Last modified by Xiaoling on 2025/04/27 10:31
<
From version < 53.28 >
edited by Xiaoling
on 2023/04/17 14:01
To version < 42.16 >
edited by Xiaoling
on 2023/01/31 16:11
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -16,33 +16,22 @@
16 16  == 1.1 What is LoRaWAN Pressure Sensor ==
17 17  
18 18  
19 -(((
20 -The Dragino PS-LB series sensors are (% style="color:blue" %)**LoRaWAN Pressure Sensor**(%%) for Internet of Things solution. PS-LB can measure Air, Water pressure and liquid level and upload the sensor data via wireless to LoRaWAN IoT server.
21 -)))
19 +The Dragino PS-LB series sensors are **(% style="color:blue" %)LoRaWAN Pressure Sensor**(%%) for Internet of Things solution. PS-LB can measure Air, Water pressure and liquid level and upload the sensor data via wireless to LoRaWAN IoT server.
22 22  
23 -(((
24 -The PS-LB series sensors include (% style="color:blue" %)**Thread Installation Type**(%%) and (% style="color:blue" %)**Immersion Type**(%%), it supports different pressure range which can be used for different measurement requirement.
25 -)))
21 +The PS-LB series sensors include **(% style="color:blue" %)Thread Installation Type**(%%) and **(% style="color:blue" %)Immersion Type**(%%), it supports different pressure range which can be used for different measurement requirement.
26 26  
27 -(((
28 28  The LoRa wireless technology used in PS-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
29 -)))
30 30  
31 -(((
32 32  PS-LB supports BLE configure and wireless OTA update which make user easy to use.
33 -)))
34 34  
35 -(((
36 -PS-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
37 -)))
27 +PS-LB is powered by **(% style="color:blue" %)8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
38 38  
39 -(((
40 40  Each PS-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
41 -)))
42 42  
43 43  [[image:1675071321348-194.png]]
44 44  
45 45  
34 +
46 46  == 1.2 ​Features ==
47 47  
48 48  
... ... @@ -58,25 +58,23 @@
58 58  * Uplink on periodically
59 59  * Downlink to change configure
60 60  * 8500mAh Battery for long term use
61 -* Controllable 3.3v,5v and 12v output to power external sensor
62 62  
63 63  
64 -
65 65  == 1.3 Specification ==
66 66  
67 67  
68 -(% style="color:#037691" %)**Micro Controller:**
55 +**(% style="color:#037691" %)Micro Controller:**
69 69  
70 70  * MCU: 48Mhz ARM
71 71  * Flash: 256KB
72 72  * RAM: 64KB
73 73  
74 -(% style="color:#037691" %)**Common DC Characteristics:**
61 +**(% style="color:#037691" %)Common DC Characteristics:**
75 75  
76 76  * Supply Voltage: 2.5v ~~ 3.6v
77 77  * Operating Temperature: -40 ~~ 85°C
78 78  
79 -(% style="color:#037691" %)**LoRa Spec:**
66 +**(% style="color:#037691" %)LoRa Spec:**
80 80  
81 81  * Frequency Range,  Band 1 (HF): 862 ~~ 1020 Mhz
82 82  * Max +22 dBm constant RF output vs.
... ... @@ -83,19 +83,19 @@
83 83  * RX sensitivity: down to -139 dBm.
84 84  * Excellent blocking immunity
85 85  
86 -(% style="color:#037691" %)**Current Input Measuring :**
73 +**(% style="color:#037691" %)Current Input Measuring :**
87 87  
88 88  * Range: 0 ~~ 20mA
89 89  * Accuracy: 0.02mA
90 90  * Resolution: 0.001mA
91 91  
92 -(% style="color:#037691" %)**Voltage Input Measuring:**
79 +**(% style="color:#037691" %)Voltage Input Measuring:**
93 93  
94 94  * Range: 0 ~~ 30v
95 95  * Accuracy: 0.02v
96 96  * Resolution: 0.001v
97 97  
98 -(% style="color:#037691" %)**Battery:**
85 +**(% style="color:#037691" %)Battery:**
99 99  
100 100  * Li/SOCI2 un-chargeable battery
101 101  * Capacity: 8500mAh
... ... @@ -103,13 +103,12 @@
103 103  * Max continuously current: 130mA
104 104  * Max boost current: 2A, 1 second
105 105  
106 -(% style="color:#037691" %)**Power Consumption**
93 +**(% style="color:#037691" %)Power Consumption**
107 107  
108 108  * Sleep Mode: 5uA @ 3.3v
109 109  * LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
110 110  
111 111  
112 -
113 113  == 1.4 Probe Types ==
114 114  
115 115  === 1.4.1 Thread Installation Type ===
... ... @@ -129,7 +129,6 @@
129 129  * Connector Type: Various Types, see order info
130 130  
131 131  
132 -
133 133  === 1.4.2 Immersion Type ===
134 134  
135 135  
... ... @@ -139,22 +139,25 @@
139 139  * Measuring Range: Measure range can be customized, up to 100m.
140 140  * Accuracy: 0.2% F.S
141 141  * Long-Term Stability: ±0.2% F.S / Year
127 +* Overload 200% F.S
128 +* Zero Temperature Drift: ±2% F.S)
129 +* FS Temperature Drift: ±2% F.S
142 142  * Storage temperature: -30℃~~80℃
143 -* Operating temperature: 0℃~~50℃
131 +* Operating temperature: -40℃~~85℃
144 144  * Material: 316 stainless steels
145 145  
146 146  
147 -
148 148  == 1.5 Probe Dimension ==
149 149  
150 150  
151 151  
139 +
152 152  == 1.6 Application and Installation ==
153 153  
154 154  === 1.6.1 Thread Installation Type ===
155 155  
156 156  
157 -(% style="color:blue" %)**Application:**
145 +**(% style="color:blue" %)Application:**
158 158  
159 159  * Hydraulic Pressure
160 160  * Petrochemical Industry
... ... @@ -172,7 +172,7 @@
172 172  === 1.6.2 Immersion Type ===
173 173  
174 174  
175 -(% style="color:blue" %)**Application:**
163 +**(% style="color:blue" %)Application:**
176 176  
177 177  Liquid & Water Pressure / Level detect.
