LTS5 LoRa HMI Touch Screen

The LTS5 is a (% style="color:blue" %)**LoRa / LoRaWAN HMI Touch Screen**(%%) designed for displaying information in IoT projects. It features a **5.0-inch HMI touch screen** and supports **Wi-Fi**, **Bluetooth**, and **LoRa** wireless protocols.

27

28

The LTS5 is an open-source software project powered by an **ESP32 MCU** and a **Dragino LA66 LoRa** module. The extensive development resources available for ESP32 can significantly reduce development time.

29

30

The LTS5's HMI touch screen supports **drag-and-drop** design, allowing developers to use SquareLine to easily customize the display UI for various applications.

31

32

The LA66 LoRa module can be programmed to support either private LoRa protocols or the LoRaWAN protocol.

== 1.2 Features ==

* ESP32-WROOM MCU: 8MB RAM & 16MB ROM

38

* Dragino LA66 LoRa Module

39

* Support Private LoRa protocol or LoRaWAN protocol

40

* Support WiFi & BLE wireless protocol

41

* 5.0" HMI touch screen

42

* Support LVGL case. SquareLine program.

43

* Support RS485 Interface

44

* Open Source Project

* Wall Attachable.

* 5V DC power

* IP Rating: IP52

== 1.3 Specifications ==

**LoRa**:

* Frequency Range: 870 MHz ~~ 960 MHz

55

* TCXO crystal to ensure RF performance on low temperature

56

* Maximum Power +22 dBm constant RF output

57

* High sensitivity: -148 dBm

58

* LoRa Tx Current: <90 mA at +17 dBm, 108 mA at +22 dBm

59

* LoRa Rx current: <9 mA

**WiFi:**

* 802.11b/g/n

* Up to 150 Mbps data rate in 802.11n mode

65

* Support A-MPDU and A-MSDU aggregation

66

* zero point four μ S protection interval

67

* Working channel center frequency range: 2412~~2484 MHz

**Bluetooth:**

* Bluetooth V4.2 BR/EDR and Bluetooth LE standard

72

* Class-1, Class-2, and Class-3 transmitters.

* AFH

* CVSD and SBC

**Display:**

* 5.0 Inch , 800 x 480

79

* IPS Capacitive Touch SCreen

80

* RGB color.

81

* Display Area: 120.7*75.80 mm

82

83

== 1.4 Power Consumption ==

84

85

86

* External 5V DC power adapter

87

88

== 1.5 Storage & Operation Temperature ==

89

90

91

* Operation Temperature: -20 ~~ 70°C (No Dew)

92

* Storage Temperature: -30 ~~ 70°C (No Dew)

93

94

== 1.6 Applications ==

95

96

97

* Smart Buildings & Home Automation

98

* Logistics and Supply Chain Management

* Smart Metering

* Smart Agriculture

* Smart Cities

* Smart Factory

= 2. Getting Started with 'Hello World' =

105

106

== 2.1 About this demo ==

107

108

109

This getting started example demonstrates how to design and deploy a simple display UI for the LTS5 device. The example includes:

110

111

* Creating a basic UI with a single button.

112

* Implementing functionality to navigate the Web UI to a new page when the button is clicked.

113

* Uploading the UI to the LTS5 device.

114

115

By completing this demo, you will gain foundational knowledge for customizing the LTS5 interface and building more advanced IoT applications.

116

117

118

== 2.2 Install Software Running Environment ==

119

120

121

The **ESP MCU** supports development with **ESP-IDF**, **Arduino**, or **MicroPython**. We use **ESP-IDF** for compilation and **Visual Studio Code (VS Code)** as the development environment for this project.

122

123

124

=== 2.2.1 Install VS Code and ESP-IDF extension ===

125

126

127

First, download and install **VS Code** for your operating system from the Visual Studio Code website: [[Visual Studio Code - Mac, Linux, Windows>>https://code.visualstudio.com/download]].

128

129

Next, install the **ESP-IDF** extension within **VS Code**. Detailed steps for this process are shown in Image 1.

