Last modified by Dilisi S on 2025/02/26 19:24
<
From version < 4.4 >
edited by Edwin Chen
on 2024/09/16 08:43
To version < 56.1 >
edited by Xiaoling
on 2024/10/18 16:13
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Edwin
1 +XWiki.Xiaoling
Content
... ... @@ -1,9 +1,14 @@
1 -
1 +(% style="text-align:center" %)
2 2  [[image:image-20240915231842-1.png]]
3 3  
4 4  
5 +
6 +
7 +
8 +
9 +
5 5  (% _mstvisible="1" %)
6 -(% _msthash="315238" _msttexthash="18964465" _mstvisible="3" %)**Table of Contents：**
11 +(% _msthash="315238" _msttexthash="18964465" _mstvisible="3" %)**Table of Contents:**
7 7  
8 8  {{toc/}}
9 9  
... ... @@ -18,6 +18,7 @@
18 18  
19 19  == 1.1  What is LTS5 LoRa HMI touch screen ==
20 20  
26 +
21 21  LTS5 is a (% style="color:blue" %)LoRa / LoRaWAN HMI Touch Screen(%%) designed for display purpose of IoT project. It have a 5.0" HMI touch screen, and support WiFi, Bluetooch, LoRa wireless protocol.
22 22  
23 23  LTS5 is an Open Source software project. The MCU is ESP32 and Dragino LA66 LoRa module. There are lots of development source for ESP32 which can greatly reduce the development time.
... ... @@ -29,9 +29,12 @@
29 29  
30 30  == 1.2  Features ==
31 31  
38 +* ESP32-WROOM MCU: 8MB RAM & 16MB ROM
39 +* Dragino LA66 LoRa Module
32 32  * Support Private LoRa protocol or LoRaWAN protocol
33 33  * Support WiFi & BLE wireless protocol
34 34  * 5.0" HMI touch screen
43 +* Support LVGL case. SquareLine program.
35 35  * Support RS485 Interface
36 36  * Open Source Project
37 37  * Wall Attachable.
... ... @@ -41,24 +41,49 @@
41 41  
42 42  == 1.3  Specification ==
43 43  
44 -**Display:**
45 45  
46 -* Resolution: 0.01 °C
47 -* Accuracy Tolerance: Typ ±0.2 °C
48 -* Long Term Drift: < 0.03 °C/yr
49 -* Operating Range: -10 ~~ 50 °C  or -40 ~~ 60 °C (depends on battery type, see [[FAQ>>||anchor="H6.5Whyiseedifferentworkingtemperatureforthedevice3F"]])
54 +**LoRa**:
50 50  
51 -
56 +* Frequency Range: 870 MHz ~~ 960 MHz
57 +* TCXO crystal to ensure RF performance on low temperature
58 +* Maximum Power +22 dBm constant RF output
59 +* High sensitivity: -148 dBm
60 +* LoRa Tx Current: <90 mA at +17 dBm, 108 mA at +22 dBm
61 +* LoRa Rx current: <9 mA
52 52  
63 +**WiFi:**
64 +
65 +* 802.11b/g/n
66 +* Up to 150 Mbps data rate in 802.11n mode
67 +* Support A-MPDU and A-MSDU aggregation
68 +* zero point four μ S protection interval
69 +* Working channel center frequency range: 2412~~2484 MHz
70 +
71 +**Bluetooth:**
72 +
73 +* Bluetooth V4.2 BR/EDR and Bluetooth LE standard
74 +* Class-1, Class-2, and Class-3 transmitters.
75 +* AFH
76 +* CVSD and SBC
77 +
78 +**Display:**
79 +
80 +* 5.0 Inch , 800 x 480
81 +* IPS Capacitive Touch SCreen
82 +* RGB color.
83 +* Display Area: 120.7*75.80 mm
84 +
53 53  == 1.4  Power Consumption ==
54 54  
55 -* External 5V DC power.
56 56  
88 +* External 5V DC power adapter
57 57  
90 +
58 58  == 1.5  Storage & Operation Temperature ==
59 59  
60 60  
61 --10 ~~ 50 °C  or -40 ~~ 60 °C (depends on battery type, see [[FAQ>>||anchor="H6.5Whyiseedifferentworkingtemperatureforthedevice3F"]])
94 +* Operation Temperature: -20 ~~ 70°C  (No Dew)
95 +* Storage Temperature: -30 ~~ 70°C  (No Dew)
62 62  
63 63  
64 64  == 1.6  Applications ==
... ... @@ -72,1022 +72,212 @@
72 72  * Smart Factory
73 73  
74 74  
75 -= 2.  Operation Mode =
109 += 2.  Getting Started with Hello World =
76 76  
77 -== 2.1  How it work? ==
111 +== 2.1  About this demo ==
78 78  
79 79  
80 -Each PB01 is shipped with a worldwide unique set of LoRaWAN OTAA keys. To use PB01 in a LoRaWAN network, user needs to input the OTAA keys in LoRaWAN network server. After this, if PB01 is under this LoRaWAN network coverage, PB01 can join the LoRaWAN network and start to transmit sensor data. The default period for each uplink is** 20 minutes**.
114 +In this Getting Started Example, we will show how to design a simple Display UI and upload it to LTS5. This UI has  a button , when user click the button. The Web UI will jump to a new page.
81 81  
82 82  
83 -== 2.2  How to Activate PB01? ==
117 +== 2.2  Install Software Running Environment ==
84 84  
119 +The ESP MCU can be developed using ESP-IDF, Arduino, or MicroPython. For this project, we utilize ESP-IDF for compilation and Visual Studio Code (VSCode) for editing.
85 85  
86 -(% style="color:red" %)** 1.  Open enclosure from below position.**
121 +=== 2.2.1 Install VSCode and ESP-IDF extension ===
87 87  
88 -[[image:image-20220621093835-1.png]]
89 89  
124 +Firstly, download and install VSCode for your computer's operating system from the official website: [[Download Visual Studio Code - Mac, Linux, Windows>>url:https://code.visualstudio.com/download]].
90 90  
91 -(% style="color:red" %)** 2.  Insert 2 x AAA LR03 batteries and the node is activated.**
126 +Next, you need to install the ESP-IDF extension within VSCode. The detailed operation steps are illustrated in image 1.
92 92  
93 -[[image:image-20220621093835-2.png]]
128 +[[image:image-20240928110211-5.png||height="508" width="866"]]
94 94  
130 + image 1 ESP-IDF extension install
95 95  
96 -(% style="color:red" %)** 3. Under the above conditions, users can also reactivate the node by long pressing the ACT button.**
132 +Links for reference: [[Install ESP32 ESP-IDF on Windows and Integrate with VS code (esp32tutorials.com)>>url:https://esp32tutorials.com/install-esp32-esp-idf-windows-integrate-vs-code/#:~~:text=In%20this%20tutorial,%20we%20will%20show%20you%20how%20to%20install]]
97 97  
98 -[[image:image-20220621093835-3.png]]
99 99  
135 +=== 2.2.2 Install SquareLine Studio ===
100 100  
101 -User can check [[LED Status>>||anchor="H2.8LEDIndicator"]] to know the working state of PB01.
