Wiki source code of PS-LB -- LoRaWAN Air Water Pressure Sensor User Manual

Version 52.2 by Xiaoling on 2023/03/24 13:55

version	line-number	content
16.2	1	[[image:image-20230131115217-1.png]]
6.2	2
	3
	4
	5	Table of Contents：
	6
42.4	7	{{toc/}}
6.2	8
	9
	10
42.5	11
	12
	13
16.2	14	= 1. Introduction =
6.2	15
9.2	16	== 1.1 What is LoRaWAN Pressure Sensor ==
	17
	18
42.31	19	(((
42.17	20	The Dragino PS-LB series sensors are (% style="color:blue" %)LoRaWAN Pressure Sensor(%%) for Internet of Things solution. PS-LB can measure Air, Water pressure and liquid level and upload the sensor data via wireless to LoRaWAN IoT server.
42.31	21	)))
6.2	22
42.31	23	(((
42.17	24	The PS-LB series sensors include (% style="color:blue" %)Thread Installation Type(%%) and (% style="color:blue" %)Immersion Type(%%), it supports different pressure range which can be used for different measurement requirement.
42.31	25	)))
6.2	26
42.31	27	(((
6.2	28	The LoRa wireless technology used in PS-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
42.31	29	)))
6.2	30
42.31	31	(((
6.2	32	PS-LB supports BLE configure and wireless OTA update which make user easy to use.
42.31	33	)))
6.2	34
42.31	35	(((
42.17	36	PS-LB is powered by (% style="color:blue" %)8500mAh Li-SOCI2 battery(%%), it is designed for long term use up to 5 years.
42.31	37	)))
6.2	38
42.31	39	(((
6.2	40	Each PS-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
42.31	41	)))
6.2	42
9.2	43	[[image:1675071321348-194.png]]
6.2	44
	45
9.2	46	== 1.2 Features ==
6.2	47
	48
	49	* LoRaWAN 1.0.3 Class A
	50	* Ultra-low power consumption
	51	* Measure air / gas or water pressure
	52	* Different pressure range available
	53	* Thread Installation Type or Immersion Type
	54	* Monitor Battery Level
	55	* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
	56	* Support Bluetooth v5.1 and LoRaWAN remote configure
	57	* Support wireless OTA update firmware
	58	* Uplink on periodically
	59	* Downlink to change configure
	60	* 8500mAh Battery for long term use
47.1	61	* Controllable 3.3v,5v and 12v output to power external sensor
6.2	62
50.2	63
52.2	64
9.2	65	== 1.3 Specification ==
	66
	67
42.17	68	(% style="color:#037691" %)Micro Controller:
6.2	69
	70	* MCU: 48Mhz ARM
	71	* Flash: 256KB
	72	* RAM: 64KB
	73
42.17	74	(% style="color:#037691" %)Common DC Characteristics:
6.2	75
	76	* Supply Voltage: 2.5v ~~ 3.6v
	77	* Operating Temperature: -40 ~~ 85°C
	78
42.17	79	(% style="color:#037691" %)LoRa Spec:
6.2	80
	81	* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz
	82	* Max +22 dBm constant RF output vs.
	83	* RX sensitivity: down to -139 dBm.
	84	* Excellent blocking immunity
	85
42.17	86	(% style="color:#037691" %)Current Input Measuring :
6.2	87
	88	* Range: 0 ~~ 20mA
	89	* Accuracy: 0.02mA
	90	* Resolution: 0.001mA
	91
42.17	92	(% style="color:#037691" %)Voltage Input Measuring:
6.2	93
	94	* Range: 0 ~~ 30v
	95	* Accuracy: 0.02v
	96	* Resolution: 0.001v
	97
42.17	98	(% style="color:#037691" %)Battery:
6.2	99
	100	* Li/SOCI2 un-chargeable battery
	101	* Capacity: 8500mAh
	102	* Self-Discharge: <1% / Year @ 25°C
	103	* Max continuously current: 130mA
	104	* Max boost current: 2A, 1 second
	105
42.17	106	(% style="color:#037691" %)Power Consumption
6.2	107
	108	* Sleep Mode: 5uA @ 3.3v
	109	* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
	110
50.2	111
52.2	112
9.2	113	== 1.4 Probe Types ==
6.2	114
9.2	115	=== 1.4.1 Thread Installation Type ===
6.2	116
	117
9.2	118	[[image:1675071448299-229.png]]
6.2	119
9.2	120	* Hersman Pressure Transmitter
	121	* Measuring Range: -0.1 ~~ 0 ~~ 60MPa, see order info.
