Skip to Content
Version 123.3 by Xiaoling on 2025/04/01 16:46
Show last authors
1
2
3
4 (% style="text-align:center" %)
5 [[image:image-20240109154731-4.png||height="671" width="945"]]
6
7
8
9
10
11
12
13 **Table of Contents :**
14
15 {{toc/}}
16
17
18
19
20
21
22 = 1. Introduction =
23
24 == 1.1 What is LoRaWAN Pressure Sensor ==
25
26
27 (((
28 The Dragino PS-LB/LS series sensors are (% style="color:blue" %)**LoRaWAN Pressure Sensor**(%%) for Internet of Things solution. PS-LB/LS can measure Air, Water pressure and liquid level and upload the sensor data via wireless to LoRaWAN IoT server.
29 )))
30
31 (((
32 The PS-LB/LS series sensors include (% style="color:blue" %)**Thread Installation Type**(%%) and (% style="color:blue" %)**Immersion Type**(%%), it supports different pressure range which can be used for different measurement requirement.
33 )))
34
35 (((
36 The LoRa wireless technology used in PS-LB/LS allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
37 )))
38
39 (((
40 PS-LB/LS supports BLE configure and wireless OTA update which make user easy to use.
41 )))
42
43 (((
44 PS-LB/LS is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery **(%%)or (% style="color:blue" %)**solar powered + Li-ion battery **(%%), it is designed for long term use up to 5 years.
45 )))
46
47 (((
48 Each PS-LB/LS is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
49 )))
50
51 [[image:1675071321348-194.png]]
52
53
54 == 1.2 ​Features ==
55
56
57 * LoRaWAN 1.0.3 Class A
58 * Ultra-low power consumption
59 * Measure air / gas or water pressure
60 * Different pressure range available
61 * Thread Installation Type or Immersion Type
62 * Monitor Battery Level
63 * Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
64 * Support Bluetooth v5.1 and LoRaWAN remote configure
65 * Support wireless OTA update firmware
66 * Uplink on periodically
67 * Downlink to change configure
68 * Controllable 3.3v,5v and 12v output to power external sensor
69 * 8500mAh Li/SOCl2 Battery (PS-LB)
70 * Solar panel + 3000mAh Li-ion battery (PS-LS)
71
72 == 1.3 Specification ==
73
74
75 (% style="color:#037691" %)**Micro Controller:**
76
77 * MCU: 48Mhz ARM
78 * Flash: 256KB
79 * RAM: 64KB
80
81 (% style="color:#037691" %)**Common DC Characteristics:**
82
83 * Supply Voltage: Built-in Battery , 2.5v ~~ 3.6v
84 * Operating Temperature: -40 ~~ 85°C
85
86 (% style="color:#037691" %)**LoRa Spec:**
87
88 * Frequency Range,  Band 1 (HF): 862 ~~ 1020 Mhz,Band 2 (LF): 410 ~~ 528 Mhz
89 * Max +22 dBm constant RF output vs.
90 * RX sensitivity: down to -139 dBm.
91 * Excellent blocking immunity
92
93 (% style="color:#037691" %)**Current Input Measuring :**
94
95 * Range: 0 ~~ 20mA
96 * Accuracy: 0.02mA
97 * Resolution: 0.001mA
98
99 (% style="color:#037691" %)**Voltage Input Measuring:**
100
101 * Range: 0 ~~ 30v
102 * Accuracy: 0.02v
103 * Resolution: 0.001v
104
105 (% style="color:#037691" %)**Battery:**
106
107 * Li/SOCI2 un-chargeable battery
108 * Capacity: 8500mAh
109 * Self-Discharge: <1% / Year @ 25°C
110 * Max continuously current: 130mA
111 * Max boost current: 2A, 1 second
112
113 (% style="color:#037691" %)**Power Consumption**
114
115 * Sleep Mode: 5uA @ 3.3v
116 * LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
117
118 == 1.4 Probe Types ==
119
120 === 1.4.1 Thread Installation Type ===
121
122
123 [[image:1675071448299-229.png]]
124
125 * Hersman Pressure Transmitter
126 * Measuring Range: -0.1 ~~ 0 ~~ 60MPa, see order info.
127 * Accuracy: 0.2% F.S
128 * Long-Term Stability: 0.2% F.S ±0.05%
129 * Overload 200% F.S
130 * Zero Temperature Drift: 0.03% FS/℃(≤100Kpa), 0.02%FS/℃(＞100Kpa)
131 * FS Temperature Drift: 0.003% FS/℃(≤100Kpa), 0.002%FS/℃(＞100Kpa)
132 * Storage temperature: -30℃~~80℃
133 * Operating temperature: -20℃~~60℃
134 * Connector Type: Various Types, see order info
135
136 === 1.4.2 Immersion Type ===
137
138
139 [[image:image-20240109160445-5.png||height="221" width="166"]]
140
141 * Immersion Type, Probe IP Level: IP68
142 * Measuring Range: Measure range can be customized, up to 100m.
143 * Accuracy: 0.2% F.S
144 * Long-Term Stability: ±0.2% F.S / Year
145 * Storage temperature: -30°C~~80°C
146 * Operating temperature: 0°C~~50°C
147 * Material: 316 stainless steels
148
149 === 1.4.3 Wireless Differential Air Pressure Sensor ===
150
151 [[image:image-20240511174954-1.png||height="215" width="215"]]
152
153 * Measuring Range: -100KPa~~0~~100KPa(Optional measuring range).
154 * Accuracy: 0.5% F.S, resolution is 0.05%.
155 * Overload: 300% F.S
156 * Zero temperature drift: ±0.03%F.S/°C
157 * Operating temperature: -20°C~~60°C
158 * Storage temperature:  -20°C~~60°C
159 * Compensation temperature: 0~~50°C
160
161 == 1.5 Application and Installation ==
162
163 === 1.5.1 Thread Installation Type ===
164
165
166 Application:
167
168 * Hydraulic Pressure
169 * Petrochemical Industry
170 * Health and Medical
171 * Food & Beverage Processing
172 * Auto-controlling house
173 * Constant Pressure Water Supply
174 * Liquid Pressure measuring
175
176 Order the suitable thread size and install to measure the air / liquid pressure
177
178 [[image:1675071670469-145.png]]
179
180
181 === 1.5.2 Immersion Type ===
182
183
184 Application:
185
186 Liquid & Water Pressure / Level detect.
187
188 [[image:1675071725288-579.png]]
189
190
191 Below is the wiring to for connect the probe to the device.
192
193 The Immersion Type Sensor has different variant which defined by Ixx. For example, this means two points:
194
195 * Cable Length: 10 Meters
196 * Water Detect Range: 0 ~~ 10 Meters.
