RS485-LN – RS485 to LoRaWAN Converter

The Dragino RS485-LN is a (% style="color:blue" %)**RS485 to LoRaWAN Converter**(%%). It converts the RS485 signal into LoRaWAN wireless signal which simplify the IoT installation and reduce the installation/maintaining cost.

22

)))

23

24

(((

25

RS485-LN allows user to (% style="color:blue" %)**monitor / control RS485 devices**(%%) and reach extremely long ranges. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption. It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on.

)))

(((

(% style="color:blue" %)**For data uplink**(%%), RS485-LN sends user-defined commands to RS485 devices and gets the return from the RS485 devices. RS485-LN will process these returns according to user-define rules to get the final payload and upload to LoRaWAN server.

)))

(((

(% style="color:blue" %)**For data downlink**(%%), RS485-LN runs in LoRaWAN Class C. When there downlink commands from LoRaWAN server, RS485-LN will forward the commands from LoRaWAN server to RS485 devices.

34

35

(% style="color:blue" %)**Demo Dashboard for RS485-LN**(%%) connect to two energy meters: [[https:~~/~~/app.datacake.de/dashboard/d/58844a26-378d-4c5a-aaf5-b5b5b153447a>>url:https://app.datacake.de/dashboard/d/58844a26-378d-4c5a-aaf5-b5b5b153447a]]

)))

)))

[[image:1653267211009-519.png||height="419" width="724"]]

40

41

42

== 1.2 Specifications ==

**Hardware System:**

* STM32L072CZT6 MCU

* SX1276/78 Wireless Chip

49

* Power Consumption (exclude RS485 device):

50

** Idle: 32mA@12v

51

** 20dB Transmit: 65mA@12v

52

53

**Interface for Model:**

54

55

* RS485

56

* Power Input 7~~ 24V DC.

**LoRa Spec:**

* Frequency Range:

** Band 1 (HF): 862 ~~ 1020 Mhz

62

** Band 2 (LF): 410 ~~ 528 Mhz

63

* 168 dB maximum link budget.

64

* +20 dBm - 100 mW constant RF output vs.

65

* +14 dBm high efficiency PA.

66

* Programmable bit rate up to 300 kbps.

67

* High sensitivity: down to -148 dBm.

68

* Bullet-proof front end: IIP3 = -12.5 dBm.

69

* Excellent blocking immunity.

70

* Low RX current of 10.3 mA, 200 nA register retention.

71

* Fully integrated synthesizer with a resolution of 61 Hz.

72

* FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.

73

* Built-in bit synchronizer for clock recovery.

74

* Preamble detection.

75

* 127 dB Dynamic Range RSSI.

76

* Automatic RF Sense and CAD with ultra-fast AFC.

77

* Packet engine up to 256 bytes with CRC.

== 1.3 Features ==

* LoRaWAN Class A & Class C protocol (default Class C)

82

* Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865/RU864

83

* AT Commands to change parameters

84

* Remote configure parameters via LoRa Downlink

85

* Firmware upgradable via program port

86

* Support multiply RS485 devices by flexible rules

87

* Support Modbus protocol

88

* Support Interrupt uplink (Since hardware version v1.2)

89

90

== 1.4 Applications ==

91

92

* Smart Buildings & Home Automation

93

* Logistics and Supply Chain Management

* Smart Metering

* Smart Agriculture

* Smart Cities

* Smart Factory

== 1.5 Firmware Change log ==

100

101

[[RS485-LN Image files – Download link and Change log>>url:http://www.dragino.com/downloads/index.php?dir=RS485-LN/]]

102

103

104

== 1.6 Hardware Change log ==

(((

(((

v1.2: Add External Interrupt Pin.

v1.0: Release

)))

)))

= 2. Power ON Device =

117

118

(((

119

The RS485-LN can be powered by 7 ~~ 24V DC power source. Connection as below

120

121

* Power Source VIN to RS485-LN VIN+

122

* Power Source GND to RS485-LN VIN-

123

124

(((

125

Once there is power, the RS485-LN will be on.

126

)))

127

128

[[image:1653268091319-405.png]]

)))

= 3. Operation Mode =

134

135

== 3.1 How it works? ==

136

137

(((

138

The RS485-LN is configured as LoRaWAN OTAA Class C mode by default. It has OTAA keys to join network. To connect a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the RS485-LN. It will auto join the network via OTAA.

)))

== 3.2 Example to join LoRaWAN network ==

144

145

Here shows an example for how to join the TTN V3 Network. Below is the network structure, we use [[LG308>>url:http://www.dragino.com/products/lora-lorawan-gateway/item/140-lg308.html]] as LoRaWAN gateway here.