102 102  
138 +The version we are utilizing for this software is 1.4.2. You can download it from the official link: [[SquareLine Studio - Download the current version of SquareLine Studio>>url:https://squareline.io/downloads#lastRelease]].
103 103  
104 -== 2.3  Example to join LoRaWAN network ==
140 +Please note that this software necessitates the registration of a license prior to usage, and various licenses come with distinct limitations. For instance, the free version imposes restrictions such as a limit of 1 component, 150 widgets, and 10 screens. However, for first-time downloads, you are granted unrestricted access for a period of 30 days without the need for immediate registration.
105 105  
106 106  
107 -This section shows an example for how to join the [[TheThingsNetwork>>url:https://www.thethingsnetwork.org/]] LoRaWAN IoT server. Usages with other LoRaWAN IoT servers are of similar procedure.
143 +== 2.3 Simple usage of SquareLine Studio and export UI code ==
108 108  
109 -(% _mstvisible="1" class="wikigeneratedid" %)
110 -Assume the LPS8v2 is already set to connect to [[TTN V3 network >>url:https://eu1.cloud.thethings.network/]]. We need to add the PB01 device in TTN V3 portal. 
111 111  
112 -[[image:image-20240705094824-4.png]]
146 +After launching and logging in to this software, create a project as shown in the following image 2. The version of LVGL is 8.3.11.
113 113  
114 -(% style="color:blue" %)**Step 1**(%%):  Create a device in TTN V3 with the OTAA keys from PB01.
148 +[[image:image-20240928103357-2.png||height="680" width="708"]]
115 115  
116 -Each PB01 is shipped with a sticker with the default DEV EUI as below:
150 + image 2 create a SquareLine project
117 117  
118 -[[image:image-20230426083617-1.png||height="294" width="633"]]
152 +Next, we need to make some settings for this project. By clicking in the specified order on image 3, we can see the page as shown in image 4.
119 119  
154 +[[image:1727229582471-566.png]]
120 120  
121 -Enter these keys in the LoRaWAN Server portal. Below is TTN V3 screen shot:
156 + image 3 project settings
122 122  
123 -Create application.
158 +[[image:image-20240928105309-4.png||height="526" width="556"]]
124 124  
125 -choose to create the device manually.
160 + image 4 modify project settings
126 126  
127 -Add JoinEUI(AppEUI), DevEUI, AppKey.(% style="display:none" %)
162 +Now we can start to use this software. Here are some usage information for this software.
128 128  
129 -[[image:image-20240507142116-1.png||height="410" width="1138"]](% style="display:none" %) (%%)
130 -
164 +**~1. add widget**
131 131  
132 -[[image:image-20240507142157-2.png||height="559" width="1147"]]
166 +To add a widget, you should click a widget you want to add at the area entitled “Widgets”. In image , demonstrate a add process of label, button, and image 5.
133 133  
134 -[[image:image-20240507142401-3.png||height="693" width="1202"]]
168 +[[image:image-20240928111412-6.png||height="526" width="864"]]
135 135  
136 -[[image:image-20240507142651-4.png||height="760" width="1190"]]
170 + image 5 add widgets
137 137  
138 -**Default mode OTAA**(% style="display:none" %)
172 +**2. modify widget**
139 139  
174 +The area for modifying widgets is called "Inspector". There are four parts in the "Inspector" tab. We use three of them more frequently, excluding "COMPONENT". The second part is aimed at adjusting the layout, size, position, alignment, flags, and states, etc. of widgets. The name of the second part indicates the type of widget it is representing, and in image 6, it is "BUTTON".
140 140  
141 -(% style="color:blue" %)**Step 2**(%%):  Use ACT button to activate PB01 and it will auto join to the TTN V3 network. After join success, it will start to upload sensor data to TTN V3 and user can see in the panel.
176 +[[image:1727485118799-984.png]]
142 142  
143 -[[image:image-20240507143104-5.png||height="434" width="1398"]]
178 + image 6 the button widget's "Inspector" tab
144 144  
180 +Second part: "Layout" means a auto position-management for widgets contained in the parent widget. "Transform" includes size, position and align modification.
145 145  
146 -== 2.4  Uplink Payload ==
182 +[[image:1727485251053-655.png]]
147 147  
184 +image 7 the button widget's "BUTTON" tab
148 148  
149 -Uplink payloads include two types: Valid Sensor Value and other status / control command.
186 +Third part: It is an area of style setting.
150 150  
151 -* Valid Sensor Value: Use FPORT=2
152 -* Other control command: Use FPORT other than 2.
188 +Fourth part: It is an area for adding events. In image 8, it is adding a click event to a button. If the button is clicked after the click event is added as shown in image 8, the current screen will fade into another specified screen, and the switching process will last 500ms.
153 153  
154 -=== 2.4.1  Uplink FPORT~=5, Device Status ===
190 +[[image:1727485480434-713.png||height="395" width="290"]]
155 155  
192 + image 8 add event for button
156 156  
157 -Users can  get the Device Status uplink through the downlink command:
194 +**3. change label widget content**
158 158  
159 -(% style="color:#4472c4" %)**Downlink:  **(%%)**0x2601**
196 +Modify the content in text as shown in image 9, the text content of label widget will be changed accordingly.
160 160  
161 -Uplink the device configures with FPORT=5.
198 +[[image:image-20240928090825-1.png||height="327" width="391"]]
162 162  
163 -(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:370px" %)
164 -|=(% style="width: 60px;background-color:#4F81BD;color:white" %)**Size(bytes)(% style="display:none" %) (%%)**|=(% style="width: 60px;background-color:#4F81BD;color:white" %)**1**|=(% style="width: 80px;background-color:#4F81BD;color:white" %)**2**|=(% style="width: 80px;background-color:#4F81BD;color:white" %)**1**|=(% style="width: 60px;background-color:#4F81BD;color:white" %)**1**|=(% style="width: 30px;background-color:#4F81BD;color:white" %)**2**
165 -|(% style="width:99px" %)Value|(% style="width:62px" %)Sensor Model|(% style="width:80px" %)Firmware Version|(% style="width:82px" %)Frequency Band|(% style="width:85px" %)Sub-band|(% style="width:46px" %)BAT
200 + image 9 modify text content of label widget
166 166  
167 -[[image:image-20240507152130-12.png||height="469" width="1366"]](% style="display:none" %)
202 +**4. Add image into project**
168 168  
169 -Example Payload (FPort=5):  [[image:image-20240507152254-13.png||height="26" width="130"]]
204 +To use the image widget, you should first add an image to your project. The image format must be PNG, and its resolution should not exceed 800x480 pixels. There are two ways to add an image file. One way is to move your image into the folder "…/squareline project/assets/", as shown in image 10. The other way is to click the "ADD FILE INTO ASSETS" button, then select an image from your computer to import. After adding, you can see the image in the "assets" area in SquareLine Studio, as demonstrated in image 11.
170 170  
206 +[[image:image-20240928113424-9.png||height="355" width="505"]]
171 171  
172 -(% style="color:#4472c4" %)**Sensor Model**(%%): For PB01, this value is 0x35.
208 + image 10 add image file into SquareLine Studio project
173 173  
174 -(% style="color:#4472c4" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version.