197
198 [[image:1675071736646-450.png]]
199
200
201 [[image:1675071776102-240.png]]
202
203 Size of immersion type water depth sensor:
204
205 [[image:image-20250401102131-1.png||height="268" width="707"]]
206
207
208 === 1.5.3 Wireless Differential Air Pressure Sensor ===
209
210
211 Application:
212
213 Indoor Air Control & Filter clogging Detect.
214
215 [[image:image-20240513100129-6.png]]
216
217 [[image:image-20240513100135-7.png]]
218
219
220 Below is the wiring to for connect the probe to the device.
221
222 [[image:image-20240513093957-1.png]]
223
224
225 Size of wind pressure transmitter:
226
227 [[image:image-20240513094047-2.png]]
228
229 Note: The above dimensions are measured by hand, and the numerical error of the shell is within ±0.2mm.
230
231
232 == 1.6 Sleep mode and working mode ==
233
234
235 Deep Sleep Mode: Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
236
237 Working Mode: In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
238
239
240 == 1.7 Button & LEDs ==
241
242
243 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/RS485-LB_Waterproof_RS485UART_to_LoRaWAN_Converter/WebHome/image-20240103160425-4.png?rev=1.1||alt="image-20240103160425-4.png"]]
244
245 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
246 |=(% style="width: 167px;background-color:#4F81BD;color:white" %)Behavior on ACT|=(% style="width: 117px;background-color:#4F81BD;color:white" %)Function|=(% style="width: 226px;background-color:#4F81BD;color:white" %)Action
247 |(% style="background-color:#f2f2f2; width:167px" %)Pressing ACT between 1s < time < 3s|(% style="background-color:#f2f2f2; width:117px" %)Send an uplink|(% style="background-color:#f2f2f2; width:225px" %)(((
248
249
250 If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, blue led will blink once.
251 Meanwhile, BLE module will be active and user can connect via BLE to configure device.
252 )))
253 |(% style="background-color:#f2f2f2; width:167px" %)Pressing ACT for more than 3s|(% style="background-color:#f2f2f2; width:117px" %)Active Device|(% style="background-color:#f2f2f2; width:225px" %)(((
254
255
256 Green led will fast blink 5 times, device will enter OTA mode for 3 seconds. And then start to JOIN LoRaWAN network.
257 Green led will solidly turn on for 5 seconds after joined in network.
258 Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
259 )))
260 |(% style="background-color:#f2f2f2; width:167px" %)Fast press ACT 5 times.|(% style="background-color:#f2f2f2; width:117px" %)Deactivate Device|(% style="background-color:#f2f2f2; width:225px" %)Red led will solid on for 5 seconds. Means PS-LB is in Deep Sleep Mode.
261
262 == 1.8 Pin Mapping ==
263
264
265 [[image:1675072568006-274.png]]
266
267
268 == 1.9 BLE connection ==
269
270
271 PS-LB/LS support BLE remote configure.
272
273
274 BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
275
276 * Press button to send an uplink
277 * Press button to active device.
278 * Device Power on or reset.
279
280 If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
281
282
283 == 1.10 Mechanical ==
284
285 === 1.10.1 for LB version ===
286
287
288 [[image:image-20250401163530-1.jpeg]]
289
290
291 === 1.10.2 for LS version ===
292
293
294 [[image:image-20250401163539-2.jpeg]]
295
296
297 = 2. Configure PS-LB/LS to connect to LoRaWAN network =
298
299 == 2.1 How it works ==
300
301
302 The PS-LB/LS is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and activate the PS-LB/LS. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
303
304
305 == 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
306
307
308 Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
309
310 [[image:1675144005218-297.png]]
311
312
313 The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
314
315
316 Step 1: Create a device in TTN with the OTAA keys from PS-LB/LS.
317
318 Each PS-LB/LS is shipped with a sticker with the default device EUI as below:
319
320 [[image:image-20230426085320-1.png||height="234" width="504"]]
321
322
323 You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
324
325
326 Register the device
327
328 [[image:1675144099263-405.png]]
329
330
331 Add APP EUI and DEV EUI
332
333 [[image:1675144117571-832.png]]
334
335
336 Add APP EUI in the application
337
338
339 [[image:1675144143021-195.png]]
340
341
342 Add APP KEY
343
344 [[image:1675144157838-392.png]]
345
346 Step 2: Activate on PS-LB/LS
347
348
349 Press the button for 5 seconds to activate the PS-LB/LS.
350
351 Green led will fast blink 5 times, device will enter OTA mode for 3 seconds. And then start to JOIN LoRaWAN network. Green led will solidly turn on for 5 seconds after joined in network.
352
353 After join success, it will start to upload messages to TTN and you can see the messages in the panel.
354
355
356 == 2.3 ​Uplink Payload ==
357
358 === 2.3.1 Device Status, FPORT~=5 ===
359
360
361 Include device configure status. Once PS-LB/LS Joined the network, it will uplink this message to the server.
362
363 Users can also use the downlink command(0x26 01) to ask PS-LB/LS to resend this uplink.
364
365 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
366 |(% colspan="6" style="background-color:#4f81bd; color:white" %)Device Status (FPORT=5)
367 |(% style="background-color:#f2f2f2; width:103px" %)Size (bytes)|(% style="background-color:#f2f2f2; width:72px" %)1|(% style="background-color:#f2f2f2" %)2|(% style="background-color:#f2f2f2; width:91px" %)1|(% style="background-color:#f2f2f2; width:86px" %)1|(% style="background-color:#f2f2f2; width:44px" %)2
368 |(% style="background-color:#f2f2f2; width:103px" %)Value|(% style="background-color:#f2f2f2; width:72px" %)Sensor Model|(% style="background-color:#f2f2f2" %)Firmware Version|(% style="background-color:#f2f2f2; width:91px" %)Frequency Band|(% style="background-color:#f2f2f2; width:86px" %)Sub-band|(% style="background-color:#f2f2f2; width:44px" %)BAT
369
370 Example parse in TTNv3
371
372 [[image:1675144504430-490.png]]
373
374
375 Sensor Model: For PS-LB/LS, this value is 0x16
376
377 Firmware Version: 0x0100, Means: v1.0.0 version
378
379 Frequency Band:
380
381 *0x01: EU868
382
383 *0x02: US915
384
385 *0x03: IN865
386
387 *0x04: AU915
388
389 *0x05: KZ865
390
391 *0x06: RU864
392
393 *0x07: AS923
394
395 *0x08: AS923-1
396
397 *0x09: AS923-2
398
399 *0x0a: AS923-3
400
401 *0x0b: CN470
402
403 *0x0c: EU433
404
405 *0x0d: KR920
406
407 *0x0e: MA869
408
409
410 Sub-Band:
411
412 AU915 and US915:value 0x00 ~~ 0x08
413
414 CN470: value 0x0B ~~ 0x0C
415
416 Other Bands: Always 0x00
417
418
419 Battery Info:
420
421 Check the battery voltage.
422
423 Ex1: 0x0B45 = 2885mV
424
425 Ex2: 0x0B49 = 2889mV
426
427
428 === 2.3.2 Sensor value, FPORT~=2 ===
429
430
431 Uplink payload includes in total 9 bytes.
432
433
434 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
435 |(% style="background-color:#4f81bd; color:white; width:97px" %)(((
436
437
438 Size(bytes)
439 )))|(% style="background-color:#4f81bd; color:white; width:50px" %)2|(% style="background-color:#4f81bd; color:white; width:71px" %)2|(% style="background-color:#4f81bd; color:white; width:98px" %)2|(% style="background-color:#4f81bd; color:white; width:73px" %)2|(% style="background-color:#4f81bd; color:white; width:122px" %)1
440 |(% style="width:97px" %)Value|(% style="width:48px" %)[[BAT>>||anchor="H2.3.3BatteryInfo"]]|(% style="width:71px" %)[[Probe Model>>||anchor="H2.3.4ProbeModel"]]|(% style="width:98px" %)[[0 ~~~~ 20mA value>>||anchor="H2.3.507E20mAvalue28IDC_IN29"]]|(% style="width:73px" %)[[0 ~~~~ 30v value>>||anchor="H2.3.607E30Vvalue28pinVDC_IN29"]]|(% style="width:122px" %)[[IN1 &IN2 Interrupt  flag>>||anchor="H2.3.7IN126IN226INTpin"]]
441
442 [[image:1675144608950-310.png]]
443
444
445 === 2.3.3 Battery Info ===
446
447
448 Check the battery voltage for PS-LB/LS.
449
450 Ex1: 0x0B45 = 2885mV
451
452 Ex2: 0x0B49 = 2889mV
453
454
455 === 2.3.4 Probe Model ===
456
457
458 PS-LB/LS has different kind of probe, 4~~20mA represent the full scale of the measuring range. So a 12mA output means different meaning for different probe. 