178 178  
... ... @@ -191,9 +191,9 @@
191 191  == 1.7 Sleep mode and working mode ==
192 192  
193 193  
194 -(% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
182 +**(% style="color:blue" %)Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
195 195  
196 -(% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
184 +**(% style="color:blue" %)Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
197 197  
198 198  
199 199  == 1.8 Button & LEDs ==
... ... @@ -202,18 +202,21 @@
202 202  [[image:1675071855856-879.png]]
203 203  
204 204  
205 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
206 -|=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)**Action**
207 -|(% style="background-color:#f2f2f2; width:167px" %)Pressing ACT between 1s < time < 3s|(% style="background-color:#f2f2f2; width:117px" %)Send an uplink|(% style="background-color:#f2f2f2; width:225px" %)(((
208 -If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.
193 +(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
194 +|(% style="width:138px" %)**Behavior on ACT**|(% style="width:100px" %)**Function**|**Action**
195 +|(% style="width:138px" %)Pressing ACT between 1s < time < 3s|(% style="width:100px" %)Send an uplink|(((
196 +If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, **(% style="color:blue" %)blue led** (%%)will blink once.
197 +
209 209  Meanwhile, BLE module will be active and user can connect via BLE to configure device.
210 210  )))
211 -|(% style="background-color:#f2f2f2; width:167px" %)Pressing ACT for more than 3s|(% style="background-color:#f2f2f2; width:117px" %)Active Device|(% style="background-color:#f2f2f2; width:225px" %)(((
212 -(% style="background-color:#f2f2f2; color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
213 -(% style="background-color:#f2f2f2; color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
200 +|(% style="width:138px" %)Pressing ACT for more than 3s|(% style="width:100px" %)Active Device|(((
201 +**(% style="color:green" %)Green led**(%%) will fast blink 5 times, device will enter **(% style="color:#037691" %)OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
202 +
203 +**(% style="color:green" %)Green led**(%%) will solidly turn on for 5 seconds after joined in network.
204 +
214 214  Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
215 215  )))
216 -|(% style="background-color:#f2f2f2; width:167px" %)Fast press ACT 5 times.|(% style="background-color:#f2f2f2; width:117px" %)Deactivate Device|(% style="background-color:#f2f2f2; width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means PS-LB-NA is in Deep Sleep Mode.
207 +|(% style="width:138px" %)Fast press ACT 5 times.|(% style="width:100px" %)Deactivate Device|red led will solid on for 5 seconds. Means PS-LB is in Deep Sleep Mode.
217 217  
218 218  
219 219  
... ... @@ -241,6 +241,8 @@
241 241  == 1.11 Mechanical ==
242 242  
243 243  
235 +
236 +
244 244  [[image:1675143884058-338.png]]
245 245  
246 246  
... ... @@ -255,9 +255,10 @@
255 255  == 2.1 How it works ==
256 256  
257 257  
258 -The PS-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and activate the PS-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
251 +The PS-LB is configured as **(% style="color:#037691" %)LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and activate the PS-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
259 259  
260 260  
254 +
261 261  == 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
262 262  
263 263  
... ... @@ -270,7 +270,7 @@
270 270  The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
271 271  
272 272  
273 -(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from PS-LB.
267 +**(% style="color:blue" %)Step 1:**(%%) Create a device in TTN with the OTAA keys from PS-LB.
274 274  
275 275  Each PS-LB is shipped with a sticker with the default device EUI as below:
276 276  
... ... @@ -281,38 +281,48 @@
281 281  You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
282 282  
283 283  
284 -(% style="color:blue" %)**Register the device**
278 +**(% style="color:blue" %)Register the device**
285 285  
286 286  [[image:1675144099263-405.png]]
287 287  
288 288  
289 -(% style="color:blue" %)**Add APP EUI and DEV EUI**
283 +**(% style="color:blue" %)Add APP EUI and DEV EUI**
290 290  
291 291  [[image:1675144117571-832.png]]
292 292  
293 293  
294 -(% style="color:blue" %)**Add APP EUI in the application**
288 +**(% style="color:blue" %)Add APP EUI in the application**
295 295  
296 296  
297 297  [[image:1675144143021-195.png]]
298 298  
299 299  
300 -(% style="color:blue" %)**Add APP KEY**
294 +**(% style="color:blue" %)Add APP KEY**
301 301  
302 302  [[image:1675144157838-392.png]]
303 303  
304 -(% style="color:blue" %)**Step 2:**(%%) Activate on PS-LB
298 +**(% style="color:blue" %)Step 2:**(%%) Activate on PS-LB
305 305  
306 306  
307 307  Press the button for 5 seconds to activate the PS-LB.
308 308  
309 -(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
303 +**(% style="color:green" %)Green led**(%%) will fast blink 5 times, device will enter **(% style="color:blue" %)OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. **(% style="color:green" %)Green led**(%%) will solidly turn on for 5 seconds after joined in network.
310 310  
311 311  After join success, it will start to upload messages to TTN and you can see the messages in the panel.
312 312  
313 313  
308 +
314 314  == 2.3 ​Uplink Payload ==
315 315  
311 +
312 +Uplink payloads have two types:
313 +
314 +* Distance Value: Use FPORT=2
315 +* Other control commands: Use other FPORT fields.
316 +
317 +The application server should parse the correct value based on FPORT settings.
318 +
319 +
316 316  === 2.3.1 Device Status, FPORT~=5 ===
317 317  
318 318  
... ... @@ -321,10 +321,10 @@
321 321  Users can also use the downlink command(0x26 01) to ask PS-LB to resend this uplink.
