LT-22222-L LoRa IO Controller User Manual

The Dragino LT series I/O Modules are Long Range LoRaWAN I/O Controller. It contains different I/O Interfaces such as: analog current Input, analog voltage input, relay output, digital input and digital output etc. The LT I/O Modules are designed to simplify the installation of I/O monitoring.

15

)))

16

17

(((

18

The LT I/O Controllers allows the user to send data and reach extremely long ranges. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption. It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on.

)))

(((

The LT I/O Controllers is aiming to provide a simple plug and play, low cost installation by using LoRaWAN wireless technology.

)))

(((

The use environment includes:

)))

(((

1) If user’s area has LoRaWAN service coverage, they can just install the I/O controller and configure it to connect the LoRaWAN provider via wireless.

)))

(((

2) User can set up a LoRaWAN gateway locally and configure the controller to connect to the gateway via wireless.

)))

(((

[[image:1653295757274-912.png]]

39

)))

40

41

== 1.2 Specifications ==

**Hardware System:**

* STM32L072CZT6 MCU

* SX1276/78 Wireless Chip

47

* Power Consumption:

48

** Idle: 4mA@12v

49

** 20dB Transmit: 34mA@12v

50

51

**Interface for Model: LT22222-L:**

52

53

* 2 x Digital dual direction Input (Detect High/Low signal, Max: 50v, or 220v with optional external resistor)

54

* 2 x Digital Output (NPN output. Max pull up voltage 36V,450mA)

55

* 2 x Relay Output (5A@250VAC / 30VDC)

56

* 2 x 0~~20mA Analog Input (res:0.01mA)

57

* 2 x 0~~30V Analog Input (res:0.01v)

58

* Power Input 7~~ 24V DC.

**LoRa Spec:**

* Frequency Range:

** Band 1 (HF): 862 ~~ 1020 Mhz

64

** Band 2 (LF): 410 ~~ 528 Mhz

65

* 168 dB maximum link budget.

66

* +20 dBm - 100 mW constant RF output vs.

67

* +14 dBm high efficiency PA.

68

* Programmable bit rate up to 300 kbps.

69

* High sensitivity: down to -148 dBm.

70

* Bullet-proof front end: IIP3 = -12.5 dBm.

71

* Excellent blocking immunity.

72

* Low RX current of 10.3 mA, 200 nA register retention.

73

* Fully integrated synthesizer with a resolution of 61 Hz.

74

* FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.

75

* Built-in bit synchronizer for clock recovery.

76

* Preamble detection.

77

* 127 dB Dynamic Range RSSI.

78

* Automatic RF Sense and CAD with ultra-fast AFC.

79

* Packet engine up to 256 bytes with CRC.

== 1.3 Features ==

* LoRaWAN Class A & Class C protocol

84

* Optional Customized LoRa Protocol

85

* Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/RU864/IN865

86

* AT Commands to change parameters

87

* Remote configure parameters via LoRa Downlink

88

* Firmware upgradable via program port

89

* Counting

90

91

== 1.4 Applications ==

92

93

* Smart Buildings & Home Automation

94

* Logistics and Supply Chain Management

* Smart Metering

* Smart Agriculture

* Smart Cities

* Smart Factory

== 1.5 Hardware Variants ==

101

102

(% border="1" style="background-color:#f7faff; width:500px" %)

103

|(% style="width:103px" %)**Model**|(% style="width:131px" %)**Photo**|(% style="width:334px" %)**Description**

104

|(% style="width:103px" %)**LT22222-L**|(% style="width:131px" %)[[image:1653296302983-697.png]]|(% style="width:334px" %)(((

105

* 2 x Digital Input (Bi-direction)

106

* 2 x Digital Output

107

* 2 x Relay Output (5A@250VAC / 30VDC)

108

* 2 x 0~~20mA Analog Input (res:0.01mA)

109

* 2 x 0~~30V Analog Input (res:0.01v)

* 1 x Counting Port

)))

= 2. Power ON Device =

114

115

The LT controller can be powered by 7 ~~ 24V DC power source. Connect VIN to Power Input V+ and GND to power input V- to power the LT controller.

