RS485-BL – Waterproof RS485 to LoRaWAN Converter

The Dragino RS485-BL is a **RS485 / UART to LoRaWAN Converter** for Internet of Things solutions. User can connect RS485 or UART sensor to RS485-BL converter, and configure RS485-BL to periodically read sensor data and upload via LoRaWAN network to IoT server.

26

)))

27

28

(((

29

RS485-BL can interface to RS485 sensor, 3.3v/5v UART sensor or interrupt sensor. RS485-BL provides **a 3.3v output** and** a 5v output** to power external sensors. Both output voltages are controllable to minimize the total system power consumption.

)))

(((

RS485-BL is IP67 **waterproof** and powered by **8500mAh Li-SOCI2 battery**, it is designed for long term use for several years.

)))

(((

RS485-BL runs standard **LoRaWAN 1.0.3 in Class A**. It can reach long transfer range and easy to integrate with LoRaWAN compatible gateway and IoT server.

)))

(((

For data uplink, RS485-BL sends user-defined commands to RS485 devices and gets the return from the RS485 devices. RS485-BL will process these returns data according to user-define rules to get the final payload and upload to LoRaWAN server.

)))

(((

For data downlink, RS485-BL runs in LoRaWAN Class A. When there is downlink commands from LoRaWAN server, RS485-BL will forward the commands from LoRaWAN server to RS485 devices.

)))

(((

Each RS485-BL pre-load with a set of unique keys for LoRaWAN registration, register these keys to LoRaWAN server and it will auto connect after power on.

50

)))

51

52

[[image:1652953304999-717.png||height="424" width="733"]]

53

54

== 1.2 Specifications ==

**Hardware System:**

* STM32L072CZT6 MCU

* SX1276/78 Wireless Chip

60

* Power Consumption (exclude RS485 device):

** Idle: 6uA@3.3v

*

** 20dB Transmit: 130mA@3.3v

65

66

**Interface for Model:**

67

68

* 1 x RS485 Interface

69

* 1 x TTL Serial , 3.3v or 5v.

70

* 1 x I2C Interface, 3.3v or 5v.

71

* 1 x one wire interface

72

* 1 x Interrupt Interface

73

* 1 x Controllable 5V output, max

**LoRa Spec:**

* Frequency Range:

** Band 1 (HF): 862 ~~ 1020 Mhz

79

** Band 2 (LF): 410 ~~ 528 Mhz

80

* 168 dB maximum link budget.

81

* +20 dBm - 100 mW constant RF output vs.

82

* Programmable bit rate up to 300 kbps.

83

* High sensitivity: down to -148 dBm.

84

* Bullet-proof front end: IIP3 = -12.5 dBm.

85

* Excellent blocking immunity.

86

* Fully integrated synthesizer with a resolution of 61 Hz.

87

* LoRa modulation.

88

* Built-in bit synchronizer for clock recovery.

89

* Preamble detection.

90

* 127 dB Dynamic Range RSSI.

91

* Automatic RF Sense and CAD with ultra-fast AFC.

== 1.3 Features ==

* LoRaWAN Class A & Class C protocol (default Class A)

96

* Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865/RU864

97

* AT Commands to change parameters

98

* Remote configure parameters via LoRaWAN Downlink

99

* Firmware upgradable via program port

100

* Support multiply RS485 devices by flexible rules

101

* Support Modbus protocol

102

* Support Interrupt uplink

103

104

== 1.4 Applications ==

105

106

* Smart Buildings & Home Automation

107

* Logistics and Supply Chain Management

* Smart Metering

* Smart Agriculture

* Smart Cities

* Smart Factory

== 1.5 Firmware Change log ==

114

115

[[RS485-BL Image files – Download link and Change log>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/RS485-BL/Firmware/||style="background-color: rgb(255, 255, 255);"]]

116

117

== 1.6 Hardware Change log ==

(((

v1.4

)))

(((

~1. Change Power IC to TPS22916

)))

(((

v1.3

)))

(((

~1. Change JP3 from KF350-8P to KF350-11P, Add one extra interface for I2C and one extra interface for one-wire

)))

(((

v1.2

)))

(((

Release version

)))

= 2. Pin mapping and Power ON Device =

146

147

(((

148

The RS485-BL is powered on by 8500mAh battery. To save battery life, RS485-BL is shipped with power off. User can put the jumper to power on RS485-BL.

149

)))

150

151

[[image:1652953055962-143.png||height="387" width="728"]]

152

153

154

The Left TXD and RXD are TTL interface for external sensor. TTL level is controlled by 3.3/5v Jumper.

155

156

= 3. Operation Mode =

157

158

== 3.1 How it works? ==

159

160

(((

161

The RS485-BL is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join network. To connect a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the RS485-BL. It will auto join the network via OTAA.