322 322  
323 323  
324 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
325 -|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**
326 -|(% style="background-color:#f2f2f2; width:103px" %)**Size (bytes)**|(% style="background-color:#f2f2f2; width:72px" %)**1**|(% style="background-color:#f2f2f2" %)**2**|(% style="background-color:#f2f2f2; width:91px" %)**1**|(% style="background-color:#f2f2f2; width:86px" %)**1**|(% style="background-color:#f2f2f2; width:44px" %)**2**
327 -|(% style="background-color:#f2f2f2; width:103px" %)**Value**|(% style="background-color:#f2f2f2; width:72px" %)Sensor Model|(% style="background-color:#f2f2f2" %)Firmware Version|(% style="background-color:#f2f2f2; width:91px" %)Frequency Band|(% style="background-color:#f2f2f2; width:86px" %)Sub-band|(% style="background-color:#f2f2f2; width:44px" %)BAT
328 +(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
329 +|(% colspan="6" %)**Device Status (FPORT=5)**
330 +|(% style="width:103px" %)**Size (bytes)**|(% style="width:72px" %)**1**|**2**|**1**|**1**|**2**
331 +|(% style="width:103px" %)**Value**|(% style="width:72px" %)Sensor Model|Firmware Version|Frequency Band|Sub-band|BAT
328 328  
329 329  Example parse in TTNv3
330 330  
... ... @@ -331,11 +331,11 @@
331 331  [[image:1675144504430-490.png]]
332 332  
333 333  
334 -(% style="color:#037691" %)**Sensor Model**(%%): For PS-LB, this value is 0x16
338 +**(% style="color:#037691" %)Sensor Model**(%%): For PS-LB, this value is 0x16
335 335  
336 -(% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
340 +**(% style="color:#037691" %)Firmware Version**(%%): 0x0100, Means: v1.0.0 version
337 337  
338 -(% style="color:#037691" %)**Frequency Band**:
342 +**(% style="color:#037691" %)Frequency Band**:
339 339  
340 340  *0x01: EU868
341 341  
... ... @@ -366,7 +366,7 @@
366 366  *0x0e: MA869
367 367  
368 368  
369 -(% style="color:#037691" %)**Sub-Band**:
373 +**(% style="color:#037691" %)Sub-Band**:
370 370  
371 371  AU915 and US915:value 0x00 ~~ 0x08
372 372  
... ... @@ -375,7 +375,7 @@
375 375  Other Bands: Always 0x00
376 376  
377 377  
378 -(% style="color:#037691" %)**Battery Info**:
382 +**(% style="color:#037691" %)Battery Info**:
379 379  
380 380  Check the battery voltage.
381 381  
... ... @@ -390,15 +390,16 @@
390 390  Uplink payload includes in total 9 bytes.
391 391  
392 392  
393 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
394 -|(% style="background-color:#d9e2f3; width:97px" %)(((
397 +(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
398 +|(% style="width:97px" %)(((
395 395  **Size(bytes)**
396 -)))|(% style="background-color:#d9e2f3; width:48px" %)**2**|(% style="background-color:#d9e2f3; width:71px" %)**2**|(% style="background-color:#d9e2f3; width:98px" %)**2**|(% style="background-color:#d9e2f3; width:73px" %)**2**|(% style="background-color:#d9e2f3; width:122px" %)**1**
397 -|(% style="width:97px" %)**Value**|(% style="width:48px" %)[[BAT>>||anchor="H2.3.3BatteryInfo"]]|(% style="width:71px" %)[[Probe Model>>||anchor="H2.3.4ProbeModel"]]|(% style="width:98px" %)[[0 ~~~~ 20mA value>>||anchor="H2.3.507E20mAvalue28IDC_IN29"]]|(% style="width:73px" %)[[0 ~~~~ 30v value>>||anchor="H2.3.607E30Vvalue28pinVDC_IN29"]]|(% style="width:122px" %)[[IN1 &IN2 Interrupt  flag>>||anchor="H2.3.7IN126IN226INTpin"]]
400 +)))|(% style="width:48px" %)**2**|(% style="width:58px" %)**2**|**2**|**2**|**1**
401 +|(% style="width:97px" %)**Value**|(% style="width:48px" %)[[BAT>>||anchor="H2.3.3BatteryInfo"]]|(% style="width:58px" %)[[Probe Model>>||anchor="H2.3.4ProbeModel"]]|[[0 ~~~~ 20mA value>>||anchor="H2.3.507E20mAvalue28IDC_IN29"]]|[[0 ~~~~ 30v value>>||anchor="H2.3.607E30Vvalue28pinVDC_IN29"]]|[[IN1 &IN2 Interrupt  flag>>||anchor="H2.3.7IN126IN226INTpin"]]
398 398  
399 399  [[image:1675144608950-310.png]]
400 400  
401 401  
406 +
402 402  === 2.3.3 Battery Info ===
403 403  
404 404  
... ... @@ -412,41 +412,35 @@
412 412  === 2.3.4 Probe Model ===
413 413  
414 414  
415 -PS-LB has different kind of probe, 4~~20mA represent the full scale of the measuring range. So a 12mA output means different meaning for different probe. 
420 +PS-LB has different kind of probe, 0~~20mA represent the full scale of the measuring range. So a 15mA output means different meaning for different probe. 
416 416  
417 417  
418 -**For example.**
423 +For example.
419 419  
420 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
421 -|(% style="background-color:#d9e2f3; color:#0070c0" %)**Part Number**|(% style="background-color:#d9e2f3; color:#0070c0" %)**Probe Used**|(% style="background-color:#d9e2f3; color:#0070c0" %)**4~~20mA scale**|(% style="background-color:#d9e2f3; color:#0070c0" %)**Example: 12mA meaning**
422 -|(% style="background-color:#f2f2f2" %)PS-LB-I3|(% style="background-color:#f2f2f2" %)immersion type with 3 meters cable|(% style="background-color:#f2f2f2" %)0~~3 meters|(% style="background-color:#f2f2f2" %)1.5 meters pure water
423 -|(% style="background-color:#f2f2f2" %)PS-LB-I5|(% style="background-color:#f2f2f2" %)immersion type with 5 meters cable|(% style="background-color:#f2f2f2" %)0~~5 meters|(% style="background-color:#f2f2f2" %)2.5 meters pure water
424 -|(% style="background-color:#f2f2f2" %)PS-LB-T20-B|(% style="background-color:#f2f2f2" %)T20 threaded probe|(% style="background-color:#f2f2f2" %)0~~1MPa|(% style="background-color:#f2f2f2" %)0.5MPa air / gas or water pressure
425 +(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
426 +|(% style="width:111px" %)**Part Number**|(% style="width:158px" %)**Probe Used**|**0~~20mA scale**|**Example: 10mA meaning**
427 +|(% style="width:111px" %)PS-LB-I3|(% style="width:158px" %)immersion type with 3 meters cable|0~~3 meters|1.5 meters pure water
428 +|(% style="width:111px" %)PS-LB-I5|(% style="width:158px" %)immersion type with 5 meters cable|0~~5 meters|2.5 meters pure water
425 425  
426 -The probe model field provides the convenient for server to identical how it should parse the 4~~20mA sensor value and get the correct value.