116

117

(((

118

PWR will on when device is properly powered.

119

)))

120

121

[[image:1653297104069-180.png]]

122

123

= 3. Operation Mode =

124

125

== 3.1 How it works? ==

126

127

The LT is configured as LoRaWAN OTAA Class C mode by default. It has OTAA keys to join network. To connect a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the LT. It will auto join the network via OTAA. For LT-22222-L, the LED will show the Join status: After power on **TX LED** will fast blink 5 times, LT-22222-L will enter working mode and start to JOIN LoRaWAN network. **TX LED** will be on for 5 seconds after joined in network. When there is message from server, the **RX LED** will be on for 1 second.

128

129

In case user can’t set the OTAA keys in the network server and has to use the existing keys from server. User can [[use AT Command>>path:#AT_Command]] to set the keys in the devices.

130

131

3.2 Example to join LoRaWAN network

132

133

This chapter shows an example for how to join the TTN LoRaWAN Network. Below is the network structure, we use our LG308 as LoRaWAN gateway here.

134

135

[[image:image-20220523172350-1.png||height="266" width="864"]]

(((

The LG308 is already set to connect to [[TTN network >>url:https://www.thethingsnetwork.org/]]. So what we need to do now is only configure register this device to TTN:

)))

(((

**Step 1**: Create a device in TTN with the OTAA keys from LT IO controller.

)))

(((

Each LT is shipped with a sticker with the default device EUI as below:

148

)))

149

150

[[image:1653297924498-393.png]]

151

152

Input these keys in the LoRaWAN Server portal. Below is TTN screen shot:

153

154

Add APP EUI in the application.

155

156

[[image:1653297955910-247.png||height="321" width="716"]]

157

158

Add APP KEY and DEV EUI

159

160

[[image:1653298023685-319.png]]

161

162

(((

163

**Step 2**: Power on LT and it will auto join to the TTN network. After join success, it will start to upload message to TTN and user can see in the panel.

164

)))

165

166

[[image:1653298044601-602.png||height="405" width="709"]]

167

168

== 3.3 Uplink Payload ==

169

170

There are five working modes + one interrupt mode on LT for different type application:

171

172

* **MOD1**: (default setting): 2 x ACI + 2AVI + DI + DO + RO

173

* **MOD2**: Double DI Counting + DO + RO

174

* **MOD3**: Single DI Counting + 2 x ACI + DO + RO

175

* **MOD4**: Single DI Counting + 1 x Voltage Counting + DO + RO

176

* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO

177

* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5

178

179

=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===

180

181

The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.

182

183

[[image:image-20220523174024-3.png]]

184

185

(((

186

(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below

187

)))

188

189

[[image:image-20220523174254-4.png]]

190

191

* RO is for relay. ROx=1 : close，ROx=0 always open.

192

* DI is for digital input. DIx=1: high or float, DIx=0: low.

193

* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.

194

195

(% style="color:red" %)Note: DI3 and DO3 bit are not valid for LT-22222-L

196

197

For example if payload is: [[image:image-20220523175847-2.png]]

198

199

**The value for the interface is: **

200

201

AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V

202

203

AVI2 channel voltage is 0x04AC/1000=1.196V

204

205

ACI1 channel current is 0x1310/1000=4.880mA

206

207

ACI2 channel current is 0x1300/1000=4.864mA

208

209

The last byte 0xAA= 10101010(B) means

210

211

* [1] RO1 relay channel is close and the RO1 LED is ON.

212

* [0] RO2 relay channel is open and RO2 LED is OFF;

**LT22222-L:**

* [1] DI2 channel is high input and DI2 LED is ON;

217

* [0] DI1 channel is low input;

218

219

* [0] DO3 channel output state

220

** DO3 is float in case no load between DO3 and V+.;

221

** DO3 is high in case there is load between DO3 and V+.

222

** DO3 LED is off in both case

223

* [1] DO2 channel output is low and DO2 LED is ON.

