Skip to Content
Version 54.2 by Xiaoling on 2023/04/26 08:53
Show last authors
1 [[image:image-20230131115217-1.png]]
2
3
4
5 **Table of Contents：**
6
7 {{toc/}}
8
9
10
11
12
13
14 = 1. Introduction =
15
16 == 1.1 What is LoRaWAN Pressure Sensor ==
17
18
19 (((
20 The Dragino PS-LB series sensors are (% style="color:blue" %)**LoRaWAN Pressure Sensor**(%%) for Internet of Things solution. PS-LB can measure Air, Water pressure and liquid level and upload the sensor data via wireless to LoRaWAN IoT server.
21 )))
22
23 (((
24 The PS-LB series sensors include (% style="color:blue" %)**Thread Installation Type**(%%) and (% style="color:blue" %)**Immersion Type**(%%), it supports different pressure range which can be used for different measurement requirement.
25 )))
26
27 (((
28 The LoRa wireless technology used in PS-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
29 )))
30
31 (((
32 PS-LB supports BLE configure and wireless OTA update which make user easy to use.
33 )))
34
35 (((
36 PS-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
37 )))
38
39 (((
40 Each PS-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
41 )))
42
43 [[image:1675071321348-194.png]]
44
45
46 == 1.2 ​Features ==
47
48
49 * LoRaWAN 1.0.3 Class A
50 * Ultra-low power consumption
51 * Measure air / gas or water pressure
52 * Different pressure range available
53 * Thread Installation Type or Immersion Type
54 * Monitor Battery Level
55 * Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
56 * Support Bluetooth v5.1 and LoRaWAN remote configure
57 * Support wireless OTA update firmware
58 * Uplink on periodically
59 * Downlink to change configure
60 * 8500mAh Battery for long term use
61 * Controllable 3.3v,5v and 12v output to power external sensor
62
63
64 == 1.3 Specification ==
65
66
67 (% style="color:#037691" %)**Micro Controller:**
68
69 * MCU: 48Mhz ARM
70 * Flash: 256KB
71 * RAM: 64KB
72
73 (% style="color:#037691" %)**Common DC Characteristics:**
74
75 * Supply Voltage: 2.5v ~~ 3.6v
76 * Operating Temperature: -40 ~~ 85°C
77
78 (% style="color:#037691" %)**LoRa Spec:**
79
80 * Frequency Range,  Band 1 (HF): 862 ~~ 1020 Mhz
81 * Max +22 dBm constant RF output vs.
82 * RX sensitivity: down to -139 dBm.
83 * Excellent blocking immunity
84
85 (% style="color:#037691" %)**Current Input Measuring :**
86
87 * Range: 0 ~~ 20mA
88 * Accuracy: 0.02mA
89 * Resolution: 0.001mA
90
91 (% style="color:#037691" %)**Voltage Input Measuring:**
92
93 * Range: 0 ~~ 30v
94 * Accuracy: 0.02v
95 * Resolution: 0.001v
96
97 (% style="color:#037691" %)**Battery:**
98
99 * Li/SOCI2 un-chargeable battery
100 * Capacity: 8500mAh
101 * Self-Discharge: <1% / Year @ 25°C
102 * Max continuously current: 130mA
103 * Max boost current: 2A, 1 second
104
105 (% style="color:#037691" %)**Power Consumption**
106
107 * Sleep Mode: 5uA @ 3.3v
108 * LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
109
110
111 == 1.4 Probe Types ==
112
113 === 1.4.1 Thread Installation Type ===
114
115
116 [[image:1675071448299-229.png]]
117
118 * Hersman Pressure Transmitter
119 * Measuring Range: -0.1 ~~ 0 ~~ 60MPa, see order info.