430 +The probe model field provides the convenient for server to identical how it should parse the 0~~20mA sensor value and get the correct value.
427 427  
428 428  
429 429  === 2.3.5 0~~20mA value (IDC_IN) ===
430 430  
431 431  
432 -The output value from **Pressure Probe**, use together with Probe Model to get the pressure value or water level.
436 +The output value from Pressure Probe, use together with Probe Model to get the pressure value or water level.
433 433  
434 -(% style="color:#037691" %)**Example**:
438 +**(% style="color:#037691" %)Example**:
435 435  
436 436  27AE(H) = 10158 (D)/1000 = 10.158mA.
437 437  
438 438  
439 -Instead of pressure probe, User can also connect a general 4~~20mA in this port to support different types of 4~~20mA sensors. below is the connection example:
440 -
441 -[[image:image-20230225154759-1.png||height="408" width="741"]]
442 -
443 -
444 444  === 2.3.6 0~~30V value ( pin VDC_IN) ===
445 445  
446 446  
447 447  Measure the voltage value. The range is 0 to 30V.
448 448  
449 -(% style="color:#037691" %)**Example**:
448 +**(% style="color:#037691" %)Example**:
450 450  
451 451  138E(H) = 5006(D)/1000= 5.006V
452 452  
... ... @@ -456,45 +456,27 @@
456 456  
457 457  IN1 and IN2 are used as digital input pins.
458 458  
459 -(% style="color:#037691" %)**Example**:
458 +**(% style="color:#037691" %)Example**:
460 460  
461 -09 (H): (0x09&0x08)>>3=1    IN1 pin is high level.
460 +09 (H):(0x09&0x08)>>3=1    IN1 pin is high level.
462 462  
463 -09 (H): (0x09&0x04)>>2=0    IN2 pin is low level.
462 +09 (H):(0x09&0x04)>>2=0    IN2 pin is low level.
464 464  
465 465  
466 -This data field shows if this packet is generated by (% style="color:blue" %)**Interrupt Pin** (%%)or not. [[Click here>>||anchor="H3.3.2SetInterruptMode"]] for the hardware and software set up. Note: The Internet Pin is a separate pin in the screw terminal.
465 +This data field shows if this packet is generated by **(% style="color:blue" %)Interrupt Pin** (%%)or not. [[Click here>>||anchor="H3.2SetInterruptMode"]] for the hardware and software set up. Note: The Internet Pin is a separate pin in the screw terminal.
467 467  
468 -(% style="color:#037691" %)**Example:**
467 +**(% style="color:#037691" %)Example:**
469 469  
470 -09 (H): (0x09&0x02)>>1=1    The level of the interrupt pin.
469 +09 (H):(0x09&0x02)>>1=1    The level of the interrupt pin.
471 471  
472 -09 (H): 0x09&0x01=1              0x00: Normal uplink packet.
471 +09 (H):0x09&0x01=1              0x00: Normal uplink packet.
473 473  
474 474  0x01: Interrupt Uplink Packet.
475 475  
476 476  
477 -=== (% id="cke_bm_109176S" style="display:none" %) (%%)2.3.8 Sensor value, FPORT~=7 ===
476 +=== 2.3.8 ​Decode payload in The Things Network ===
478 478  
479 479  
480 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:508.222px" %)
481 -|(% style="background-color:#d9e2f3; width:94px" %)(((
482 -**Size(bytes)**
483 -)))|(% style="background-color:#d9e2f3; width:43px" %)2|(% style="background-color:#d9e2f3; width:367px" %)n
484 -|(% style="width:94px" %)**Value**|(% style="width:43px" %)[[BAT>>||anchor="H2.3.3BatteryInfo"]]|(% style="width:367px" %)(((
485 -Voltage value, each 2 bytes is a set of voltage values.
486 -)))
487 -
488 -[[image:image-20230220171300-1.png||height="207" width="863"]]
489 -
490 -Multiple sets of data collected are displayed in this form：
491 -
492 -[voltage value1], [voltage value2], [voltage value3],…[voltage value n/2]
493 -
494 -
495 -=== 2.3.9 ​Decode payload in The Things Network ===
496 -
497 -
498 498  While using TTN network, you can add the payload format to decode the payload.
499 499  
500 500  
... ... @@ -516,9 +516,9 @@
516 516  [[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
517 517  
518 518  
519 -(% style="color:blue" %)**Step 1: **(%%)Be sure that your device is programmed and properly connected to the network at this time.
500 +**(% style="color:blue" %)Step 1: **(%%)Be sure that your device is programmed and properly connected to the network at this time.
520 520  
521 -(% style="color:blue" %)**Step 2:**(%%) To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
502 +**(% style="color:blue" %)Step 2:**(%%) To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
522 522  
523 523  
524 524  [[image:1675144951092-237.png]]
... ... @@ -527,9 +527,9 @@
527 527  [[image:1675144960452-126.png]]
528 528  
529 529  
530 -(% style="color:blue" %)**Step 3:**(%%) Create an account or log in Datacake.
511 +**(% style="color:blue" %)Step 3:**(%%) Create an account or log in Datacake.
531 531  
532 -(% style="color:blue" %)**Step 4:** (%%)Create PS-LB product.
513 +**(% style="color:#blue" %)Step 4:** (%%)Create PS-LB product.
533 533  
534 534  [[image:1675145004465-869.png]]
535 535  
... ... @@ -542,7 +542,7 @@
542 542  [[image:1675145029119-717.png]]
543 543  
544 544  
545 -(% style="color:blue" %)**Step 5: **(%%)add payload decode
526 +**(% style="color:blue" %)Step 5: **(%%)add payload decode
546 546  
547 547  [[image:1675145051360-659.png]]
548 548  
... ... @@ -550,6 +550,7 @@
550 550  [[image:1675145060812-420.png]]
551 551  
552 552  
534 +
553 553  After added, the sensor data arrive TTN, it will also arrive and show in Datacake.