130

131

132

[[image:image-20240928110211-5.png||height="508" width="866"]]

133

134

Image 1: ESP-IDF extension install

135

136

Links for reference: [[Install ESP32 ESP-IDF on Windows and Integrate with VS code (esp32tutorials.com)>>url:https://esp32tutorials.com/install-esp32-esp-idf-windows-integrate-vs-code/#:~~:text=In%20this%20tutorial,%20we%20will%20show%20you%20how%20to%20install]]

137

138

139

=== 2.2.2 Install SquareLine Studio ===

140

141

142

Download and install the latest version of [[SquareLine Studio>>https://squareline.io/downloads#lastRelease]] on your computer. It supports Windows, Linux, and Mac OS. The software version we are using here is 1.5.0. See the image below.

143

144

[[image:squareline.io_downloads.png||height="888" width="1294"]]

145

146

147

After installation, you can use SquareLine Studio with a **PERSONAL license plan**. Click **LOG IN** and create a free account using your email address. Then activate your PERSONAL license plan for free. You don’t need to provide any credit card information. However, the PERSONAL license plan has the following limitations:

* Max. 10 screens

* Max. 150 widgets

* Max. 5 global colors

* Max. 2 themes

* Max. 1 component

== 2.3 Simple usage of SquareLine Studio and exporting UI code ==

156

157

158

Start the SquareLine Studio. The **launcher screen** appears as shown in the below image. You can create a new project by clicking **Create** in the top menu. Then select the **Desktop** tab. Select the development platform, **Eclipse with SDL for development on PC**.

159

160

* In the **PROJECT SETTINGS**, select **LVGL version **as **8.3.11** and **Resolution** as **800** x **480**.

161

* Select the **CREATE **button to create the new project with the selected settings.

162

163

[[image:squareline-studio-launcher-screen.png||height="752" width="1415"]]

164

165

166

Next, you need to configure some additional settings for this project. To do so, select** File -> Project Settings** as shown in the image below.

167

168

[[image:1727229582471-566.png]]

169

170

171

In the **PROJECT SETTINGS** dialog box, configure/modify the project settings as shown in the image below.

172

173

* **UI Files Export Root**: Select a folder on your computer to store the UI files.

174

* **LVGL Include Path**: Set this to **lvgl.h**

175

* Click on the **APPLY CHANGES** button.

176

177

[[image:image-20240928105309-4.png||height="526" width="556"]]

178

179

180

Now you can start building the user interface. Follow the steps below:

181

182

183

=== **Add widgets** ===

184

185

186

To add a widget, navigate to the **Widgets** panel, and then click on the widget you want to add to the screen. You can reposition the widgets in the screen area by clicking and dragging them. Now add a **Label**, **Button**, and **Image** as shown in the image below. The added widgets are also displayed in the **Hierarchy **panel.

187

188

[[image:image-20240928111412-6.png||height="526" width="864"]]

189

190

191

Then click the **Screen **widget to add the second screen. After adding the second screen, it will appear in the Screens panel as **Screen2**.

192

193

[[image:Screenshot 2024-12-24 140459.png||height="278" width="290"]]

194

195

=== **Modify widget properties** ===

196

197

198

The area for modifying widgets is called the **Inspector** panel. The Inspector panel consists of four sections: **COMPONENT**, **<WIDGET>**, **STYLE SETTINGS**, and **EVENTS**, as shown in the image below. The second section allows you to adjust a widget's layout, size, position, alignment, flags, states, and more. When you select a widget on the screen, the name of this section changes to match the name of the selected widget.

199

200

[[image:1727485118799-984.png]]

201

202

203

==== **Changing the Button properties** ====

204

205

206

Click the **Button **you have added to the screen. Under the **Layout** you can change the button's position and size. Use the following settings:

207

208

* **Flex Flow**: No Layout

* **Transform**:

** **X**: 331 px

** **Y**: 203 px

** **Width**: 100 px

** **Height**: 50 px

** **Align**: CENTER

[[image:1727485251053-655.png]]

217

218

219

Next, add a click event to the button. When the button is clicked, an event should trigger to change the current screen (Screen1) to a new screen (Screen2) with a fade effect and the transition from Screen1 to Screen2 should take 500ms.