162

)))

163

164

== 3.2 Example to join LoRaWAN network ==

165

166

Here shows an example for how to join the TTN V3 Network. Below is the network structure, we use [[LG308>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/140-lg308.html]] as LoRaWAN gateway here.

167

168

[[image:1652953414711-647.png||height="337" width="723"]]

169

170

(((

171

The RS485-BL in this example connected to two RS485 devices for demonstration, user can connect to other RS485 devices via the same method.

)))

(((

The LG308 is already set to connect to [[TTN V3 network >>url:https://www.thethingsnetwork.org/]]. So what we need to now is only configure the TTN V3:

)))

(((

**Step 1**: Create a device in TTN V3 with the OTAA keys from RS485-BL.

)))

(((

Each RS485-BL is shipped with a sticker with unique device EUI:

184

)))

185

186

[[image:1652953462722-299.png]]

187

188

(((

189

User can enter this key in their LoRaWAN Server portal. Below is TTN V3 screen shot:

)))

(((

Add APP EUI in the application.

)))

[[image:image-20220519174512-1.png]]

200

201

[[image:image-20220519174512-2.png||height="328" width="731"]]

202

203

[[image:image-20220519174512-3.png||height="556" width="724"]]

204

205

[[image:image-20220519174512-4.png]]

206

207

You can also choose to create the device manually.

208

209

[[image:1652953542269-423.png||height="710" width="723"]]

210

211

Add APP KEY and DEV EUI

212

213

[[image:1652953553383-907.png||height="514" width="724"]]

(((

**Step 2**: Power on RS485-BL and it will auto join to the TTN V3 network. After join success, it will start to upload message to TTN V3 and user can see in the panel.

218

)))

219

220

[[image:1652953568895-172.png||height="232" width="724"]]

221

222

== 3.3 Configure Commands to read data ==

223

224

(((

225

There are plenty of RS485 and TTL level devices in the market and each device has different command to read the valid data. To support these devices in flexible, RS485-BL supports flexible command set. User can use [[AT Commands or LoRaWAN Downlink>>path:#AT_COMMAND]] Command to configure how RS485-BL should read the sensor and how to handle the return from RS485 or TTL sensors.

226

)))

227

228

=== 3.3.1 onfigure UART settings for RS485 or TTL communication ===

229

230

RS485-BL can connect to either RS485 sensors or TTL sensor. User need to specify what type of sensor need to connect.

231

232

**~1. RS485-MODBUS mode:**

233

234

AT+MOD=1 ~/~/ Support RS485-MODBUS type sensors. User can connect multiply RS485 , Modbus sensors to the A / B pins.

**2. TTL mode:**

AT+MOD=2 ~/~/ Support TTL Level sensors, User can connect one TTL Sensor to the TXD/RXD/GND pins.

239

240

RS485-BL default UART settings is **9600, no parity, stop bit 1**. If the sensor has a different settings, user can change the RS485-BL setting to match.

241

242

(% border="1" style="background-color:#ffffcc; color:green; width:795px" %)

243

|(((

244

**AT Commands**

245

)))|(% style="width:285px" %)(((

246

**Description**

247

)))|(% style="width:347px" %)(((

**Example**

)))

|(((

AT+BAUDR

)))|(% style="width:285px" %)(((

253

Set the baud rate (for RS485 connection). Default Value is: 9600.

254

)))|(% style="width:347px" %)(((

(((

AT+BAUDR=9600

)))

(((

Options: (1200,2400,4800,14400,19200,115200)

)))

)))

|(((

AT+PARITY

)))|(% style="width:285px" %)(((

266

(((

267

Set UART parity (for RS485 connection)

)))

(((

Default Value is: no parity.

272

)))

273

)))|(% style="width:347px" %)(((

(((

AT+PARITY=0

)))

(((

Option: 0: no parity, 1: odd parity, 2: even parity

)))

)))

|(((

AT+STOPBIT

)))|(% style="width:285px" %)(((

285

(((

286

Set serial stopbit (for RS485 connection)

)))

(((

Default Value is: 1bit.

291

)))

292

)))|(% style="width:347px" %)(((

293

(((

294

AT+STOPBIT=0 for 1bit

)))

(((

AT+STOPBIT=1 for 1.5 bit

)))

(((

AT+STOPBIT=2 for 2 bits

)))

)))

1.

11.

111. Configure sensors

312

313

Some sensors might need to configure before normal operation. User can configure such sensor via PC or through RS485-BL AT Commands AT+CFGDEV.

314

315

316

When user issue an AT+CFGDEV command, Each AT+CFGDEV equals to send a command to the RS485 or TTL sensors. This command will only run when user input it and won’t run during each sampling.