224

* [0] DO1 channel output state

225

** DO1 is float in case no load between DO1 and V+.;

226

** DO1 is high in case there is load between DO1 and V+.

227

** DO1 LED is off in both case

228

229

=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===

230

231

**For LT-22222-L**: this mode the **DI1 and DI2** are used as counting pins.

232

233

Total : 11 bytes payload

234

235

[[image:image-20220523180452-3.png]]

236

237

(((

238

(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DO3, DO2 and DO1. Totally 1bytes as below

239

)))

240

241

[[image:image-20220523180506-4.png]]

242

243

* RO is for relay. ROx=1 : close，ROx=0 always open.

244

* FIRST: Indicate this is the first packet after join network.

245

* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.

246

247

(% style="color:red" %)Note: DO3 bit is not valid for LT-22222-L.

248

249

**To use counting mode, please run:**

250

251

(% class="box infomessage" %)

(((

**AT+MOD=2**

)))

(% class="box infomessage" %)

(((

**ATZ**

)))

(% style="color:#4f81bd" %)**AT Commands for counting:**

**For LT22222-L:**

(% class="box infomessage" %)

266

(((

267

**AT+TRIG1=0,100 (set DI1 port to trigger on low level, valid signal is 100ms) **

268

)))

269

270

(% class="box infomessage" %)

271

(((

272

**AT+TRIG1=1,100(set DI1 port to trigger on high level, valid signal is 100ms ) **

273

)))

274

275

(% class="box infomessage" %)

276

(((

277

**AT+TRIG2=0,100 (set DI2 port to trigger on low level, valid signal is 100ms) **

278

)))

279

280

(% class="box infomessage" %)

281

(((

282

**AT+TRIG2=1,100 (set DI2 port to trigger on high level, valid signal is 100ms ) **

283

)))

284

285

(% class="box infomessage" %)

286

(((

287

**AT+SETCNT=1,60 (Set COUNT1 value to 60)**

288

)))

289

290

(% class="box infomessage" %)

291

(((

292

**AT+SETCNT=2,60 (Set COUNT2 value to 60)**

293

)))

294

295

=== 3.3.3 AT+MOD~=3, Single DI Counting + 2 x ACI ===

296

297

**LT22222-L**: This mode the DI1 is used as a counting pin.

298

299

[[image:image-20220523181246-5.png]]

300

301

(((

302

(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below

303

)))

304

305

[[image:image-20220523181301-6.png]]

306

307

* RO is for relay. ROx=1 : close，ROx=0 always open.

308

* FIRST: Indicate this is the first packet after join network.

309

* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.

310

311

(% style="color:red" %)Note: DO3 is not valid for LT-22222-L.

312

313

**To use counting mode, please run:**

314

315

(% class="box infomessage" %)

(((

**AT+MOD=3**

)))

(% class="box infomessage" %)

(((

**ATZ**

)))

Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:#COUNT_COMMAND]].

326

327

=== 3.3.4 AT+MOD~=4, Single DI Counting + 1 x Voltage Counting ===

328

329

**LT22222-L**: This mode the DI1 is used as a counting pin.

330

331

The AVI1 is also used for counting. AVI1 is used to monitor the voltage. It will check the voltage **every 60s**, if voltage is higher or lower than VOLMAX mV, the AVI1 Counting increase 1, so AVI1 counting can be used to measure a machine working hour.

332

333

[[image:image-20220523181903-8.png]]

334

335

(((

336

(% style="color:#4f81bd" %)**DIDORO **(%%)is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below

337

)))

338

339

[[image:image-20220523181727-7.png]]

340

341

* RO is for relay. ROx=1 : close，ROx=0 always open.

342

* FIRST: Indicate this is the first packet after join network.

343

* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.

344

345

(% style="color:red" %)Note: DO3 is not valid for LT-22222-L.