	122	* Accuracy: 0.2% F.S
	123	* Long-Term Stability: 0.2% F.S ±0.05%
	124	* Overload 200% F.S
	125	* Zero Temperature Drift: 0.03% FS/℃(≤100Kpa), 0.02%FS/℃(＞100Kpa)
	126	* FS Temperature Drift: 0.003% FS/℃(≤100Kpa), 0.002%FS/℃(＞100Kpa)
	127	* Storage temperature: -30℃~~80℃
	128	* Operating temperature: -20℃~~60℃
	129	* Connector Type: Various Types, see order info
6.2	130
50.2	131
52.2	132
9.2	133	=== 1.4.2 Immersion Type ===
6.2	134
	135
9.2	136	[[image:1675071521308-426.png]]
	137
	138	* Immersion Type, Probe IP Level: IP68
	139	* Measuring Range: Measure range can be customized, up to 100m.
	140	* Accuracy: 0.2% F.S
	141	* Long-Term Stability: ±0.2% F.S / Year
	142	* Storage temperature: -30℃~~80℃
51.1	143	* Operating temperature: 0℃~~50℃
9.2	144	* Material: 316 stainless steels
	145
50.2	146
52.2	147
13.2	148	== 1.5 Probe Dimension ==
6.2	149
	150
13.2	151
	152	== 1.6 Application and Installation ==
	153
	154	=== 1.6.1 Thread Installation Type ===
	155
	156
42.17	157	(% style="color:blue" %)Application:
6.2	158
	159	* Hydraulic Pressure
	160	* Petrochemical Industry
	161	* Health and Medical
	162	* Food & Beverage Processing
	163	* Auto-controlling house
	164	* Constant Pressure Water Supply
	165	* Liquid Pressure measuring
	166
	167	Order the suitable thread size and install to measure the air / liquid pressure
	168
13.2	169	[[image:1675071670469-145.png]]
6.2	170
	171
13.2	172	=== 1.6.2 Immersion Type ===
6.2	173
	174
42.17	175	(% style="color:blue" %)Application:
6.2	176
	177	Liquid & Water Pressure / Level detect.
	178
13.2	179	[[image:1675071725288-579.png]]
6.2	180
	181
	182	The Immersion Type pressure sensor is shipped with the probe and device separately. When user got the device, below is the wiring to for connect the probe to the device.
	183
	184
13.2	185	[[image:1675071736646-450.png]]
6.2	186
	187
13.2	188	[[image:1675071776102-240.png]]
6.2	189
	190
14.2	191	== 1.7 Sleep mode and working mode ==
6.2	192
	193
42.17	194	(% style="color:blue" %)Deep Sleep Mode: (%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
6.2	195
42.17	196	(% style="color:blue" %)Working Mode: (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
6.2	197
	198
14.2	199	== 1.8 Button & LEDs ==
6.2	200
	201
14.2	202	[[image:1675071855856-879.png]]
6.2	203
	204
27.2	205	(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
42.32	206	\|=(% style="width: 167px;" %)Behavior on ACT\|=(% style="width: 117px;" %)Function\|=(% style="width: 225px;" %)Action
	207	\|(% style="width:167px" %)Pressing ACT between 1s < time < 3s\|(% style="width:117px" %)Send an uplink\|(% style="width:225px" %)(((
42.17	208	If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)blue led (%%)will blink once.
6.2	209	Meanwhile, BLE module will be active and user can connect via BLE to configure device.
	210	)))
42.32	211	\|(% style="width:167px" %)Pressing ACT for more than 3s\|(% style="width:117px" %)Active Device\|(% style="width:225px" %)(((
42.17	212	(% style="color:green" %)Green led(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)OTA mode(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
	213	(% style="color:green" %)Green led(%%) will solidly turn on for 5 seconds after joined in network.
6.2	214	Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
	215	)))
42.32	216	\|(% style="width:167px" %)Fast press ACT 5 times.\|(% style="width:117px" %)Deactivate Device\|(% style="width:225px" %)(% style="color:red" %)Red led(%%) will solid on for 5 seconds. Means PS-LB is in Deep Sleep Mode.
6.2	217
50.2	218
52.2	219
15.2	220	== 1.9 Pin Mapping ==
6.2	221
	222
15.2	223	[[image:1675072568006-274.png]]
6.2	224
	225
16.3	226	== 1.10 BLE connection ==
6.2	227
	228
	229	PS-LB support BLE remote configure.
	230
	231
	232	BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
	233
	234	* Press button to send an uplink
	235	* Press button to active device.
	236	* Device Power on or reset.