459
460
461 For example.
462
463 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
464 |(% style="background-color:#4f81bd; color:white" %)Part Number|(% style="background-color:#4f81bd; color:white" %)Probe Used|(% style="background-color:#4f81bd; color:white" %)4~~20mA scale|(% style="background-color:#4f81bd; color:white" %)Example: 12mA meaning
465 |(% style="background-color:#f2f2f2" %)PS-LB/LS-I3|(% style="background-color:#f2f2f2" %)immersion type with 3 meters cable|(% style="background-color:#f2f2f2" %)0~~3 meters|(% style="background-color:#f2f2f2" %)1.5 meters pure water
466 |(% style="background-color:#f2f2f2" %)PS-LB/LS-I5|(% style="background-color:#f2f2f2" %)immersion type with 5 meters cable|(% style="background-color:#f2f2f2" %)0~~5 meters|(% style="background-color:#f2f2f2" %)2.5 meters pure water
467 |(% style="background-color:#f2f2f2" %)PS-LB/LS-T20-B|(% style="background-color:#f2f2f2" %)T20 threaded probe|(% style="background-color:#f2f2f2" %)0~~1MPa|(% style="background-color:#f2f2f2" %)0.5MPa air / gas or water pressure
468
469 The probe model field provides the convenient for server to identical how it should parse the 4~~20mA sensor value and get the correct value.
470
471
472 === 2.3.5 0~~20mA value (IDC_IN) ===
473
474
475 The output value from Pressure Probe, use together with Probe Model to get the pressure value or water level.
476
477 Example:
478
479 27AE(H) = 10158 (D)/1000 = 10.158mA.
480
481
482 Instead of pressure probe, User can also connect a general 4~~20mA in this port to support different types of 4~~20mA sensors. below is the connection example:
483
484 [[image:image-20230225154759-1.png||height="408" width="741"]]
485
486
487 === 2.3.6 0~~30V value (pin VDC_IN) ===
488
489
490 Measure the voltage value. The range is 0 to 30V.
491
492 Example:
493
494 138E(H) = 5006(D)/1000= 5.006V
495
496
497 === 2.3.7 IN1&IN2&INT pin ===
498
499
500 IN1 and IN2 are used as digital input pins.
501
502 Example:
503
504 09 (H): (0x09&0x08)>>3=1    IN1 pin is high level.
505
506 09 (H): (0x09&0x04)>>2=0    IN2 pin is low level.
507
508
509 This data field shows if this packet is generated by Interrupt Pin or not. [[Click here>>||anchor="H3.3.2SetInterruptMode"]] for the hardware and software set up. Note: The Internet Pin is a separate pin in the screw terminal.
510
511 Example:
512
513 09 (H): (0x09&0x02)>>1=1    The level of the interrupt pin.
514
515 09 (H): 0x09&0x01=1              0x00: Normal uplink packet.
516
517 0x01: Interrupt Uplink Packet.
518
519
520 === 2.3.8 Sensor value, FPORT~=7 ===
521
522
523 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:500px" %)
524 |(% style="background-color:#4f81bd; color:white; width:65px" %)(((
525
526
527 Size(bytes)
528 )))|(% style="background-color:#4f81bd; color:white; width:35px" %)2|(% style="background-color:#4f81bd; color:white; width:400px" %)n
529 |(% style="width:94px" %)Value|(% style="width:43px" %)[[BAT>>||anchor="H2.3.3BatteryInfo"]]|(% style="width:367px" %)(((
530
531
532 Voltage value, each 2 bytes is a set of voltage values.
533 )))
534
535 [[image:image-20230220171300-1.png||height="207" width="863"]]
536
537 Multiple sets of data collected are displayed in this form：
538
539 [voltage value1], [voltage value2], [voltage value3],…[voltage value n/2]
540
541
542 === 2.3.9 ​Decode payload in The Things Network ===
543
544
545 While using TTN network, you can add the payload format to decode the payload.
546
547 [[image:1675144839454-913.png]]
548
549
550 PS-LB/LS TTN Payload Decoder: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]
551
552
553 == 2.4 Uplink Interval ==
554
555
556 The PS-LB/LS by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H4.1ChangeUplinkInterval>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H4.1ChangeUplinkInterval||style="background-color: rgb(255, 255, 255);"]]
557
558
559 == 2.5 Show Data in DataCake IoT Server ==
560
561
562 [[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
563
564 Step 1: Be sure that your device is programmed and properly connected to the network at this time.
565
566 Step 2: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
567
568 [[image:1675144951092-237.png]]
569
570
571 [[image:1675144960452-126.png]]
572
573
574 Step 3: Create an account or log in Datacake.
575
576 Step 4: Create PS-LB/LS product.
577
578 [[image:1675145004465-869.png]]
579
580
581 [[image:1675145018212-853.png]]
582
583
584 [[image:1675145029119-717.png]]
585
586
587 Step 5: add payload decode
588
589 [[image:1675145051360-659.png]]
590
591
592 [[image:1675145060812-420.png]]
593
594
595 After added, the sensor data arrive TTN, it will also arrive and show in Datacake.
596
597 [[image:1675145081239-376.png]]
598
599
600 == 2.6 Datalog Feature (Since V1.1) ==
601
602
603 When a user wants to retrieve sensor value, he can send a poll command from the IoT platform to ask the sensor to send value in the required time slot.
604
605
606 === 2.6.1 Unix TimeStamp ===
607
608
609 PS-LB uses Unix TimeStamp format based on
610
611 [[image:image-20250401163826-3.jpeg]]
612
613 Users can get this time from the link:  [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
614
615 Below is the converter example:
616
617 [[image:image-20250401163906-4.jpeg]]
618
619
620 === 2.6.2 Set Device Time ===
621
622
623 There are two ways to set the device's time:
624
625
626 ~1. Through LoRaWAN MAC Command (Default settings)
627
628 Users need to set SYNCMOD=1 to enable sync time via the MAC command.
629
630 Once CPL01 Joined the LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to CPL01. If CPL01 fails to get the time from the server, CPL01 will use the internal time and wait for the next time request ~[[[via Device Status (FPORT=5)>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/#H2.3.1DeviceStatus2CFPORT3D5]]].
631
632 Note: LoRaWAN Server needs to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature.
633
634
635 2. Manually Set Time
636
637 Users need to set SYNCMOD=0 to manual time, otherwise, the user set time will be overwritten by the time set by the server.