317

318

|**AT Commands**|**Description**|**Example**

319

|AT+CFGDEV|(((

320

This command is used to configure the RS485/TTL devices; they won’t be used during sampling.

321

322

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

323

324

m: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command

325

)))|AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

326

327

Detail of AT+CFGDEV command see [[AT+CFGDEV detail>>path:#AT_CFGDEV]].

1.

11.

111. Configure read commands for each sampling

336

337

RS485-BL is a battery powered device; it will sleep most of time. And wake up on each period and read RS485 / TTL sensor data and uplink.

338

339

340

During each sampling, we need to confirm what commands we need to send to the sensors to read data. After the RS485/TTL sensors send back the value, it normally includes some bytes and we only need a few from them for a shorten payload.

341

342

343

To save the LoRaWAN network bandwidth, we might need to read data from different sensors and combine their valid value into a short payload.

344

345

346

This section describes how to achieve above goals.

347

348

349

During each sampling, the RS485-BL can support 15 commands to read sensors. And combine the return to one or several uplink payloads.

350

351

352

**Command from RS485-BL to Sensor:**

353

354

RS485-BL can send out pre-set max 15 strings via **AT+COMMAD1**, **ATCOMMAND2**,…, to **AT+COMMANDF** . All commands are of same grammar.

355

356

357

**Handle return from sensors to RS485-BL**:

358

359

After RS485-BL send out a string to sensor, RS485-BL will wait for the return from RS485 or TTL sensor. And user can specify how to handle the return, by **AT+DATACUT or AT+SEARCH commands**

* **AT+DATACUT**

When the return value from sensor have fix length and we know which position the valid value we should get, we can use AT+DATACUT command.

* **AT+SEARCH**

When the return value from sensor is dynamic length and we are not sure which bytes the valid data is, instead, we know what value the valid value following. We can use AT+SEARCH to search the valid value in the return string.

370

371

372

**Define wait timeout:**

373

374

Some RS485 device might has longer delay on reply, so user can use AT+CMDDL to set the timeout for getting reply after the RS485 command is sent. For example, AT+CMDDL1=1000 to send the open time to 1000ms

375

376

377

After we got the valid value from each RS485 commands, we need to combine them together with the command **AT+DATAUP**.

**Examples:**

Below are examples for the how above AT Commands works.

383

384

385

**AT+COMMANDx : **This command will be sent to RS485/TTL devices during each sampling, Max command length is 14 bytes. The grammar is:

386

387

|(((

388

**AT+COMMANDx=xx xx xx xx xx xx xx xx xx xx xx xx,m**

389

390

**xx xx xx xx xx xx xx xx xx xx xx xx: The RS485 command to be sent**

391

392

**m: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command**

393

)))

394

395

For example, if we have a RS485 sensor. The command to get sensor value is: 01 03 0B B8 00 02 46 0A. Where 01 03 0B B8 00 02 is the Modbus command to read the register 0B B8 where stored the sensor value. The 46 0A is the CRC-16/MODBUS which calculate manually.

396

397

In the RS485-BL, we should use this command AT+COMMAND1=01 03 0B B8 00 02,1 for the same.

398

399

400

**AT+SEARCHx**: This command defines how to handle the return from AT+COMMANDx.

401

402

|(((

403

**AT+SEARCHx=aa,xx xx xx xx xx**

404

405

* **aa: 1: prefix match mode; 2: prefix and suffix match mode**

406

* **xx xx xx xx xx: match string. Max 5 bytes for prefix and 5 bytes for suffix**

)))

Examples:

1. For a return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

414

415

If we set AT+SEARCH1=1,1E 56 34. (max 5 bytes for prefix)

416

417

The valid data will be all bytes after 1E 56 34 , so it is 2e 30 58 5f 36 41 30 31 00 49

418

419

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image013.png]]

420

421

422

1. For a return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

423

424

If we set AT+SEARCH1=2, 1E 56 34+31 00 49

425

426

Device will search the bytes between 1E 56 34 and 31 00 49. So it is 2e 30 58 5f 36 41 30

427

428

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image014.png]]

429

430

431

**AT+DATACUTx : **This command defines how to handle the return from AT+COMMANDx, max return length is 45 bytes.

432

433

|(((

434

**AT+DATACUTx=a,b,c**

435

436

* **a: length for the return of AT+COMMAND**

437

* **b:1: grab valid value by byte, max 6 bytes. 2: grab valid value by bytes section, max 3 sections.**

438

* **c: define the position for valid value. **

)))

Examples:

* Grab bytes:

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.png]]

* Grab a section.

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image016.png]]

450

451

* Grab different sections.