220

221

* Click **ADD EVENT** button. A new section will appear to configure this event.

222

223

[[image:Screenshot 2024-12-24 134937.png||height="80" width="290"]]

224

225

* Select **CLICKED** from the dropdown under **Trigger**. Choose **CHANGE SCREEN** under **Action**, then click the **ADD** button. A new section will appear to configure the action.

226

227

[[image:Screenshot 2024-12-24 134818.png||height="222" width="290"]]

228

229

* Select **Screen2** under **Screen to**. Select **FADE ON** from **Fade mode**. The default value **500** means the transition takes 500 milliseconds to appear the Screen2.

230

* Finally, click the **ADD** button.

231

232

[[image:1727485480434-713.png||height="395" width="290"]]

233

234

Image 8: Add an event for the button

235

236

237

==== **Changing the label properties** ====

238

239

240

Click the Label you have added to the screen. Under the **Label** section, type "**Click for Detail**" in the **Text** textbox.

241

242

[[image:image-20240928090825-1.png||height="327" width="391"]]

243

244

245

Once you enter the text, it will immediately appear on the label.

246

247

248

==== **Changing image properties** ====

249

250

251

To use the **Image **widget, you should first add an image to your project. The image format must be PNG, and its resolution should not exceed 800x480 pixels. There are two ways to add an image file.

252

253

One way is to move your image into the folder "…/squareline project/assets/", as shown in the image below.

254

255

[[image:image-20240928113424-9.png||height="355" width="505"]]

256

257

258

The other way is to click the "**ADD FILE INTO ASSETS**" button, then select an image from your computer to import. After adding, you can see the image in the "**assets**" panel in SquareLine Studio, as shown in the image below.

259

260

[[image:image-20240928114139-10.png||height="559" width="810"]]

261

262

263

==== **The relationship between widgets** ====

264

265

266

Widgets commonly have two types of relationships: **parallel** and **parent-child**.

267

268

* In a **parallel relationship**, widgets' positions are determined relative to a shared reference object.

269

* In a **parent-child relationship**, any part of the child object outside the parent's boundaries is hidden by default. To make the child object fully visible, you must adjust its position to fit within the parent's range.

270

271

[[image:1727486567182-334.png||height="318" width="278"]]

272

273

274

Move the label, **Label1** to make it a child of **Button1** as shown in the image below.

275

276

[[image:image-20240928112001-8.png||height="431" width="796"]]

277

278

279

Then set the **X** and **Y** position of the label to **0** as shown in the image below. The label will appear on the button. If you move the button on the screen, the label will move along with it as part of the button.

280

281

[[image:Screenshot 2024-12-24 144005.png||height="360" width="290"]]

282

283

284

==== **Preview the screen** ====

285

286

287

You can test the result by clicking on the **PLAY** button as shown in the image below. The screen will change into play mode.

288

289

[[image:1727487368023-281.png]]

290

291

292

For more information, please visit the official link: [[SquareLine Studio 1.4.2 Documentation ~| SquareLine Studio>>url:https://docs.squareline.io/docs/squareline/]].

293

294

295

== 2.4 Integrate UI Code to ESP-IDF Project ==

296

297

298

To integrate, first export the UI code, then make some modifications, and finally relocate the UI code to a specific position within the project.

299

300

On the menubar, click **Export -> Export UI** Files as shown in the image below.

301

302

[[image:1727229798126-306.png]]

303

304

305

The exported UI files can be found in your SquareLine project folder as shown in the image below.

306

307

308

[[image:1727229821582-258.png||height="333" width="662"]]

309

310

311

Create a new folder named "**ui**" at path "**basic_prj/app_components/ui/**", and copy all the exported UI code into it as shown in the image below.

312

313

[[image:image-20240928144830-11.png]]

314

315

316

Open the **CMakeLists.txt** file and edit it as ahown below.