638
639
640 === 2.6.3 Poll sensor value ===
641
642 Users can poll sensor values based on timestamps. Below is the downlink command.
643
644 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:470px" %)
645 |=(% colspan="4" style="width: 160px; background-color:#4F81BD;color:white" %)Downlink Command to poll Open/Close status (0x31)
646 |(% style="background-color:#f2f2f2; width:67px" %)1byte|(% style="background-color:#f2f2f2; width:145px" %)4bytes|(% style="background-color:#f2f2f2; width:133px" %)4bytes|(% style="background-color:#f2f2f2; width:163px" %)1byte
647 |(% style="background-color:#f2f2f2; width:67px" %)31|(% style="background-color:#f2f2f2; width:145px" %)Timestamp start|(% style="background-color:#f2f2f2; width:133px" %)(((
648
649
650 Timestamp end
651 )))|(% style="background-color:#f2f2f2; width:163px" %)Uplink Interval
652
653 Timestamp start and Timestamp end-use Unix TimeStamp format as mentioned above. Devices will reply with all data logs during this period, using the uplink interval.
654
655 For example, downlink command[[image:image-20250117104812-1.png]]
656
657 Is to check 2024/12/20 09:34:59 to 2024/12/20 14:34:59's data
658
659 Uplink Internal =5s，means PS-LB will send one packet every 5s. range 5~~255s.
660
661
662 === 2.6.4 Datalog Uplink payload (FPORT~=3) ===
663
664
665 The Datalog uplinks will use below payload format.
666
667 Retrieval data payload:
668
669 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
670 |=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
671 Size(bytes)
672 )))|=(% style="width: 70px; background-color:#4F81BD;color:white" %)2|=(% style="width: 70px; background-color:#4F81BD;color:white" %)2|=(% style="width: 80px; background-color: rgb(79, 129, 189); color: white;" %)2|=(% style="width: 150px; background-color: rgb(79, 129, 189); color: white;" %)1|=(% style="width: 80px; background-color: rgb(79, 129, 189); color: white;" %)4
673 |(% style="width:103px" %)Value|(% style="width:68px" %)(((
674 Probe_mod
675 )))|(% style="width:104px" %)(((
676 VDC_intput_V
677 )))|(% style="width:83px" %)(((
678 IDC_intput_mA
679 )))|(% style="width:201px" %)(((
680 IN1_pin_level& IN2_pin_level& Exti_pin_level&Exti_status
681 )))|(% style="width:86px" %)Unix Time Stamp
682 IN1_pin_level & IN2_pin_level & Exti_pin_level & Exti_status:
683
684 [[image:image-20250117104847-4.png]]
685
686
687 No ACK Message:  1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for PNACKMD=1 feature)
688
689 Poll Message Flag: 1: This message is a poll message reply.
690
691 * Poll Message Flag is set to 1.
692
693 * Each data entry is 11 bytes, to save airtime and battery, devices will send max bytes according to the current DR and Frequency bands.
694
695 For example, in US915 band, the max payload for different DR is:
696
697 a) DR0: max is 11 bytes so one entry of data
698
699 b) DR1: max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
700
701 c) DR2: total payload includes 11 entries of data
702
703 d) DR3: total payload includes 22 entries of data.
704
705 If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0   
706
707 Example:
708
709 If PS-LB-NA has below data inside Flash:
710
711 [[image:image-20250117104837-3.png]]
712
713
714 If user sends below downlink command: 316788D9BF6788DB6305
715
716 Where : Start time: 6788D9BF = time 25/1/16 10:04:47
717
718 Stop time: 6788DB63 = time 25/1/16 10:11:47
719
720
721 PA-LB-NA will uplink this payload.
722
723 [[image:image-20250117104827-2.png]]
724
725
726 00001B620000406788D9BF  00000D130000406788D9FB  00000D120000406788DA37  00000D110000406788DA73  00000D100000406788DAAF  00000D100000406788DAEB  00000D0F0000406788DB27  00000D100000406788DB63
727
728
729 Where the first 11 bytes is for the first entry :
730
731
732 0000  0D10  0000  40  6788DB63
733
734
735 Probe_mod = 0x0000 = 0000
736
737
738 VDC_intput_V = 0x0D10/1000=3.344V
739
740 IDC_intput_mA = 0x0000/1000=0mA
741
742
743 IN1_pin_level = (0x40& 0x08)? "High":"Low" = 0(Low)
744
745 IN2_pin_level = (0x40& 0x04)? "High":"Low" = 0(Low)
746
747 Exti_pin_level = (0x40& 0x02)? "High":"Low" = 0(Low)
748
749 Exti_status = (0x40& 0x01)? "True":"False" = 0(False)
750
751
752 Unix time is 0x6788DB63 = 1737022307s = 2025/1/16 10:11:47
753
754 Its data format is:
755
756 [Probe_mod, VDC_intput_V, IDC_intput_mA, IN1_pin_level, IN2_pin_level, Exti_pin_level, water_deep, Data_time],[Probe_mod, VDC_intput_V, IDC_intput_mA, IN1_pin_level, IN2_pin_level, Exti_pin_level, water_deep, Data_time],...
757
758 Note: water_deep in the data needs to be converted using decoding to get it.
759
760
761 === 2.6.5 Decoder in TTN V3 ===
762
763 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/1652862574387-195.png?width=722&height=359&rev=1.1||alt="1652862574387-195.png" height="359" width="722"]]
764
765 Please check the decoder from this link: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]
766
767
768 == 2.7 Frequency Plans ==
769
770
771 The PS-LB/LS uses OTAA mode and below frequency plans by default. Each frequency band use different firmware, user update the firmware to the corresponding band for their country.
772
773 [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/a>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
774
775
776 == 2.8 Report on Change Feature (Since firmware V1.2) ==
777
778 === 2.8.1 Uplink payload(Enable ROC) ===
779
780
781 Used to Monitor the IDC and VDC increments, and send ROC uplink when the IDC or VDC changes exceed.
782
783 With ROC enabled, the payload is as follows:
784
785 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
786 |(% style="background-color:#4f81bd; color:white; width:97px" %)(((
787
788
789 Size(bytes)
790 )))|(% style="background-color:#4f81bd; color:white; width:48px" %)2|(% style="background-color:#4f81bd; color:white; width:71px" %)2|(% style="background-color:#4f81bd; color:white; width:98px" %)2|(% style="background-color:#4f81bd; color:white; width:73px" %)2|(% style="background-color:#4f81bd; color:white; width:122px" %)1
791 |(% style="width:97px" %)Value|(% style="width:48px" %)[[BAT>>||anchor="H2.3.3BatteryInfo"]]|(% style="width:71px" %)[[Probe Model>>||anchor="H2.3.4ProbeModel"]]|(% style="width:98px" %)[[0 ~~~~ 20mA value>>||anchor="H2.3.507E20mAvalue28IDC_IN29"]]|(% style="width:73px" %)[[0 ~~~~ 30v value>>||anchor="H2.3.607E30Vvalue28pinVDC_IN29"]]|(% style="width:122px" %)(((
792
793
794 [[IN1 &IN2 Interrupt  flag>>||anchor="H2.3.7IN126IN226INTpin"]] & ROC_flag
795 )))
796
797 IN1 &IN2 , Interrupt  flag , ROC_flag:
798
799 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:515px" %)
800 |(% style="background-color:#4f81bd; color:white; width:50px" %)Size(bit)|(% style="background-color:#4f81bd; color:white; width:60px" %)bit7|(% style="background-color:#4f81bd; color:white; width:62px" %)bit6|(% style="background-color:#4f81bd; color:white; width:62px" %)bit5|(% style="background-color:#4f81bd; color:white; width:65px" %)bit4|(% style="background-color:#4f81bd; color:white; width:56px" %)bit3|(% style="background-color:#4f81bd; color:white; width:55px" %)bit2|(% style="background-color:#4f81bd; color:white; width:55px" %)bit1|(% style="background-color:#4f81bd; color:white; width:50px" %)bit0
801 |(% style="width:75px" %)Value|(% style="width:89px" %)IDC_Roc_flagL|(% style="width:46.5834px" %)IDC_Roc_flagH|(% style="width:1px" %)VDC_Roc_flagL|(% style="width:89px" %)VDC_Roc_flagH|(% style="width:89px" %)IN1_pin_level|(% style="width:103px" %)IN2_pin_level|(% style="width:103px" %)Exti_pin_level|(% style="width:103px" %)Exti_status
802
803 * IDC_Roc_flagL
804
805 80 (H): (0x80&0x80)=80(H)=1000 0000(B)  bit7=1, "TRUE", This uplink is triggered when the decrease in the IDC compared to the last ROC refresh exceeds the set threshold.