346

347

**To use this mode, please run:**

348

349

(% class="box infomessage" %)

(((

**AT+MOD=4**

)))

(% class="box infomessage" %)

(((

**ATZ**

)))

Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:#COUNT_COMMAND]].

361

362

**Plus below command for AVI1 Counting:**

363

364

(% class="box infomessage" %)

365

(((

366

**AT+SETCNT=3,60 (set AVI Count to 60)**

367

)))

368

369

(% class="box infomessage" %)

370

(((

371

**AT+VOLMAX=20000 (If AVI1 voltage higher than VOLMAX (20000mV =20v), counter increase 1)**

372

)))

373

374

(% class="box infomessage" %)

375

(((

376

**AT+VOLMAX=20000,0 (If AVI1 voltage lower than VOLMAX (20000mV =20v), counter increase 1)**

377

)))

378

379

(% class="box infomessage" %)

380

(((

381

**AT+VOLMAX=20000,1 (If AVI1 voltage higer than VOLMAX (20000mV =20v), counter increase 1)**

382

)))

383

384

=== 3.3.5 AT+MOD~=5, Single DI Counting + 2 x AVI + 1 x ACI ===

385

386

**LT22222-L**: This mode the DI1 is used as a counting pin.

387

388

[[image:image-20220523182334-9.png]]

389

390

(((

391

(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below

)))

* RO is for relay. ROx=1 : close，ROx=0 always open.

396

* FIRST: Indicate this is the first packet after join network.

397

* DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.

398

399

(% style="color:red" %)Note: DO3 is not valid for LT-22222-L.

400

401

**To use this mode, please run:**

402

403

(% class="box infomessage" %)

(((

**AT+MOD=5**

)))

(% class="box infomessage" %)

(((

**ATZ**

)))

Other AT Commands for counting are similar to [[MOD2 Counting Command>>path:#COUNT_COMMAND]].

1.

11.

111. AT+ADDMOD=6. (Trigger Mode, Optional)

422

423

**This mode is an optional mode for trigger purpose. It can run together with other mode.**

424

425

For example, if user has configured below commands:

426

427

* AT+MOD=1 à The normal working mode

428

* AT+ADDMOD6=1 à Enable trigger

429

430

LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:

431

432

1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN **unconfirmed** data type

433

1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN **CONFIRMED data type.**

434

435

**AT Command to set Trigger Condition**:

436

437

**Trigger base on voltage**:

438

439

Format: AT+AVLIM=<AV1_LIMIT_LOW>,< AV1_LIMIT_HIGH>,<AV2_LIMIT_LOW>,< AV2_LIMIT_HIGH>

Example:

AT+AVLIM=3000,6000,0,2000 (If AVI1 voltage lower than 3v or higher than 6v. or AV2 voltage is higher than 2v, LT will trigger Uplink)

444

445

AT+AVLIM=5000,0,0,0 (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)

446

447

448

**Trigger base on current**:

449

450

Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>

Example:

AT+ACLIM=10000,15000,0,0 (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)

455

456

457

**Trigger base on DI status**:

458

459

DI status trigger Flag.

460

461

Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >

Example:

AT+ DTRI =1,0 (Enable DI1 trigger / disable DI2 trigger)

**Downlink Command to set Trigger Condition**

472

473

Type Code: 0xAA. Downlink command same as AT Command [[AT+AVLIM, AT+ACLIM>>path:#AT_Trigger]]

474

475

Format: AA xx yy1 yy1 yy2 yy2 yy3 yy3 yy4 yy4

476

477

AA: Code for this downlink Command:

478

479

xx: 0: Limit for AV1 and AV2; 1: limit for AC1 and AC2 ; 2 DI1, DI2 trigger enable/disable

480

481

yy1 yy1: AC1 or AV1 low limit or DI1/DI2 trigger status.

482

483

yy2 yy2: AC1 or AV1 high limit.