	237
	238	If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
	239
	240
17.2	241	== 1.11 Mechanical ==
6.2	242
	243
17.2	244	[[image:1675143884058-338.png]]
6.2	245
	246
26.2	247	[[image:1675143899218-599.png]]
6.2	248
	249
26.2	250	[[image:1675143909447-639.png]]
6.2	251
26.2	252
	253	= 2. Configure PS-LB to connect to LoRaWAN network =
	254
	255	== 2.1 How it works ==
	256
	257
42.17	258	The PS-LB is configured as (% style="color:#037691" %)LoRaWAN OTAA Class A(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and activate the PS-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
6.2	259
	260
26.2	261	== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==
	262
	263
6.2	264	Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
	265
	266
26.2	267	[[image:1675144005218-297.png]]
6.2	268
	269
	270	The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
	271
	272
42.17	273	(% style="color:blue" %)Step 1:(%%) Create a device in TTN with the OTAA keys from PS-LB.
6.2	274
	275	Each PS-LB is shipped with a sticker with the default device EUI as below:
	276
26.2	277	[[image:image-20230131134744-2.jpeg]]
6.2	278
	279
	280
	281	You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
	282
	283
42.17	284	(% style="color:blue" %)Register the device
6.2	285
26.2	286	[[image:1675144099263-405.png]]
6.2	287
	288
42.17	289	(% style="color:blue" %)Add APP EUI and DEV EUI
6.2	290
26.2	291	[[image:1675144117571-832.png]]
6.2	292
	293
42.17	294	(% style="color:blue" %)Add APP EUI in the application
6.2	295
	296
26.2	297	[[image:1675144143021-195.png]]
6.2	298
	299
42.17	300	(% style="color:blue" %)Add APP KEY
6.2	301
26.2	302	[[image:1675144157838-392.png]]
6.2	303
42.17	304	(% style="color:blue" %)Step 2:(%%) Activate on PS-LB
6.2	305
	306
	307	Press the button for 5 seconds to activate the PS-LB.
	308
42.17	309	(% style="color:green" %)Green led(%%) will fast blink 5 times, device will enter (% style="color:blue" %)OTA mode(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)Green led(%%) will solidly turn on for 5 seconds after joined in network.
6.2	310
	311	After join success, it will start to upload messages to TTN and you can see the messages in the panel.
	312
	313
27.2	314	== 2.3 Uplink Payload ==
6.2	315
27.2	316	=== 2.3.1 Device Status, FPORT~=5 ===
6.2	317
	318
	319	Include device configure status. Once PS-LB Joined the network, it will uplink this message to the server.
	320
	321	Users can also use the downlink command(0x26 01) to ask PS-LB to resend this uplink.
	322
	323
27.2	324	(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
6.2	325	\|(% colspan="6" %)Device Status (FPORT=5)
42.32	326	\|(% style="width:103px" %)Size (bytes)\|(% style="width:72px" %)1\|2\|(% style="width:91px" %)1\|(% style="width:86px" %)1\|(% style="width:44px" %)2
	327	\|(% style="width:103px" %)Value\|(% style="width:72px" %)Sensor Model\|Firmware Version\|(% style="width:91px" %)Frequency Band\|(% style="width:86px" %)Sub-band\|(% style="width:44px" %)BAT
6.2	328
	329	Example parse in TTNv3
	330
27.2	331	[[image:1675144504430-490.png]]
6.2	332
	333
42.17	334	(% style="color:#037691" %)Sensor Model(%%): For PS-LB, this value is 0x16
6.2	335
42.17	336	(% style="color:#037691" %)Firmware Version(%%): 0x0100, Means: v1.0.0 version
6.2	337
42.17	338	(% style="color:#037691" %)Frequency Band:
6.2	339
	340	*0x01: EU868
	341
	342	*0x02: US915
	343
	344	*0x03: IN865
	345
	346	*0x04: AU915
	347
	348	*0x05: KZ865
	349
	350	*0x06: RU864
	351
	352	*0x07: AS923
	353
	354	*0x08: AS923-1
	355
	356	*0x09: AS923-2
	357
	358	*0x0a: AS923-3
	359
	360	*0x0b: CN470
	361
	362	*0x0c: EU433
	363
	364	*0x0d: KR920
	365
	366	*0x0e: MA869
	367
	368
42.17	369	(% style="color:#037691" %)Sub-Band:
6.2	370
	371	AU915 and US915:value 0x00 ~~ 0x08
	372
	373	CN470: value 0x0B ~~ 0x0C
	374
	375	Other Bands: Always 0x00
	376
	377
42.17	378	(% style="color:#037691" %)Battery Info:
6.2	379
	380	Check the battery voltage.
	381
	382	Ex1: 0x0B45 = 2885mV
	383
	384	Ex2: 0x0B49 = 2889mV
	385
	386
42.11	387	=== 2.3.2 Sensor value, FPORT~=2 ===
6.2	388
	389
	390	Uplink payload includes in total 9 bytes.
	391
	392
27.2	393	(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
37.2	394	\|(% style="width:97px" %)(((
	395	Size(bytes)
42.24	396	)))\|(% style="width:48px" %)2\|(% style="width:71px" %)2\|(% style="width:98px" %)2\|(% style="width:73px" %)2\|(% style="width:122px" %)1
45.5	397	\|(% style="width:97px" %)Value\|(% style="width:48px" %)[[BAT>>\|\|anchor="H2.3.4BatteryInfo"]]\|(% style="width:71px" %)[[Probe Model>>\|\|anchor="H2.3.5ProbeModel"]]\|(% style="width:98px" %)[[0 ~~~~ 20mA value>>\|\|anchor="H2.3.607E20mAvalue28IDC_IN29"]]\|(% style="width:73px" %)[[0 ~~~~ 30v value>>\|\|anchor="H2.3.707E30Vvalue28pinVDC_IN29"]]\|(% style="width:122px" %)[[IN1 &IN2 Interrupt flag>>\|\|anchor="H2.3.8IN126IN226INTpin"]]
6.2	398
37.2	399	[[image:1675144608950-310.png]]
6.2	400
	401
47.1	402	=== 2.3.3 Battery Info ===
45.1	403
	404
6.2	405	Check the battery voltage for PS-LB.
	406
	407	Ex1: 0x0B45 = 2885mV
	408
	409	Ex2: 0x0B49 = 2889mV
	410
	411
47.1	412	=== 2.3.4 Probe Model ===
45.1	413
6.2	414
47.1	415	PS-LB has different kind of probe, 4~~20mA represent the full scale of the measuring range. So a 12mA output means different meaning for different probe.
6.2	416
	417
	418	For example.
	419
37.2	420	(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
47.1	421	\|Part Number\|Probe Used\|4~~20mA scale\|Example: 12mA meaning
	422	\|PS-LB-I3\|immersion type with 3 meters cable\|0~~3 meters\|1.5 meters pure water
	423	\|PS-LB-I5\|immersion type with 5 meters cable\|0~~5 meters\|2.5 meters pure water
	424	\|PS-LB-T20-B\|T20 threaded probe\|0~~1MPa\|0.5MPa air / gas or water pressure
6.2	425
47.1	426	The probe model field provides the convenient for server to identical how it should parse the 4~~20mA sensor value and get the correct value.
6.2	427
	428
47.1	429	=== 2.3.5 0~~20mA value (IDC_IN) ===
37.2	430
47.1	431
50.1	432	The output value from Pressure Probe, use together with Probe Model to get the pressure value or water level.
6.2	433
42.17	434	(% style="color:#037691" %)Example:
6.2	435
	436	27AE(H) = 10158 (D)/1000 = 10.158mA.
	437
	438
50.1	439	Instead of pressure probe, User can also connect a general 4~~20mA in this port to support different types of 4~~20mA sensors. below is the connection example:
	440
	441	[[image:image-20230225154759-1.png\|\|height="408" width="741"]]
	442
	443
47.1	444	=== 2.3.6 0~~30V value ( pin VDC_IN) ===
6.2	445
37.2	446
6.2	447	Measure the voltage value. The range is 0 to 30V.
	448
42.17	449	(% style="color:#037691" %)Example:
6.2	450
	451	138E(H) = 5006(D)/1000= 5.006V
	452
	453
47.1	454	=== 2.3.7 IN1&IN2&INT pin ===
6.2	455
37.2	456
6.2	457	IN1 and IN2 are used as digital input pins.
	458
42.17	459	(% style="color:#037691" %)Example:
6.2	460
42.17	461	09 (H): (0x09&0x08)>>3=1 IN1 pin is high level.
6.2	462
42.17	463	09 (H): (0x09&0x04)>>2=0 IN2 pin is low level.
6.2	464
	465
42.17	466	This data field shows if this packet is generated by (% style="color:blue" %)Interrupt Pin (%%)or not. [[Click here>>\|\|anchor="H3.2SetInterruptMode"]] for the hardware and software set up. Note: The Internet Pin is a separate pin in the screw terminal.
6.2	467
42.17	468	(% style="color:#037691" %)Example:
6.2	469
42.17	470	09 (H): (0x09&0x02)>>1=1 The level of the interrupt pin.
6.2	471
42.17	472	09 (H): 0x09&0x01=1 0x00: Normal uplink packet.
6.2	473
	474	0x01: Interrupt Uplink Packet.
	475
50.2	476
47.1	477	=== (% id="cke_bm_109176S" style="display:none" %) (%%)2.3.8 Sensor value, FPORT~=7 ===
6.2	478
47.1	479
	480	(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:508.222px" %)
	481	\|(% style="width:94px" %)(((
	482	Size(bytes)
	483	)))\|(% style="width:43px" %)2\|(% style="width:367px" %)n
	484	\|(% style="width:94px" %)Value\|(% style="width:43px" %)[[BAT>>\|\|anchor="H2.3.4BatteryInfo"]]\|(% style="width:367px" %)(((
	485	Voltage value, each 2 bytes is a set of voltage values.
	486	)))
	487
	488	[[image:image-20230220171300-1.png\|\|height="207" width="863"]]
	489
	490	Multiple sets of data collected are displayed in this form：
	491
48.1	492	[voltage value1], [voltage value2], [voltage value3],…[voltage value n/2]
47.1	493
	494
45.2	495	=== 2.3.9 Decode payload in The Things Network ===
6.2	496
	497
37.2	498	While using TTN network, you can add the payload format to decode the payload.