120 * Accuracy: 0.2% F.S
121 * Long-Term Stability: 0.2% F.S ±0.05%
122 * Overload 200% F.S
123 * Zero Temperature Drift: 0.03% FS/℃(≤100Kpa), 0.02%FS/℃(＞100Kpa)
124 * FS Temperature Drift: 0.003% FS/℃(≤100Kpa), 0.002%FS/℃(＞100Kpa)
125 * Storage temperature: -30℃~~80℃
126 * Operating temperature: -20℃~~60℃
127 * Connector Type: Various Types, see order info
128
129
130 === 1.4.2 Immersion Type ===
131
132
133 [[image:1675071521308-426.png]]
134
135 * Immersion Type, Probe IP Level: IP68
136 * Measuring Range: Measure range can be customized, up to 100m.
137 * Accuracy: 0.2% F.S
138 * Long-Term Stability: ±0.2% F.S / Year
139 * Storage temperature: -30℃~~80℃
140 * Operating temperature: 0℃~~50℃
141 * Material: 316 stainless steels
142
143
144 == 1.5 Probe Dimension ==
145
146
147
148 == 1.6 Application and Installation ==
149
150 === 1.6.1 Thread Installation Type ===
151
152
153 (% style="color:blue" %)**Application:**
154
155 * Hydraulic Pressure
156 * Petrochemical Industry
157 * Health and Medical
158 * Food & Beverage Processing
159 * Auto-controlling house
160 * Constant Pressure Water Supply
161 * Liquid Pressure measuring
162
163 Order the suitable thread size and install to measure the air / liquid pressure
164
165 [[image:1675071670469-145.png]]
166
167
168 === 1.6.2 Immersion Type ===
169
170
171 (% style="color:blue" %)**Application:**
172
173 Liquid & Water Pressure / Level detect.
174
175 [[image:1675071725288-579.png]]
176
177
178 The Immersion Type pressure sensor is shipped with the probe and device separately. When user got the device, below is the wiring to for connect the probe to the device.
179
180
181 [[image:1675071736646-450.png]]
182
183
184 [[image:1675071776102-240.png]]
185
186
187 == 1.7 Sleep mode and working mode ==
188
189
190 (% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
191
192 (% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
193
194
195 == 1.8 Button & LEDs ==
196
197
198 [[image:1675071855856-879.png]]
199
200
201 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
202 |=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)**Action**
203 |(% style="background-color:#f2f2f2; width:167px" %)Pressing ACT between 1s < time < 3s|(% style="background-color:#f2f2f2; width:117px" %)Send an uplink|(% style="background-color:#f2f2f2; width:225px" %)(((
204 If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.
205 Meanwhile, BLE module will be active and user can connect via BLE to configure device.
206 )))
207 |(% style="background-color:#f2f2f2; width:167px" %)Pressing ACT for more than 3s|(% style="background-color:#f2f2f2; width:117px" %)Active Device|(% style="background-color:#f2f2f2; width:225px" %)(((
208 (% style="background-color:#f2f2f2; color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
209 (% style="background-color:#f2f2f2; color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
210 Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
211 )))
212 |(% style="background-color:#f2f2f2; width:167px" %)Fast press ACT 5 times.|(% style="background-color:#f2f2f2; width:117px" %)Deactivate Device|(% style="background-color:#f2f2f2; width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means PS-LB-NA is in Deep Sleep Mode.
213
214
215 == 1.9 Pin Mapping ==
216
217
218 [[image:1675072568006-274.png]]
219
220
221 == 1.10 BLE connection ==
222
223
224 PS-LB support BLE remote configure.
225
226
227 BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
228
229 * Press button to send an uplink
230 * Press button to active device.
231 * Device Power on or reset.
232
233 If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
234
235
236 == 1.11 Mechanical ==
237
238
239 [[image:1675143884058-338.png]]
240
241
242 [[image:1675143899218-599.png]]
243
244
245 [[image:1675143909447-639.png]]
246
247
248 = 2. Configure PS-LB to connect to LoRaWAN network =
249
250 == 2.1 How it works ==
251
252
253 The PS-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and activate the PS-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
254
255
256 == 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
257
258
259 Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
260
261
262 [[image:1675144005218-297.png]]
263
264
265 The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
266
267
268 (% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from PS-LB.
