Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -831,6 +831,7 @@
831	831
832	832
833	833
	834	+
834	834	==== **RS485 command timeout** ====
835	835
836	836	(((
...	...	@@ -886,6 +886,7 @@
886	886
887	887
888	888
	890	+
889	889	==== **Uplink payload mode** ====
890	890
891	891	(((
...	...	@@ -935,90 +935,163 @@
935	935
936	936	==== **Manually trigger an Uplink** ====
937	937
	940	+(((
938	938	Ask device to send an uplink immediately.
	942	+)))
939	939
940		-* **AT Command:**
	944	+* (((
	945	+**AT Command:**
	946	+)))
941	941
	948	+(((
942	942	No AT Command for this, user can press the [[ACT button>>||anchor="H3.7Buttons"]] for 1 second for the same.
	950	+)))
943	943
	952	+(((
	953	+
	954	+)))
944	944
945		-* **Downlink Payload:**
	956	+* (((
	957	+**Downlink Payload:**
	958	+)))
946	946
	960	+(((
947	947	**0x08 FF**, RS485-LN will immediately send an uplink.
	962	+)))
948	948
949	949
950	950
	966	+
951	951	==== **Clear RS485 Command** ====
952	952
	969	+(((
953	953	The AT+COMMANDx and AT+DATACUTx settings are stored in special location, user can use below command to clear them.
	971	+)))
954	954
955		-* **AT Command:**
	973	+* (((
	974	+**AT Command:**
	975	+)))
956	956
	977	+(((
957	957	**AT+CMDEAR=mm,nn**   mm: start position of erase ,nn: stop position of erase
	979	+)))
958	958
	981	+(((
959	959	Etc. AT+CMDEAR=1,10 means erase AT+COMMAND1/AT+DATACUT1 to AT+COMMAND10/AT+DATACUT10
	983	+)))
960	960
	985	+(((
961	961	Example screen shot after clear all RS485 commands.
	987	+)))
962	962
	989	+(((
	990	+
	991	+)))
963	963
	993	+(((
964	964	The uplink screen shot is:
	995	+)))
965	965
966	966	[[image:1654160691922-496.png]]
967	967
968	968
969		-* **Downlink Payload:**
	1000	+* (((
	1001	+**Downlink Payload:**
	1002	+)))
970	970
	1004	+(((
971	971	**0x09 aa bb** same as AT+CMDEAR=aa,bb
	1006	+)))
972	972
973	973
974	974
	1010	+
975	975	==== **Set Serial Communication Parameters** ====
976	976
	1013	+(((
977	977	Set the Rs485 serial communication parameters:
	1015	+)))
978	978
979		-* **AT Command:**
	1017	+* (((
	1018	+**AT Command:**
	1019	+)))
980	980
	1021	+(((
981	981	Set Baud Rate:
	1023	+)))
982	982
983	983	(% class="box infomessage" %)
984	984	(((
	1027	+(((
985	985	**AT+BAUDR=9600**    ~/~/ Options: (1200,2400,4800,14400,19200,115200)
986	986	)))
	1030	+)))
987	987
	1032	+(((
988	988	Set UART Parity
	1034	+)))
989	989
990	990	(% class="box infomessage" %)
991	991	(((
	1038	+(((
992	992	**AT+PARITY=0**    ~/~/ Option: 0: no parity, 1: odd parity, 2: even parity
993	993	)))
	1041	+)))
994	994
	1043	+(((
995	995	Set STOPBIT
	1045	+)))
996	996
997	997	(% class="box infomessage" %)
998	998	(((
	1049	+(((
999	999	**AT+STOPBIT=0**    ~/~/ Option: 0 for 1bit; 1 for 1.5 bit ; 2 for 2 bits
1000	1000	)))
	1052	+)))
1001	1001
	1054	+(((
	1055	+
	1056	+)))
1002	1002
1003		-* **Downlink Payload:**
	1058	+* (((
	1059	+**Downlink Payload:**
	1060	+)))
1004	1004
	1062	+(((
1005	1005	**A7 01 aa bb**: Same  AT+BAUDR=hex(aa bb)*100
	1064	+)))
1006	1006
	1066	+(((
1007	1007	**Example:**
	1068	+)))
1008	1008
1009		-* A7 01 00 60   same as AT+BAUDR=9600
1010		-* A7 01 04 80  same as AT+BAUDR=115200
	1070	+* (((
	1071	+A7 01 00 60   same as AT+BAUDR=9600
	1072	+)))
	1073	+* (((
	1074	+A7 01 04 80  same as AT+BAUDR=115200
	1075	+)))
1011	1011
	1077	+(((
1012	1012	A7 02 aa: Same as  AT+PARITY=aa  (aa value: 00 , 01 or 02)
	1079	+)))
1013	1013
	1081	+(((
1014	1014	A7 03 aa: Same as  AT+STOPBIT=aa  (aa value: 00 , 01 or 02)
	1083	+)))
1015	1015
1016	1016
	1086	+
	1087	+
1017	1017	== 3.6 Listening mode for RS485 network ==
1018	1018
	1090	+(((
1019	1019	This feature support since firmware v1.4
	1092	+)))
1020	1020
	1094	+(((
1021	1021	RS485-LN supports listening mode, it can listen the RS485 network packets and send them via LoRaWAN uplink. Below is the structure. The blue arrow shows the RS485 network packets to RS485-LN.
	1096	+)))
1022	1022
1023	1023	[[image:image-20220602171200-8.png||height="567" width="1007"]]
1024	1024