554 554  
555 555  
... ... @@ -572,282 +572,335 @@
572 572  [[https:~~/~~/www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0>>url:https://www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0]]
573 573  
574 574  
575 -= 3. Configure PS-LB =
576 576  
577 -== 3.1 Configure Methods ==
558 += 3. Configure PS-LB via AT Command or LoRaWAN Downlink =
578 578  
579 579  
580 -PS-LB-NA supports below configure method:
561 +Use can configure PS-LB via AT Command or LoRaWAN Downlink.
581 581  
582 -* AT Command via Bluetooth Connection (**Recommand Way**): [[BLE Configure Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
583 -* AT Command via UART Connection : See [[FAQ>>||anchor="H6.FAQ"]].
584 -* LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>url:http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
563 +* AT Command Connection: See [[FAQ>>path:#AT_COMMAND]].
564 +* LoRaWAN Downlink instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
585 585  
586 586  
567 +There are two kinds of commands to configure PS-LB, they are:
587 587  
588 -== 3.2 General Commands ==
569 +* **General Commands**.
589 589  
590 -
591 591  These commands are to configure:
592 592  
593 593  * General system settings like: uplink interval.
594 594  * LoRaWAN protocol & radio related command.
595 595  
596 -They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
576 +They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
597 597  
598 -[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
578 +[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
599 599  
600 600  
601 -== 3.3 Commands special design for PS-LB ==
581 +* **Commands special design for PS-LB**
602 602  
603 -
604 604  These commands only valid for PS-LB, as below:
605 605  
606 606  
607 -=== 3.3.1 Set Transmit Interval Time ===
586 +== 3.1 Set Transmit Interval Time ==
608 608  
609 609  
610 610  Feature: Change LoRaWAN End Node Transmit Interval.
611 611  
612 -(% style="color:blue" %)**AT Command: AT+TDC**
591 +**AT Command: AT+TDC**
613 613  
614 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
615 -|=(% style="width: 160px; background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 160px; background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 190px;background-color:#D9E2F3;color:#0070C0" %)**Response**
616 -|(% style="background-color:#f2f2f2; width:157px" %)AT+TDC=?|(% style="background-color:#f2f2f2; width:166px" %)Show current transmit Interval|(% style="background-color:#f2f2f2" %)(((
593 +(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
594 +|**Command Example**|**Function**|**Response**
595 +|AT+TDC=?|Show current transmit Interval|(((
617 617  30000
597 +
618 618  OK
599 +
619 619  the interval is 30000ms = 30s
620 620  )))
621 -|(% style="background-color:#f2f2f2; width:157px" %)AT+TDC=60000|(% style="background-color:#f2f2f2; width:166px" %)Set Transmit Interval|(% style="background-color:#f2f2f2" %)(((
602 +|AT+TDC=60000|Set Transmit Interval|(((
622 622  OK
604 +
623 623  Set transmit interval to 60000ms = 60 seconds
624 624  )))
625 625  
626 -(% style="color:blue" %)**Downlink Command: 0x01**
608 +**Downlink Command: 0x01**
627 627  
628 628  Format: Command Code (0x01) followed by 3 bytes time value.
629 629  
630 -If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
612 +If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
631 631  
632 -* Example 1: Downlink Payload: 0100001E  ~/~/  Set Transmit Interval (TDC) = 30 seconds
633 -* Example 2: Downlink Payload: 0100003C  ~/~/  Set Transmit Interval (TDC) = 60 seconds
614 +* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
615 +* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
634 634  
635 635  
618 +== 3.2 Set Interrupt Mode ==
636 636  
637 -=== 3.3.2 Set Interrupt Mode ===
638 638  
639 -
640 640  Feature, Set Interrupt mode for GPIO_EXIT.
641 641  
642 -(% style="color:blue" %)**AT Command: AT+INTMOD**
623 +**AT Command: AT+INTMOD**
643 643  
644 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
645 -|=(% style="width: 154px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3;color:#0070C0" %)**Response**
646 -|(% style="background-color:#f2f2f2; width:154px" %)AT+INTMOD=?|(% style="background-color:#f2f2f2; width:196px" %)Show current interrupt mode|(% style="background-color:#f2f2f2; width:157px" %)(((
625 +(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
626 +|**Command Example**|**Function**|**Response**
627 +|AT+INTMOD=?|Show current interrupt mode|(((
647 647  0
629 +
648 648  OK
649 -the mode is 0 =Disable Interrupt
631 +
632 +the mode is 0 = No interruption
650 650  )))
651 -|(% style="background-color:#f2f2f2; width:154px" %)AT+INTMOD=2|(% style="background-color:#f2f2f2; width:196px" %)(((
634 +|AT+INTMOD=2|(((
652 652  Set Transmit Interval
653 -0. (Disable Interrupt),
654 -~1. (Trigger by rising and falling edge)
655 -2. (Trigger by falling edge)
656 -3. (Trigger by rising edge)
657 -)))|(% style="background-color:#f2f2f2; width:157px" %)OK
658 658  
659 -(% style="color:blue" %)**Downlink Command: 0x06**
637 +~1. (Disable Interrupt),
660 660  
639 +2. (Trigger by rising and falling edge),
640 +
641 +3. (Trigger by falling edge)
642 +
643 +4. (Trigger by rising edge)
644 +)))|OK
645 +
646 +**Downlink Command: 0x06**
647 +
661 661  Format: Command Code (0x06) followed by 3 bytes.
662 662  
663 663  This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
664 664  
665 -* Example 1: Downlink Payload: 06000000  ~/~/  Turn off interrupt mode
666 -* Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
652 +* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
653 +* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
667 667  
668 668  
669 669  
670 -=== 3.3.3 Set the output time ===
657 +== 3.3 Set the output time ==
671 671  
672 672  
673 673  Feature, Control the output 3V3 , 5V or 12V.