269
270 Each PS-LB is shipped with a sticker with the default device EUI as below:
271
272 [[image:image-20230426085320-1.png]]
273
274
275 You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
276
277
278 (% style="color:blue" %)**Register the device**
279
280 [[image:1675144099263-405.png]]
281
282
283 (% style="color:blue" %)**Add APP EUI and DEV EUI**
284
285 [[image:1675144117571-832.png]]
286
287
288 (% style="color:blue" %)**Add APP EUI in the application**
289
290
291 [[image:1675144143021-195.png]]
292
293
294 (% style="color:blue" %)**Add APP KEY**
295
296 [[image:1675144157838-392.png]]
297
298 (% style="color:blue" %)**Step 2:**(%%) Activate on PS-LB
299
300
301 Press the button for 5 seconds to activate the PS-LB.
302
303 (% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
304
305 After join success, it will start to upload messages to TTN and you can see the messages in the panel.
306
307
308 == 2.3 ​Uplink Payload ==
309
310 === 2.3.1 Device Status, FPORT~=5 ===
311
312
313 Include device configure status. Once PS-LB Joined the network, it will uplink this message to the server.
314
315 Users can also use the downlink command(0x26 01) to ask PS-LB to resend this uplink.
316
317
318 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
319 |(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**
320 |(% style="background-color:#f2f2f2; width:103px" %)**Size (bytes)**|(% style="background-color:#f2f2f2; width:72px" %)**1**|(% style="background-color:#f2f2f2" %)**2**|(% style="background-color:#f2f2f2; width:91px" %)**1**|(% style="background-color:#f2f2f2; width:86px" %)**1**|(% style="background-color:#f2f2f2; width:44px" %)**2**
321 |(% style="background-color:#f2f2f2; width:103px" %)**Value**|(% style="background-color:#f2f2f2; width:72px" %)Sensor Model|(% style="background-color:#f2f2f2" %)Firmware Version|(% style="background-color:#f2f2f2; width:91px" %)Frequency Band|(% style="background-color:#f2f2f2; width:86px" %)Sub-band|(% style="background-color:#f2f2f2; width:44px" %)BAT
322
323 Example parse in TTNv3
324
325 [[image:1675144504430-490.png]]
326
327
328 (% style="color:#037691" %)**Sensor Model**(%%): For PS-LB, this value is 0x16
329
330 (% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
331
332 (% style="color:#037691" %)**Frequency Band**:
333
334 *0x01: EU868
335
336 *0x02: US915
337
338 *0x03: IN865
339
340 *0x04: AU915
341
342 *0x05: KZ865
343
344 *0x06: RU864
345
346 *0x07: AS923
347
348 *0x08: AS923-1
349
350 *0x09: AS923-2
351
352 *0x0a: AS923-3
353
354 *0x0b: CN470
355
356 *0x0c: EU433
357
358 *0x0d: KR920
359
360 *0x0e: MA869
361
362
363 (% style="color:#037691" %)**Sub-Band**:
364
365 AU915 and US915:value 0x00 ~~ 0x08
366
367 CN470: value 0x0B ~~ 0x0C
368
369 Other Bands: Always 0x00
370
371
372 (% style="color:#037691" %)**Battery Info**:
373
374 Check the battery voltage.
375
376 Ex1: 0x0B45 = 2885mV
377
378 Ex2: 0x0B49 = 2889mV
379
380
381 === 2.3.2 Sensor value, FPORT~=2 ===
382
383
384 Uplink payload includes in total 9 bytes.
385
386
387 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
388 |(% style="background-color:#d9e2f3; width:97px" %)(((
389 **Size(bytes)**
390 )))|(% style="background-color:#d9e2f3; width:48px" %)**2**|(% style="background-color:#d9e2f3; width:71px" %)**2**|(% style="background-color:#d9e2f3; width:98px" %)**2**|(% style="background-color:#d9e2f3; width:73px" %)**2**|(% style="background-color:#d9e2f3; width:122px" %)**1**
391 |(% style="width:97px" %)**Value**|(% style="width:48px" %)[[BAT>>||anchor="H2.3.3BatteryInfo"]]|(% style="width:71px" %)[[Probe Model>>||anchor="H2.3.4ProbeModel"]]|(% style="width:98px" %)[[0 ~~~~ 20mA value>>||anchor="H2.3.507E20mAvalue28IDC_IN29"]]|(% style="width:73px" %)[[0 ~~~~ 30v value>>||anchor="H2.3.607E30Vvalue28pinVDC_IN29"]]|(% style="width:122px" %)[[IN1 &IN2 Interrupt  flag>>||anchor="H2.3.7IN126IN226INTpin"]]
392
393 [[image:1675144608950-310.png]]