317

318

[[image:1727229892636-154.png||height="521" width="407"]]

319

320

321

Open the main.c file and add two lines of code as shown in the below images.

322

323

Add **#include "ui.h"**

324

325

[[image:1727229926561-300.png]]

Add **ui_init();**

[[image:1727229955611-607.png]]

331

332

333

== 2.5 Brief introduction to the Hello World project ==

334

335

336

The project consists of two screens. The first screen displays the company's logo, the project name, and a button to navigate to the next screen. The second screen provides information about the HMI screen product through an image and includes a button to return to the previous screen.

337

338

339

== 2.6 Test Result ==

340

341

342

By pressing the button located at the bottom right, the screen switches to the next one as expected. This confirms that the UI file has been successfully integrated into the project and is functioning correctly.

Screen 1:

[[image:1727488067077-684.png||height="402" width="574"]]

Screen 2:

[[image:1727488157579-949.png||height="397" width="572"]]

352

353

354

= 3. Example Project 1: LoRa Central Display =

355

356

[[image:image-20240916101737-1.png||height="468" width="683"]]

357

358

359

= 4. Example Project 2: LoRaWAN RS485 Alarm =

360

361

= 5. Example Project 3: P2P =

362

363

The project achieves the function of receiving LoRa P2P messages and displaying them on the screen. The workflow is as follows: A LA66, running a P2P program, sends a message in a particular format via an AT command. Then, the LTS5 receives the message and displays it on the screen.

364

365

The project can be found at [[this link>>url:https://github.com/dragino/LoRa-HMI-Touch-Screen/tree/main/Example/P2P]].

366

367

== 5.1 firmware flashing approach. ==

368

369

5.1.1 Download this project

370

371

5.1.2 Download esp32 firmware flash tool in [[this link>>https://docs.espressif.com/projects/esp-test-tools/en/latest/esp32/production_stage/tools/flash_download_tool.html]].

372

373

5.1.3 Download la66 firmware flash tool in [[this link>>https://www.dropbox.com/scl/fo/9kqeqf6wmet10o9hgxuwa/h?rlkey=4ikrg6kg5v0yjxwhp0i37wrv7&e=1&dl=0]].

374

375

5.1.4 Upload firmware to esp32

376

377

Open flash_download_tool.exe, and then follow the steps below.

378

379

[[image:1738893226894-758.png||height="170" width="176"]]

380

381

[[image:image-20250207100150-7.png||height="476" width="538"]]

382

383

5.1.5 Upload firmware to la66

384

385

Open Dragino_Sensor_Manager_Utility.exe, and then follow the steps below.

386

387

[[image:image-20250207101415-8.png||height="522" width="618"]]

388

389

[[image:image-20250207101515-9.png||height="522" width="618"]]

390

391

== 5.2 AT command and P2P data format ==

392

393

AT+SEND=1,014b69746368656e2d467269676531FFFFA84041000181D4A8**01**A4CBBB0A8E085C02,0,3

394

395

AT+SEND=1,014b69746368656e2d467269676531FFFFA84041000181D4A8**02**A4CB00,0,3

396

397

AT+SEND=1,014b69746368656e2d467269676531FFFFA84041000181D4A8**03**A4CB00,0,3

398

399

AT+SEND=1,014b69746368656e2d467269676531FFFFA84041000181D4A8**04**A4CB00,0,3

400

401

AT+SEND=1,014b69746368656e2d467269676531FFFFA84041000181D4A8**05**A4CB00,0,3

402

403

AT+SEND=1,014b69746368656e2d467269676531FFFFA84041000181D4A8**06**A4CB00,0,3

**Data format**:

~1. AT+SEND=1,**01** **4b69746368656e2d467269676531FFFF A84041000181D4A8 01 A4CB BB0A 8E08 5C02**,0,3

408

409

**01:** encrypt. 1 Byte. 01 ~-~-> no encryption. This 1-byte information is now invalid; simply write 0x01 instead.

410

411

**4b69746368656e2d467269676531FFFF: **Device Name. 16 Bytes. The Device Name for this piece of information is "Kitchen-Frige1," and the subsequent "FFFF" is intended to pad it up to 16 Bytes. The Device Name for this piece of information is 'Kitchen-Frige1,' and the subsequent 'FFFF' is intended to pad it up to 16 Bytes, but it is not necessary as the system can handle shorter names as well.