452

453

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.png]]

Note:

AT+SEARCHx and AT+DATACUTx can be used together, if both commands are set, RS485-BL will first process AT+SEARCHx on the return string and get a temporary string, and then process AT+DATACUTx on this temporary string to get the final payload. In this case, AT+DATACUTx need to set to format AT+DATACUTx=0,xx,xx where the return bytes set to 0.

Example:

AT+COMMAND1=11 01 1E D0,0

463

464

AT+SEARCH1=1,1E 56 34

AT+DATACUT1=0,2,1~~5

Return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49

469

470

String after SEARCH command: 2e 30 58 5f 36 41 30 31 00 49

471

472

Valid payload after DataCUT command: 2e 30 58 5f 36

473

474

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image018.png]]

1.

11.

111. Compose the uplink payload

482

483

Through AT+COMMANDx and AT+DATACUTx we got valid value from each RS485 commands, Assume these valid value are RETURN1, RETURN2, .., to RETURNx. The next step is how to compose the LoRa Uplink Payload by these RETURNs. The command is **AT+DATAUP.**

484

485

486

**Examples: AT+DATAUP=0**

487

488

Compose the uplink payload with value returns in sequence and send with **A SIGNLE UPLINK**.

Final Payload is

Battery Info+PAYVER + VALID Value from RETURN1 + Valid Value from RETURN2 + … + RETURNx

493

494

Where PAYVER is defined by AT+PAYVER, below is an example screen shot.

495

496

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image019.png]]

**Examples: AT+DATAUP=1**

501

502

Compose the uplink payload with value returns in sequence and send with **Multiply UPLINKs**.

Final Payload is

Battery Info+PAYVER + PAYLOAD COUNT + PAYLOAD# + DATA

507

508

1. Battery Info (2 bytes): Battery voltage

509

1. PAYVER (1 byte): Defined by AT+PAYVER

510

1. PAYLOAD COUNT (1 byte): Total how many uplinks of this sampling.

511

1. PAYLOAD# (1 byte): Number of this uplink. (from 0,1,2,3…,to PAYLOAD COUNT)

512

1. DATA: Valid value: max 6 bytes(US915 version here, [[Notice*!>>path:#max_byte]]) for each uplink so each uplink <= 11 bytes. For the last uplink, DATA will might less than 6 bytes

513

514

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image020.png]]

515

516

517

So totally there will be 3 uplinks for this sampling, each uplink includes 6 bytes DATA

518

519

DATA1=RETURN1 Valid Value = 20 20 0a 33 90 41

520

521

DATA2=1^^st^^ ~~ 6^^th^^ byte of Valid value of RETURN10= 02 aa 05 81 0a 20

522

523

DATA3=7^^th^^ ~~ 11^^th^^ bytes of Valid value of RETURN10 = 20 20 20 2d 30

Below are the uplink payloads:

528

529

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]]

530

531

532

Notice: the Max bytes is according to the max support bytes in different Frequency Bands for lowest SF. As below:

533

534

~* For AU915/AS923 bands, if UplinkDwell time=0, max 51 bytes for each uplink ( so 51 -5 = 46 max valid date)

535

536

* For AU915/AS923 bands, if UplinkDwell time=1, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

537

538

* For US915 band, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

539

540

~* For all other bands: max 51 bytes for each uplink ( so 51 -5 = 46 max valid date).

1.

11.

111. Uplink on demand

547

548

Except uplink periodically, RS485-BL is able to uplink on demand. The server sends downlink command to RS485-BL and RS485 will uplink data base on the command.

549

550

Downlink control command:

551

552

[[0x08 command>>path:#downlink_08]]: Poll an uplink with current command set in RS485-BL.

553

554

[[0xA8 command>>path:#downlink_A8]]: Send a command to RS485-BL and uplink the output from sensors.

1.

11.

111. Uplink on Interrupt

561

562

Put the interrupt sensor between 3.3v_out and GPIO ext.[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]]

563

564

AT+INTMOD=0 Disable Interrupt

565

566

AT+INTMOD=1 Interrupt trigger by rising or falling edge.

567

568

AT+INTMOD=2 Interrupt trigger by falling edge. ( Default Value)

569

570

AT+INTMOD=3 Interrupt trigger by rising edge.

1.

11. Uplink Payload

|**Size(bytes)**|**2**|**1**|**Length depends on the return from the commands**

|Value|(((

Battery(mV)

&

Interrupt _Flag

)))|(((

PAYLOAD_VER

)))|If the valid payload is too long and exceed the maximum support payload length in server, server will show payload not provided in the LoRaWAN server.

588

589

Below is the decoder for the first 3 bytes. The rest bytes are dynamic depends on different RS485 sensors.

