Last modified by Karry Zhuang on 2025/03/06 16:34
<
From version < 32.17 >
edited by Xiaoling
on 2022/06/02 15:31
To version < 35.2 >
edited by Xiaoling
on 2022/06/02 15:44
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -290,6 +290,7 @@
290 290  )))
291 291  
292 292  
293 +
293 293  === 3.3.2 Configure sensors ===
294 294  
295 295  (((
... ... @@ -313,77 +313,36 @@
313 313  === 3.3.3 Configure read commands for each sampling ===
314 314  
315 315  (((
316 -RS485-BL is a battery powered device; it will sleep most of time. And wake up on each period and read RS485 / TTL sensor data and uplink.
317 -)))
317 +During each sampling, we need confirm what commands we need to send to the RS485 sensors to read data. After the RS485 sensors send back the value, it normally include some bytes and we only need a few from them for a shorten payload.
318 318  
319 -(((
320 -During each sampling, we need to confirm what commands we need to send to the sensors to read data. After the RS485/TTL sensors send back the value, it normally includes some bytes and we only need a few from them for a shorten payload.
321 -)))
322 -
323 -(((
324 324  To save the LoRaWAN network bandwidth, we might need to read data from different sensors and combine their valid value into a short payload.
325 -)))
326 326  
327 -(((
328 328  This section describes how to achieve above goals.
329 -)))
330 330  
331 -(((
332 -During each sampling, the RS485-BL can support 15 commands to read sensors. And combine the return to one or several uplink payloads.
333 -)))
323 +During each sampling, the RS485-LN can support 15 commands to read sensors. And combine the return to one or several uplink payloads.
334 334  
335 -(((
336 -**Command from RS485-BL to Sensor:**
337 -)))
338 338  
339 -(((
340 -RS485-BL can send out pre-set max 15 strings via **AT+COMMAD1**, **ATCOMMAND2**,…, to **AT+COMMANDF** . All commands are of same grammar.
341 -)))
326 +**Each RS485 commands include two parts:**
342 342  
343 -(((
344 -**Handle return from sensors to RS485-BL**:
345 -)))
328 +~1. What commands RS485-LN will send to the RS485 sensors. There are total 15 commands from **AT+COMMAD1**, **ATCOMMAND2**,…, to **AT+COMMANDF**. All commands are of same grammar.
346 346  
347 -(((
348 -After RS485-BL send out a string to sensor, RS485-BL will wait for the return from RS485 or TTL sensor. And user can specify how to handle the return, by **AT+DATACUT or AT+SEARCH commands**
349 -)))
330 +2. How to get wanted value the from RS485 sensors returns from by 1). There are total 15 AT Commands to handle the return, commands are **AT+DATACUT1**,**AT+DATACUT2**,…, **AT+DATACUTF** corresponding to the commands from 1). All commands are of same grammar.
350 350  
351 -* (((
352 -**AT+DATACUT**
353 -)))
332 +3. Some RS485 device might has longer delay on reply, so user can use AT+CMDDL to set the timeout for getting reply after the RS485 command is sent. For example
354 354  
355 -(((
356 -When the return value from sensor have fix length and we know which position the valid value we should get, we can use AT+DATACUT command.
357 -)))
334 +**AT+CMDDL1=1000** to send the open time to 1000ms
358 358  
359 -* (((
360 -**AT+SEARCH**
361 -)))
362 362  
363 -(((
364 -When the return value from sensor is dynamic length and we are not sure which bytes the valid data is, instead, we know what value the valid value following. We can use AT+SEARCH to search the valid value in the return string.
365 -)))
366 -
367 -(((
368 -**Define wait timeout:**
369 -)))
370 -
371 -(((
372 -Some RS485 device might has longer delay on reply, so user can use AT+CMDDL to set the timeout for getting reply after the RS485 command is sent. For example, AT+CMDDL1=1000 to send the open time to 1000ms
373 -)))
374 -
375 -(((
376 376  After we got the valid value from each RS485 commands, we need to combine them together with the command **AT+DATAUP**.
377 -)))
378 378  
379 -**Examples:**
380 380  
381 381  Below are examples for the how above AT Commands works.
382 382  
383 -**AT+COMMANDx : **This command will be sent to RS485/TTL devices during each sampling, Max command length is 14 bytes. The grammar is:
384 384  
385 -(% border="1" class="table-bordered" %)
386 -|(((
343 +**AT+COMMANDx : **This command will be sent to RS485 devices during each sampling, Max command length is 14 bytes. The grammar is:
344 +
345 +(% border="1" style="background-color:#4bacc6; color:white; width:499px" %)
346 +|(% style="width:496px" %)(((
387 387  **AT+COMMANDx=xx xx xx xx xx xx xx xx xx xx xx xx,m**
388 388  
389 389  **xx xx xx xx xx xx xx xx xx xx xx xx: The RS485 command to be sent**
... ... @@ -391,90 +391,40 @@
391 391  **m: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command**
392 392  )))
393 393  
394 -(((
395 395  For example, if we have a RS485 sensor. The command to get sensor value is: 01 03 0B B8 00 02 46 0A. Where 01 03 0B B8 00 02 is the Modbus command to read the register 0B B8 where stored the sensor value. The 46 0A is the CRC-16/MODBUS which calculate manually.
