+DATACUT command. If AT+DATACUT command is configured, AT+MBFUN will be ignore.

804

805

* AT+MBFUN=0: Disable Modbus fast reading.

Example:

* AT+MBFUN=1 and AT+DATACUT1/AT+DATACUT2 are not configure (0,0,0).

810

* AT+COMMAND1= 01 03 00 10 00 08,1 ~-~-> read slave address 01 , function code 03, start address 00 01, quantity of registers 00 08.

811

* AT+COMMAND2= 01 02 00 40 00 10,1 ~-~-> read slave address 01 , function code 02, start address 00 40, quantity of inputs 00 10.

812

813

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.png]]

814

815

816

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image026.png]]

* Downlink Commands:

A9 aa -à Same as AT+MBFUN=aa

822

823

824

==== RS485 command timeout ====

825

826

Some Modbus device has slow action to send replies. This command is used to configure the RS485-BL to use longer time to wait for their action.

827

828

Default value: 0, range: 0 ~~ 5 seconds

* AT Command:

AT+CMDDLaa=hex(bb cc)

Example:

**AT+CMDDL1=1000** to send the open time to 1000ms

* Downlink Payload:

0x AA aa bb cc

Same as: AT+CMDDLaa=hex(bb cc)

Example:

0xAA 01 03 E8 à Same as **AT+CMDDL1=1000 ms**

849

850

851

==== [[Uplink>>path:#downlink_A8]] payload mode ====

852

853

Define to use one uplink or multiple uplinks for the sampling.

854

855

The use of this command please see: [[Compose Uplink payload>>path:#DataUP]]

* AT Command:

AT+DATAUP=0

AT+DATAUP=1

* Downlink Payload:

0xAD 00 à Same as AT+DATAUP=0

867

868

0xAD 01 à Same as AT+DATAUP=1

869

870

871

==== Manually trigger an Uplink ====

872

873

Ask device to send an uplink immediately.

* Downlink Payload:

0x08 FF, RS485-BL will immediately send an uplink.

878

879

880

==== Clear RS485 Command ====

881

882

The AT+COMMANDx and AT+DATACUTx settings are stored in special location, user can use below command to clear them.

* AT Command:

**AT+CMDEAR=mm,nn** mm: start position of erase ,nn: stop position of erase

888

889

Etc. AT+CMDEAR=1,10 means erase AT+COMMAND1/AT+DATACUT1 to AT+COMMAND10/AT+DATACUT10

890

891

Example screen shot after clear all RS485 commands.

The uplink screen shot is:

896

897

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

* Downlink Payload:

0x09 aa bb same as AT+CMDEAR=aa,bb

903

904

905

==== Set Serial Communication Parameters ====

906

907

Set the Rs485 serial communication parameters:

* AT Command:

Set Baud Rate:

AT+BAUDR=9600 ~/~/ Options: (1200,2400,4800,14400,19200,115200)

Set UART parity

AT+PARITY=0 ~/~/ Option: 0: no parity, 1: odd parity, 2: even parity

Set STOPBIT

AT+STOPBIT=0 ~/~/ Option: 0 for 1bit; 1 for 1.5 bit ; 2 for 2 bits

* Downlink Payload:

A7 01 aa bb: Same AT+BAUDR=hex(aa bb)*100

Example:

* A7 01 00 60 same as AT+BAUDR=9600

933

* A7 01 04 80 same as AT+BAUDR=115200

934

935

A7 02 aa: Same as AT+PARITY=aa (aa value: 00 , 01 or 02)

936

937

A7 03 aa: Same as AT+STOPBIT=aa (aa value: 00 , 01 or 02)

938

939

940

==== Control output power duration ====

941

942

User can set the output power duration before each sampling.

* AT Command:

Example:

AT+3V3T=1000 ~/~/ 3V3 output power will open 1s before each sampling.

949

950

AT+5VT=1000 ~/~/ +5V output power will open 1s before each sampling.