674 674  
675 -(% style="color:blue" %)**AT Command: AT+3V3T**
662 +**AT Command: AT+3V3T**
676 676  
677 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:474px" %)
678 -|=(% style="width: 154px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 201px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 116px;background-color:#D9E2F3;color:#0070C0" %)**Response**
679 -|(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=?|(% style="background-color:#f2f2f2; width:201px" %)Show 3V3 open time.|(% style="background-color:#f2f2f2; width:116px" %)(((
664 +(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
665 +|(% style="width:156px" %)**Command Example**|(% style="width:236px" %)**Function**|(% style="width:117px" %)**Response**
666 +|(% style="width:156px" %)AT+3V3T=?|(% style="width:236px" %)Show 3V3 open time.|(% style="width:117px" %)(((
680 680  0
668 +
681 681  OK
682 682  )))
683 -|(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=0|(% style="background-color:#f2f2f2; width:201px" %)Normally open 3V3 power supply.|(% style="background-color:#f2f2f2; width:116px" %)(((
671 +|(% style="width:156px" %)AT+3V3T=0|(% style="width:236px" %)Normally open 3V3 power supply.|(% style="width:117px" %)(((
684 684  OK
673 +
685 685  default setting
686 686  )))
687 -|(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=1000|(% style="background-color:#f2f2f2; width:201px" %)Close after a delay of 1000 milliseconds.|(% style="background-color:#f2f2f2; width:116px" %)(((
676 +|(% style="width:156px" %)AT+3V3T=1000|(% style="width:236px" %)Close after a delay of 1000 milliseconds.|(% style="width:117px" %)(((
688 688  OK
678 +
679 +
689 689  )))
690 -|(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=65535|(% style="background-color:#f2f2f2; width:201px" %)Normally closed 3V3 power supply.|(% style="background-color:#f2f2f2; width:116px" %)(((
681 +|(% style="width:156px" %)AT+3V3T=65535|(% style="width:236px" %)Normally closed 3V3 power supply.|(% style="width:117px" %)(((
691 691  OK
683 +
684 +
692 692  )))
693 693  
694 -(% style="color:blue" %)**AT Command: AT+5VT**
695 695  
696 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:470px" %)
697 -|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 114px;background-color:#D9E2F3;color:#0070C0" %)**Response**
698 -|(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=?|(% style="background-color:#f2f2f2; width:196px" %)Show 5V open time.|(% style="background-color:#f2f2f2; width:114px" %)(((
688 +**AT Command: AT+5VT**
689 +
690 +(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
691 +|(% style="width:158px" %)**Command Example**|(% style="width:232px" %)**Function**|(% style="width:119px" %)**Response**
692 +|(% style="width:158px" %)AT+5VT=?|(% style="width:232px" %)Show 5V open time.|(% style="width:119px" %)(((
699 699  0
694 +
700 700  OK
701 701  )))
702 -|(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=0|(% style="background-color:#f2f2f2; width:196px" %)Normally closed 5V power supply.|(% style="background-color:#f2f2f2; width:114px" %)(((
697 +|(% style="width:158px" %)AT+5VT=0|(% style="width:232px" %)Normally closed 5V power supply.|(% style="width:119px" %)(((
703 703  OK
699 +
704 704  default setting
705 705  )))
706 -|(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=1000|(% style="background-color:#f2f2f2; width:196px" %)Close after a delay of 1000 milliseconds.|(% style="background-color:#f2f2f2; width:114px" %)(((
702 +|(% style="width:158px" %)AT+5VT=1000|(% style="width:232px" %)Close after a delay of 1000 milliseconds.|(% style="width:119px" %)(((
707 707  OK
704 +
705 +
708 708  )))
709 -|(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=65535|(% style="background-color:#f2f2f2; width:196px" %)Normally open 5V power supply.|(% style="background-color:#f2f2f2; width:114px" %)(((
707 +|(% style="width:158px" %)AT+5VT=65535|(% style="width:232px" %)Normally open 5V power supply.|(% style="width:119px" %)(((
710 710  OK
709 +
710 +
711 711  )))
712 712  
713 -(% style="color:blue" %)**AT Command: AT+12VT**
714 714  
715 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:443px" %)
716 -|=(% style="width: 156px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 199px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 83px;background-color:#D9E2F3;color:#0070C0" %)**Response**
717 -|(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=?|(% style="background-color:#f2f2f2; width:199px" %)Show 12V open time.|(% style="background-color:#f2f2f2; width:83px" %)(((
714 +**AT Command: AT+12VT**
715 +
716 +(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
717 +|(% style="width:156px" %)**Command Example**|(% style="width:268px" %)**Function**|**Response**
718 +|(% style="width:156px" %)AT+12VT=?|(% style="width:268px" %)Show 12V open time.|(((
718 718  0
720 +
719 719  OK
720 720  )))
721 -|(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=0|(% style="background-color:#f2f2f2; width:199px" %)Normally closed 12V power supply.|(% style="background-color:#f2f2f2; width:83px" %)OK
722 -|(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=500|(% style="background-color:#f2f2f2; width:199px" %)Close after a delay of 500 milliseconds.|(% style="background-color:#f2f2f2; width:83px" %)(((
723 +|(% style="width:156px" %)AT+12VT=0|(% style="width:268px" %)Normally closed 12V power supply.|OK
724 +|(% style="width:156px" %)AT+12VT=500|(% style="width:268px" %)Close after a delay of 500 milliseconds.|(((
723 723  OK
726 +
727 +
724 724  )))
725 725  
726 -(% style="color:blue" %)**Downlink Command: 0x07**
727 727  
731 +**Downlink Command: 0x07**
732 +
728 728  Format: Command Code (0x07) followed by 3 bytes.
729 729  
730 730  The first byte is which power, the second and third bytes are the time to turn on.
731 731  
732 -* Example 1: Downlink Payload: 070101F4  **~-~-->**  AT+3V3T=500
733 -* Example 2: Downlink Payload: 0701FFFF   **~-~-->**  AT+3V3T=65535
734 -* Example 3: Downlink Payload: 070203E8  **~-~-->**  AT+5VT=1000
735 -* Example 4: Downlink Payload: 07020000  **~-~-->**  AT+5VT=0
736 -* Example 5: Downlink Payload: 070301F4  **~-~-->**  AT+12VT=500
737 -* Example 6: Downlink Payload: 07030000  **~-~-->**  AT+12VT=0
737 +* Example 1: Downlink Payload: 070101F4  -> AT+3V3T=500
738 +* Example 2: Downlink Payload: 0701FFFF   -> AT+3V3T=65535
739 +* Example 3: Downlink Payload: 070203E8  -> AT+5VT=1000
740 +* Example 4: Downlink Payload: 07020000  -> AT+5VT=0
741 +* Example 5: Downlink Payload: 070301F4  -> AT+12VT=500
742 +* Example 6: Downlink Payload: 07030000  -> AT+12VT=0
738 738  
739 739  
740 740  
741 -=== 3.3.4 Set the Probe Model ===
746 +== 3.4 Set the Probe Model ==
742 742  
743 743  
744 -Users need to configure this parameter according to the type of external probe. In this way, the server can decode according to this value, and convert the current value output by the sensor into water depth or pressure value.