806
807 60 (H): (0x60&0x80)=0  bit7=0, "FALSE", This uplink is not triggered when the decrease in the IDC compared to the last ROC refresh exceeds the set threshold.
808
809
810 * IDC_Roc_flagH
811
812 60 (H): (0x60&0x40)=60(H)=01000 0000(B)  bit6=1, "TRUE", This uplink is triggered when the increase in the value of the IDC compared to the last ROC refresh exceeds the set threshold.
813
814 80 (H): (0x80&0x40)=0  bit6=0, "FALSE", This uplink is not triggered when the increase in the value of the IDC compared to the last ROC refresh exceeds the set threshold.
815
816
817 * VDC_Roc_flagL
818
819 20 (H): (0x20&0x20)=20(H)=0010 0000(B)  bit5=1, "TRUE", This uplink is triggered when the decrease in the VDC compared to the last ROC refresh exceeds the set threshold.
820
821 90 (H): (0x90&0x20)=0  bit5=0, "FALSE", This uplink is not triggered when the decrease in the VDC compared to the last ROC refresh exceeds the set threshold.
822
823
824 * VDC_Roc_flagH
825
826 90 (H): (0x90&0x10)=10(H)=0001 0000(B)  bit4=1, "TRUE", This uplink is triggered when the increase in the value of the VDC compared to the last ROC refresh exceeds the set threshold.
827
828 20 (H): (0x20&0x10)=0  bit4=0, "FALSE", This uplink is not triggered when the increase in the value of the VDC compared to the last ROC refresh exceeds the set threshold.
829
830
831 * IN1_pin_level & IN2_pin_level
832
833 IN1 and IN2 are used as digital input pins.
834
835 80 (H): (0x80&0x08)=0  IN1 pin is low level.
836
837 80 (H): (0x09&0x04)=0    IN2 pin is low level.
838
839
840 * Exti_pin_level &Exti_status
841
842 This data field shows whether the packet is generated by an interrupt pin.
843
844 Note: The Internet pin of the old motherboard is a separate pin in the screw terminal, and the interrupt pin of the new motherboard(SIB V1.3) is the GPIO_EXTI pin.
845
846 Exti_pin_level:  80 (H): (0x80&0x02)=0  "low", The level of the interrupt pin.
847
848 Exti_status: 80 (H): (0x80&0x01)=0  "False", Normal uplink packet.
849
850
851 === 2.8.2 Set the Report on Change ===
852
853
854 Feature: Get or Set the Report on Change.
855
856
857 ==== 2.8.2.1 Wave alarm mode ====
858
859 Feature: By setting the detection period and a change value, the IDC/VDC variable is monitored whether it exceeds the set change value. If this change value is exceeded, the ROC uplink is sent and the comparison value is flushed.
860
861 * Change value: The amount by which the next detection value increases/decreases relative to the previous detection value.
862 * Comparison value: A parameter to compare with the latest ROC test.
863
864 AT Command: AT+ROC
865
866 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
867 |=(% style="width: 163px; background-color: rgb(79, 129, 189); color: white;" %)Command Example|=(% style="width: 154px; background-color: rgb(79, 129, 189); color: white;" %)Parameters|=(% style="width: 197px; background-color: rgb(79, 129, 189); color: white;" %)Response/Explanation
868 |(% style="width:143px" %)AT+ROC=?|(% style="width:154px" %)Show current ROC setting|(% style="width:197px" %)(((
869
870
871 0,0,0,0(default)
872 OK
873 )))
874 |(% colspan="1" rowspan="4" style="width:143px" %)(((
875
876
877
878
879
880 AT+ROC=a,b,c,d
881 )))|(% style="width:154px" %)(((
882
883
884
885
886
887
888
889 a: Enable or disable the ROC
890 )))|(% style="width:197px" %)(((
891
892
893 0: off
894 1: Turn on the wave alarm mode, send the ROC uplink when the increment exceeds the set parameter and refresh the comparison value.
895
896 2: Turn on the wave alarm mode, send the ROC uplink when the increment exceeds the set parameter and refresh the comparison value. In addition, the comparison value is refreshed when the device sends packets ([[TDC>>||anchor="H3.3.1SetTransmitIntervalTime"]] or [[ACT>>||anchor="H1.7Button26LEDs"]]).
897 )))
898 |(% style="width:154px" %)b: Set the detection interval|(% style="width:197px" %)(((
899
900
901 Range:  0~~65535s
902 )))
903 |(% style="width:154px" %)c: Setting the IDC change value|(% style="width:197px" %)Unit: uA
904 |(% style="width:154px" %)d: Setting the VDC change value|(% style="width:197px" %)Unit: mV
905
906 Example:
907
908 * AT+ROC=0,0,0,0  ~/~/The ROC function is not used.
909 * AT+ROC=1,60,3000, 500  ~/~/ Check value every 60 seconds. lf there is change in IDC (>3mA) or VDC (>500mV), sends an ROC uplink, and the comparison value is refreshed.
910 * AT+ROC=1,60,3000,0  ~/~/ Check value every 60 seconds. lf there is change in IDC (>3mA), send an ROC uplink and the comparison value of IDC is refreshed. dd=0 Means doesn't monitor Voltage.
911 * AT+ROC=2,60,3000,0  ~/~/ Check value every 60 seconds. lf there is change in IDC (>3mA), send an ROC uplink and the comparison value of IDC is refreshed. dd=0 Means doesn't monitor Voltage. In addition, if the change in the IDC does not exceed 3mA, then the ROC uplink is not sent, and the comparison value is not refreshed by the ROC uplink packet. However, if the device TDC time arrives, or if the user manually sends packets, then the IDC comparison value is also refreshed.
912
913 Downlink Command: 0x09 aa bb cc dd
914
915 Format: Function code (0x09) followed by 4 bytes.
916
917 aa: 1 byte; Set the wave alarm mode.
918
919 bb: 2 bytes; Set the detection interval. (second)
920
921 cc: 2 bytes; Setting the IDC change threshold. (uA)
922
923 dd: 2 bytes; Setting the VDC change threshold. (mV)
924
925 Example:
926
927 * Downlink Payload: 09 01 00 3C 0B B8 01 F4  ~/~/Equal to AT+ROC=1,60,3000, 500
928 * Downlink Payload: 09 01 00 3C 0B B8 00 00  ~/~/Equal to AT+ROC=1,60,3000,0
929 * Downlink Payload: 09 02 00 3C 0B B8 00 00  ~/~/Equal to AT+ROC=2,60,3000,0
930
931 Screenshot of parsing example in TTN:
932
933 * AT+ROC=1,60,3000, 500.