590

591

592

function Decoder(bytes, port) {

593

594

~/~/Payload Formats of RS485-BL Deceive

return {

~/~/Battery,units:V

BatV:((bytes[0]<<8 | bytes[1])&0x7fff)/1000,

~/~/GPIO_EXTI

EXTI_Trigger:(bytes[0] & 0x80)? "TRUE":"FALSE",

605

606

~/~/payload of version

Pay_ver:bytes[2],

};

}

TTN V3 uplink screen shot.

621

622

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

623

624

1.

625

11. Configure RS485-BL via AT or Downlink

626

627

User can configure RS485-BL via [[AT Commands >>path:#_Using_the_AT]]or LoRaWAN Downlink Commands

628

629

There are two kinds of Commands:

630

631

* **Common Commands**: They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands

632

633

* **Sensor Related Commands**: These commands are special designed for RS485-BL. User can see these commands below:

1.

11.

111. Common Commands:

638

639

They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: [[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands>>url:http://wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands]]

1.

11.

111. Sensor related commands:

645

646

==== Choose Device Type (RS485 or TTL) ====

647

648

RS485-BL can connect to either RS485 sensors or TTL sensor. User need to specify what type of sensor need to connect.

* AT Command

**AT+MOD=1** ~/~/ Set to support RS485-MODBUS type sensors. User can connect multiply RS485 , Modbus sensors to the A / B pins.

653

654

**AT+MOD=2** ~/~/ Set to support TTL Level sensors, User can connect one TTL Sensor to the TXD/RXD/GND pins.

* Downlink Payload

**0A aa** à same as AT+MOD=aa

==== [[RS485 Debug Command>>path:#downlink_A8]] (AT+CFGDEV) ====

664

665

This command is used to configure the RS485 or TTL sensors; they won’t be used during sampling.

* AT Command

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

670

671

m: 0: no CRC; 1: add CRC-16/MODBUS in the end of this command.

* Downlink Payload

Format: A8 MM NN XX XX XX XX YY

Where:

* MM: 1: add CRC-16/MODBUS ; 0: no CRC

682

* NN: The length of RS485 command

683

* XX XX XX XX: RS485 command total NN bytes

684

* YY: How many bytes will be uplink from the return of this RS485 command, if YY=0, RS485-BL will execute the downlink command without uplink; if YY>0, RS485-BL will uplink total YY bytes from the output of this RS485 command

**Example 1:**

To connect a Modbus Alarm with below commands.

689

690

* The command to active alarm is: 0A 05 00 04 00 01 4C B0. Where 0A 05 00 04 00 01 is the Modbus command to read the register 00 40 where stored the DI status. The 4C B0 is the CRC-16/MODBUS which calculate manually.

691

692

* The command to deactivate alarm is: 0A 05 00 04 00 00 8D 70. Where 0A 05 00 04 00 00 is the Modbus command to read the register 00 40 where stored the DI status. The 8D 70 is the CRC-16/MODBUS which calculate manually.

693

694

So if user want to use downlink command to control to RS485 Alarm, he can use:

695

696

**A8 01 06 0A 05 00 04 00 01 00**: to activate the RS485 Alarm

697

698

**A8 01 06 0A 05 00 04 00 00 00**: to deactivate the RS485 Alarm

699

700

A8 is type code and 01 means add CRC-16/MODBUS at the end, the 3^^rd^^ byte is 06, means the next 6 bytes are the command to be sent to the RS485 network, the final byte 00 means this command don’t need to acquire output.

**Example 2:**

Check TTL Sensor return:

706

707

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image024.png]]

==== Set Payload version ====

713

714

This is the first byte of the uplink payload. RS485-BL can connect to different sensors. User can set the PAYVER field to tell server how to decode the current payload.

* AT Command:

AT+PAYVER: Set PAYVER field = 1

* Downlink Payload:

0xAE 01 à Set PAYVER field = 0x01

724

725

0xAE 0F à Set PAYVER field = 0x0F

726

727

728

==== Set RS485 Sampling Commands ====

729

730

AT+COMMANDx, AT+DATACUTx and AT+SEARCHx

731

732

These three commands are used to configure how the RS485-BL polling data from Modbus device. Detail of usage please see : [[polling RS485 device>>path:#polling_485]].

* AT Command:

AT+COMMANDx: Configure RS485 read command to sensor.

738

739

AT+DATACUTx: Configure how to handle return from RS485 devices.

740

741

AT+SEARCHx: Configure search command

* Downlink Payload:

0xAF downlink command can be used to set AT+COMMANDx or AT+DATACUTx.

747

748

Note: if user use AT+COMMANDx to add a new command, he also need to send AT+DATACUTx downlink.