749 +**AT Command: AT** **+PROBE**
745 745  
746 -(% style="color:blue" %)**AT Command: AT** **+PROBE**
751 +(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
752 +|(% style="width:157px" %)**Command Example**|(% style="width:267px" %)**Function**|**Response**
753 +|(% style="width:157px" %)AT +PROBE =?|(% style="width:267px" %)Get or Set the probe model.|(((
754 +0
747 747  
748 -AT+PROBE=aabb
756 +OK
757 +)))
758 +|(% style="width:157px" %)AT +PROBE =0003|(% style="width:267px" %)Set water depth sensor mode, 3m type.|OK
759 +|(% style="width:157px" %)AT +PROBE =0101|(% style="width:267px" %)Set pressure transmitters mode, first type.|(((
760 +OK
749 749  
750 -When aa=00, it is the water depth mode, and the current is converted into the water depth value; bb is the probe at a depth of several meters.
762 +
763 +)))
764 +|(% style="width:157px" %)AT +PROBE =0000|(% style="width:267px" %)Initial state, no settings.|(((
765 +OK
751 751  
752 -When aa=01, it is the pressure mode, which converts the current into a pressure value;
767 +
768 +)))
753 753  
754 -bb represents which type of pressure sensor it is.
770 +**Downlink Command: 0x08**
755 755  
756 -(A->01,B->02,C->03,D->04,E->05,F->06,G->07,H->08,I->09,J->0A,K->0B,L->0C)
772 +Format: Command Code (0x08) followed by 2 bytes.
757 757  
758 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
759 -|(% style="background-color:#d9e2f3; color:#0070c0; width:154px" %)**Command Example**|(% style="background-color:#d9e2f3; color:#0070c0; width:269px" %)**Function**|(% style="background-color:#d9e2f3; color:#0070c0" %)**Response**
760 -|(% style="background-color:#f2f2f2; width:154px" %)AT +PROBE =?|(% style="background-color:#f2f2f2; width:269px" %)Get or Set the probe model.|(% style="background-color:#f2f2f2" %)0
761 -OK
762 -|(% style="background-color:#f2f2f2; width:154px" %)AT +PROBE =0003|(% style="background-color:#f2f2f2; width:269px" %)Set water depth sensor mode, 3m type.|(% style="background-color:#f2f2f2" %)OK
763 -|(% style="background-color:#f2f2f2; width:154px" %)(((
764 -AT +PROBE =000A
774 +* Example 1: Downlink Payload: 080003  -> AT+PROBE=0003
775 +* Example 2: Downlink Payload: 080101  -> AT+PROBE=0101
765 765  
766 -
767 -)))|(% style="background-color:#f2f2f2; width:269px" %)Set water depth sensor mode, 10m type.|(% style="background-color:#f2f2f2" %)OK
768 -|(% style="background-color:#f2f2f2; width:154px" %)AT +PROBE =0101|(% style="background-color:#f2f2f2; width:269px" %)Set pressure transmitters mode, first type(A).|(% style="background-color:#f2f2f2" %)OK
769 -|(% style="background-color:#f2f2f2; width:154px" %)AT +PROBE =0000|(% style="background-color:#f2f2f2; width:269px" %)Initial state, no settings.|(% style="background-color:#f2f2f2" %)OK
770 770  
771 -(% style="color:blue" %)**Downlink Command: 0x08**
772 772  
773 -Format: Command Code (0x08) followed by 2 bytes.
779 += 4. Battery & how to replace =
774 774  
775 -* Example 1: Downlink Payload: 080003  **~-~-->**  AT+PROBE=0003
776 -* Example 2: Downlink Payload: 080101  **~-~-->**  AT+PROBE=0101
781 +== 4.1 Battery Type ==
777 777  
778 778  
784 +PS-LB is equipped with a [[8500mAH ER26500 Li-SOCI2 battery>>https://www.dropbox.com/sh/w9l2oa3ytpculph/AAAPtt-apH4lYfCj-2Y6lHvQa?dl=0]]. The battery is un-rechargeable battery with low discharge rate targeting for 8~~10 years use. This type of battery is commonly used in IoT target for long-term running, such as water meter.
779 779  
780 -=== 3.3.5 Multiple collections are one uplink（Since firmware V1.1） ===
781 781  
787 +The discharge curve is not linear so can’t simply use percentage to show the battery level. Below is the battery performance.
782 782  
783 -Added AT+STDC command to collect the voltage of VDC_INPUT multiple times and upload it at one time.
789 +[[image:1675146710956-626.png]]
784 784  
785 -(% style="color:blue" %)**AT Command: AT** **+STDC**
786 786  
787 -AT+STDC=aa,bb,bb
792 +Minimum Working Voltage for the PS-LB:
788 788  
789 -(% style="color:#037691" %)**aa:**(%%)
790 -**0:** means disable this function and use TDC to send packets.
791 -**1:** means enable this function, use the method of multiple acquisitions to send packets.