146

147

[[image:1653268155545-638.png||height="334" width="724"]]

(((

(((

The RS485-LN in this example connected to two RS485 devices for demonstration, user can connect to other RS485 devices via the same method. The connection is as below:

)))

(((

485A+ and 485B- of the sensor are connected to RS485A and RA485B of RS485-LN respectively.

157

)))

158

159

[[image:1653268227651-549.png||height="592" width="720"]]

160

161

(((

162

The LG308 is already set to connect to [[TTN V3 network >>path:eu1.cloud.thethings.network/]]. So what we need to now is only configure the TTN V3:

)))

(((

**Step 1**: Create a device in TTN V3 with the OTAA keys from RS485-LN.

)))

(((

Each RS485-LN is shipped with a sticker with unique device EUI:

)))

)))

[[image:1652953462722-299.png]]

(((

(((

User can enter this key in their LoRaWAN Server portal. Below is TTN V3 screen shot:

)))

(((

Add APP EUI in the application.

)))

)))

[[image:image-20220519174512-1.png]]

187

188

[[image:image-20220519174512-2.png||height="323" width="720"]]

189

190

[[image:image-20220519174512-3.png||height="556" width="724"]]

191

192

[[image:image-20220519174512-4.png]]

193

194

You can also choose to create the device manually.

195

196

[[image:1652953542269-423.png||height="710" width="723"]]

197

198

Add APP KEY and DEV EUI

199

200

[[image:1652953553383-907.png||height="514" width="724"]]

(((

**Step 2**: Power on RS485-LN and it will auto join to the TTN V3 network. After join success, it will start to upload message to TTN V3 and user can see in the panel.

205

)))

206

207

[[image:1652953568895-172.png||height="232" width="724"]]

208

209

210

== 3.3 Configure Commands to read data ==

(((

(((

There are plenty of RS485 devices in the market and each device has different command to read the valid data. To support these devices in flexible, RS485-LN supports flexible command set. User can use [[AT Commands>>path:#AT_COMMAND]] or LoRaWAN Downlink Command to configure what commands RS485-LN should send for each sampling and how to handle the return from RS485 devices.

)))

(((

(% style="color:red" %)Note: below description and commands are for firmware version >v1.1, if you have firmware version v1.0. Please check the [[user manual v1.0>>url:http://www.dragino.com/downloads/index.php?dir=RS485-LN/&file=RS485-LN_UserManual_v1.0.1.pdf]] or upgrade the firmware to v1.1

)))

)))

=== 3.3.1 onfigure UART settings for RS485 or TTL communication ===

225

226

To use RS485-LN to read data from RS485 sensors, connect the RS485-LN A/B traces to the sensors. And user need to make sure RS485-LN use the match UART setting to access the sensors. The related commands for UART settings are:

227

228

(% border="1" style="background-color:#ffffcc; color:green; width:782px" %)

229

|(% style="width:128px" %)(((

230

**AT Commands**

231

)))|(% style="width:305px" %)(((

232

**Description**

233

)))|(% style="width:346px" %)(((

234

**Example**

235

)))

236

|(% style="width:128px" %)(((

237

AT+BAUDR

238

)))|(% style="width:305px" %)(((

239

Set the baud rate (for RS485 connection). Default Value is: 9600.

240

)))|(% style="width:346px" %)(((

(((

AT+BAUDR=9600

)))

(((

Options: (1200,2400,4800,14400,19200,115200)

247

)))

248

)))

249

|(% style="width:128px" %)(((

250

AT+PARITY

251

)))|(% style="width:305px" %)(((

252

Set UART parity (for RS485 connection)

253

)))|(% style="width:346px" %)(((

(((

AT+PARITY=0

)))

(((

Option: 0: no parity, 1: odd parity, 2: even parity

260

)))

261

)))

262

|(% style="width:128px" %)(((

263

AT+STOPBIT

264

)))|(% style="width:305px" %)(((

265

(((

266

Set serial stopbit (for RS485 connection)

)))

(((

)))

)))|(% style="width:346px" %)(((

273

(((

274

AT+STOPBIT=0 for 1bit

)))

(((

AT+STOPBIT=1 for 1.5 bit

)))

(((

AT+STOPBIT=2 for 2 bits

)))

)))

=== 3.3.2 Configure sensors ===

(((

(((

Some sensors might need to configure before normal operation. User can configure such sensor via PC and RS485 adapter or through RS485-LN AT Commands (% style="color:#4f81bd" %)**AT+CFGDEV**(%%). Each (% style="color:#4f81bd" %)**AT+CFGDEV **(%%)equals to send a RS485 command to sensors. This command will only run when user input it and won’t run during each sampling.