210 +[[image:image-20240928114139-10.png||height="559" width="810"]]
175 175  
176 -(% style="color:#4472c4" %)**Frequency Band**:
212 + image 11 use image widget in SquareLine Studio
177 177  
178 -*0x01: EU868
214 +**5. The relationship between widgets**
179 179  
180 -*0x02: US915
216 +There are two common relationships between widgets: one is parallel, the other is parent-child. The parallel relationship means that widgets' relative position is based on a collective object of reference. In parent-child relationship, the parts of the child object that are outside the boundaries of the parent object are not visible by default. Therefore, we need to adjust the position of the child object so that it falls within the range of the parent object, allowing it to be seen as illustrated in image 13.
181 181  
182 -*0x03: IN865
218 +[[image:1727486567182-334.png||height="318" width="278"]]
183 183  
184 -*0x04: AU915
220 +image 12 move label1 to make label1 widget be a child of button1 widget(1)
185 185  
186 -*0x05: KZ865
222 +[[image:image-20240928112001-8.png||height="431" width="796"]]
187 187  
188 -*0x06: RU864
224 + image 13 move label1 to make label1 widget be a child of button1 widget(2)
189 189  
190 -*0x07: AS923
226 +**6. Preview the final effect**
191 191  
192 -*0x08: AS923-1
228 +An advantage of this kind of software is that you can edit the UI with quick previews. In other words, it provides a way of combining graphical programming with simulation immediately.
193 193  
194 -*0x09: AS923-2
230 +[[image:1727487368023-281.png]]
195 195  
196 -*0x0a: AS923-3
232 + image 14 click on the triangle icon to start or end the simulation
197 197  
234 +For more detailed usage, please visit the official link: [[SquareLine Studio 1.4.2 Documentation ~| SquareLine Studio>>url:https://docs.squareline.io/docs/squareline/]].
198 198  
199 -(% style="color:#4472c4" %)**Sub-Band**(%%): value 0x00 ~~ 0x08(only for CN470, AU915,US915. Others are0x00)
200 200  
201 -(% style="color:#4472c4" %)**BAT**(%%): shows the battery voltage for PB01.
237 +== 2.4 Integrate UI Code to ESP-IDF Project ==
202 202  
203 -(% style="color:#4472c4" %)**Ex1**(%%): 0x0C DE = 3294mV
204 204  
240 +To achieve the integrating, we first need to export the UI code, then make some modifications, and finally relocate the UI code to a specific position within the project.
205 205  
206 -=== 2.4.2  Uplink FPORT~=2, Real time sensor value ===
242 +[[image:1727229798126-306.png]]
207 207  
244 + image 15 export UI file
208 208  
209 -PB01 will send this uplink after Device Status uplink once join LoRaWAN network successfully. And it will periodically send this uplink. Default interval is 20 minutes and [[can be changed>>||anchor="H3.1A0DownlinkCommandSet"]].
246 +[[image:1727229821582-258.png||height="333" width="662"]]
210 210  
211 -Uplink uses FPORT=2 and every 20 minutes send one uplink by default.
248 + image 16 exported UI file
212 212  
213 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:460px" %)
214 -|=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
215 -**Size(bytes)**
216 -)))|=(% style="width: 60px;background-color:#4F81BD;color:white" %)2|=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
217 -**1**
218 -)))|=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
219 -**1**
220 -)))|=(% style="width: 90px;background-color:#4F81BD;color:white" %)(((
221 -**2**
222 -)))|=(% style="width: 40px;background-color:#4F81BD;color:white" %)(((
223 -**2**
224 -)))
225 -|(% style="width:97px" %)(((
226 -Value
227 -)))|(% style="width:39px" %)Battery|(% style="width:39px" %)(((
228 -Sound_ACK
250 +Create a empty directory entitled "ui" in path "basic_prj/app_components/ui/", and then copy all UI code exported to this directory.
229 229  
230 -&Sound_key
231 -)))|(% style="width:100px" %)(((
232 -(((
233 -Alarm
234 -)))
235 -)))|(% style="width:77px" %)(((
236 -(((
237 -Temperature
238 -)))
239 -)))|(% style="width:47px" %)(((
240 -Humidity
241 -)))
252 +[[image:image-20240928144830-11.png]]
242 242  
243 -Example in TTN.
254 + image 17 open CMakeLists.txt
244 244  
245 -[[image:image-20240507150155-11.png||height="549" width="1261"]]
256 +[[image:1727229892636-154.png||height="521" width="407"]]
246 246  
247 -Example Payload (FPort=2):  (% style="background-color:yellow" %)**0C EA 03 01 01 11 02 A8**
258 + image 18 modify CMakeLists.txt
248 248  
249 -==== (% style="color:blue" %)**Battery:**(%%) ====
260 +The last step of integrating is adding two lines of code in main.c file.
250 250  
251 -Check the battery voltage.
262 +[[image:1727229926561-300.png]]
252 252  
253 -* Ex1: 0x0CEA = 3306mV
254 -* Ex2: 0x0D08 = 3336mV
264 + image 19 add "ui.h"
255 255  
256 -==== (% style="color:blue" %)**Sound_ACK & Sound_key:**(%%) ====
266 +[[image:1727229955611-607.png]]
257 257  
258 -Key sound and ACK sound are enabled by default.
268 + image 20 add "ui_init()"
259 259  
260 -* Example1: 0x03
261 261  
262 - Sound_ACK: (03>>1) & 0x01=1, OPEN.
271 +== 2.5 Brief introduction of hello world project ==
263 263  
264 -**~ ** Sound_key:  03 & 0x01=1, OPEN.
265 265  
266 -* Example2: 0x01
274 +The project consists of two screens. The first screen displays the company's logo, the project name, and a button to navigate to the next screen. The second screen presents some information about this HMI screen product through an image and includes a button to return to the previous screen.
267 267  
268 - Sound_ACK: (01>>1) & 0x01=0, CLOSE.
269 269  
270 -**~ ** Sound_key:  01 & 0x01=1, OPEN.
277 +== 2.6 Test Result ==
271 271  
272 272  
273 -==== (% style="color:blue" %)**Alarm:**(%%) ====
280 +By pressing the button lying bottom right, the screen can switch to another as expected. This indicates that the UI file has been successfully integrated into the project and is now effective.
274 274  
275 -Key alarm.
282 +[[image:1727488067077-684.png||height="402" width="574"]]
276 276  
277 -* Ex1: 0x01 & 0x01=1, TRUE.
278 -* Ex2: 0x00 & 0x01=0, FALSE.
284 + image 21 screen1
279 279  
280 -==== (% style="color:blue" %)**Temperature:**(%%) ====
286 +[[image:1727488157579-949.png||height="397" width="572"]]
281 281  
282 -* Example1:  0x0111/10=27.3℃
283 -* Example2:  (0xFF0D-65536)/10=-24.3℃
288 + image 22 screen2
284 284  
285 -If payload is: FF0D :  (FF0D & 8000 == 1) , temp = (FF0D - 65536)/100 =-24.3℃
286 286  
287 -（FF0D & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）
291 += 3. Example Project 1: LoRa Central Display =
288 288  
293 +[[image:image-20240916101737-1.png||height="468" width="683"]]
289 289  
290 -==== (% style="color:blue" %)**Humidity:**(%%) ====
291 291  
292 -* Humidity:    0x02A8/10=68.0%
296 += 4. Example Project 2: LoRaWAN RS485 Alarm =
293 293  
294 -=== 2.4.3  Uplink FPORT~=3, Datalog sensor value ===
295 295  
296 -
297 -PB01 stores sensor value and user can retrieve these history value via downlink command. The Datalog sensor value are sent via FPORT=3.