394
395
396 === 2.3.3 Battery Info ===
397
398
399 Check the battery voltage for PS-LB.
400
401 Ex1: 0x0B45 = 2885mV
402
403 Ex2: 0x0B49 = 2889mV
404
405
406 === 2.3.4 Probe Model ===
407
408
409 PS-LB has different kind of probe, 4~~20mA represent the full scale of the measuring range. So a 12mA output means different meaning for different probe. 
410
411
412 **For example.**
413
414 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
415 |(% style="background-color:#d9e2f3; color:#0070c0" %)**Part Number**|(% style="background-color:#d9e2f3; color:#0070c0" %)**Probe Used**|(% style="background-color:#d9e2f3; color:#0070c0" %)**4~~20mA scale**|(% style="background-color:#d9e2f3; color:#0070c0" %)**Example: 12mA meaning**
416 |(% style="background-color:#f2f2f2" %)PS-LB-I3|(% style="background-color:#f2f2f2" %)immersion type with 3 meters cable|(% style="background-color:#f2f2f2" %)0~~3 meters|(% style="background-color:#f2f2f2" %)1.5 meters pure water
417 |(% style="background-color:#f2f2f2" %)PS-LB-I5|(% style="background-color:#f2f2f2" %)immersion type with 5 meters cable|(% style="background-color:#f2f2f2" %)0~~5 meters|(% style="background-color:#f2f2f2" %)2.5 meters pure water
418 |(% style="background-color:#f2f2f2" %)PS-LB-T20-B|(% style="background-color:#f2f2f2" %)T20 threaded probe|(% style="background-color:#f2f2f2" %)0~~1MPa|(% style="background-color:#f2f2f2" %)0.5MPa air / gas or water pressure
419
420 The probe model field provides the convenient for server to identical how it should parse the 4~~20mA sensor value and get the correct value.
421
422
423 === 2.3.5 0~~20mA value (IDC_IN) ===
424
425
426 The output value from **Pressure Probe**, use together with Probe Model to get the pressure value or water level.
427
428 (% style="color:#037691" %)**Example**:
429
430 27AE(H) = 10158 (D)/1000 = 10.158mA.
431
432
433 Instead of pressure probe, User can also connect a general 4~~20mA in this port to support different types of 4~~20mA sensors. below is the connection example:
434
435 [[image:image-20230225154759-1.png||height="408" width="741"]]
436
437
438 === 2.3.6 0~~30V value ( pin VDC_IN) ===
439
440
441 Measure the voltage value. The range is 0 to 30V.
442
443 (% style="color:#037691" %)**Example**:
444
445 138E(H) = 5006(D)/1000= 5.006V
446
447
448 === 2.3.7 IN1&IN2&INT pin ===
449
450
451 IN1 and IN2 are used as digital input pins.
452
453 (% style="color:#037691" %)**Example**:
454
455 09 (H): (0x09&0x08)>>3=1    IN1 pin is high level.
456
457 09 (H): (0x09&0x04)>>2=0    IN2 pin is low level.
458
459
460 This data field shows if this packet is generated by (% style="color:blue" %)**Interrupt Pin** (%%)or not. [[Click here>>||anchor="H3.3.2SetInterruptMode"]] for the hardware and software set up. Note: The Internet Pin is a separate pin in the screw terminal.
461
462 (% style="color:#037691" %)**Example:**
463
464 09 (H): (0x09&0x02)>>1=1    The level of the interrupt pin.
465
466 09 (H): 0x09&0x01=1              0x00: Normal uplink packet.
467
468 0x01: Interrupt Uplink Packet.