6.2	499
	500
37.2	501	[[image:1675144839454-913.png]]
6.2	502
	503
37.2	504	PS-LB TTN Payload Decoder: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]
6.2	505
	506
37.2	507	== 2.4 Uplink Interval ==
6.2	508
	509
37.3	510	The PS-LB by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H4.1ChangeUplinkInterval>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H4.1ChangeUplinkInterval\|\|style="background-color: rgb(255, 255, 255);"]]
6.2	511
	512
37.2	513	== 2.5 Show Data in DataCake IoT Server ==
6.2	514
	515
	516	[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
	517
	518
42.17	519	(% style="color:blue" %)Step 1: (%%)Be sure that your device is programmed and properly connected to the network at this time.
6.2	520
42.17	521	(% style="color:blue" %)Step 2:(%%) To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
6.2	522
	523
37.2	524	[[image:1675144951092-237.png]]
6.2	525
	526
37.2	527	[[image:1675144960452-126.png]]
6.2	528
	529
42.17	530	(% style="color:blue" %)Step 3:(%%) Create an account or log in Datacake.
6.2	531
42.18	532	(% style="color:blue" %)Step 4: (%%)Create PS-LB product.
6.2	533
37.2	534	[[image:1675145004465-869.png]]
6.2	535
	536
37.2	537	[[image:1675145018212-853.png]]
6.2	538
	539
	540
	541
37.2	542	[[image:1675145029119-717.png]]
6.2	543
	544
42.17	545	(% style="color:blue" %)Step 5: (%%)add payload decode
6.2	546
37.2	547	[[image:1675145051360-659.png]]
6.2	548
	549
37.2	550	[[image:1675145060812-420.png]]
6.2	551
	552
	553	After added, the sensor data arrive TTN, it will also arrive and show in Datacake.
	554
	555
37.2	556	[[image:1675145081239-376.png]]
6.2	557
	558
37.2	559	== 2.6 Frequency Plans ==
6.2	560
	561
	562	The PS-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
	563
37.3	564	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
6.2	565
	566
37.4	567	== 2.7 Firmware Change Log ==
6.2	568
	569
	570	Firmware download link:
	571
	572	[[https:~~/~~/www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0>>url:https://www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0]]
	573
	574
37.4	575	= 3. Configure PS-LB via AT Command or LoRaWAN Downlink =
6.2	576
37.4	577
6.2	578	Use can configure PS-LB via AT Command or LoRaWAN Downlink.
	579
42.18	580	* AT Command Connection: See [[FAQ>>\|\|anchor="H7.FAQ"]].
37.4	581	* LoRaWAN Downlink instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
6.2	582
	583	There are two kinds of commands to configure PS-LB, they are:
	584
42.32	585	* (% style="color:#037691" %)General Commands
6.2	586
	587	These commands are to configure:
	588
	589	* General system settings like: uplink interval.
	590	* LoRaWAN protocol & radio related command.
	591
	592	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
	593
37.5	594	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
6.2	595
	596
42.21	597	* (% style="color:#037691" %)Commands special design for PS-LB
6.2	598
	599	These commands only valid for PS-LB, as below:
	600
	601
37.5	602	== 3.1 Set Transmit Interval Time ==
6.2	603
37.5	604
6.2	605	Feature: Change LoRaWAN End Node Transmit Interval.
	606
42.21	607	(% style="color:blue" %)AT Command: AT+TDC
6.2	608
37.5	609	(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
42.25	610	\|=(% style="width: 156px;" %)Command Example\|=(% style="width: 137px;" %)Function\|=Response
	611	\|(% style="width:156px" %)AT+TDC=?\|(% style="width:137px" %)Show current transmit Interval\|(((
6.2	612	30000
	613	OK
	614	the interval is 30000ms = 30s
	615	)))
42.25	616	\|(% style="width:156px" %)AT+TDC=60000\|(% style="width:137px" %)Set Transmit Interval\|(((
6.2	617	OK
	618	Set transmit interval to 60000ms = 60 seconds
	619	)))
	620
42.21	621	(% style="color:blue" %)Downlink Command: 0x01
6.2	622
	623	Format: Command Code (0x01) followed by 3 bytes time value.
	624
43.2	625	If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
6.2	626
43.2	627	* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	628	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
6.2	629
52.2	630
	631
37.5	632	== 3.2 Set Interrupt Mode ==
6.2	633
37.5	634
6.2	635	Feature, Set Interrupt mode for GPIO_EXIT.