298 -
299 -[[image:image-20240510144912-1.png||height="471" width="1178"]](% style="display:none" %)
300 -
301 -
302 -* Each data entry is 11 bytes, to save airtime and battery, PB01 will send max bytes according to the current DR and Frequency bands.(% style="display:none" %)
303 -
304 -For example, in US915 band, the max payload for different DR is:
305 -
306 -1. **DR0**: max is 11 bytes so one entry of data
307 -1. **DR1**: max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
308 -1. **DR2**: total payload includes 11 entries of data
309 -1. **DR3**: total payload includes 22 entries of data.
310 -
311 -(% style="color:red" %)**Notice: PB01 will save 178 set of history data, If device doesn't have any data in the polling time. Device will uplink 11 bytes of 0.**
312 -
313 -See more info about the [[Datalog feature>>||anchor="H2.6A0DatalogFeature"]].
314 -
315 -(% style="display:none" %) (%%)
316 -
317 -=== 2.4.4  Decoder in TTN V3 ===
318 -
319 -
320 -In LoRaWAN protocol, the uplink payload is HEX format, user need to add a payload formatter/decoder in LoRaWAN Server to get human friendly string.
321 -
322 -In TTN , add formatter as below:
323 -
324 -[[image:image-20240507162814-16.png||height="778" width="1135"]]
325 -
326 -(((
327 -Please check the decoder from this link:  [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>https://github.com/dragino/dragino-end-node-decoder]]
328 -)))
329 -
330 -(((
331 -
332 -)))
333 -
334 -== 2.5 Show data on Datacake ==
335 -
336 -
337 -(((
338 -Datacake IoT platform provides a human friendly interface to show the sensor data in charts, once we have sensor data in TTN V3, we can use Datacake to connect to TTN V3 and see the data in Datacake. Below are the steps:
339 -)))
340 -
341 -(((
342 -
343 -)))
344 -
345 -(((
346 -(% style="color:blue" %)**Step 1**(%%):  Be sure that your device is programmed and properly connected to the LoRaWAN network.
347 -)))
348 -
349 -(((
350 -(% style="color:blue" %)**Step 2**(%%):  Configure your Application to forward data to Datacake you will need to add integration. Go to TTN V3 Console ~-~-> Applications ~-~-> Integrations ~-~-> Add Integrations.
351 -)))
352 -
353 -(((
354 -~1. Add Datacake:
355 -)))
356 -
357 -(((
358 -2. Select default key as Access Key:
359 -)))
360 -
361 -(((
362 -3. In Datacake console ([[https:~~/~~/datacake.co/>>url:https://datacake.co/]]) , add PB01:
363 -)))
364 -
365 -(((
366 - Please refer to the figure below.
367 -)))
368 -
369 -[[image:image-20240510150924-2.png||height="612" width="1186"]]
370 -
371 -
372 -Log in to DATACAKE, copy the API under the account.
373 -
374 -[[image:image-20240510151944-3.png||height="581" width="1191"]]
375 -
376 -
377 -
378 -[[image:image-20240510152150-4.png||height="697" width="1188"]]
379 -
380 -
381 -[[image:image-20240510152300-5.png||height="298" width="1191"]]
382 -
383 -
384 -[[image:image-20240510152355-6.png||height="782" width="1193"]]
385 -
386 -[[image:image-20240510152542-8.png||height="545" width="739"]]
387 -
388 -[[image:image-20240510152634-9.png||height="748" width="740"]]
389 -
390 -
391 -[[image:image-20240510152809-10.png||height="607" width="732"]]
392 -
393 -[[image:image-20240510153934-14.png||height="460" width="1199"]]
394 -
395 -
396 -[[image:image-20240510153435-12.png||height="428" width="1197"]]
397 -
398 -
399 -Copy and paste the [[TTN decoder>>https://github.com/dragino/dragino-end-node-decoder]] here and save.
400 -
401 -[[image:image-20240510153624-13.png||height="468" width="1195"]]
402 -
403 -
404 -Visual widgets please read the DATACAKE documentation.
405 -
406 -(% style="display:none" %) (%%)
407 -
408 -== 2.6  Datalog Feature ==
409 -
410 -
411 -(% _msthash="315262" _msttexthash="32283004" _mstvisible="1" %)
412 -When user want to retrieve sensor value, he can send a poll command from the IoT platform to ask sensor to send value in the required time slot.
413 -
414 -
415 -=== 2.6.1  Unix TimeStamp ===
416 -
417 -
418 -Unix TimeStamp shows the sampling time of uplink payload. format base on
419 -
420 -[[image:image-20220523001219-11.png||_mstalt="450450" _mstvisible="3" height="97" width="627"]]
421 -
422 -User can get this time from link:  [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/||_mstvisible="3"]] :
423 -
424 -For example: if the Unix Timestamp we got is hex 0x60137afd, we can convert it to Decimal: 1611889405. and then convert to the time: 2021 – Jan ~-~- 29 Friday 03:03:25 (GMT)
425 -
426 -
427 -[[image:1655782409139-256.png]]
428 -
429 -
430 -=== 2.6.2  Poll sensor value ===
431 -
432 -
433 -(((
434 -User can poll sensor value based on timestamps from the server. Below is the downlink command.
435 -)))
436 -
437 -(((
438 -Timestamp start and Timestamp end use Unix TimeStamp format as mentioned above. Devices will reply with all data log during this time period, use the uplink interval.
439 -)))
440 -
441 -(((
442 -For example, downlink command [[image:image-20220621113526-13.png]] (% _mstvisible="3" style="display:none" %)
443 -)))
444 -
445 -(((
446 -Is to check 2020/12/1 07:40:00 to 2020/12/1 08:40:00's data
447 -)))
448 -
449 -(((
450 -Uplink Internal =5s，means PB01 will send one packet every 5s. range 5~~255s.
451 -)))
452 -
453 -
454 -=== 2.6.3  Datalog Uplink payload ===
455 -
456 -
457 -See [[Uplink FPORT=3, Datalog sensor value>>||anchor="H2.4.3A0UplinkFPORT3D32CDatalogsensorvalue"]]
458 -
459 -(% style="display:none" %) (%%) (% style="display:none" %)
460 -
461 -== 2.7 Button ==
462 -
463 -
464 -* ACT button
465 -
466 -Long press this button PB01 will reset and join network again.
467 -
468 -[[image:image-20240510161626-17.png||height="192" width="224"]]
469 -
470 -* Alarm button
471 -
472 -Press the button PB01 will immediately uplink data, and alarm is "TRUE".
473 -
474 -[[image:image-20240705095149-5.png||height="164" width="162"]](% style="display:none" %)
475 -
476 -
477 -== 2.8 LED Indicator ==
478 -
479 -
480 -(((
481 -The PB01 has a triple color LED which for easy showing different stage.