412

413

**A84041000181D4A8:** Device EUI. 8 Bytes. The last three Bytes will be extracted by the ESP32-S3 and displayed on the screen.

414

415

**01: **Panel Type. 1 Byte. 0x01~-~->Tem & Hum,

0x02~-~->Door,

0x03~-~->Water Leak,

0x04~-~->Occupied,

0x05~-~->Button,

0x06~-~->Alarm,

**A4CB: **Battery level//. //2 Bytes. Battery Voltage =0xCBA4&0x3FFF=0x0BA4=2980mV

428

429

**BB0A: **The temperature of the built-in sensor in LHT65N.// //2 Bytes. Temperature: 0x0ABB/100=27.47℃

430

431

**8E08: **The temperature of the External temperature sensor.// //2 Bytes. Temperature: 0x088E/100=21.90℃

432

433

**5C02：**The humidity of the built-in sensor in LHT65N. 2 Bytes. Humidity: 0x025C/10=60.4%

434

435

2. AT+SEND=1,**01** **4b69746368656e2d467269676531FFFF** **A84041000181D4A8** **02 A4CB 00**,0,3

436

437

Specific sections of the data share the same function.

438

439

**00: Status. **1 Byte//. //If Panel Type is 0x02, **Status: 00~-~->Open; 01~-~->Close.**

440

441

If Panel Type is 0x03, **Status: 00~-~->Normal; 01~-~->Water Leaking.**

442

443

If Panel Type is 0x04, **Status: 00~-~->Free; 01~-~->Occupied.**

444

445

If Panel Type is 0x05, **Status: 00~-~->OFF; 01~-~->ON.**

446

447

If Panel Type is 0x06, **Status: 00~-~->OFF; 01~-~->Alarm.**

== 5.3 Usage ==

After burning the firmware into LTS5, you can use an LA66 equipped with peer-to-peer firmware to send data to LTS5 via AT commands.

452

453

5.3.1 Connect LA66 to the computer, open Serial Port Utility, and send the AT+CFG instruction to check whether the LA66 has downloaded correct program.

454

455

[[image:image-20250207143131-11.png||height="527" width="547"]]

456

457

5.3.2 Copy an AT instruction example, click "Send" button, then the led in LA66 will flash and the LTS5 will display the LoRa information.

458

459

[[image:image-20250207144605-12.png||height="634" width="548"]]

460

461

= 6. Example Project 4: LoRaWAN_CLASS_C =

462

463

464

The project achieves the function of receiving LoRaWAN Class C messages and displaying them on the screen. Note: The Things Network (TTN) needs to enable Class C support, and the LA66 within the LTS5 needs to operate in Class C mode.

465

466

The downlink workflow proceeds as follows: The Things Network (TTN) sends a message in a specific format via downlink. Then, a LoRaWAN gateway relays this message to the LTS5. Finally, the LTS5 receives the message and displays it on its screen.

467

468

The uplink workflow is as follows: The LA66 within the LTS5 sends a LoRaWAN message, for some reason, to a LoRaWAN gateway, which then forwards it to The Things Network (TTN).

469

470

The project can be found at [[this link>>https://github.com/dragino/LoRa-HMI-Touch-Screen/tree/main/Example/LoRaWAN_CLASS_C]].

471

472

== 6.1 firmware flashing approach ==

473

474

The firmware flashing approach is the same as described in section [[5.1>>5.1]].

== 6.2 flowchart ==

[[image:image-20250207164320-13.png||height="696" width="1344"]]

== 6.3 Usage ==

6.3.1 TTN downlink panel data to display in LTS5

483

484

6.3.1 Connect LA66 to the computer, open Serial Port Utility, and send the AT+CFG instruction to check whether the LA66 has downloaded correct program.