	636
42.21	637	(% style="color:blue" %)AT Command: AT+INTMOD
6.2	638
37.5	639	(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
43.2	640	\|=(% style="width: 154px;" %)Command Example\|=(% style="width: 196px;" %)Function\|=(% style="width: 157px;" %)Response
	641	\|(% style="width:154px" %)AT+INTMOD=?\|(% style="width:196px" %)Show current interrupt mode\|(% style="width:157px" %)(((
6.2	642	0
	643	OK
47.1	644	the mode is 0 =Disable Interrupt
6.2	645	)))
43.2	646	\|(% style="width:154px" %)AT+INTMOD=2\|(% style="width:196px" %)(((
6.2	647	Set Transmit Interval
47.1	648	0. (Disable Interrupt),
	649	~1. (Trigger by rising and falling edge)
	650	2. (Trigger by falling edge)
	651	3. (Trigger by rising edge)
43.2	652	)))\|(% style="width:157px" %)OK
6.2	653
42.21	654	(% style="color:blue" %)Downlink Command: 0x06
6.2	655
	656	Format: Command Code (0x06) followed by 3 bytes.
	657
	658	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
	659
43.2	660	* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	661	* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
6.2	662
50.2	663
52.2	664
37.5	665	== 3.3 Set the output time ==
	666
	667
6.2	668	Feature, Control the output 3V3 , 5V or 12V.
	669
42.21	670	(% style="color:blue" %)AT Command: AT+3V3T
6.2	671
42.30	672	(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:474px" %)
	673	\|=(% style="width: 154px;" %)Command Example\|=(% style="width: 201px;" %)Function\|=(% style="width: 116px;" %)Response
	674	\|(% style="width:154px" %)AT+3V3T=?\|(% style="width:201px" %)Show 3V3 open time.\|(% style="width:116px" %)(((
6.2	675	0
	676	OK
	677	)))
42.30	678	\|(% style="width:154px" %)AT+3V3T=0\|(% style="width:201px" %)Normally open 3V3 power supply.\|(% style="width:116px" %)(((
6.2	679	OK
	680	default setting
	681	)))
42.30	682	\|(% style="width:154px" %)AT+3V3T=1000\|(% style="width:201px" %)Close after a delay of 1000 milliseconds.\|(% style="width:116px" %)(((
6.2	683	OK
	684	)))
42.30	685	\|(% style="width:154px" %)AT+3V3T=65535\|(% style="width:201px" %)Normally closed 3V3 power supply.\|(% style="width:116px" %)(((
6.2	686	OK
	687	)))
	688
42.21	689	(% style="color:blue" %)AT Command: AT+5VT
6.2	690
42.30	691	(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:470px" %)
	692	\|=(% style="width: 155px;" %)Command Example\|=(% style="width: 196px;" %)Function\|=(% style="width: 114px;" %)Response
	693	\|(% style="width:155px" %)AT+5VT=?\|(% style="width:196px" %)Show 5V open time.\|(% style="width:114px" %)(((
6.2	694	0
	695	OK
	696	)))
42.30	697	\|(% style="width:155px" %)AT+5VT=0\|(% style="width:196px" %)Normally closed 5V power supply.\|(% style="width:114px" %)(((
6.2	698	OK
	699	default setting
	700	)))
42.30	701	\|(% style="width:155px" %)AT+5VT=1000\|(% style="width:196px" %)Close after a delay of 1000 milliseconds.\|(% style="width:114px" %)(((
6.2	702	OK
	703	)))
42.30	704	\|(% style="width:155px" %)AT+5VT=65535\|(% style="width:196px" %)Normally open 5V power supply.\|(% style="width:114px" %)(((
6.2	705	OK
	706	)))
	707
42.21	708	(% style="color:blue" %)AT Command: AT+12VT
6.2	709
42.29	710	(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:443px" %)
	711	\|=(% style="width: 156px;" %)Command Example\|=(% style="width: 199px;" %)Function\|=(% style="width: 83px;" %)Response
	712	\|(% style="width:156px" %)AT+12VT=?\|(% style="width:199px" %)Show 12V open time.\|(% style="width:83px" %)(((
6.2	713	0
	714	OK
	715	)))
42.29	716	\|(% style="width:156px" %)AT+12VT=0\|(% style="width:199px" %)Normally closed 12V power supply.\|(% style="width:83px" %)OK
	717	\|(% style="width:156px" %)AT+12VT=500\|(% style="width:199px" %)Close after a delay of 500 milliseconds.\|(% style="width:83px" %)(((
6.2	718	OK
	719	)))