482 -)))
483 -
484 -Hold the ACT green light to rest, then the green flashing node restarts, the blue flashing once upon request for network access, and the green constant light for 5 seconds after successful network access
485 -
486 -(((
487 -(% style="color:#037691" %)**In a normal working state**:
488 -)))
489 -
490 -* When the node is restarted, hold the ACT (% style="color:green" %)**GREEN**(%%) lights up , then the (% style="color:green" %)**GREEN**(%%) flashing node restarts.The (% style="color:blue" %)**BLUE**(%%) flashing once upon request for network access, and the (% style="color:green" %)**GREEN**(%%) constant light for 5 seconds after successful network access(% style="color:#0000ff" %)**.**
491 -* During OTAA Join:
492 -** **For each Join Request uplink:** the (% style="color:green" %)**GREEN LED** (%%)will blink once.
493 -** **Once Join Successful:** the (% style="color:green" %)**GREEN LED**(%%) will be solid on for 5 seconds.
494 -* After joined, for each uplink, the (% style="color:blue" %)**BLUE LED**(%%) or (% style="color:green" %)**GREEN LED** (%%)will blink once.
495 -* Press the alarm button，The (% style="color:red" %)**RED**(%%) flashes until the node receives the ACK from the platform and the (% style="color:blue" %)**BLUE**(%%) light stays 5s.
496 -
497 -(((
498 -
499 -)))
500 -
501 -== 2.9 Buzzer ==
502 -
503 -
504 -The PB01 has** button sound** and** ACK sound** and users can turn on or off both sounds by using [[AT+SOUND>>||anchor="H3.3A0Setbuttonsoundandbuttonalarm"]].
505 -
506 -* (% style="color:#4f81bd" %)**Button sound**(%%)** **is the music produced by the node after the alarm button is pressed.
507 -
508 - Users can use[[ AT+OPTION>>||anchor="H3.4A0Setbuzzermusic2807E429"]] to set different button sounds.
509 -
510 -* (% style="color:#4f81bd" %)**ACK sound **(%%)is the notification tone that the node receives ACK.
511 -
512 -= 3.  Configure PB01 via AT command or LoRaWAN downlink =
513 -
514 -
515 -Users can configure PB01 via AT Command or LoRaWAN Downlink.
516 -
517 -* AT Command Connection: See [[FAQ>>||anchor="H6.FAQ"]].
518 -
519 -* LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>doc:Main.WebHome]]
520 -
521 -There are two kinds of commands to configure PB01, they are:
522 -
523 -* (% style="color:#4f81bd" %)**General Commands:**
524 -
525 -These commands are to configure:
526 -
527 -* General system settings like: uplink interval.
528 -
529 -* LoRaWAN protocol & radio-related commands.
530 -
531 -They are the same for all Dragino Devices which supports DLWS-005 LoRaWAN Stack(Note~*~*). These commands can be found on the wiki: [[End Device Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
532 -
533 -
534 -* (% style="color:#4f81bd" %)**Commands special design for PB01**
535 -
536 -These commands are only valid for PB01, as below:
537 -
538 -(% style="display:none" %) (%%)
539 -
540 -== 3.1  Downlink Command Set ==
541 -
542 -
543 -(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:500px" %)
544 -|=(% style="width: 130px; background-color: rgb(79, 129, 189); color: white;" %)**Command Example**|=(% style="width: 151px; background-color: rgb(79, 129, 189); color: white;" %)**Function**|=(% style="width: 92px; background-color: rgb(79, 129, 189); color: white;" %)**Response**|=(% style="width: 206px; background-color: rgb(79, 129, 189); color: white;" %)**Downlink**
545 -|(% style="width:130px" %)AT+TDC=?|(% style="width:151px" %)(((
546 -
547 -
548 -View current TDC time
549 -)))|(% style="width:92px" %)(((
550 -1200000
551 -OK
552 -)))|(% style="width:206px" %)Default 1200000(ms)
553 -|(% style="width:130px" %)AT+TDC=300000|(% style="width:151px" %)Set TDC time|(% style="width:92px" %)OK|(% style="width:206px" %)(((
554 -(((
555 -0X0100012C:
556 -01: fixed command
557 -00012C: 0X00012C=
558 -
559 -300(seconds)
560 -)))
561 -
562 -(((
563 -
564 -)))
565 -)))
566 -|(% style="width:130px" %)ATZ|(% style="width:151px" %)Reset node|(% style="width:92px" %) |(% style="width:206px" %)0x04FF
567 -|(% style="width:130px" %)AT+FDR|(% style="width:151px" %)Restore factory settings|(% style="width:92px" %) |(% style="width:206px" %)0X04FE
568 -|(% style="width:130px" %)AT+CFM=?|(% style="width:151px" %)View the current confirmation mode status|(% style="width:92px" %)(((
569 -0,7,0
570 -
571 -OK
572 -)))|(% style="width:206px" %)Default 0,7,0
573 -|(% style="width:130px" %)AT+CFM=1,7,1|(% style="width:151px" %)(((
574 -Confirmed uplink mode, the maximum number of retries is seven, and uplink fcnt increase by 1 for each retry
575 -)))|(% style="width:92px" %)(((
576 -OK
577 -)))|(% style="width:206px" %)(((
578 -05010701
579 -
580 -05: fixed command
581 -
582 -01:confirmed uplink
583 -
584 -07: retry 7 times
585 -
586 -01: fcnt count plus 1
587 -)))
588 -|(% style="width:130px" %)AT+NJM=?|(% style="width:151px" %)(((
589 -Check the current network connection method
590 -)))|(% style="width:92px" %)(((
591 -1
592 -OK
593 -)))|(% style="width:206px" %)Default 1
594 -|(% style="width:130px" %)AT+NJM=0|(% style="width:151px" %)Change the network connection method to ABP|(% style="width:92px" %)(((
595 -Attention:Take effect after ATZ
596 -OK
597 -)))|(% style="width:206px" %)(((
598 -0X2000: ABP
599 -0x2001: OTAA
600 -20: fixed command
601 -)))
602 -|(% style="width:130px" %)AT+RPL=?|(% style="width:151px" %)View current RPL settings|(% style="width:92px" %)(((
603 -0
604 -OK
605 -)))|(% style="width:206px" %)Default 0
606 -|(% style="width:130px" %)AT+RPL=1|(% style="width:151px" %)set RPL=1    |(% style="width:92px" %)OK|(% style="width:206px" %)(((
607 -0x2101:
608 -21: fixed command
609 -01: for details, check wiki
610 -)))
611 -|(% style="width:130px" %)AT+ADR=?|(% style="width:151px" %)View current ADR status|(% style="width:92px" %)(((
612 -1
613 -OK
614 -)))|(% style="width:206px" %)Default 0
615 -|(% style="width:130px" %)AT+ADR=0|(% style="width:151px" %)Set the ADR state to off|(% style="width:92px" %)OK|(% style="width:206px" %)(((
616 -0x2200: close
617 -0x2201: open
618 -22: fixed command
619 -)))
620 -|(% style="width:130px" %)AT+DR=?|(% style="width:151px" %)View the current DR settings|(% style="width:92px" %)OK|(% style="width:206px" %)