792 -(% style="color:#037691" %)**bb:**(%%) Each collection interval (s), the value is 1~~65535
793 -(% style="color:#037691" %)**cc:**(%%)** **the number of collection times, the value is 1~~120
794 +PS-LB:  2.45v ~~ 3.6v
794 794  
795 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
796 -|(% style="background-color:#d9e2f3; color:#0070c0; width:160px" %)**Command Example**|(% style="background-color:#d9e2f3; color:#0070c0; width:215px" %)**Function**|(% style="background-color:#d9e2f3; color:#0070c0" %)**Response**
797 -|(% style="background-color:#f2f2f2; width:160px" %)AT+STDC=?|(% style="background-color:#f2f2f2; width:215px" %)Get the mode of multiple acquisitions and one uplink.|(% style="background-color:#f2f2f2" %)1,10,18
798 -OK
799 -|(% style="background-color:#f2f2f2; width:160px" %)AT+STDC=1,10,18|(% style="background-color:#f2f2f2; width:215px" %)Set the mode of multiple acquisitions and one uplink, collect once every 10 seconds, and report after 18 times.|(% style="background-color:#f2f2f2" %)(((
800 -Attention:Take effect after ATZ
801 801  
802 -OK
803 -)))
804 -|(% style="background-color:#f2f2f2; width:160px" %)AT+STDC=0, 0,0|(% style="background-color:#f2f2f2; width:215px" %)(((
805 -Use the TDC interval to send packets.(default)
797 +== 4.2 Replace Battery ==
806 806  
807 -
808 -)))|(% style="background-color:#f2f2f2" %)(((
809 -Attention:Take effect after ATZ
810 810  
811 -OK
812 -)))
800 +Any battery with range 2.45 ~~ 3.6v can be a replacement. We recommend to use Li-SOCl2 Battery.
813 813  
814 -(% style="color:blue" %)**Downlink Command: 0xAE**
802 +And make sure the positive and negative pins match.
815 815  
816 -Format: Command Code (0x08) followed by 5 bytes.
817 817  
818 -* Example 1: Downlink Payload: AE 01 02 58 12** ~-~-->**  AT+STDC=1,600,18
805 +== 4.3 Power Consumption Analyze ==
819 819  
820 820  
808 +Dragino Battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
821 821  
822 -= 4. Battery & Power Consumption =
823 823  
811 +Instruction to use as below:
824 824  
825 -PS-LB-NA uses ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
826 826  
827 -[[**Battery Info & Power Consumption Analyze**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
814 +**Step 1:** Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from:
828 828  
816 +[[https:~~/~~/www.dropbox.com/sh/zwex6i331j5oeq2/AACIMf9f_v2qsJ39CuMQ5Py_a?dl=0>>https://www.dropbox.com/sh/zwex6i331j5oeq2/AACIMf9f_v2qsJ39CuMQ5Py_a?dl=0]]
829 829  
830 -= 5. OTA firmware update =
831 831  
819 +**Step 2:** Open it and choose
832 832  
821 +* Product Model
822 +* Uplink Interval
823 +* Working Mode
824 +
825 +And the Life expectation in difference case will be shown on the right.
826 +
827 +[[image:1675146895108-304.png]]
828 +
829 +
830 +The battery related documents as below:
831 +
832 +* [[Battery Dimension>>https://www.dropbox.com/s/ox5g9njwjle7aw3/LSN50-Battery-Dimension.pdf?dl=0]],
833 +* [[Lithium-Thionyl Chloride Battery datasheet, Tech Spec>>https://www.dropbox.com/sh/d4oyfnp8o94180o/AABQewCNSh5GPeQH86UxRgQQa?dl=0]]
834 +* [[Lithium-ion Battery-Capacitor datasheet>>https://www.dropbox.com/s/791gjes2lcbfi1p/SPC_1520_datasheet.jpg?dl=0]], [[Tech Spec>>https://www.dropbox.com/s/4pkepr9qqqvtzf2/SPC1520%20Technical%20Specification20171123.pdf?dl=0]]
835 +
836 +[[image:image-20230131145708-3.png]]
837 +
838 +
839 +=== 4.3.1 ​Battery Note ===
840 +
841 +
842 +The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
843 +
844 +
845 +=== 4.3.2 Replace the battery ===
846 +
847 +
848 +You can change the battery in the PS-LB.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won't be voltage drop between battery and main board.
849 +
850 +The default battery pack of PS-LB includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
851 +
852 +
853 += 5. Remote Configure device =
854 +
855 +== 5.1 Connect via BLE ==
856 +
857 +
858 +Please see this instruction for how to configure via BLE: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]]
859 +
860 +
861 +== 5.2 AT Command Set ==
862 +
863 +
864 +
865 += 6. OTA firmware update =
866 +
867 +
833 833  Please see this link for how to do OTA firmware update: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
834 834  
835 835  
836 -= 6. FAQ =
871 += 7. FAQ =
837 837  
838 -== 6.1 How to use AT Command via UART to access device? ==
873 +== 7.1 How to use AT Command to access device? ==
839 839  
840 840  
841 841  See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
842 842  
843 843  
844 -== 6.2 How to update firmware via UART port? ==
879 +== 7.2 How to update firmware via UART port? ==
845 845  
846 846  
847 847  See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
848 848  
849 849  
850 -== 6.3 How to change the LoRa Frequency Bands/Region? ==
885 +== 7.3 How to change the LoRa Frequency Bands/Region? ==
851 851  
852 852  
853 853  You can follow the instructions for [[how to upgrade image>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]].
... ... @@ -854,20 +854,20 @@
854 854  When downloading the images, choose the required image file for download. ​
855 855  
856 856  
857 -= 7. Order Info =
892 += 8. Order Info =
858 858  
859 859  
860 860  [[image:image-20230131153105-4.png]]
861 861  
862 862  
863 -= 8. ​Packing Info =
898 += 9. ​Packing Info =
864 864  
865 865  
866 -(% style="color:#037691" %)**Package Includes**:
901 +**Package Includes**:
867 867  
868 868  * PS-LB LoRaWAN Pressure Sensor
869 869  
870 -(% style="color:#037691" %)**Dimension and weight**:
905 +**Dimension and weight**:
871 871  
872 872  * Device Size: cm
873 873  * Device Weight: g
... ... @@ -876,11 +876,10 @@
876 876  
877 877  
878 878  
879 -= 9. Support =
914 += 10. Support =
880 880  
881 881  
882 882  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
883 -
884 884  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
885 885  
886 886  
image-20230201090514-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -560.9 KB
Content
image-20230220171300-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -98.0 KB
Content
image-20230222174559-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Bei
Size
... ... @@ -1,1 +1,0 @@
1 -19.4 KB
Content
image-20230225154759-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Edwin
Size
... ... @@ -1,1 +1,0 @@
1 -468.9 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0