951

952

953

* LoRaWAN Downlink Command:

954

955

07 01 aa bb Same as AT+5VT=(aa bb)

956

957

07 02 aa bb Same as AT+3V3T=(aa bb)

1.

11. Buttons

|**Button**|**Feature**

966

|**RST**|Reboot RS485-BL

1.

11. +3V3 Output

RS485-BL has a Controllable +3V3 output, user can use this output to power external sensor.

972

973

The +3V3 output will be valid for every sampling. RS485-BL will enable +3V3 output before all sampling and disable the +3V3 after all sampling.

974

975

976

The +3V3 output time can be controlled by AT Command.

**AT+3V3T=1000**

Means set +3v3 valid time to have 1000ms. So, the real +3v3 output will actually have 1000ms + sampling time for other sensors.

981

982

983

By default, the AT+3V3T=0. This is a special case, means the +3V3 output is always on at any time

1.

11. +5V Output

RS485-BL has a Controllable +5V output, user can use this output to power external sensor.

990

991

The +5V output will be valid for every sampling. RS485-BL will enable +5V output before all sampling and disable the +5v after all sampling.

992

993

994

The 5V output time can be controlled by AT Command.

**AT+5VT=1000**

Means set 5V valid time to have 1000ms. So, the real 5V output will actually have 1000ms + sampling time for other sensors.

999

1000

1001

By default, the AT+5VT=0. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.

1.

11. LEDs

|**LEDs**|**Feature**

1010

|**LED1**|Blink when device transmit a packet.

1.

11. Switch Jumper

|**Switch Jumper**|**Feature**

1016

|**SW1**|(((

1017

ISP position: Upgrade firmware via UART

1018

1019

Flash position: Configure device, check running status.

1020

)))

1021

|**SW2**|(((

1022

5V position: set to compatible with 5v I/O.

1023

1024

3.3v position: set to compatible with 3.3v I/O.,

)))

+3.3V: is always ON

+5V: Only open before every sampling. The time is by default, it is AT+5VT=0. Max open time. 5000 ms.

1. Case Study

User can check this URL for some case studies.

1034

1035

[[http:~~/~~/wiki.dragino.com/index.php?title=APP_RS485_COMMUNICATE_WITH_SENSORS>>url:http://wiki.dragino.com/index.php?title=APP_RS485_COMMUNICATE_WITH_SENSORS]]

1. Use AT Command

11. Access AT Command

1042

1043

RS485-BL supports AT Command set. User can use a USB to TTL adapter plus the 3.5mm Program Cable to connect to RS485-BL to use AT command, as below.

1044

1045

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image027.png]]

1046

1047

1048

In PC, User needs to set **serial tool**(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to **9600** to access to access serial console of RS485-BL. The default password is 123456. Below is the output for reference:

1049

1050

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image028.png]]

More detail AT Command manual can be found at [[AT Command Manual>>path:#AT_COMMAND]]

1.

11. Common AT Command Sequence

1060

111. Multi-channel ABP mode (Use with SX1301/LG308)

1061

1062

If device has not joined network yet:

AT+FDR

AT+NJM=0

ATZ

If device already joined network:

AT+NJM=0

ATZ

1.

11.

111. Single-channel ABP mode (Use with LG01/LG02)

1080

1081

AT+FDR Reset Parameters to Factory Default, Keys Reserve

1082

1083

AT+NJM=0 Set to ABP mode

1084

1085

AT+ADR=0 Set the Adaptive Data Rate Off

1086

1087

AT+DR=5 Set Data Rate

1088

1089

AT+TDC=60000 Set transmit interval to 60 seconds

1090

1091

AT+CHS=868400000 Set transmit frequency to 868.4Mhz

1092

1093

AT+RX2FQ=868400000 Set RX2Frequency to 868.4Mhz (according to the result from server)

1094

1095

AT+RX2DR=5 Set RX2DR to match the downlink DR from server. see below

1096

1097

AT+DADDR=26 01 1A F1 Set Device Address to 26 01 1A F1, this ID can be found in the LoRa Server portal.