396 -)))
397 397  
398 -(((
399 -In the RS485-BL, we should use this command AT+COMMAND1=01 03 0B B8 00 02,1 for the same.
400 -)))
356 +In the RS485-LN, we should use this command AT+COMMAND1=01 03 0B B8 00 02,1 for the same.
401 401  
402 -(((
403 -**AT+SEARCHx**: This command defines how to handle the return from AT+COMMANDx.
404 -)))
405 405  
406 -(% border="1" class="table-bordered" %)
407 -|(((
408 -**AT+SEARCHx=aa,xx xx xx xx xx**
409 -
410 -* **aa: 1: prefix match mode; 2: prefix and suffix match mode**
411 -* **xx xx xx xx xx: match string. Max 5 bytes for prefix and 5 bytes for suffix**
412 -
413 -
414 -)))
415 -
416 -**Examples:**
417 -
418 -~1. For a return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49
419 -
420 -If we set AT+SEARCH1=1,1E 56 34.      (max 5 bytes for prefix)
421 -
422 -The valid data will be all bytes after 1E 56 34 , so it is (% style="background-color:yellow" %)** 2e 30 58 5f 36 41 30 31 00 49**
423 -
424 -[[image:1653269403619-508.png]]
425 -
426 -2. For a return string from AT+COMMAND1:  16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49
427 -
428 -If we set AT+SEARCH1=2, 1E 56 34+31 00 49
429 -
430 -Device will search the bytes between 1E 56 34 and 31 00 49. So it is (% style="background-color:yellow" %)** 2e 30 58 5f 36 41 30**
431 -
432 -[[image:1653269438444-278.png]]
433 -
434 434  **AT+DATACUTx : **This command defines how to handle the return from AT+COMMANDx, max return length is 45 bytes.
435 435  
436 -|(((
361 +(% border="1" style="background-color:#4bacc6; color:white; width:725px" %)
362 +|(% style="width:722px" %)(((
437 437  **AT+DATACUTx=a,b,c**
438 438  
439 439  * **a: length for the return of AT+COMMAND**
440 440  * **b:1: grab valid value by byte, max 6 bytes. 2: grab valid value by bytes section, max 3 sections.**
441 -* **c: define the position for valid value.  **
367 +* **c: define the position for valid value. **
442 442  )))
443 443  
444 -Examples:
445 445  
371 +**Examples:**
372 +
446 446  * Grab bytes:
447 447  
448 -[[image:1653269551753-223.png||height="311" width="717"]]
375 +[[image:image-20220602153621-1.png]]
449 449  
377 +
450 450  * Grab a section.
451 451  
452 -[[image:1653269568276-930.png||height="325" width="718"]]
380 +[[image:image-20220602153621-2.png]]
453 453  
382 +
454 454  * Grab different sections.
455 455  
456 -[[image:1653269593172-426.png||height="303" width="725"]]
385 +[[image:image-20220602153621-3.png]]
386 +)))
457 457  
458 -(% style="color:red" %)**Note:**
459 -
460 -AT+SEARCHx and AT+DATACUTx can be used together, if both commands are set, RS485-BL will first process AT+SEARCHx on the return string and get a temporary string, and then process AT+DATACUTx on this temporary string to get the final payload. In this case, AT+DATACUTx need to set to format AT+DATACUTx=0,xx,xx where the return bytes set to 0.
461 -
462 -Example:
463 -
464 -(% style="color:red" %)AT+COMMAND1=11 01 1E D0,0
465 -
466 -(% style="color:red" %)AT+SEARCH1=1,1E 56 34
467 -
468 -(% style="color:red" %)AT+DATACUT1=0,2,1~~5
469 -
470 -(% style="color:red" %)Return string from AT+COMMAND1: 16 0c 1e 56 34 2e 30 58 5f 36 41 30 31 00 49
471 -
472 -(% style="color:red" %)String after SEARCH command: 2e 30 58 5f 36 41 30 31 00 49
473 -
474 -(% style="color:red" %)Valid payload after DataCUT command: 2e 30 58 5f 36
475 -
476 -[[image:1653269618463-608.png]]
477 -
478 478  === 3.3.4 Compose the uplink payload ===
479 479  
480 480  (((
image-20220602153621-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +23.4 KB
Content
image-20220602153621-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +22.2 KB
Content
image-20220602153621-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +22.3 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0