485

486

[[image:image-20250207165702-14.png||height="830" width="563"]]

487

488

6.3.2 Switch to Class C using "AT+CLASS=C", and check the class with "AT+CLASS=?".

489

490

[[image:image-20250207173212-27.png]]

491

492

[[image:image-20250207172246-20.png]]

493

494

6.3.3 Verify LA66's join status (in LTS5) with "AT+NJS=?". If not joined, connect manually to LoRaWAN with "AT+JOIN".

495

496

[[image:image-20250207172010-19.png]]

497

498

[[image:image-20250207171650-17.png]]

499

500

6.3.4 After joining, send a message to TTN, such as "AT+SENDB=01,02,8,05820802581ea0a5", to activate communication.

501

502

[[image:image-20250207192107-28.png]]

503

504

6.3.5 TTN distributes panel data in three batches.

505

506

1. downlink DEUI F1A84041000181D4A8

507

1. downlink Dev Name F24B69746368656E2D467269676531FFFF

508

1. downlink Sensor Data 5501A4CBBB0A8E085C02 或 5504A4CB01

509

510

= 5. The method for adding a new type of panel to the project =

511

512

If you don't have this need, then this part of the content can be ignored.

513

514

1. Design a panel in SquareLine Studio, as shown in Image 5.1 below for reference.

515

516

[[image:image-20241121113445-1.png||height="584" width="934"]]

517

518

Image 5.1: a panel about water_leak

519

520

521

2. **Export the UI file: **You need to adjust the export path first, then click '**Export -> Export UI Files**' on the menu bar. This step was introduced earlier. After that, you can get the UI files as shown in Image 5.2.

522

523

[[image:image-20241121141120-4.png||height="383" width="795"]]

524

525

Image 5.2: Exported UI files

526

527

528

3. **Delete and rename some file.** Here are the steps:

529

530

Step 1: Delete the 'components' directory.

531

Step 2: Delete 'filelist.txt'.

532

Step 3: Delete 'ui_helpers.c' and 'ui_helpers.h'.

533

Step 4: Rename 'ui_ScreenMain.c' in the 'screens' directory to 'ui_water_leak_style.c'.

534

Step 5: Rename the 'screens' directory to 'styles'.

535

536

[[image:image-20241121151934-10.png||height="303" width="792"]]

537

538

image 5.3 rest file (1)

539

540

[[image:image-20241121142925-7.png||height="141" width="793"]]

541

542

image 5.4 rest file (2)

543

544

4. Open the project in **VS Code**.

545

546

5. Add the file include path for **water_leak** in **extra_lib/CMakeLists.txt**, as shown in Images 5.5 and 5.6. Its format is similar to that of **tem_hum** or **door**."

547

548

[[image:image-20241121181957-17.png||height="438" width="516"]]

549

550

image 5.5 extra_lib/CMakeLists.txt before add

551

552

[[image:image-20241121182239-18.png||height="520" width="518"]]

553

554

image 5.6 extra_lib/CMakeLists.txt after add

555

556

6. **Modify the header files included in the fonts and images directories**.

557

558

Open the **fonts/ui_font_Font12.c** file, as shown in Image 5.7, and change **#include "../ui.h"** to **#include "../ui_water_leak.h"**. The modified file is shown in Image 5.8. Other font files need to be modified in the same way.

559

560

[[image:image-20241121171629-11.png]]

561

562

image 5.7 before-modified font file

563

564

[[image:image-20241121171901-12.png]]

565

566

image 5.8 modified font file

567

568

Open the **images/ui_img_battery_empty_png.c** file, as shown in Image 5.9, and change **#include "../ui.h"** to **#include "../ui_water_leak.h"**. The modified file is shown in Image 5.10. Other image files need to be modified in the same way.

569

570

[[image:image-20241121172714-13.png]]

571

572

image 5.9 before-modified image file

573

574

[[image:image-20241121172908-14.png]]

575

576

image 5.10 modified image file

577

578

7. Modify the **ui_water_leak/CMakeLists.txt**. Open this file, and modify it as shown in image 5.11 (before) and image 5.12 (after).