749

750

Format: AF MM NN LL XX XX XX XX YY

Where:

* MM: the ATCOMMAND or AT+DATACUT to be set. Value from 01 ~~ 0F,

755

* NN: 0: no CRC; 1: add CRC-16/MODBUS ; 2: set the AT+DATACUT value.

756

* LL: The length of AT+COMMAND or AT+DATACUT command

757

* XX XX XX XX: AT+COMMAND or AT+DATACUT command

758

* YY: If YY=0, RS485-BL will execute the downlink command without uplink; if YY=1, RS485-BL will execute an uplink after got this command.

Example:

**AF 03 01 06 0A 05 00 04 00 01 00**: Same as AT+COMMAND3=0A 05 00 04 00 01,1

763

764

**AF 03 02 06 10 01 05 06 09 0A 00**: Same as AT+DATACUT3=**16**,**1**,**5+6+9+10**

765

766

**AF 03 02 06 0B 02 05 07 08 0A 00**: Same as AT+DATACUT3=**11**,**2**,**5~~7+8~~10**

767

768

769

0xAB downlink command can be used for set AT+SEARCHx

770

771

Example: **AB aa 01 03 xx xx xx** (03 here means there are total 3 bytes after 03) So

772

773

* AB aa 01 03 xx xx xx same as AT+SEARCHaa=1,xx xx xx

774

* AB aa 02 03 xx xx xx 02 yy yy(03 means there are 3 bytes after 03, they are xx xx xx;02 means there are 2 bytes after 02, they are yy yy) so the commands

775

776

**AB aa 02 03 xx xx xx 02 yy yy** same as **AT+SEARCHaa=2,xx xx xx+yy yy**

777

778

779

==== Fast command to handle MODBUS device ====

780

781

AT+MBFUN is valid since v1.3 firmware version. The command is for fast configure to read Modbus devices. It is only valid for the devices which follow the [[MODBUS-RTU protocol>>url:https://www.modbustools.com/modbus.html]].

782

783

This command is valid since v1.3 firmware version

784

785

786

AT+MBFUN has only two value:

787

788

* AT+MBFUN=1: Enable Modbus reading. And get response base on the MODBUS return

789

790

AT+MBFUN=1, device can auto read the Modbus function code: 01, 02, 03 or 04. AT+MBFUN has lower priority vs AT+DATACUT command. If AT+DATACUT command is configured, AT+MBFUN will be ignore.

791

792

* AT+MBFUN=0: Disable Modbus fast reading.

Example:

* AT+MBFUN=1 and AT+DATACUT1/AT+DATACUT2 are not configure (0,0,0).

797

* AT+COMMAND1= 01 03 00 10 00 08,1 ~-~-> read slave address 01 , function code 03, start address 00 01, quantity of registers 00 08.

798

* AT+COMMAND2= 01 02 00 40 00 10,1 ~-~-> read slave address 01 , function code 02, start address 00 40, quantity of inputs 00 10.

799

800

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.png]]

801

802

803

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image026.png]]

* Downlink Commands:

A9 aa -à Same as AT+MBFUN=aa

809

810

811

==== RS485 command timeout ====

812

813

Some Modbus device has slow action to send replies. This command is used to configure the RS485-BL to use longer time to wait for their action.

814

815

Default value: 0, range: 0 ~~ 5 seconds

* AT Command:

AT+CMDDLaa=hex(bb cc)

Example:

**AT+CMDDL1=1000** to send the open time to 1000ms

* Downlink Payload:

0x AA aa bb cc

Same as: AT+CMDDLaa=hex(bb cc)

Example:

0xAA 01 03 E8 à Same as **AT+CMDDL1=1000 ms**

836

837

838

==== [[Uplink>>path:#downlink_A8]] payload mode ====

839

840

Define to use one uplink or multiple uplinks for the sampling.

841

842

The use of this command please see: [[Compose Uplink payload>>path:#DataUP]]

* AT Command:

AT+DATAUP=0

AT+DATAUP=1

* Downlink Payload:

0xAD 00 à Same as AT+DATAUP=0

854

855

0xAD 01 à Same as AT+DATAUP=1

856

857

858

==== Manually trigger an Uplink ====

859

860

Ask device to send an uplink immediately.

* Downlink Payload:

0x08 FF, RS485-BL will immediately send an uplink.

865

866

867

==== Clear RS485 Command ====

868

869

The AT+COMMANDx and AT+DATACUTx settings are stored in special location, user can use below command to clear them.

* AT Command:

**AT+CMDEAR=mm,nn** mm: start position of erase ,nn: stop position of erase

875

876

Etc. AT+CMDEAR=1,10 means erase AT+COMMAND1/AT+DATACUT1 to AT+COMMAND10/AT+DATACUT10

877

878

Example screen shot after clear all RS485 commands.