)))

)))

(% border="1" style="background-color:#ffffcc; color:green; width:806px" %)

295

|**AT Commands**|(% style="width:418px" %)**Description**|(% style="width:256px" %)**Example**

296

|AT+CFGDEV|(% style="width:418px" %)(((

297

This command is used to configure the RS485/TTL devices; they won’t be used during sampling.

298

299

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,

300

301

mm: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command

302

)))|(% style="width:256px" %)AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

303

304

=== 3.3.3 Configure read commands for each sampling ===

305

306

(((

307

During each sampling, we need confirm what commands we need to send to the RS485 sensors to read data. After the RS485 sensors send back the value, it normally include some bytes and we only need a few from them for a shorten payload.

308

309

To save the LoRaWAN network bandwidth, we might need to read data from different sensors and combine their valid value into a short payload.

310

311

This section describes how to achieve above goals.

312

313

During each sampling, the RS485-LN can support 15 commands to read sensors. And combine the return to one or several uplink payloads.

314

315

316

**Each RS485 commands include two parts:**

317

318

~1. What commands RS485-LN will send to the RS485 sensors. There are total 15 commands from **AT+COMMAD1**, **ATCOMMAND2**,…, to **AT+COMMANDF**. All commands are of same grammar.

319

320

2. How to get wanted value the from RS485 sensors returns from by 1). There are total 15 AT Commands to handle the return, commands are **AT+DATACUT1**,**AT+DATACUT2**,…, **AT+DATACUTF** corresponding to the commands from 1). All commands are of same grammar.

321

322

3. Some RS485 device might has longer delay on reply, so user can use AT+CMDDL to set the timeout for getting reply after the RS485 command is sent. For example **AT+CMDDL1=1000** to send the open time to 1000ms

323

324

325

After we got the valid value from each RS485 commands, we need to combine them together with the command **AT+DATAUP**.

326

327

328

Below are examples for the how above AT Commands works.

329

330

331

**AT+COMMANDx : **This command will be sent to RS485 devices during each sampling, Max command length is 14 bytes. The grammar is:

332

333

(% border="1" style="background-color:#4bacc6; color:white; width:499px" %)

334

|(% style="width:496px" %)(((

335

**AT+COMMANDx=xx xx xx xx xx xx xx xx xx xx xx xx,m**

336

337

**xx xx xx xx xx xx xx xx xx xx xx xx: The RS485 command to be sent**

338

339

**m: 0: no CRC, 1: add CRC-16/MODBUS in the end of this command**

340

)))

341

342

For example, if we have a RS485 sensor. The command to get sensor value is: 01 03 0B B8 00 02 46 0A. Where 01 03 0B B8 00 02 is the Modbus command to read the register 0B B8 where stored the sensor value. The 46 0A is the CRC-16/MODBUS which calculate manually.

343

344

In the RS485-LN, we should use this command AT+COMMAND1=01 03 0B B8 00 02,1 for the same.

345

346

347

**AT+DATACUTx : **This command defines how to handle the return from AT+COMMANDx, max return length is 45 bytes.

348

349

(% border="1" style="background-color:#4bacc6; color:white; width:725px" %)

350

|(% style="width:722px" %)(((

351

**AT+DATACUTx=a,b,c**

352

353

* **a: length for the return of AT+COMMAND**

354

* **b:1: grab valid value by byte, max 6 bytes. 2: grab valid value by bytes section, max 3 sections.**

355

* **c: define the position for valid value. **

)))

**Examples:**

* Grab bytes:

[[image:image-20220602153621-1.png]]

* Grab a section.

[[image:image-20220602153621-2.png]]

368

369

370

* Grab different sections.

371

372

[[image:image-20220602153621-3.png]]

)))

=== 3.3.4 Compose the uplink payload ===

378

379

(((

380

Through AT+COMMANDx and AT+DATACUTx we got valid value from each RS485 commands, Assume these valid value are RETURN1, RETURN2, .., to RETURNx. The next step is how to compose the LoRa Uplink Payload by these RETURNs. The command is **AT+DATAUP.**

)))

(((

(% style="color:#037691" %)**Examples: AT+DATAUP=0**

)))

(((

Compose the uplink payload with value returns in sequence and send with (% style="color:red" %)**A SIGNLE UPLINK**.