621 -|(% style="width:130px" %)AT+DR=1|(% style="width:151px" %)(((
622 -set DR to 1
623 -It takes effect only when ADR=0
624 -)))|(% style="width:92px" %)OK|(% style="width:206px" %)(((
625 -0X22000101:
626 -00: ADR=0
627 -01: DR=1
628 -01: TXP=1
629 -22: fixed command
630 -)))
631 -|(% style="width:130px" %)AT+TXP=?|(% style="width:151px" %)View the current TXP|(% style="width:92px" %)OK|(% style="width:206px" %)
632 -|(% style="width:130px" %)AT+TXP=1|(% style="width:151px" %)(((
633 -set TXP to 1
634 -It takes effect only when ADR=0
635 -)))|(% style="width:92px" %)OK|(% style="width:206px" %)(((
636 -0X22000101:
637 -00: ADR=0
638 -01: DR=1
639 -01: TXP=1
640 -22: fixed command
641 -)))
642 -|(% style="width:130px" %)AT+RJTDC=10|(% style="width:151px" %)Set RJTDC time interval|(% style="width:92px" %)OK|(% style="width:206px" %)(((
643 -0X26000A:
644 -26: fixed command
645 -000A: 0X000A=10(min)
646 -for details, check wiki
647 -)))
648 -|(% style="width:130px" %) |(% style="width:151px" %)(((
649 -(((
650 -~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_
651 -
652 -Retrieve stored data for a specified period of time
653 -)))
654 -
655 -(((
656 -
657 -)))
658 -)))|(% style="width:92px" %) |(% style="width:206px" %)(((
659 -0X3161DE7C7061DE8A800A:
660 -31: fixed command
661 -61DE7C70:0X61DE7C70=2022/1/12 15:00:00
662 -61DE8A80:0X61DE8A80=2022/1/12 16:00:00
663 -0A: 0X0A=10(second)
664 -View details 2.6.2
665 -)))
666 -|(% style="width:130px" %)AT+DDETECT=?|(% style="width:151px" %)View the current DDETECT setting status and time|(% style="width:92px" %)(((
667 -1,1440,2880
668 -OK
669 -)))|(% style="width:206px" %)Default 1,1440,2880(min)
670 -|(% style="width:130px" %)AT+DDETECT=(((
671 -1,1440,2880
672 -)))|(% style="width:151px" %)(((
673 -Set DDETECT setting status and time
674 -((% style="color:red" %)When the node does not receive the downlink packet within the set time, it will re-enter the network(%%))
675 -)))|(% style="width:92px" %)OK|(% style="width:206px" %)(((
676 -0X320005A0: close
677 -0X320105A0: open
678 -32: fixed command
679 -05A0: 0X05A0=1440(min)
680 -)))
681 -
682 -== 3.2  Set Password ==
683 -
684 -
685 -Feature: Set device password, max 9 digits.
686 -
687 -(% style="color:#4f81bd" %)**AT Command: AT+PWORD**
688 -
689 -(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:372px" %)
690 -|(% style="background-color:#4f81bd; color:white; width:155px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:128px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:89px" %)**Response**
691 -|(% style="width:155px" %)AT+PWORD=?|(% style="width:124px" %)Show password|(% style="width:86px" %)(((
692 -123456
693 -OK
694 -)))
695 -|(% style="width:155px" %)AT+PWORD=999999|(% style="width:124px" %)Set password|(% style="width:86px" %)OK
696 -
697 -(% style="color:#4f81bd" %)**Downlink Command:**
698 -
699 -No downlink command for this feature.
700 -
701 -
702 -== 3.3  Set button sound and ACK sound ==
703 -
704 -
705 -Feature: Turn on/off button sound and ACK alarm.
706 -
707 -(% style="color:#4f81bd" %)**AT Command: AT+SOUND**
708 -
709 -(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:372px" %)
710 -|(% style="background-color:#4f81bd; color:white; width:155px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:128px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:89px" %)**Response**
711 -|(% style="width:155px" %)(((
712 -AT+SOUND=?
713 -)))|(% style="width:124px" %)Get the current status of button sound and ACK sound|(% style="width:86px" %)(((
714 -1,1
715 -OK
716 -)))
717 -|(% style="width:155px" %)(((
718 -AT+SOUND=0,1
719 -)))|(% style="width:124px" %)Turn off the button sound and turn on ACK sound|(% style="width:86px" %)OK
720 -
721 -(% style="color:#4f81bd" %)**Downlink Command: 0xA1 **
722 -
723 -Format: Command Code (0xA1) followed by 2 bytes mode value.
724 -
725 -The first byte after 0XA1 sets the button sound, and the second byte after 0XA1 sets the ACK sound.** (0: off, 1: on)**
726 -
727 -* **Example: **Downlink Payload: A10001  ~/~/ Set AT+SOUND=0,1  Turn off the button sound and turn on ACK sound.
728 -
729 -== 3.4  Set buzzer music type(0~~4) ==
730 -
731 -
732 -Feature: Set different alarm key response sounds.There are five different types of button music.
733 -
734 -(% style="color:#4f81bd" %)**AT Command: AT+OPTION**
735 -
736 -(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:372px" %)
737 -|(% style="background-color:#4f81bd; color:white; width:155px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:128px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:89px" %)**Response**
738 -|(% style="width:155px" %)(((
739 -AT+OPTION=?
740 -)))|(% style="width:124px" %)(((
741 -Get the buzzer music type
742 -)))|(% style="width:86px" %)(((
743 -3
744 -
745 -OK
746 -)))
747 -|(% style="width:155px" %)AT+OPTION=1|(% style="width:124px" %)Set the buzzer music to type 1|(% style="width:86px" %)OK
748 -
749 -(% style="color:#4f81bd" %)**Downlink Command: 0xA3**
750 -
751 -Format: Command Code (0xA3) followed by 1 byte mode value.
752 -
753 -* **Example: **Downlink Payload: A300  ~/~/ Set AT+OPTION=0  Set the buzzer music to type 0.
754 -
755 -== 3.5  Set Valid Push Time ==
756 -
757 -
758 -Feature: Set the holding time for pressing the alarm button to avoid miscontact. Values range from** 0 ~~1000ms**.
759 -
760 -(% style="color:#4f81bd" %)**AT Command: AT+STIME**
761 -
762 -(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:372px" %)
763 -|(% style="background-color:#4f81bd; color:white; width:155px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:128px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:89px" %)**Response**
764 -|(% style="width:155px" %)(((
765 -AT+STIME=?
766 -)))|(% style="width:124px" %)(((
767 -Get the button sound time
768 -)))|(% style="width:86px" %)(((
769 -0
770 -OK
771 -)))
772 -|(% style="width:155px" %)(((
773 -AT+STIME=1000
774 -)))|(% style="width:124px" %)Set the button sound time to 1000**ms**|(% style="width:86px" %)OK
775 -
776 -(% style="color:#4f81bd" %)**Downlink Command: 0xA2**
777 -
778 -Format: Command Code (0xA2) followed by 2 bytes mode value.