934
935 [[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/PS-LB-NA--LoRaWAN_Analog_Sensor_User_Manual/WebHome/image-20241019170902-1.png?width=1454&height=450&rev=1.1||alt="image-20241019170902-1.png"]]
936
937
938 ==== 2.8.2.2 Over-threshold alarm mode ====
939
940 Feature: Monitors whether the IDC/VDC exceeds the threshold by setting the detection period and threshold. Alarm if the threshold is exceeded.
941
942 AT Command: AT+ROC=3,a,b,c,d,e
943
944 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
945 |=(% style="width: 163px; background-color: rgb(79, 129, 189); color: white;" %)Command Example|=(% style="width: 160px; background-color: rgb(79, 129, 189); color: white;" %)Parameters|=(% style="width: 185px; background-color: rgb(79, 129, 189); color: white;" %)Response/Explanation
946 |(% style="width:143px" %)AT+ROC=?|(% style="width:160px" %)Show current ROC setting|(% style="width:185px" %)(((
947
948
949 0,0,0,0(default)
950 OK
951 )))
952 |(% colspan="1" rowspan="5" style="width:143px" %)(((
953
954
955
956
957
958 AT+ROC=3,a,b,c,d,e
959 )))|(% style="width:160px" %)(((
960
961
962 a: Set the detection interval
963 )))|(% style="width:185px" %)(((
964
965
966 Range:  0~~65535s
967 )))
968 |(% style="width:160px" %)b: Set the IDC alarm trigger condition|(% style="width:185px" %)(((
969
970
971 0: Less than the set IDC threshold, Alarm
972
973 1: Greater than the set IDC threshold, Alarm
974 )))
975 |(% style="width:160px" %)(((
976
977
978 c:  IDC alarm threshold
979 )))|(% style="width:185px" %)(((
980
981
982 Unit: uA
983 )))
984 |(% style="width:160px" %)d: Set the VDC alarm trigger condition|(% style="width:185px" %)(((
985
986
987 0: Less than the set VDC threshold, Alarm
988
989 1: Greater than the set VDC threshold, Alarm
990 )))
991 |(% style="width:160px" %)e: VDC alarm threshold|(% style="width:185px" %)Unit: mV
992
993 Example:
994
995 * AT+ROC=3,60,0,3000,0,5000  ~/~/The data is checked every 60 seconds. If the IDC is less than 3mA or the VDC is less than 5000mV, an alarm is generated.
996 * AT+ROC=3,180,1,3000,1,5000  ~/~/The data is checked every 180 seconds. If the IDC is greater than 3mA or the VDC is greater than 5000mV, an alarm is generated.
997 * AT+ROC=3,300,0,3000,1,5000  ~/~/The data is checked every 300 seconds. If the IDC is less than 3mA or the VDC is greater than 5000mV, an alarm is generated.
998
999 Downlink Command: 0x09 03 aa bb cc dd ee
1000
1001 Format: Function code (0x09) followed by 03 and the remaining 5 bytes.
1002
1003 aa: 2 bytes; Set the detection interval.(second)
1004
1005 bb: 1 byte; Set the IDC alarm trigger condition.
1006
1007 cc: 2 bytes; IDC alarm threshold.(uA)
1008
1009
1010 dd: 1 byte; Set the VDC alarm trigger condition.
1011
1012 ee: 2 bytes; VDC alarm threshold.(mV)
1013
1014 Example:
1015
1016 * Downlink Payload: 09 03 00 3C 00 0B B8 00 13 38 ~/~/Equal to AT+ROC=3,60,0,3000,0,5000
1017 * Downlink Payload: 09 03 00 b4 01 0B B8 01 13 38  ~/~/Equal to AT+ROC=3,60,1,3000,1,5000
1018 * Downlink Payload: 09 03 01 2C 00 0B B8 01 13 38  ~/~/Equal to AT+ROC=3,60,0,3000,1,5000
1019
1020 Screenshot of parsing example in TTN:
1021
1022 * AT+ROC=3,60,0,3000,0,5000
1023
1024 [[image:image-20250116180030-2.png]]
1025
1026
1027 == 2.9 ​Firmware Change Log ==
1028
1029
1030 Firmware download link:
1031
1032 [[https:~~/~~/www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0>>url:https://www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0]]
1033
1034
1035 = 3. Configure PS-LB/LS =
1036
1037 == 3.1 Configure Methods ==
1038
1039
1040 PS-LB/LS supports below configure method:
1041
1042 * AT Command via Bluetooth Connection (Recommand Way): [[BLE Configure Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
1043 * AT Command via UART Connection : See [[FAQ>>||anchor="H6.FAQ"]].
1044 * LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>url:http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
1045
1046 == 3.2 General Commands ==
1047
1048
1049 These commands are to configure:
1050
1051 * General system settings like: uplink interval.
1052 * LoRaWAN protocol & radio related command.
1053
1054 They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
1055
1056 [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
1057
1058
1059 == 3.3 Commands special design for PS-LB/LS ==
1060
1061
1062 These commands only valid for PS-LB/LS, as below:
1063
1064
1065 === 3.3.1 Set Transmit Interval Time ===
1066
1067
1068 Feature: Change LoRaWAN End Node Transmit Interval.
1069
1070 AT Command: AT+TDC
1071
1072 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1073 |=(% style="width: 160px; background-color:#4F81BD;color:white" %)Command Example|=(% style="width: 160px; background-color:#4F81BD;color:white" %)Function|=(% style="width: 190px;background-color:#4F81BD;color:white" %)Response
1074 |(% style="background-color:#f2f2f2; width:157px" %)AT+TDC=?|(% style="background-color:#f2f2f2; width:166px" %)Show current transmit Interval|(% style="background-color:#f2f2f2" %)(((
1075
1076
1077 30000
1078 OK
1079 the interval is 30000ms = 30s
1080 )))
1081 |(% style="background-color:#f2f2f2; width:157px" %)AT+TDC=60000|(% style="background-color:#f2f2f2; width:166px" %)Set Transmit Interval|(% style="background-color:#f2f2f2" %)(((
1082
1083
1084 OK
1085 Set transmit interval to 60000ms = 60 seconds
1086 )))
1087
1088 Downlink Command: 0x01
1089
1090 Format: Command Code (0x01) followed by 3 bytes time value.
1091
1092 If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
1093
1094 * Example 1: Downlink Payload: 0100001E  ~/~/  Set Transmit Interval (TDC) = 30 seconds
1095 * Example 2: Downlink Payload: 0100003C  ~/~/  Set Transmit Interval (TDC) = 60 seconds