)))

(((

Final Payload is

)))

(((

(% style="color:#4f81bd" %)**Battery Info+PAYVER + VALID Value from RETURN1 + Valid Value from RETURN2 + … + RETURNx**

)))

(((

Where PAYVER is defined by AT+PAYVER, below is an example screen shot.

405

)))

406

407

[[image:1653269759169-150.png||height="513" width="716"]]

408

409

410

(% style="color:#037691" %)**Examples: AT+DATAUP=1**

411

412

413

Compose the uplink payload with value returns in sequence and send with (% style="color:red" %)**Multiply UPLINKs**.

Final Payload is

(% style="color:#4f81bd" %)**Battery Info+PAYVER + PAYLOAD COUNT + PAYLOAD# + DATA**

418

419

1. Battery Info (2 bytes): Battery voltage

420

1. PAYVER (1 byte): Defined by AT+PAYVER

421

1. PAYLOAD COUNT (1 byte): Total how many uplinks of this sampling.

422

1. PAYLOAD# (1 byte): Number of this uplink. (from 0,1,2,3…,to PAYLOAD COUNT)

423

1. DATA: Valid value: max 6 bytes(US915 version here, Notice*!) for each uplink so each uplink <= 11 bytes. For the last uplink, DATA will might less than 6 bytes

424

425

[[image:1653269916228-732.png||height="433" width="711"]]

426

427

428

So totally there will be 3 uplinks for this sampling, each uplink includes 6 bytes DATA

429

430

DATA1=RETURN1 Valid Value = (% style="background-color:green; color:white" %)20 20 0a 33 90 41

431

432

DATA2=1^^st^^ ~~ 6^^th^^ byte of Valid value of RETURN10=(% style="background-color:green; color:white" %) 02 aa 05 81 0a 20

433

434

DATA3=7^^th^^ ~~ 11^^th^^ bytes of Valid value of RETURN10 = (% style="background-color:green; color:white" %)20 20 20 2d 30

435

436

Below are the uplink payloads:

437

438

[[image:1653270130359-810.png]]

439

440

441

(% style="color:red" %)**Notice: the Max bytes is according to the max support bytes in different Frequency Bands for lowest SF. As below:**

442

443

~* For AU915/AS923 bands, if UplinkDwell time=0, max 51 bytes for each uplink ( so 51 -5 = 46 max valid date)

444

445

* For AU915/AS923 bands, if UplinkDwell time=1, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

446

447

* For US915 band, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

448

449

~* For all other bands: max 51 bytes for each uplink ( so 51 -5 = 46 max valid date).

450

451

=== 3.3.5 Uplink on demand ===

452

453

Except uplink periodically, RS485-BL is able to uplink on demand. The server sends downlink command to RS485-BL and RS485 will uplink data base on the command.

454

455

Downlink control command:

456

457

[[0x08 command>>path:#downlink_08]]: Poll an uplink with current command set in RS485-BL.

458

459

[[0xA8 command>>path:#downlink_A8]]: Send a command to RS485-BL and uplink the output from sensors.

1.

11.

111. Uplink on Interrupt

466

467

Put the interrupt sensor between 3.3v_out and GPIO ext.[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]]

468

469

AT+INTMOD=0 Disable Interrupt

470

471

AT+INTMOD=1 Interrupt trigger by rising or falling edge.

472

473

AT+INTMOD=2 Interrupt trigger by falling edge. ( Default Value)

474

475

AT+INTMOD=3 Interrupt trigger by rising edge.

1.

11. Uplink Payload

|**Size(bytes)**|**2**|**1**|**Length depends on the return from the commands**

|Value|(((

Battery(mV)

&

Interrupt _Flag

)))|(((

PAYLOAD_VER

)))|If the valid payload is too long and exceed the maximum support payload length in server, server will show payload not provided in the LoRaWAN server.

493

494

Below is the decoder for the first 3 bytes. The rest bytes are dynamic depends on different RS485 sensors.

495

496

497

function Decoder(bytes, port) {

498

499

~/~/Payload Formats of RS485-BL Deceive

return {

~/~/Battery,units:V

BatV:((bytes[0]<<8 | bytes[1])&0x7fff)/1000,

~/~/GPIO_EXTI

EXTI_Trigger:(bytes[0] & 0x80)? "TRUE":"FALSE",

510

511

~/~/payload of version

Pay_ver:bytes[2],

};

}

TTN V3 uplink screen shot.

526

527

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

528

529

1.