ATZ Reset MCU

**Note:**

1. Make sure the device is set to ABP mode in the IoT Server.

1104

1. Make sure the LG01/02 gateway RX frequency is exactly the same as AT+CHS setting.

1105

1. Make sure SF / bandwidth setting in LG01/LG02 match the settings of AT+DR. refer [[this link>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/&file=LoRaWAN%201.0.3%20Regional%20Parameters.xlsx]] to see what DR means.

1106

1. The command AT+RX2FQ and AT+RX2DR is to let downlink work. to set the correct parameters, user can check the actually downlink parameters to be used. As below. Which shows the RX2FQ should use 868400000 and RX2DR should be 5

1107

1108

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]

1. FAQ

11. How to upgrade the image?

1113

1114

The RS485-BL LoRaWAN Controller is shipped with a 3.5mm cable, the cable is used to upload image to RS485-BL to:

1115

1116

* Support new features

1117

* For bug fix

1118

* Change LoRaWAN bands.

1119

1120

Below shows the hardware connection for how to upload an image to RS485-BL:

1121

1122

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]]

1123

1124

**Step1:** Download [[flash loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].

1125

1126

**Step2**: Download the [[LT Image files>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/image/]].

1127

1128

**Step3: **Open flashloader; choose the correct COM port to update.

|(((

HOLD PRO then press the RST button, SYS will be ON, then click next

)))

|(((

Board detected

)))

|(((

)))

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image032.png]]

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.png]]

1148

1149

1150

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image035.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]]

1.

11. How to change the LoRa Frequency Bands/Region?

1155

1156

User can follow the introduction for [[how to upgrade image>>path:#upgrade_image]]. When download the images, choose the required image file for download.

1.

11. How many RS485-Slave can RS485-BL connects?

1162

1163

The RS485-BL can support max 32 RS485 devices. Each uplink command of RS485-BL can support max 16 different RS485 command. So RS485-BL can support max 16 RS485 devices pre-program in the device for uplink. For other devices no pre-program, user can use the [[downlink message (type code 0xA8) to poll their info>>path:#downlink_A8]].

1. Trouble Shooting

11. Downlink doesn’t work, how to solve it?

1170

1171

Please see this link for debug:

1172

1173

[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#LoRaWAN_Communication_Debug>>url:http://wiki.dragino.com/index.php?title=Main_Page#LoRaWAN_Communication_Debug]]

1.

11. Why I can’t join TTN V3 in US915 /AU915 bands?

1179

1180

It might about the channels mapping. Please see for detail.

1181

1182

[[http:~~/~~/wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band>>url:http://wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band]]

1. Order Info

**Part Number: RS485-BL-XXX**

**XXX:**

* **EU433**: frequency bands EU433

1193

* **EU868**: frequency bands EU868

1194

* **KR920**: frequency bands KR920

1195

* **CN470**: frequency bands CN470

1196

* **AS923**: frequency bands AS923

1197

* **AU915**: frequency bands AU915

1198

* **US915**: frequency bands US915

1199

* **IN865**: frequency bands IN865

1200

* **RU864**: frequency bands RU864

1201

* **KZ865: **frequency bands KZ865

1. Packing Info

**Package Includes**:

1206

1207

* RS485-BL x 1

1208

* Stick Antenna for LoRa RF part x 1

1209

* Program cable x 1

1210

1211

**Dimension and weight**:

1212

1213

* Device Size: 13.5 x 7 x 3 cm

1214

* Device Weight: 105g

1215

* Package Size / pcs : 14.5 x 8 x 5 cm

1216

* Weight / pcs : 170g

1. Support

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1221

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to

1222

1223

[[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]

Wiki source code of RS485-LN – RS485 to LoRaWAN Converter

Applications

Navigation