579

580

[[image:image-20241121180030-15.png]]

581

582

image 5.11 ui_water_leak/CMakeLists.txt before modification

583

584

[[image:image-20241121180517-16.png]]

585

586

image 5.12 ui_water_leak/CMakeLists.txt after modification

587

588

589

8. Modify the **ui_water_leak.h** file. Images 5.13 and 5.14 show the code before modification, while Images 5.15 and 5.16 show the code after modification.

590

591

[[image:image-20241122094200-23.png]]

592

593

image 5.13 ui_water_leak.h (1) before modification

594

595

[[image:image-20241122094320-24.png||height="852" width="554"]]

596

597

image 5.14 ui_water_leak.h (2) before modification

598

599

[[image:image-20241122094600-25.png||height="1078" width="554"]]

600

601

image 5.15 ui_water_leak.h (1) after modification

602

603

[[image:image-20241122094719-26.png||height="941" width="583"]]

604

605

image 5.16 ui_water_leak.h (2) before modification

606

607

9. **Modify ui_water_leak.c file.** The image 5.17, 5.18, 5.19 show the code before modification, and the image 5.20, 5.21, 5.22 show the code after modification.

608

609

_ui_flag_modify( ((lv_obj_t *)(e->user_data)), LV_OBJ_FLAG_HIDDEN, _UI_MODIFY_FLAG_TOGGLE); This code replaces 4 lines of code in ui_water_leak.c, so it is pasted here for convenience.

610

611

[[image:image-20241122102929-27.png||height="619" width="426"]]

612

613

image 5.17 ui_water_leak.c (1) before modification

614

615

[[image:image-20241122112838-30.png||height="551" width="628"]]

616

617

image 5.18 ui_water_leak.c (2) before modification

618

619

[[image:image-20241122110815-29.png||height="725" width="712"]]

620

621

image 5.19 ui_water_leak.c (3) before modification

622

623

[[image:image-20241122113158-31.png||height="872" width="677"]]

624

625

image 5.20 ui_water_leak.c (1) after modification

626

627

[[image:image-20241122113259-33.png||height="874" width="724"]]

628

629

image 5.21 ui_water_leak.c (2) after modification

630

631

[[image:image-20241122113359-34.png||height="804" width="746"]]

632

633

image 5.22 ui_water_leak.c (3) after modification

634

635

10. **Modify ui_water_leak_events.h file.** The image 5.23 show the code before modification, and the image 5.24 show the code after modification.

636

637

[[image:image-20241122134113-35.png||height="380" width="421"]]

638

639

image 5.23 ui_water_leak_events_.h before modification

640

641

[[image:image-20241122134420-37.png||height="201" width="283"]]

642

643

image 5.24 ui_water_leak_events_.h after modification

644

645

11.** Modify ui_water_leak_events.c file.** The image 5.25 show the code before modification, and the image 5.26 show the code after modification.

646

647

Step1. '#include "ui.h"'~-~->'#include "ui_water_leak.h"'

648

649

Step2. add code below in delete_object() function definition.

650

651

panel_all * panel = find_upper_by_SensorPanel(&arr,((lv_obj_t *)(e->user_data~)~)~);

652

653

size_t index = panel->panel_obj_index;

654

655

deleteElement(&arr, index);

656

657

[[image:image-20241122135023-38.png||height="358" width="372"]]

658

659

image 5.25 ui_water_leak_events_.c before modification

660

661

[[image:image-20241122135258-39.png||height="403" width="559"]]

662

663

image 5.26 ui_water_leak_events_.c after modification

664

665

666

12. **Modify ui_water_leak_style.c file.**

667

668

Step1. '#include "../ui.h"'~-~->#include '"../ui_water_leak.h"'

669

670

add '#include "../../sort.h"'

671

672

add '#include "ui.h"'

673

674

[[image:image-20241122141536-41.png||height="361" width="612"]]