530

11. Configure RS485-BL via AT or Downlink

531

532

User can configure RS485-BL via [[AT Commands >>path:#_Using_the_AT]]or LoRaWAN Downlink Commands

533

534

There are two kinds of Commands:

535

536

* **Common Commands**: They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands

537

538

* **Sensor Related Commands**: These commands are special designed for RS485-BL. User can see these commands below:

1.

11.

111. Common Commands:

543

544

They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.3, user can find what common commands it supports: [[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands>>url:http://wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands]]

1.

11.

111. Sensor related commands:

550

551

==== Choose Device Type (RS485 or TTL) ====

552

553

RS485-BL can connect to either RS485 sensors or TTL sensor. User need to specify what type of sensor need to connect.

* AT Command

**AT+MOD=1** ~/~/ Set to support RS485-MODBUS type sensors. User can connect multiply RS485 , Modbus sensors to the A / B pins.

558

559

**AT+MOD=2** ~/~/ Set to support TTL Level sensors, User can connect one TTL Sensor to the TXD/RXD/GND pins.

* Downlink Payload

**0A aa** à same as AT+MOD=aa

==== [[RS485 Debug Command>>path:#downlink_A8]] (AT+CFGDEV) ====

569

570

This command is used to configure the RS485 or TTL sensors; they won’t be used during sampling.

* AT Command

AT+CFGDEV=xx xx xx xx xx xx xx xx xx xx xx xx,m

575

576

m: 0: no CRC; 1: add CRC-16/MODBUS in the end of this command.

* Downlink Payload

Format: A8 MM NN XX XX XX XX YY

Where:

* MM: 1: add CRC-16/MODBUS ; 0: no CRC

587

* NN: The length of RS485 command

588

* XX XX XX XX: RS485 command total NN bytes

589

* YY: How many bytes will be uplink from the return of this RS485 command, if YY=0, RS485-BL will execute the downlink command without uplink; if YY>0, RS485-BL will uplink total YY bytes from the output of this RS485 command

**Example 1:**

To connect a Modbus Alarm with below commands.

594

595

* The command to active alarm is: 0A 05 00 04 00 01 4C B0. Where 0A 05 00 04 00 01 is the Modbus command to read the register 00 40 where stored the DI status. The 4C B0 is the CRC-16/MODBUS which calculate manually.

596

597

* The command to deactivate alarm is: 0A 05 00 04 00 00 8D 70. Where 0A 05 00 04 00 00 is the Modbus command to read the register 00 40 where stored the DI status. The 8D 70 is the CRC-16/MODBUS which calculate manually.

598

599

So if user want to use downlink command to control to RS485 Alarm, he can use:

600

601

**A8 01 06 0A 05 00 04 00 01 00**: to activate the RS485 Alarm

602

603

**A8 01 06 0A 05 00 04 00 00 00**: to deactivate the RS485 Alarm

604

605

A8 is type code and 01 means add CRC-16/MODBUS at the end, the 3^^rd^^ byte is 06, means the next 6 bytes are the command to be sent to the RS485 network, the final byte 00 means this command don’t need to acquire output.

**Example 2:**

Check TTL Sensor return:

611

612

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image024.png]]

==== Set Payload version ====

618

619

This is the first byte of the uplink payload. RS485-BL can connect to different sensors. User can set the PAYVER field to tell server how to decode the current payload.

* AT Command:

AT+PAYVER: Set PAYVER field = 1

* Downlink Payload:

0xAE 01 à Set PAYVER field = 0x01

629

630

0xAE 0F à Set PAYVER field = 0x0F

631

632

633

==== Set RS485 Sampling Commands ====

634

635

AT+COMMANDx, AT+DATACUTx and AT+SEARCHx

636

637

These three commands are used to configure how the RS485-BL polling data from Modbus device. Detail of usage please see : [[polling RS485 device>>path:#polling_485]].

* AT Command:

AT+COMMANDx: Configure RS485 read command to sensor.

643

644

AT+DATACUTx: Configure how to handle return from RS485 devices.

645

646

AT+SEARCHx: Configure search command

* Downlink Payload:

0xAF downlink command can be used to set AT+COMMANDx or AT+DATACUTx.

652

653

Note: if user use AT+COMMANDx to add a new command, he also need to send AT+DATACUTx downlink.

654

655

Format: AF MM NN LL XX XX XX XX YY

Where:

* MM: the ATCOMMAND or AT+DATACUT to be set. Value from 01 ~~ 0F,

660

* NN: 0: no CRC; 1: add CRC-16/MODBUS ; 2: set the AT+DATACUT value.