779 -
780 -* **Example: **Downlink Payload: A203E8  ~/~/ Set AT+STIME=1000  
781 -
782 -**~ Explain: **Hold the alarm button for 10 seconds before the node will send the alarm packet.
783 -
784 -
785 -
786 -= 4.  Battery & How to replace =
787 -
788 -== 4.1  Battery Type and replace ==
789 -
790 -
791 -PB01 uses 2 x AAA LR03(1.5v) batteries. If the batteries running low (shows 2.1v in the platform). Users can buy generic AAA battery and replace it.
792 -
793 -(% style="color:red" %)**Note: **
794 -
795 -1.  The PB01 doesn't have any screw, users can use nail to open it by the middle.
796 -
797 -[[image:image-20220621143535-5.png]]
798 -
799 -
800 -2.  Make sure the direction is correct when install the AAA batteries.
801 -
802 -[[image:image-20220621143535-6.png]]
803 -
804 -
805 -== 4.2  Power Consumption Analyze ==
806 -
807 -
808 -Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
809 -
810 -Instruction to use as below:
811 -
812 -(% style="color:blue" %)**Step 1**(%%):  Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from:
813 -
814 -[[battery calculator>>https://www.dropbox.com/sh/sxrgszkac4ips0q/AAA4XjBI3HAHNpdbU3ALN1j0a/Battery%20Document/Battery_Analyze?dl=0&subfolder_nav_tracking=1]]
815 -
816 -
817 -(% style="color:blue" %)**Step 2**(%%):  (% style="display:none" %) (%%)Open it and choose
818 -
819 -* Product Model
820 -* Uplink Interval
821 -* Working Mode
822 -
823 -And the Life expectation in difference case will be shown on the right.
824 -
825 -[[image:image-20220621143643-7.png||height="429" width="1326"]]
826 -
827 -
828 -= 5.  Accessories =
829 -
830 -
831 -* (((
832 -(% class="wikigeneratedid" id="H5.2A0ProgramConverter28AS-0229" %)
833 -**Program Converter (AS-02)**
834 -)))
835 -
836 -AS-02 is an optional accessory, it is USB Type-C converter. AS-02 provide below feature:
837 -
838 -1. Access AT console of PB01 when used with USB-TTL adapter. [[See this link>>||anchor="H6.1HowtouseATCommandtoconfigurePB01"]].
839 -
840 -[[image:image-20220621141724-3.png]]
841 -
842 -
843 843  = 6. FAQ =
844 844  
845 -== 6.1 How to use AT Command to configure PB01 ==
301 +== 6.1 ==
846 846  
847 847  
848 -PB01 supports AT Command set. Users can use a USB to TTL adapter plus the Program Cable to connect to PB01 for using AT command, as below.
849 -
850 -[[image:image-20240511085914-1.png||height="570" width="602"]]
851 -
852 -
853 -**Connection:**
854 -
855 -* (% style="background-color:yellow" %)USB to TTL GND <~-~-> Program Converter GND pin
856 -* (% style="background-color:yellow" %)USB to TTL RXD  <~-~-> Program Converter D+ pin
857 -* (% style="background-color:yellow" %)USB to TTL TXD  <~-~-> Program Converter A11 pin
858 -
859 -(((
860 -In PC, User needs to set **serial tool**(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to (% style="color:green" %)**9600**(%%) to access to access serial console for PB01. The AT commands are disable by default and need to enter password (default:(% style="color:green" %)**123456**(%%)) to active it. Timeout to input AT Command is 5 min, after 5-minute, user need to input password again.
861 -)))
862 -
863 -(((
864 -Input password and ATZ to activate PB01, as shown below:
865 -)))
866 -
867 -[[image:image-20240510174509-18.png||height="572" width="791"]]
868 -
869 -
870 -== 6.2  AT Command and Downlink ==
871 -
872 -
873 -(((
874 -Sending ATZ will reboot the node
875 -)))
876 -
877 -(((
878 -Sending AT+FDR will restore the node to factory settings
879 -)))
880 -
881 -(((
882 -Get the node's AT command setting by sending AT+CFG
883 -)))
884 -
885 -(((
886 -
887 -)))
888 -
889 -(((
890 -**Example：**                                           
891 -)))
892 -
893 -(((
894 -AT+DEUI=FA 23 45 55 55 55 55 51
895 -
896 -AT+APPEUI=FF AA 23 45 42 42 41 11
897 -
898 -AT+APPKEY=AC D7 35 81 63 3C B6 05 F5 69 44 99 C1 12 BA 95
899 -
900 -AT+DADDR=FFFFFFFF
901 -
902 -AT+APPSKEY=FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
903 -
904 -AT+NWKSKEY=FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
905 -
906 -AT+ADR=1
907 -
908 -AT+TXP=7
909 -
910 -AT+DR=5
911 -
912 -AT+DCS=0
913 -
914 -AT+PNM=1
915 -
916 -AT+RX2FQ=869525000
917 -
918 -AT+RX2DR=0
919 -
920 -AT+RX1DL=5000
921 -
922 -AT+RX2DL=6000
923 -
924 -AT+JN1DL=5000
925 -
926 -AT+JN2DL=6000
927 -
928 -AT+NJM=1
929 -
930 -AT+NWKID=00 00 00 13
931 -
932 -AT+FCU=61
933 -
934 -AT+FCD=11
935 -
936 -AT+CLASS=A
937 -
938 -AT+NJS=1
939 -
940 -AT+RECVB=0:
941 -
942 -AT+RECV=
943 -
944 -AT+VER=EU868 v1.0.0
945 -
946 -AT+CFM=0,7,0
947 -
948 -AT+SNR=0
949 -
950 -AT+RSSI=0
951 -
952 -AT+TDC=1200000
953 -
954 -AT+PORT=2
955 -
956 -AT+PWORD=123456
957 -
958 -AT+CHS=0
959 -
960 -AT+RX1WTO=24
961 -
962 -AT+RX2WTO=6
963 -
964 -AT+DECRYPT=0
965 -
966 -AT+RJTDC=20
967 -
968 -AT+RPL=0
969 -
970 -AT+TIMESTAMP=systime= 2024/5/11 01:10:58 (1715389858)
971 -
972 -AT+LEAPSEC=18
973 -
974 -AT+SYNCMOD=1
975 -
976 -AT+SYNCTDC=10
977 -
978 -AT+SLEEP=0
979 -
980 -AT+ATDC=1
981 -
982 -AT+UUID=003C0C53013259E0
983 -
984 -AT+DDETECT=1,1440,2880
985 -
986 -AT+SETMAXNBTRANS=1,0
987 -
988 -AT+DISFCNTCHECK=0
989 -
990 -AT+DISMACANS=0
991 -
992 -AT+PNACKMD=0
993 -
994 -AT+SOUND=0,0
995 -
996 -AT+STIME=0
997 -
998 -AT+OPTION=3
999 -)))
1000 -
1001 -(((
1002 -**Example：**
1003 -)))
1004 -
1005 -[[image:image-20240511091518-2.png||height="601" width="836"]]
1006 -
1007 -
1008 -== 6.3  How to upgrade the firmware? ==
1009 -
1010 -
1011 -PB01 requires a program converter to upload images to PB01, which is used to upload image to PB01 for:
1012 -
1013 -* Support new features
1014 -* For bug fix
1015 -* Change LoRaWAN bands.