675

676

image 5.27 ui_water_leak_style.c (1) before modification

677

678

[[image:image-20241122142129-42.png||height="386" width="613"]]

679

680

image 5.28 ui_water_leak_style.c (1) after modification

681

682

683

Step2. modify 'void ui_ScreenMain_screen_init(void)'~-~->'panel_with_type create_water_leak(uint8_t index)'

684

685

delete code as shown in image 5.29

686

687

[[image:image-20241122145620-44.png||height="757" width="671"]]

688

689

image 5.29 ui_water_leak_style.c (2)

690

691

692

Step3. The image 5.30, 5.31 show the change.

693

694

[[image:image-20241122152026-45.png||height="277" width="828"]]

695

696

image 5.30 ui_water_leak_style.c (3) before modification

697

698

[[image:image-20241122152542-46.png||height="293" width="830"]]

699

700

image 5.31 ui_water_leak_style.c (3) after modification

701

702

703

Step4. Copy partly the code in ui_water_leak.c, paste at extra_lib/sort.h(The process is shown in image 5.32, 5.33).

704

705

[[image:image-20241122153958-47.png]]

706

707

image 5.32 ui_water_leak_style.c (4)

708

709

710

[[image:image-20241122154755-49.png||height="864" width="513"]]

711

712

image 5.33 ui_water_leak_style.c (4)

713

714

715

Step5. Delete event function in code which was just pasted in extra_lib/sort.h(The process is shown in image 5.34).

716

717

[[image:image-20241122155650-50.png||height="922" width="513"]]

718

719

image 5.34 ui_water_leak_style.c (5)

720

721

722

Step6. Add some lines of code in extra_lib/sort.h as shown in image 5.35.

723

724

[[image:image-20241122161934-51.png]]

image 5.35

Step7. Add a line of code in extra_lib/sort.h as shown in image 5.36.

730

731

[[image:image-20241122162852-53.png||height="330" width="529"]]

image 5.37

Step8. Add some code in ui_water_leak_style.c as shown in image 5.38 from line534 to line 576 in detail.

737

738

panel_with_type union_sensor;

739

740

union_sensor.panel_type = WATER_LEAK_TYPE;

......

lv_obj_set_x(union_sensor.panel_union.door.ui_PanelSensorDoor, x_by_index(index));

745

746

lv_obj_set_y(union_sensor.panel_union.door.ui_PanelSensorDoor, y_by_index(index));

return union_sensor;

[[image:image-20250122173546-6.png||height="777" width="922"]]

image 5.38

13. Rest midification in sort.h file.

756

757

In image 5.39 as below, we can see "WATER_LEAK_TYPE" at line 24 and water leak switch status definition at line 32,33, and these are what we need to add in sort.h.

758

759

[[image:image-20250122170230-1.png||height="580" width="513"]]

image 5.39 sort.h

13. **Modify sort.c file.**

764

765

Add a line of code ~-~-'#include "ui_water_leak.h"' as shown in image 5.39 line 26.

766

767

[[image:image-20250122171910-5.png||height="524" width="510"]]

768

769

image 5.40 sort.c (1)

770

771

There are still some changes need to be done in sort.c, and omit here for the moment.

= 6. FAQ =

== 6.1 ==

= 7. Order Info =

== 7.1 Part Number ==

783

784

785

Part Number: (% style="color:#4472c4" %)LTS5

786

787

788

== 7.2 Packing Info ==

789

790

791

**Package Includes**:

792

793

* LTS5 HMI Touch Screen

794

* 5V,2A DC Power Adapter.

795

* USB Type C Program Cable

= 8. Support =

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

801

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]].

802

803

= 9. Reference material =

* Datasheet

* Source Code: [[dragino/LoRa-HMI-Touch-Screen: Open Source LoRa / LoRaWAN HMI Touch Screen Project>>url:https://github.com/dragino/LoRa-HMI-Touch-Screen/tree/main]]

* Mechinical

= 10. FCC Warning =

This device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:

814

815

(1) This device may not cause harmful interference;