661

* LL: The length of AT+COMMAND or AT+DATACUT command

662

* XX XX XX XX: AT+COMMAND or AT+DATACUT command

663

* YY: If YY=0, RS485-BL will execute the downlink command without uplink; if YY=1, RS485-BL will execute an uplink after got this command.

Example:

**AF 03 01 06 0A 05 00 04 00 01 00**: Same as AT+COMMAND3=0A 05 00 04 00 01,1

668

669

**AF 03 02 06 10 01 05 06 09 0A 00**: Same as AT+DATACUT3=**16**,**1**,**5+6+9+10**

670

671

**AF 03 02 06 0B 02 05 07 08 0A 00**: Same as AT+DATACUT3=**11**,**2**,**5~~7+8~~10**

672

673

674

0xAB downlink command can be used for set AT+SEARCHx

675

676

Example: **AB aa 01 03 xx xx xx** (03 here means there are total 3 bytes after 03) So

677

678

* AB aa 01 03 xx xx xx same as AT+SEARCHaa=1,xx xx xx

679

* AB aa 02 03 xx xx xx 02 yy yy(03 means there are 3 bytes after 03, they are xx xx xx;02 means there are 2 bytes after 02, they are yy yy) so the commands

680

681

**AB aa 02 03 xx xx xx 02 yy yy** same as **AT+SEARCHaa=2,xx xx xx+yy yy**

682

683

684

==== Fast command to handle MODBUS device ====

685

686

AT+MBFUN is valid since v1.3 firmware version. The command is for fast configure to read Modbus devices. It is only valid for the devices which follow the [[MODBUS-RTU protocol>>url:https://www.modbustools.com/modbus.html]].

687

688

This command is valid since v1.3 firmware version

689

690

691

AT+MBFUN has only two value:

692

693

* AT+MBFUN=1: Enable Modbus reading. And get response base on the MODBUS return

694

695

AT+MBFUN=1, device can auto read the Modbus function code: 01, 02, 03 or 04. AT+MBFUN has lower priority vs AT+DATACUT command. If AT+DATACUT command is configured, AT+MBFUN will be ignore.

696

697

* AT+MBFUN=0: Disable Modbus fast reading.

Example:

* AT+MBFUN=1 and AT+DATACUT1/AT+DATACUT2 are not configure (0,0,0).

702

* AT+COMMAND1= 01 03 00 10 00 08,1 ~-~-> read slave address 01 , function code 03, start address 00 01, quantity of registers 00 08.

703

* AT+COMMAND2= 01 02 00 40 00 10,1 ~-~-> read slave address 01 , function code 02, start address 00 40, quantity of inputs 00 10.

704

705

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.png]]

706

707

708

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image026.png]]

* Downlink Commands:

A9 aa -à Same as AT+MBFUN=aa

714

715

716

==== RS485 command timeout ====

717

718

Some Modbus device has slow action to send replies. This command is used to configure the RS485-BL to use longer time to wait for their action.

719

720

Default value: 0, range: 0 ~~ 5 seconds

* AT Command:

AT+CMDDLaa=hex(bb cc)

Example:

**AT+CMDDL1=1000** to send the open time to 1000ms

* Downlink Payload:

0x AA aa bb cc

Same as: AT+CMDDLaa=hex(bb cc)

Example:

0xAA 01 03 E8 à Same as **AT+CMDDL1=1000 ms**

741

742

743

==== [[Uplink>>path:#downlink_A8]] payload mode ====

744

745

Define to use one uplink or multiple uplinks for the sampling.

746

747

The use of this command please see: [[Compose Uplink payload>>path:#DataUP]]

* AT Command:

AT+DATAUP=0

AT+DATAUP=1

* Downlink Payload:

0xAD 00 à Same as AT+DATAUP=0

759

760

0xAD 01 à Same as AT+DATAUP=1

761

762

763

==== Manually trigger an Uplink ====

764

765

Ask device to send an uplink immediately.

* Downlink Payload:

0x08 FF, RS485-BL will immediately send an uplink.

770

771

772

==== Clear RS485 Command ====

773

774

The AT+COMMANDx and AT+DATACUTx settings are stored in special location, user can use below command to clear them.

* AT Command:

**AT+CMDEAR=mm,nn** mm: start position of erase ,nn: stop position of erase

780

781

Etc. AT+CMDEAR=1,10 means erase AT+COMMAND1/AT+DATACUT1 to AT+COMMAND10/AT+DATACUT10

782

783

Example screen shot after clear all RS485 commands.