469
470
471 === (% id="cke_bm_109176S" style="display:none" %) (%%)2.3.8 Sensor value, FPORT~=7 ===
472
473
474 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:508.222px" %)
475 |(% style="background-color:#d9e2f3; width:94px" %)(((
476 **Size(bytes)**
477 )))|(% style="background-color:#d9e2f3; width:43px" %)2|(% style="background-color:#d9e2f3; width:367px" %)n
478 |(% style="width:94px" %)**Value**|(% style="width:43px" %)[[BAT>>||anchor="H2.3.3BatteryInfo"]]|(% style="width:367px" %)(((
479 Voltage value, each 2 bytes is a set of voltage values.
480 )))
481
482 [[image:image-20230220171300-1.png||height="207" width="863"]]
483
484 Multiple sets of data collected are displayed in this form：
485
486 [voltage value1], [voltage value2], [voltage value3],…[voltage value n/2]
487
488
489 === 2.3.9 ​Decode payload in The Things Network ===
490
491
492 While using TTN network, you can add the payload format to decode the payload.
493
494
495 [[image:1675144839454-913.png]]
496
497
498 PS-LB TTN Payload Decoder: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]
499
500
501 == 2.4 Uplink Interval ==
502
503
504 The PS-LB by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H4.1ChangeUplinkInterval>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H4.1ChangeUplinkInterval||style="background-color: rgb(255, 255, 255);"]]
505
506
507 == 2.5 Show Data in DataCake IoT Server ==
508
509
510 [[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
511
512
513 (% style="color:blue" %)**Step 1: **(%%)Be sure that your device is programmed and properly connected to the network at this time.
514
515 (% style="color:blue" %)**Step 2:**(%%) To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
516
517
518 [[image:1675144951092-237.png]]
519
520
521 [[image:1675144960452-126.png]]
522
523
524 (% style="color:blue" %)**Step 3:**(%%) Create an account or log in Datacake.
525
526 (% style="color:blue" %)**Step 4:** (%%)Create PS-LB product.
527
528 [[image:1675145004465-869.png]]
529
530
531 [[image:1675145018212-853.png]]
532
533
534
535
536 [[image:1675145029119-717.png]]
537
538
539 (% style="color:blue" %)**Step 5: **(%%)add payload decode
540
541 [[image:1675145051360-659.png]]
542
543
544 [[image:1675145060812-420.png]]
545
546
547 After added, the sensor data arrive TTN, it will also arrive and show in Datacake.
548
549
550 [[image:1675145081239-376.png]]
551
552
553 == 2.6 Frequency Plans ==
554
555
556 The PS-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
557
558 [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
559
560
561 == 2.7 ​Firmware Change Log ==
562
563
564 **Firmware download link:**
565
566 [[https:~~/~~/www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0>>url:https://www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0]]
567
568
569 = 3. Configure PS-LB =
570
571 == 3.1 Configure Methods ==
572
573
574 PS-LB-NA supports below configure method:
575
576 * AT Command via Bluetooth Connection (**Recommand Way**): [[BLE Configure Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
577 * AT Command via UART Connection : See [[FAQ>>||anchor="H6.FAQ"]].
578 * LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>url:http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
579
580
581 == 3.2 General Commands ==
582
583
584 These commands are to configure:
585
586 * General system settings like: uplink interval.
587 * LoRaWAN protocol & radio related command.