1016 -
1017 - PB01 internal program is divided into bootloader and work program, shipping is included bootloader, the user can choose to directly update the work program.
1018 -
1019 -If the bootloader is erased for some reason, users will need to download the boot program and the work program.
1020 -
1021 -
1022 -=== 6.3.1 Update firmware (Assume device have bootloader) ===
1023 -
1024 -
1025 -(% style="color:blue" %)**Step 1**(%%):** Connect UART as per FAQ 6.1**
1026 -
1027 -(% style="color:blue" %)**Step 2**(%%):** Update follow [[Instruction for update via DraginoSensorManagerUtility.exe>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H3.2.1UpdateafirmwareviaDraginoSensorManagerUtility.exe]]. **
1028 -
1029 -
1030 -=== 6.3.2 Update firmware (Assume device doesn't have bootloader) ===
1031 -
1032 -
1033 -Download both the boot program and the worker program** . **After update , device will have bootloader so can use above 6.3.1 method to update woke program.
1034 -
1035 -(% style="color:blue" %)**Step 1**(%%):** **Install [[TremoProgrammer>>url:https://www.dropbox.com/scl/fo/gk1rb5pnnjw4kv5m5cs0z/h?rlkey=906ouvgbvif721f9bj795vfrh&dl=0]]  first.
1036 -
1037 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220615170542-5.png?rev=1.1||alt="image-20220615170542-5.png"]]
1038 -
1039 -(% style="color:blue" %)**Step 2**(%%): Hardware Connection
1040 -
1041 -Connect PC and PB01 via USB-TTL adapter .
1042 -
1043 -(% style="color:red" %)**Note: To download firmware in this way, you need to pull the boot pin(Program Converter D- pin) high to enter the burn mode. After burning, disconnect the boot pin of the node and the 3V3 pin of the USB-TTL adapter, and reset the node to exit the burning mode.**
1044 -
1045 -**Connection:**
1046 -
1047 -* (% style="background-color:yellow" %)USB-TTL GND <~-~-> Program Converter GND pin
1048 -* (% style="background-color:yellow" %)USB-TTL RXD  <~-~-> Program Converter D+ pin
1049 -* (% style="background-color:yellow" %)USB-TTL TXD  <~-~-> Program Converter A11 pin
1050 -* (% style="background-color:yellow" %)USB-TTL 3V3 <~-~-> Program Converter D- pin
1051 -
1052 -(% style="color:blue" %)**Step 3**(%%):** **Select the device port to be connected, baud rate and bin file to be downloaded.
1053 -
1054 -[[image:image-20240701160913-1.png]]
1055 -
1056 -Users need to reset the node to start downloading the program.
1057 -~1. Reinstall the battery to reset the node
1058 -2. Hold down the ACT button to reset the node (see [[2.7>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/PB01--LoRaWAN_Button_User_Manual/#H2.7Button]] ).
1059 -
1060 -When this interface appears, it indicates that the download has been completed.
1061 -
1062 -[[image:image-20240701160924-2.png]]
1063 -
1064 -Finally, Disconnect Program Converter D- pin, reset the node again , and the node exits burning mode.
1065 -
1066 -
1067 -== 6.4  How to change the LoRa Frequency Bands/Region? ==
1068 -
1069 -
1070 -User can follow the introduction for [[how to upgrade image>>||anchor="H6.3A0Howtoupgradethefirmware3F"]]. When download the images, choose the required image file for download.
1071 -
1072 -
1073 -== 6.5 Why i see different working temperature for the device? ==
1074 -
1075 -
1076 -The working temperature range of device depends on the battery user choose.
1077 -
1078 -* Normal AAA Battery can support -10 ~~ 50°C working range.
1079 -* Special AAA battery can support -40 ~~ 60 °C working range. For example: [[Energizer L92>>https://data.energizer.com/pdfs/l92.pdf]]
1080 -
1081 1081  = 7. Order Info =
1082 1082  
1083 1083  == 7.1  Part Number ==
1084 1084  
308 +
1085 1085  Part Number: (% style="color:#4472c4" %)LTS5
1086 1086  
1087 -
1088 1088  
1089 1089  == 7.2  Packing Info ==
1090 1090  
314 +
1091 1091  **Package Includes**:
1092 1092  
1093 1093  * LTS5 HMI Touch Screen
... ... @@ -1097,6 +1097,7 @@
1097 1097  
1098 1098  = 8. Support =
1099 1099  
324 +
1100 1100  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
1101 1101  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]].
1102 1102  
... ... @@ -1103,6 +1103,7 @@
1103 1103  
1104 1104  = 9.  Reference material =
1105 1105  
331 +
1106 1106  * Datasheet
1107 1107  * Source Code
1108 1108  * Mechinical
1727229396732-319.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +197.2 KB
Content
1727229550717-684.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +113.9 KB
Content
1727229582471-566.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +73.6 KB
Content
1727229618724-758.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +118.7 KB
Content
1727229653254-680.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +116.2 KB
Content
1727229682537-381.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +51.5 KB
Content
1727229715361-392.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +75.2 KB
Content
1727229740592-843.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +87.3 KB
Content
1727229760857-521.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +24.7 KB
Content
1727229798126-306.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +53.6 KB
Content
1727229821582-258.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +76.1 KB
Content
1727229845835-509.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +68.3 KB
Content
1727229892636-154.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +192.0 KB
Content
1727229926561-300.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +178.0 KB
Content
1727229955611-607.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +100.4 KB
Content
1727229990795-405.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +383.6 KB
Content
1727230012478-930.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +477.1 KB
Content
1727231038705-173.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +94.6 KB
Content
1727233636007-933.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +114.8 KB
Content
1727484665746-713.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +94.9 KB
Content
1727485118799-984.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +11.8 KB
Content
1727485251053-655.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +20.4 KB
Content
1727485480434-713.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +24.7 KB
Content
1727485933579-550.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +55.6 KB
Content
1727485953726-175.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +91.6 KB
Content
1727486567182-334.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +42.6 KB
Content
1727486578489-774.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +66.0 KB
Content
1727487368023-281.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +28.5 KB
Content
1727488067077-684.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +604.7 KB
Content
1727488099947-341.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +877.7 KB
Content
1727488108117-780.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +877.7 KB
Content
1727488157579-949.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +877.7 KB
Content
image-20240916101737-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Edwin
Size
... ... @@ -1,0 +1,1 @@
1 +156.7 KB
Content
image-20240925110638-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +262.7 KB
Content
image-20240928090825-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +30.2 KB
Content
image-20240928103357-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +153.7 KB
Content
image-20240928103506-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +197.7 KB
Content
image-20240928105309-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +80.2 KB
Content
image-20240928110211-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +228.0 KB
Content
image-20240928111412-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +150.9 KB
Content
image-20240928111654-7.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +105.4 KB
Content
image-20240928112001-8.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +75.6 KB
Content
image-20240928113424-9.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +50.8 KB
Content
image-20240928114139-10.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +114.3 KB
Content
image-20240928144830-11.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.xieby
Size
... ... @@ -1,0 +1,1 @@
1 +25.5 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0