The uplink screen shot is:

883

884

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

* Downlink Payload:

0x09 aa bb same as AT+CMDEAR=aa,bb

890

891

892

==== Set Serial Communication Parameters ====

893

894

Set the Rs485 serial communication parameters:

* AT Command:

Set Baud Rate:

AT+BAUDR=9600 ~/~/ Options: (1200,2400,4800,14400,19200,115200)

Set UART parity

AT+PARITY=0 ~/~/ Option: 0: no parity, 1: odd parity, 2: even parity

Set STOPBIT

AT+STOPBIT=0 ~/~/ Option: 0 for 1bit; 1 for 1.5 bit ; 2 for 2 bits

* Downlink Payload:

A7 01 aa bb: Same AT+BAUDR=hex(aa bb)*100

Example:

* A7 01 00 60 same as AT+BAUDR=9600

920

* A7 01 04 80 same as AT+BAUDR=115200

921

922

A7 02 aa: Same as AT+PARITY=aa (aa value: 00 , 01 or 02)

923

924

A7 03 aa: Same as AT+STOPBIT=aa (aa value: 00 , 01 or 02)

925

926

927

==== Control output power duration ====

928

929

User can set the output power duration before each sampling.

* AT Command:

Example:

AT+3V3T=1000 ~/~/ 3V3 output power will open 1s before each sampling.

936

937

AT+5VT=1000 ~/~/ +5V output power will open 1s before each sampling.

938

939

940

* LoRaWAN Downlink Command:

941

942

07 01 aa bb Same as AT+5VT=(aa bb)

943

944

07 02 aa bb Same as AT+3V3T=(aa bb)

1.

11. Buttons

|**Button**|**Feature**

953

|**RST**|Reboot RS485-BL

1.

11. +3V3 Output

RS485-BL has a Controllable +3V3 output, user can use this output to power external sensor.

959

960

The +3V3 output will be valid for every sampling. RS485-BL will enable +3V3 output before all sampling and disable the +3V3 after all sampling.

961

962

963

The +3V3 output time can be controlled by AT Command.

**AT+3V3T=1000**

Means set +3v3 valid time to have 1000ms. So, the real +3v3 output will actually have 1000ms + sampling time for other sensors.

968

969

970

By default, the AT+3V3T=0. This is a special case, means the +3V3 output is always on at any time

1.

11. +5V Output

RS485-BL has a Controllable +5V output, user can use this output to power external sensor.

977

978

The +5V output will be valid for every sampling. RS485-BL will enable +5V output before all sampling and disable the +5v after all sampling.

979

980

981

The 5V output time can be controlled by AT Command.

**AT+5VT=1000**

Means set 5V valid time to have 1000ms. So, the real 5V output will actually have 1000ms + sampling time for other sensors.

986

987

988

By default, the AT+5VT=0. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.

1.

11. LEDs

|**LEDs**|**Feature**

997

|**LED1**|Blink when device transmit a packet.

1.

11. Switch Jumper

|**Switch Jumper**|**Feature**

1003

|**SW1**|(((

1004

ISP position: Upgrade firmware via UART

1005

1006

Flash position: Configure device, check running status.

1007

)))

1008

|**SW2**|(((

1009

5V position: set to compatible with 5v I/O.

1010

1011

3.3v position: set to compatible with 3.3v I/O.,

)))

+3.3V: is always ON

+5V: Only open before every sampling. The time is by default, it is AT+5VT=0. Max open time. 5000 ms.

1. Case Study

User can check this URL for some case studies.

1021

1022

[[http:~~/~~/wiki.dragino.com/index.php?title=APP_RS485_COMMUNICATE_WITH_SENSORS>>url:http://wiki.dragino.com/index.php?title=APP_RS485_COMMUNICATE_WITH_SENSORS]]

1. Use AT Command

11. Access AT Command

1029

1030

RS485-BL supports AT Command set. User can use a USB to TTL adapter plus the 3.5mm Program Cable to connect to RS485-BL to use AT command, as below.

1031

1032

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image027.png]]

1033

1034

1035

In PC, User needs to set **serial tool**(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to **9600** to access to access serial console of RS485-BL. The default password is 123456. Below is the output for reference:

1036

1037

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image028.png]]

More detail AT Command manual can be found at [[AT Command Manual>>path:#AT_COMMAND]]

1.

11. Common AT Command Sequence

1047

111. Multi-channel ABP mode (Use with SX1301/LG308)

1048

1049

If device has not joined network yet:

AT+FDR

AT+NJM=0

ATZ

If device already joined network:

AT+NJM=0

ATZ

1.