588
589 They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
590
591 [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
592
593
594 == 3.3 Commands special design for PS-LB ==
595
596
597 These commands only valid for PS-LB, as below:
598
599
600 === 3.3.1 Set Transmit Interval Time ===
601
602
603 Feature: Change LoRaWAN End Node Transmit Interval.
604
605 (% style="color:blue" %)**AT Command: AT+TDC**
606
607 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
608 |=(% style="width: 160px; background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 160px; background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 190px;background-color:#D9E2F3;color:#0070C0" %)**Response**
609 |(% style="background-color:#f2f2f2; width:157px" %)AT+TDC=?|(% style="background-color:#f2f2f2; width:166px" %)Show current transmit Interval|(% style="background-color:#f2f2f2" %)(((
610 30000
611 OK
612 the interval is 30000ms = 30s
613 )))
614 |(% style="background-color:#f2f2f2; width:157px" %)AT+TDC=60000|(% style="background-color:#f2f2f2; width:166px" %)Set Transmit Interval|(% style="background-color:#f2f2f2" %)(((
615 OK
616 Set transmit interval to 60000ms = 60 seconds
617 )))
618
619 (% style="color:blue" %)**Downlink Command: 0x01**
620
621 Format: Command Code (0x01) followed by 3 bytes time value.
622
623 If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
624
625 * Example 1: Downlink Payload: 0100001E  ~/~/  Set Transmit Interval (TDC) = 30 seconds
626 * Example 2: Downlink Payload: 0100003C  ~/~/  Set Transmit Interval (TDC) = 60 seconds
627
628
629 === 3.3.2 Set Interrupt Mode ===
630
631
632 Feature, Set Interrupt mode for GPIO_EXIT.
633
634 (% style="color:blue" %)**AT Command: AT+INTMOD**
635
636 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
637 |=(% style="width: 154px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3;color:#0070C0" %)**Response**
638 |(% style="background-color:#f2f2f2; width:154px" %)AT+INTMOD=?|(% style="background-color:#f2f2f2; width:196px" %)Show current interrupt mode|(% style="background-color:#f2f2f2; width:157px" %)(((
639 0
640 OK
641 the mode is 0 =Disable Interrupt
642 )))
643 |(% style="background-color:#f2f2f2; width:154px" %)AT+INTMOD=2|(% style="background-color:#f2f2f2; width:196px" %)(((
644 Set Transmit Interval
645 0. (Disable Interrupt),
646 ~1. (Trigger by rising and falling edge)
647 2. (Trigger by falling edge)
648 3. (Trigger by rising edge)
649 )))|(% style="background-color:#f2f2f2; width:157px" %)OK
650
651 (% style="color:blue" %)**Downlink Command: 0x06**
652
653 Format: Command Code (0x06) followed by 3 bytes.
654
655 This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
656
657 * Example 1: Downlink Payload: 06000000  ~/~/  Turn off interrupt mode
658 * Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
659
660
661 === 3.3.3 Set the output time ===
662
663
664 Feature, Control the output 3V3 , 5V or 12V.
665
666 (% style="color:blue" %)**AT Command: AT+3V3T**
667
668 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:474px" %)
669 |=(% style="width: 154px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 201px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 116px;background-color:#D9E2F3;color:#0070C0" %)**Response**
670 |(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=?|(% style="background-color:#f2f2f2; width:201px" %)Show 3V3 open time.|(% style="background-color:#f2f2f2; width:116px" %)(((
671 0
672 OK
673 )))
674 |(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=0|(% style="background-color:#f2f2f2; width:201px" %)Normally open 3V3 power supply.|(% style="background-color:#f2f2f2; width:116px" %)(((
675 OK
676 default setting
677 )))
678 |(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=1000|(% style="background-color:#f2f2f2; width:201px" %)Close after a delay of 1000 milliseconds.|(% style="background-color:#f2f2f2; width:116px" %)(((
679 OK
680 )))
681 |(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=65535|(% style="background-color:#f2f2f2; width:201px" %)Normally closed 3V3 power supply.|(% style="background-color:#f2f2f2; width:116px" %)(((
682 OK
683 )))
684
685 (% style="color:blue" %)**AT Command: AT+5VT**
686
687 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:470px" %)
688 |=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 114px;background-color:#D9E2F3;color:#0070C0" %)**Response**