	720
42.21	721	(% style="color:blue" %)Downlink Command: 0x07
6.2	722
	723	Format: Command Code (0x07) followed by 3 bytes.
	724
	725	The first byte is which power, the second and third bytes are the time to turn on.
	726
42.32	727	* Example 1: Downlink Payload: 070101F4 ~-~--> AT+3V3T=500
	728	* Example 2: Downlink Payload: 0701FFFF ~-~--> AT+3V3T=65535
	729	* Example 3: Downlink Payload: 070203E8 ~-~--> AT+5VT=1000
	730	* Example 4: Downlink Payload: 07020000 ~-~--> AT+5VT=0
	731	* Example 5: Downlink Payload: 070301F4 ~-~--> AT+12VT=500
	732	* Example 6: Downlink Payload: 07030000 ~-~--> AT+12VT=0
6.2	733
50.2	734
52.2	735
37.5	736	== 3.4 Set the Probe Model ==
	737
	738
47.1	739	Users need to configure this parameter according to the type of external probe. In this way, the server can decode according to this value, and convert the current value output by the sensor into water depth or pressure value.
6.2	740
47.1	741	AT Command: AT +PROBE
	742
	743	AT+PROBE=aabb
	744
	745	When aa=00, it is the water depth mode, and the current is converted into the water depth value; bb is the probe at a depth of several meters.
	746
	747	When aa=01, it is the pressure mode, which converts the current into a pressure value;
	748
	749	bb represents which type of pressure sensor it is.
	750
	751	(A->01,B->02,C->03,D->04,E->05,F->06,G->07,H->08,I->09,J->0A,K->0B,L->0C)
	752
	753	(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
	754	\|Command Example\|Function\|Response
	755	\|AT +PROBE =?\|Get or Set the probe model.\|0
6.2	756	OK
47.1	757	\|AT +PROBE =0003\|Set water depth sensor mode, 3m type.\|OK
	758	\|(((
	759	AT +PROBE =000A
6.2	760
47.1	761
	762	)))\|Set water depth sensor mode, 10m type.\|OK
	763	\|AT +PROBE =0101\|Set pressure transmitters mode, first type(A).\|OK
	764	\|AT +PROBE =0000\|Initial state, no settings.\|OK
6.2	765
47.1	766	Downlink Command: 0x08
	767
6.2	768	Format: Command Code (0x08) followed by 2 bytes.
	769
47.1	770	* Example 1: Downlink Payload: 080003 ~-~--> AT+PROBE=0003
	771	* Example 2: Downlink Payload: 080101 ~-~--> AT+PROBE=0101
6.2	772
50.2	773
52.2	774
45.1	775	== 3.5 Multiple collections are one uplink（Since firmware V1.1） ==
43.3	776
45.2	777
45.1	778	Added AT+STDC command to collect the voltage of VDC_INPUT multiple times and upload it at one time.
	779
	780	(% style="color:blue" %)AT Command: AT +STDC
	781
47.1	782	AT+STDC=aa,bb,bb
	783
	784	(% style="color:#037691" %)aa:(%%)
	785	0: means disable this function and use TDC to send packets.
	786	1: means enable this function, use the method of multiple acquisitions to send packets.
	787	(% style="color:#037691" %)bb:(%%) Each collection interval (s), the value is 1~~65535
	788	(% style="color:#037691" %)cc:(%%) the number of collection times, the value is 1~~120
	789
45.1	790	(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
47.1	791	\|Command Example\|Function\|Response
	792	\|AT+STDC=?\|Get the mode of multiple acquisitions and one uplink.\|1,10,18
45.1	793	OK
47.1	794	\|AT+STDC=1,10,18\|Set the mode of multiple acquisitions and one uplink, collect once every 10 seconds, and report after 18 times.\|(((
	795	Attention:Take effect after ATZ
	796
	797	OK
45.1	798	)))
47.1	799	\|AT+STDC=0, 0,0\|(((
	800	Use the TDC interval to send packets.(default)
	801
	802
	803	)))\|(((
	804	Attention:Take effect after ATZ
	805
45.1	806	OK
	807	)))
	808
	809	(% style="color:blue" %)Downlink Command: 0xAE
	810
	811	Format: Command Code (0x08) followed by 5 bytes.
	812
45.3	813	* Example 1: Downlink Payload: AE 01 02 58 12 ~-~--> AT+STDC=1,600,18
45.1	814
50.2	815
52.2	816
37.6	817	= 4. Battery & how to replace =
6.2	818
37.6	819	== 4.1 Battery Type ==
	820
	821
38.2	822	PS-LB is equipped with a [[8500mAH ER26500 Li-SOCI2 battery>>https://www.dropbox.com/sh/w9l2oa3ytpculph/AAAPtt-apH4lYfCj-2Y6lHvQa?dl=0]]. The battery is un-rechargeable battery with low discharge rate targeting for 8~~10 years use. This type of battery is commonly used in IoT target for long-term running, such as water meter.