1096
1097 === 3.3.2 Set Interrupt Mode ===
1098
1099
1100 Feature, Set Interrupt mode for GPIO_EXIT.
1101
1102 AT Command: AT+INTMOD
1103
1104 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1105 |=(% style="width: 154px;background-color:#4F81BD;color:white" %)Command Example|=(% style="width: 196px;background-color:#4F81BD;color:white" %)Function|=(% style="width: 160px;background-color:#4F81BD;color:white" %)Response
1106 |(% style="background-color:#f2f2f2; width:154px" %)AT+INTMOD=?|(% style="background-color:#f2f2f2; width:196px" %)Show current interrupt mode|(% style="background-color:#f2f2f2; width:157px" %)(((
1107
1108
1109 0
1110 OK
1111 the mode is 0 =Disable Interrupt
1112 )))
1113 |(% style="background-color:#f2f2f2; width:154px" %)AT+INTMOD=2|(% style="background-color:#f2f2f2; width:196px" %)(((
1114
1115
1116 Set Transmit Interval
1117 0. (Disable Interrupt),
1118 ~1. (Trigger by rising and falling edge)
1119 2. (Trigger by falling edge)
1120 3. (Trigger by rising edge)
1121 )))|(% style="background-color:#f2f2f2; width:157px" %)OK
1122
1123 Downlink Command: 0x06
1124
1125 Format: Command Code (0x06) followed by 3 bytes.
1126
1127 This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
1128
1129 * Example 1: Downlink Payload: 06000000  ~/~/  Turn off interrupt mode
1130 * Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
1131
1132 === 3.3.3 Set the output time ===
1133
1134
1135 Feature, Control the output 3V3 , 5V or 12V.
1136
1137 AT Command: AT+3V3T
1138
1139 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:474px" %)
1140 |=(% style="width: 154px;background-color:#4F81BD;color:white" %)Command Example|=(% style="width: 201px;background-color:#4F81BD;color:white" %)Function|=(% style="width: 119px;background-color:#4F81BD;color:white" %)Response
1141 |(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=?|(% style="background-color:#f2f2f2; width:201px" %)Show 3V3 open time.|(% style="background-color:#f2f2f2; width:116px" %)(((
1142
1143
1144 0
1145 OK
1146 )))
1147 |(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=0|(% style="background-color:#f2f2f2; width:201px" %)Normally open 3V3 power supply.|(% style="background-color:#f2f2f2; width:116px" %)(((
1148
1149
1150 OK
1151 default setting
1152 )))
1153 |(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=1000|(% style="background-color:#f2f2f2; width:201px" %)Close after a delay of 1000 milliseconds.|(% style="background-color:#f2f2f2; width:116px" %)(((
1154
1155
1156 OK
1157 )))
1158 |(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=65535|(% style="background-color:#f2f2f2; width:201px" %)Normally closed 3V3 power supply.|(% style="background-color:#f2f2f2; width:116px" %)(((
1159
1160
1161 OK
1162 )))
1163
1164 AT Command: AT+5VT
1165
1166 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:470px" %)
1167 |=(% style="width: 155px;background-color:#4F81BD;color:white" %)Command Example|=(% style="width: 196px;background-color:#4F81BD;color:white" %)Function|=(% style="width: 119px;background-color:#4F81BD;color:white" %)Response
1168 |(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=?|(% style="background-color:#f2f2f2; width:196px" %)Show 5V open time.|(% style="background-color:#f2f2f2; width:114px" %)(((
1169
1170
1171 0
1172 OK
1173 )))
1174 |(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=0|(% style="background-color:#f2f2f2; width:196px" %)Normally closed 5V power supply.|(% style="background-color:#f2f2f2; width:114px" %)(((
1175
1176
1177 OK
1178 default setting
1179 )))
1180 |(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=1000|(% style="background-color:#f2f2f2; width:196px" %)Close after a delay of 1000 milliseconds.|(% style="background-color:#f2f2f2; width:114px" %)(((
1181
1182
1183 OK
1184 )))
1185 |(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=65535|(% style="background-color:#f2f2f2; width:196px" %)Normally open 5V power supply.|(% style="background-color:#f2f2f2; width:114px" %)(((
1186
1187
1188 OK
1189 )))
1190
1191 AT Command: AT+12VT
1192
1193 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:443px" %)
1194 |=(% style="width: 156px;background-color:#4F81BD;color:white" %)Command Example|=(% style="width: 199px;background-color:#4F81BD;color:white" %)Function|=(% style="width: 88px;background-color:#4F81BD;color:white" %)Response
1195 |(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=?|(% style="background-color:#f2f2f2; width:199px" %)Show 12V open time.|(% style="background-color:#f2f2f2; width:83px" %)(((
1196
1197
1198 0
1199 OK
1200 )))
1201 |(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=0|(% style="background-color:#f2f2f2; width:199px" %)Normally closed 12V power supply.|(% style="background-color:#f2f2f2; width:83px" %)OK
1202 |(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=500|(% style="background-color:#f2f2f2; width:199px" %)Close after a delay of 500 milliseconds.|(% style="background-color:#f2f2f2; width:83px" %)(((
1203
1204
1205 OK
1206 )))
1207
1208 Downlink Command: 0x07
1209
1210 Format: Command Code (0x07) followed by 3 bytes.
1211
1212 The first byte is which power, the second and third bytes are the time to turn on.
1213
1214 * Example 1: Downlink Payload: 070101F4  ~-~-->  AT+3V3T=500
1215 * Example 2: Downlink Payload: 0701FFFF   ~-~-->  AT+3V3T=65535
1216 * Example 3: Downlink Payload: 070203E8  ~-~-->  AT+5VT=1000
1217 * Example 4: Downlink Payload: 07020000  ~-~-->  AT+5VT=0
1218 * Example 5: Downlink Payload: 070301F4  ~-~-->  AT+12VT=500
1219 * Example 6: Downlink Payload: 07030000  ~-~-->  AT+12VT=0
1220
1221 Note: Before v1.2, the maximum settable time of 3V3T, 5VT and 12VT is 65535 milliseconds. After v1.2, the maximum settable time of 3V3T, 5VT and 12VT is 180 seconds.
1222
1223 Therefore, the corresponding downlink command is increased by one byte to five bytes.
1224
1225 Example:
1226
1227 * 120s=120000ms(D) =0x01D4C0(H), Downlink Payload: 07 01 01 D4 C0  ~-~-->  AT+3V3T=120000
1228 * 100s=100000ms(D) =0x0186A0(H), Downlink Payload: 07 02 01 86 A0  ~-~-->  AT+5VT=100000
1229 * 80s=80000ms(D) =0x013880(H), Downlink Payload: 07 03 01 38 80  ~-~-->  AT+12VT=80000
1230
1231 === 3.3.4 Set the Probe Model ===
1232
1233
1234 Users need to configure this parameter according to the type of external probe. In this way, the server can decode according to this value, and convert the current value output by the sensor into water depth or pressure value.
1235
1236 AT Command: AT +PROBE
1237
1238 AT+PROBE=aabb
1239
1240 When aa=00, it is the water depth mode, and the current is converted into the water depth value; bb is the probe at a depth of several meters.
1241
1242 When aa=01, it is the pressure mode, which converts the current into a pressure value;
1243
1244 bb represents which type of pressure sensor it is.
1245
1246 (A->01,B->02,C->03,D->04,E->05,F->06,G->07,H->08,I->09,J->0A,K->0B,L->0C)
1247
1248 When aa=02, it is the Differential Pressure Sensor , which converts the current into a pressure value;
1249
1250 bb represents which type of pressure sensor it is.