689 |(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=?|(% style="background-color:#f2f2f2; width:196px" %)Show 5V open time.|(% style="background-color:#f2f2f2; width:114px" %)(((
690 0
691 OK
692 )))
693 |(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=0|(% style="background-color:#f2f2f2; width:196px" %)Normally closed 5V power supply.|(% style="background-color:#f2f2f2; width:114px" %)(((
694 OK
695 default setting
696 )))
697 |(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=1000|(% style="background-color:#f2f2f2; width:196px" %)Close after a delay of 1000 milliseconds.|(% style="background-color:#f2f2f2; width:114px" %)(((
698 OK
699 )))
700 |(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=65535|(% style="background-color:#f2f2f2; width:196px" %)Normally open 5V power supply.|(% style="background-color:#f2f2f2; width:114px" %)(((
701 OK
702 )))
703
704 (% style="color:blue" %)**AT Command: AT+12VT**
705
706 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:443px" %)
707 |=(% style="width: 156px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 199px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 83px;background-color:#D9E2F3;color:#0070C0" %)**Response**
708 |(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=?|(% style="background-color:#f2f2f2; width:199px" %)Show 12V open time.|(% style="background-color:#f2f2f2; width:83px" %)(((
709 0
710 OK
711 )))
712 |(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=0|(% style="background-color:#f2f2f2; width:199px" %)Normally closed 12V power supply.|(% style="background-color:#f2f2f2; width:83px" %)OK
713 |(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=500|(% style="background-color:#f2f2f2; width:199px" %)Close after a delay of 500 milliseconds.|(% style="background-color:#f2f2f2; width:83px" %)(((
714 OK
715 )))
716
717 (% style="color:blue" %)**Downlink Command: 0x07**
718
719 Format: Command Code (0x07) followed by 3 bytes.
720
721 The first byte is which power, the second and third bytes are the time to turn on.
722
723 * Example 1: Downlink Payload: 070101F4  **~-~-->**  AT+3V3T=500
724 * Example 2: Downlink Payload: 0701FFFF   **~-~-->**  AT+3V3T=65535
725 * Example 3: Downlink Payload: 070203E8  **~-~-->**  AT+5VT=1000
726 * Example 4: Downlink Payload: 07020000  **~-~-->**  AT+5VT=0
727 * Example 5: Downlink Payload: 070301F4  **~-~-->**  AT+12VT=500
728 * Example 6: Downlink Payload: 07030000  **~-~-->**  AT+12VT=0
729
730
731 === 3.3.4 Set the Probe Model ===
732
733
734 Users need to configure this parameter according to the type of external probe. In this way, the server can decode according to this value, and convert the current value output by the sensor into water depth or pressure value.
735
736 (% style="color:blue" %)**AT Command: AT** **+PROBE**
737
738 AT+PROBE=aabb
739
740 When aa=00, it is the water depth mode, and the current is converted into the water depth value; bb is the probe at a depth of several meters.
741
742 When aa=01, it is the pressure mode, which converts the current into a pressure value;
743
744 bb represents which type of pressure sensor it is.
745
746 (A->01,B->02,C->03,D->04,E->05,F->06,G->07,H->08,I->09,J->0A,K->0B,L->0C)
747
748 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
749 |(% style="background-color:#d9e2f3; color:#0070c0; width:154px" %)**Command Example**|(% style="background-color:#d9e2f3; color:#0070c0; width:269px" %)**Function**|(% style="background-color:#d9e2f3; color:#0070c0" %)**Response**
750 |(% style="background-color:#f2f2f2; width:154px" %)AT +PROBE =?|(% style="background-color:#f2f2f2; width:269px" %)Get or Set the probe model.|(% style="background-color:#f2f2f2" %)0
751 OK
752 |(% style="background-color:#f2f2f2; width:154px" %)AT +PROBE =0003|(% style="background-color:#f2f2f2; width:269px" %)Set water depth sensor mode, 3m type.|(% style="background-color:#f2f2f2" %)OK
753 |(% style="background-color:#f2f2f2; width:154px" %)(((
754 AT +PROBE =000A
755
756
757 )))|(% style="background-color:#f2f2f2; width:269px" %)Set water depth sensor mode, 10m type.|(% style="background-color:#f2f2f2" %)OK
758 |(% style="background-color:#f2f2f2; width:154px" %)AT +PROBE =0101|(% style="background-color:#f2f2f2; width:269px" %)Set pressure transmitters mode, first type(A).|(% style="background-color:#f2f2f2" %)OK
759 |(% style="background-color:#f2f2f2; width:154px" %)AT +PROBE =0000|(% style="background-color:#f2f2f2; width:269px" %)Initial state, no settings.|(% style="background-color:#f2f2f2" %)OK