6.2	823
	824	The discharge curve is not linear so can’t simply use percentage to show the battery level. Below is the battery performance.
	825
38.2	826	[[image:1675146710956-626.png]]
6.2	827
	828
	829	Minimum Working Voltage for the PS-LB:
	830
	831	PS-LB: 2.45v ~~ 3.6v
	832
	833
38.2	834	== 4.2 Replace Battery ==
6.2	835
38.2	836
6.2	837	Any battery with range 2.45 ~~ 3.6v can be a replacement. We recommend to use Li-SOCl2 Battery.
	838
	839	And make sure the positive and negative pins match.
	840
	841
40.2	842	== 4.3 Power Consumption Analyze ==
6.2	843
	844
	845	Dragino Battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
	846
	847	Instruction to use as below:
	848
42.32	849	(% style="color:blue" %)Step 1:(%%) Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dropbox.com/sh/zwex6i331j5oeq2/AACIMf9f_v2qsJ39CuMQ5Py_a?dl=0>>https://www.dropbox.com/sh/zwex6i331j5oeq2/AACIMf9f_v2qsJ39CuMQ5Py_a?dl=0]]
6.2	850
42.21	851	(% style="color:blue" %)Step 2:(%%) Open it and choose
6.2	852
	853	* Product Model
	854	* Uplink Interval
	855	* Working Mode
	856
	857	And the Life expectation in difference case will be shown on the right.
	858
40.2	859	[[image:1675146895108-304.png]]
6.2	860
	861
	862	The battery related documents as below:
	863
40.2	864	* [[Battery Dimension>>https://www.dropbox.com/s/ox5g9njwjle7aw3/LSN50-Battery-Dimension.pdf?dl=0]],
	865	* [[Lithium-Thionyl Chloride Battery datasheet, Tech Spec>>https://www.dropbox.com/sh/d4oyfnp8o94180o/AABQewCNSh5GPeQH86UxRgQQa?dl=0]]
	866	* [[Lithium-ion Battery-Capacitor datasheet>>https://www.dropbox.com/s/791gjes2lcbfi1p/SPC_1520_datasheet.jpg?dl=0]], [[Tech Spec>>https://www.dropbox.com/s/4pkepr9qqqvtzf2/SPC1520%20Technical%20Specification20171123.pdf?dl=0]]
6.2	867
40.2	868	[[image:image-20230131145708-3.png]]
6.2	869
	870
40.4	871	=== 4.3.1 Battery Note ===
6.2	872
	873
	874	The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
	875
	876
40.4	877	=== 4.3.2 Replace the battery ===
6.2	878
	879
40.4	880	You can change the battery in the PS-LB.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won't be voltage drop between battery and main board.
6.2	881
40.4	882	The default battery pack of PS-LB includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
6.2	883
	884
40.5	885	= 5. Remote Configure device =
6.2	886
42.3	887	== 5.1 Connect via BLE ==
6.2	888
	889
42.2	890	Please see this instruction for how to configure via BLE: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]]
42.3	891
	892
42.2	893	== 5.2 AT Command Set ==
6.2	894
	895
	896
42.2	897	= 6. OTA firmware update =
6.2	898
	899
42.2	900	Please see this link for how to do OTA firmware update: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
6.2	901
	902
42.2	903	= 7. FAQ =
6.2	904
52.1	905	== 7.1 How to use AT Command via UART to access device? ==
6.2	906
	907
42.2	908	See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
6.2	909
	910
42.2	911	== 7.2 How to update firmware via UART port? ==
6.2	912
	913
42.2	914	See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
6.2	915
	916
42.2	917	== 7.3 How to change the LoRa Frequency Bands/Region? ==
6.2	918
	919
42.3	920	You can follow the instructions for [[how to upgrade image>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]].
6.2	921	When downloading the images, choose the required image file for download.
	922
	923
42.2	924	= 8. Order Info =
6.2	925
	926
42.2	927	[[image:image-20230131153105-4.png]]
6.2	928
	929
42.2	930	= 9. Packing Info =
6.2	931
	932
42.21	933	(% style="color:#037691" %)Package Includes:
6.2	934
	935	* PS-LB LoRaWAN Pressure Sensor
	936
42.21	937	(% style="color:#037691" %)Dimension and weight:
6.2	938
	939	* Device Size: cm
	940	* Device Weight: g
	941	* Package Size / pcs : cm
	942	* Weight / pcs : g
	943
50.2	944
52.2	945
42.2	946	= 10. Support =
6.2	947
42.2	948
6.2	949	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
42.20	950
42.2	951	* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
6.2	952
40.4	953

Wiki source code of PS-LB -- LoRaWAN Air Water Pressure Sensor User Manual

Applications

Navigation