1251
1252 (0~~100Pa->01,0~~200Pa->02,0~~300Pa->03,0~~1KPa->04,0~~2KPa->05,0~~3KPa->06,0~~4KPa->07,0~~5KPa->08,0~~10KPa->09,-100~~ 100Pa->0A,-200~~ 200Pa->0B,-1~~ 1KPa->0C)
1253
1254 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1255 |(% style="background-color:#4f81bd; color:white; width:154px" %)Command Example|(% style="background-color:#4f81bd; color:white; width:269px" %)Function|(% style="background-color:#4f81bd; color:white" %)Response
1256 |(% style="background-color:#f2f2f2; width:154px" %)AT+PROBE=?|(% style="background-color:#f2f2f2; width:269px" %)Get or Set the probe model.|(% style="background-color:#f2f2f2" %)0
1257 OK
1258 |(% style="background-color:#f2f2f2; width:154px" %)AT+PROBE=0003|(% style="background-color:#f2f2f2; width:269px" %)Set water depth sensor mode, 3m type.|(% style="background-color:#f2f2f2" %)OK
1259 |(% style="background-color:#f2f2f2; width:154px" %)(((
1260
1261
1262 AT+PROBE=000A
1263 )))|(% style="background-color:#f2f2f2; width:269px" %)Set water depth sensor mode, 10m type.|(% style="background-color:#f2f2f2" %)OK
1264 |(% style="background-color:#f2f2f2; width:154px" %)AT+PROBE=0064|(% style="background-color:#f2f2f2; width:269px" %)Set water depth sensor mode, 100m type.|(% style="background-color:#f2f2f2" %)OK
1265 |(% style="background-color:#f2f2f2; width:154px" %)AT+PROBE=0101|(% style="background-color:#f2f2f2; width:269px" %)Set pressure transmitters mode, first type(A).|(% style="background-color:#f2f2f2" %)OK
1266 |(% style="background-color:#f2f2f2; width:154px" %)AT+PROBE=0000|(% style="background-color:#f2f2f2; width:269px" %)Initial state, no settings.|(% style="background-color:#f2f2f2" %)OK
1267
1268 Downlink Command: 0x08
1269
1270 Format: Command Code (0x08) followed by 2 bytes.
1271
1272 * Example 1: Downlink Payload: 080003  ~-~-->  AT+PROBE=0003
1273 * Example 2: Downlink Payload: 080101  ~-~-->  AT+PROBE=0101
1274
1275 === 3.3.5 Multiple collections are one uplink (Since firmware V1.1) ===
1276
1277
1278 Added AT+STDC command to collect the voltage of VDC_INPUT/IDC_INPUT multiple times and upload it at one time.
1279
1280 AT Command: AT +STDC
1281
1282 AT+STDC=aa,bb,bb
1283
1284 aa:
1285 0: means disable this function and use TDC to send packets.
1286 1: means that the function is enabled to send packets by collecting VDC data for multiple times.
1287 2: means that the function is enabled to send packets by collecting IDC data for multiple times.
1288 bb: Each collection interval (s), the value is 1~~65535
1289 cc: the number of collection times, the value is 1~~120
1290
1291 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1292 |(% style="background-color:#4f81bd; color:white; width:160px" %)Command Example|(% style="background-color:#4f81bd; color:white; width:215px" %)Function|(% style="background-color:#4f81bd; color:white" %)Response
1293 |(% style="background-color:#f2f2f2; width:160px" %)AT+STDC=?|(% style="background-color:#f2f2f2; width:215px" %)Get the mode of multiple acquisitions and one uplink.|(% style="background-color:#f2f2f2" %)1,10,18
1294 OK
1295 |(% style="background-color:#f2f2f2; width:160px" %)AT+STDC=1,10,18|(% style="background-color:#f2f2f2; width:215px" %)Set the mode of multiple acquisitions and one uplink, collect once every 10 seconds, and report after 18 times.|(% style="background-color:#f2f2f2" %)(((
1296
1297
1298 Attention:Take effect after ATZ
1299
1300 OK
1301 )))
1302 |(% style="background-color:#f2f2f2; width:160px" %)AT+STDC=0, 0,0|(% style="background-color:#f2f2f2; width:215px" %)(((
1303
1304
1305 Use the TDC interval to send packets.(default)
1306
1307
1308 )))|(% style="background-color:#f2f2f2" %)(((
1309
1310
1311 Attention:Take effect after ATZ
1312
1313 OK
1314 )))
1315
1316 Downlink Command: 0xAE
1317
1318 Format: Command Code (0xAE) followed by 4 bytes.
1319
1320 * Example 1: Downlink Payload: AE 01 02 58 12 ~-~-->  AT+STDC=1,600,18
1321
1322 = 4. Battery & Power Consumption =
1323
1324
1325 PS-LB use ER26500 + SPC1520 battery pack and PS-LS use 3000mAh Recharable Battery with Solar Panel. See below link for detail information about the battery info and how to replace.
1326
1327 [[Battery Info & Power Consumption Analyze>>url:http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
1328
1329
1330 = 5. OTA firmware update =
1331
1332
1333 Please see this link for how to do OTA firmware update: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
1334
1335
1336 = 6. FAQ =
1337
1338 == 6.1 How to use AT Command via UART to access device? ==
1339
1340
1341 See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
1342
1343
1344 == 6.2 How to update firmware via UART port? ==
1345
1346
1347 See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
1348
1349
1350 == 6.3 How to change the LoRa Frequency Bands/Region? ==
1351
1352
1353 You can follow the instructions for [[how to upgrade image>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]].
1354 When downloading the images, choose the required image file for download. ​
1355
1356
1357 == 6.4 How to measure the depth of other liquids other than water? ==
1358
1359
1360 Test the current values at the depth of different liquids and convert them to a linear scale.
1361 Replace its ratio with the ratio of water to current in the decoder.
1362
1363 Example:
1364
1365 Measure the corresponding current of the sensor when the liquid depth is 2.04m and 0.51m.
1366
1367 Calculate scale factor：
1368 Use these two data to calculate the current and depth scaling factors：(7.888-5.035)/(2.04-0.51)=1.86470588235294
1369
1370 Calculation formula：
1371
1372 Use the calibration formula：(Current current - Minimum calibration current)/Scale factor + Minimum actual calibration height
1373
1374 Actual calculations：
1375
1376 Use this formula to calculate the value corresponding to the current at a depth of 1.5 meters: (6.918-5.035)/1.86470588235294+0.51=1.519810726
1377
1378 Error：
1379
1380 0.009810726
1381
1382
1383 [[image:image-20240329175044-1.png]]
1384
1385 = 7. Troubleshooting =
1386
1387 == 7.1 Water Depth Always shows 0 in payload ==
1388
1389
1390 If your device's IDC_intput_mA is normal, but your reading always shows 0, please refer to the following points:
1391
1392 ~1. Please set it to mod1
1393
1394 2. Please set the command [[AT+PROBE>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/PS-LB%20--%20LoRaWAN%20Pressure%20Sensor/#H3.3.4SettheProbeModel]] according to the model of your sensor
1395
1396 3. Check the connection status of the sensor
1397
1398
1399 = 8. Order Info =
1400
1401
1402
1403 [[image:image-20241021093209-1.png]]
1404
1405 = 9. ​Packing Info =
1406
1407
1408 Package Includes:
1409
1410 * PS-LB or PS-LS LoRaWAN Pressure Sensor
1411
1412 Dimension and weight:
1413
1414 * Device Size: cm
1415 * Device Weight: g
1416 * Package Size / pcs : cm
1417 * Weight / pcs : g
1418
1419 = 10. Support =
1420
1421
1422 * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
1423
1424 * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[Support@dragino.cc>>mailto:Support@dragino.cc]].