760
761 (% style="color:blue" %)**Downlink Command: 0x08**
762
763 Format: Command Code (0x08) followed by 2 bytes.
764
765 * Example 1: Downlink Payload: 080003  **~-~-->**  AT+PROBE=0003
766 * Example 2: Downlink Payload: 080101  **~-~-->**  AT+PROBE=0101
767
768
769 === 3.3.5 Multiple collections are one uplink（Since firmware V1.1） ===
770
771
772 Added AT+STDC command to collect the voltage of VDC_INPUT multiple times and upload it at one time.
773
774 (% style="color:blue" %)**AT Command: AT** **+STDC**
775
776 AT+STDC=aa,bb,bb
777
778 (% style="color:#037691" %)**aa:**(%%)
779 **0:** means disable this function and use TDC to send packets.
780 **1:** means enable this function, use the method of multiple acquisitions to send packets.
781 (% style="color:#037691" %)**bb:**(%%) Each collection interval (s), the value is 1~~65535
782 (% style="color:#037691" %)**cc:**(%%)** **the number of collection times, the value is 1~~120
783
784 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
785 |(% style="background-color:#d9e2f3; color:#0070c0; width:160px" %)**Command Example**|(% style="background-color:#d9e2f3; color:#0070c0; width:215px" %)**Function**|(% style="background-color:#d9e2f3; color:#0070c0" %)**Response**
786 |(% style="background-color:#f2f2f2; width:160px" %)AT+STDC=?|(% style="background-color:#f2f2f2; width:215px" %)Get the mode of multiple acquisitions and one uplink.|(% style="background-color:#f2f2f2" %)1,10,18
787 OK
788 |(% style="background-color:#f2f2f2; width:160px" %)AT+STDC=1,10,18|(% style="background-color:#f2f2f2; width:215px" %)Set the mode of multiple acquisitions and one uplink, collect once every 10 seconds, and report after 18 times.|(% style="background-color:#f2f2f2" %)(((
789 Attention:Take effect after ATZ
790
791 OK
792 )))
793 |(% style="background-color:#f2f2f2; width:160px" %)AT+STDC=0, 0,0|(% style="background-color:#f2f2f2; width:215px" %)(((
794 Use the TDC interval to send packets.(default)
795
796
797 )))|(% style="background-color:#f2f2f2" %)(((
798 Attention:Take effect after ATZ
799
800 OK
801 )))
802
803 (% style="color:blue" %)**Downlink Command: 0xAE**
804
805 Format: Command Code (0x08) followed by 5 bytes.
806
807 * Example 1: Downlink Payload: AE 01 02 58 12** ~-~-->**  AT+STDC=1,600,18
808
809
810 = 4. Battery & Power Consumption =
811
812
813 PS-LB-NA uses ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
814
815 [[**Battery Info & Power Consumption Analyze**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
816
817
818 = 5. OTA firmware update =
819
820
821 Please see this link for how to do OTA firmware update: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
822
823
824 = 6. FAQ =
825
826 == 6.1 How to use AT Command via UART to access device? ==
827
828
829 See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
830
831
832 == 6.2 How to update firmware via UART port? ==
833
834
835 See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
836
837
838 == 6.3 How to change the LoRa Frequency Bands/Region? ==
839
840
841 You can follow the instructions for [[how to upgrade image>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]].
842 When downloading the images, choose the required image file for download. ​
843
844
845 = 7. Order Info =
846
847
848 [[image:image-20230131153105-4.png]]
849
850
851 = 8. ​Packing Info =
852
853
854 (% style="color:#037691" %)**Package Includes**:
855
856 * PS-LB LoRaWAN Pressure Sensor
857
858 (% style="color:#037691" %)**Dimension and weight**:
859
860 * Device Size: cm
861 * Device Weight: g
862 * Package Size / pcs : cm
863 * Weight / pcs : g
864
865
866 = 9. Support =
867
868
869 * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
870
871 * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
872
873