The uplink screen shot is:

788

789

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

* Downlink Payload:

0x09 aa bb same as AT+CMDEAR=aa,bb

795

796

797

==== Set Serial Communication Parameters ====

798

799

Set the Rs485 serial communication parameters:

* AT Command:

Set Baud Rate:

AT+BAUDR=9600 ~/~/ Options: (1200,2400,4800,14400,19200,115200)

Set UART parity

AT+PARITY=0 ~/~/ Option: 0: no parity, 1: odd parity, 2: even parity

Set STOPBIT

AT+STOPBIT=0 ~/~/ Option: 0 for 1bit; 1 for 1.5 bit ; 2 for 2 bits

* Downlink Payload:

A7 01 aa bb: Same AT+BAUDR=hex(aa bb)*100

Example:

* A7 01 00 60 same as AT+BAUDR=9600

825

* A7 01 04 80 same as AT+BAUDR=115200

826

827

A7 02 aa: Same as AT+PARITY=aa (aa value: 00 , 01 or 02)

828

829

A7 03 aa: Same as AT+STOPBIT=aa (aa value: 00 , 01 or 02)

830

831

832

==== Control output power duration ====

833

834

User can set the output power duration before each sampling.

* AT Command:

Example:

AT+3V3T=1000 ~/~/ 3V3 output power will open 1s before each sampling.

841

842

AT+5VT=1000 ~/~/ +5V output power will open 1s before each sampling.

843

844

845

* LoRaWAN Downlink Command:

846

847

07 01 aa bb Same as AT+5VT=(aa bb)

848

849

07 02 aa bb Same as AT+3V3T=(aa bb)

1.

11. Buttons

|**Button**|**Feature**

858

|**RST**|Reboot RS485-BL

1.

11. +3V3 Output

RS485-BL has a Controllable +3V3 output, user can use this output to power external sensor.

864

865

The +3V3 output will be valid for every sampling. RS485-BL will enable +3V3 output before all sampling and disable the +3V3 after all sampling.

866

867

868

The +3V3 output time can be controlled by AT Command.

**AT+3V3T=1000**

Means set +3v3 valid time to have 1000ms. So, the real +3v3 output will actually have 1000ms + sampling time for other sensors.

873

874

875

By default, the AT+3V3T=0. This is a special case, means the +3V3 output is always on at any time

1.

11. +5V Output

RS485-BL has a Controllable +5V output, user can use this output to power external sensor.

882

883

The +5V output will be valid for every sampling. RS485-BL will enable +5V output before all sampling and disable the +5v after all sampling.

884

885

886

The 5V output time can be controlled by AT Command.

**AT+5VT=1000**

Means set 5V valid time to have 1000ms. So, the real 5V output will actually have 1000ms + sampling time for other sensors.

891

892

893

By default, the AT+5VT=0. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.

1.

11. LEDs

|**LEDs**|**Feature**

902

|**LED1**|Blink when device transmit a packet.

1.

11. Switch Jumper

|**Switch Jumper**|**Feature**

908

|**SW1**|(((

909

ISP position: Upgrade firmware via UART

910

911

Flash position: Configure device, check running status.

912

)))

913

|**SW2**|(((

914

5V position: set to compatible with 5v I/O.

915

916

3.3v position: set to compatible with 3.3v I/O.,

)))

+3.3V: is always ON

+5V: Only open before every sampling. The time is by default, it is AT+5VT=0. Max open time. 5000 ms.

1. Case Study

User can check this URL for some case studies.

926

927

[[http:~~/~~/wiki.dragino.com/index.php?title=APP_RS485_COMMUNICATE_WITH_SENSORS>>url:http://wiki.dragino.com/index.php?title=APP_RS485_COMMUNICATE_WITH_SENSORS]]

1. Use AT Command

11. Access AT Command

934

935

RS485-BL supports AT Command set. User can use a USB to TTL adapter plus the 3.5mm Program Cable to connect to RS485-BL to use AT command, as below.

936

937

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image027.png]]

938

939

940

In PC, User needs to set **serial tool**(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to **9600** to access to access serial console of RS485-BL. The default password is 123456. Below is the output for reference:

941

942

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image028.png]]

More detail AT Command manual can be found at [[AT Command Manual>>path:#AT_COMMAND]]

1.

11. Common AT Command Sequence

952

111. Multi-channel ABP mode (Use with SX1301/LG308)

953

954

If device has not joined network yet:

AT+FDR

AT+NJM=0

ATZ

If device already joined network:

AT+NJM=0

ATZ

1.

11.