11.

111. Single-channel ABP mode (Use with LG01/LG02)

1067

1068

AT+FDR Reset Parameters to Factory Default, Keys Reserve

1069

1070

AT+NJM=0 Set to ABP mode

1071

1072

AT+ADR=0 Set the Adaptive Data Rate Off

1073

1074

AT+DR=5 Set Data Rate

1075

1076

AT+TDC=60000 Set transmit interval to 60 seconds

1077

1078

AT+CHS=868400000 Set transmit frequency to 868.4Mhz

1079

1080

AT+RX2FQ=868400000 Set RX2Frequency to 868.4Mhz (according to the result from server)

1081

1082

AT+RX2DR=5 Set RX2DR to match the downlink DR from server. see below

1083

1084

AT+DADDR=26 01 1A F1 Set Device Address to 26 01 1A F1, this ID can be found in the LoRa Server portal.

ATZ Reset MCU

**Note:**

1. Make sure the device is set to ABP mode in the IoT Server.

1091

1. Make sure the LG01/02 gateway RX frequency is exactly the same as AT+CHS setting.

1092

1. Make sure SF / bandwidth setting in LG01/LG02 match the settings of AT+DR. refer [[this link>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/&file=LoRaWAN%201.0.3%20Regional%20Parameters.xlsx]] to see what DR means.

1093

1. The command AT+RX2FQ and AT+RX2DR is to let downlink work. to set the correct parameters, user can check the actually downlink parameters to be used. As below. Which shows the RX2FQ should use 868400000 and RX2DR should be 5

1094

1095

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]

1. FAQ

11. How to upgrade the image?

1100

1101

The RS485-BL LoRaWAN Controller is shipped with a 3.5mm cable, the cable is used to upload image to RS485-BL to:

1102

1103

* Support new features

1104

* For bug fix

1105

* Change LoRaWAN bands.

1106

1107

Below shows the hardware connection for how to upload an image to RS485-BL:

1108

1109

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]]

1110

1111

**Step1:** Download [[flash loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].

1112

1113

**Step2**: Download the [[LT Image files>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/image/]].

1114

1115

**Step3: **Open flashloader; choose the correct COM port to update.

|(((

HOLD PRO then press the RST button, SYS will be ON, then click next

)))

|(((

Board detected

)))

|(((

)))

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image032.png]]

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.png]]

1135

1136

1137

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image035.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]]

1.

11. How to change the LoRa Frequency Bands/Region?

1142

1143

User can follow the introduction for [[how to upgrade image>>path:#upgrade_image]]. When download the images, choose the required image file for download.

1.

11. How many RS485-Slave can RS485-BL connects?

1149

1150

The RS485-BL can support max 32 RS485 devices. Each uplink command of RS485-BL can support max 16 different RS485 command. So RS485-BL can support max 16 RS485 devices pre-program in the device for uplink. For other devices no pre-program, user can use the [[downlink message (type code 0xA8) to poll their info>>path:#downlink_A8]].

1. Trouble Shooting

11. Downlink doesn’t work, how to solve it?

1157

1158

Please see this link for debug:

1159

1160

[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#LoRaWAN_Communication_Debug>>url:http://wiki.dragino.com/index.php?title=Main_Page#LoRaWAN_Communication_Debug]]

1.

11. Why I can’t join TTN V3 in US915 /AU915 bands?

1166

1167

It might about the channels mapping. Please see for detail.

1168

1169

[[http:~~/~~/wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band>>url:http://wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band]]

1. Order Info

**Part Number: RS485-BL-XXX**

**XXX:**

* **EU433**: frequency bands EU433

1180

* **EU868**: frequency bands EU868

1181

* **KR920**: frequency bands KR920

1182

* **CN470**: frequency bands CN470

1183

* **AS923**: frequency bands AS923

1184

* **AU915**: frequency bands AU915

1185

* **US915**: frequency bands US915

1186

* **IN865**: frequency bands IN865

1187

* **RU864**: frequency bands RU864

1188

* **KZ865: **frequency bands KZ865

1. Packing Info

**Package Includes**:

1193

1194

* RS485-BL x 1

1195

* Stick Antenna for LoRa RF part x 1

1196

* Program cable x 1

1197

1198

**Dimension and weight**:

1199

1200

* Device Size: 13.5 x 7 x 3 cm

1201

* Device Weight: 105g

1202

* Package Size / pcs : 14.5 x 8 x 5 cm

1203

* Weight / pcs : 170g

1. Support

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1208

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to

1209

1210

[[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]

Wiki source code of RS485-BL – Waterproof RS485 to LoRaWAN Converter

Applications

Navigation