111. Single-channel ABP mode (Use with LG01/LG02)

972

973

AT+FDR Reset Parameters to Factory Default, Keys Reserve

974

975

AT+NJM=0 Set to ABP mode

976

977

AT+ADR=0 Set the Adaptive Data Rate Off

978

979

AT+DR=5 Set Data Rate

980

981

AT+TDC=60000 Set transmit interval to 60 seconds

982

983

AT+CHS=868400000 Set transmit frequency to 868.4Mhz

984

985

AT+RX2FQ=868400000 Set RX2Frequency to 868.4Mhz (according to the result from server)

986

987

AT+RX2DR=5 Set RX2DR to match the downlink DR from server. see below

988

989

AT+DADDR=26 01 1A F1 Set Device Address to 26 01 1A F1, this ID can be found in the LoRa Server portal.

ATZ Reset MCU

**Note:**

1. Make sure the device is set to ABP mode in the IoT Server.

996

1. Make sure the LG01/02 gateway RX frequency is exactly the same as AT+CHS setting.

997

1. Make sure SF / bandwidth setting in LG01/LG02 match the settings of AT+DR. refer [[this link>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/&file=LoRaWAN%201.0.3%20Regional%20Parameters.xlsx]] to see what DR means.

998

1. The command AT+RX2FQ and AT+RX2DR is to let downlink work. to set the correct parameters, user can check the actually downlink parameters to be used. As below. Which shows the RX2FQ should use 868400000 and RX2DR should be 5

999

1000

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]

1. FAQ

11. How to upgrade the image?

1005

1006

The RS485-BL LoRaWAN Controller is shipped with a 3.5mm cable, the cable is used to upload image to RS485-BL to:

1007

1008

* Support new features

1009

* For bug fix

1010

* Change LoRaWAN bands.

1011

1012

Below shows the hardware connection for how to upload an image to RS485-BL:

1013

1014

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]]

1015

1016

**Step1:** Download [[flash loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].

1017

1018

**Step2**: Download the [[LT Image files>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/image/]].

1019

1020

**Step3: **Open flashloader; choose the correct COM port to update.

|(((

HOLD PRO then press the RST button, SYS will be ON, then click next

)))

|(((

Board detected

)))

|(((

)))

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image032.png]]

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.png]]

1040

1041

1042

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image035.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]]

1.

11. How to change the LoRa Frequency Bands/Region?

1047

1048

User can follow the introduction for [[how to upgrade image>>path:#upgrade_image]]. When download the images, choose the required image file for download.

1.

11. How many RS485-Slave can RS485-BL connects?

1054

1055

The RS485-BL can support max 32 RS485 devices. Each uplink command of RS485-BL can support max 16 different RS485 command. So RS485-BL can support max 16 RS485 devices pre-program in the device for uplink. For other devices no pre-program, user can use the [[downlink message (type code 0xA8) to poll their info>>path:#downlink_A8]].

1. Trouble Shooting

11. Downlink doesn’t work, how to solve it?

1062

1063

Please see this link for debug:

1064

1065

[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#LoRaWAN_Communication_Debug>>url:http://wiki.dragino.com/index.php?title=Main_Page#LoRaWAN_Communication_Debug]]

1.

11. Why I can’t join TTN V3 in US915 /AU915 bands?

1071

1072

It might about the channels mapping. Please see for detail.

1073

1074

[[http:~~/~~/wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band>>url:http://wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band]]

1. Order Info

**Part Number: RS485-BL-XXX**

**XXX:**

* **EU433**: frequency bands EU433

1085

* **EU868**: frequency bands EU868

1086

* **KR920**: frequency bands KR920

1087

* **CN470**: frequency bands CN470

1088

* **AS923**: frequency bands AS923

1089

* **AU915**: frequency bands AU915

1090

* **US915**: frequency bands US915

1091

* **IN865**: frequency bands IN865

1092

* **RU864**: frequency bands RU864

1093

* **KZ865: **frequency bands KZ865

1. Packing Info

**Package Includes**:

1098

1099

* RS485-BL x 1

1100

* Stick Antenna for LoRa RF part x 1

1101

* Program cable x 1

1102

1103

**Dimension and weight**:

1104

1105

* Device Size: 13.5 x 7 x 3 cm

1106

* Device Weight: 105g

1107

* Package Size / pcs : 14.5 x 8 x 5 cm

1108

* Weight / pcs : 170g

1. Support

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1113

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to

1114

1115

[[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]

Wiki source code of RS485-LN – RS485 to LoRaWAN Converter

Applications

Navigation