484

485

yy3 yy3: AC2 or AV2 low limit.

486

487

Yy4 yy4: AC2 or AV2 high limit.

488

489

490

Example1: AA 00 13 88 00 00 00 00 00 00

491

492

Same as AT+AVLIM=5000,0,0,0 (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)

493

494

Example2: AA 02 01 00

495

496

Same as AT+ DTRI =1,0 (Enable DI1 trigger / disable DI2 trigger)

**Trigger Settings Payload Explanation:**

502

503

MOD6 Payload : total 11 bytes payload

504

505

(% border="1" style="background-color:#f7faff" %)

506

|Size(bytes)|1|1|1|6|1|1

|Value|(((

TRI_A

FLAG

)))|(((

TRI_A

Status

)))|(((

TRI_DI

FLAG+STA

)))|Reserve|Enable/Disable MOD6|(((

MOD

(6)

)))

**TRI FLAG1** is a combination to show if trigger is set for this part. Totally 1byte as below

526

527

(% border="1" style="background-color:#f7faff" %)

528

|bit7|bit6|bit5|bit4|bit3|bit2|bit1|bit0

|(((

AV1_

LOW

)))|(((

AV1_

HIGH

)))|(((

AV2_

LOW

)))|(((

AV2_

HIGH

)))|(((

AC1_

LOW

)))|(((

AC1_

HIGH

)))|(((

AC2_

LOW

)))|(((

AC2_

HIGH

)))

* Each bits shows if the corresponding trigger has been configured.

Example:

10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW

568

569

570

**TRI Status1** is a combination to show which condition is trigger. Totally 1byte as below

571

572

(% border="1" style="background-color:#f7faff" %)

573

|bit7|bit6|bit5|bit4|bit3|bit2|bit1|bit0

|(((

AV1_

LOW

)))|(((

AV1_

HIGH

)))|(((

AV2_

LOW

)))|(((

AV2_

HIGH

)))|(((

AC1_

LOW

)))|(((

AC1_

HIGH

)))|(((

AC2_

LOW

)))|(((

AC2_

HIGH

)))

* Each bits shows which status has been trigger on this uplink.

Example:

10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.

**TRI_DI FLAG+STA **is a combination to show which condition is trigger. Totally 1byte as below

618

619

(% border="1" style="background-color:#f7faff" %)

620

|bit7|bit6|bit5|bit4|bit3|bit2|bit1|bit0

621

|N/A|N/A|N/A|N/A|DI2_STATUS|DI2_FLAG|DI1_STATUS|DI1_FLAG

622

623

* Each bits shows which status has been trigger on this uplink.

Example:

00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.

628

629

00000101: Means both DI1 and DI2 trigger are enabled.

630

631

632

**Enable/Disable MOD6 **: 0x01: MOD6 is enable. 0x00: MOD6 is disable.

633

634

635

Downlink command to poll MOD6 status:

AB 06

When device got this command, it will send the MOD6 payload.

1.

11.

111. Payload Decoder

**Decoder for TTN/loraserver/ChirpStack**: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/Payload_decoder/>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/Payload_decoder/]]

1.

11. Configure LT via AT or Downlink

656

657

User can configure LT I/O Controller via [[AT Commands >>path:#_Using_the_AT]]or LoRaWAN Downlink Commands

658

659

There are two kinds of Commands:

660

661

* **Common Commands**: They should be available for each sensor, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands

662

663

* **Sensor Related Commands**: These commands are special designed for LT-22222-L. User can see these commands below:

1.

11.

111. Common Commands:

668

669

They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: http:~/~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands

1.

11.

111. Sensor related commands:

675

676

==== Set Transmit Interval ====

677

678

Set device uplink interval.

* AT Command:

AT+TDC=N

Example: AT+TDC=30000. Means set interval to 30 seconds

685

686

687

* Downlink Payload (prefix 0x01):

688

689

0x01 aa bb cc ~/~/ Same as AT+TDC=0x(aa bb cc)

690

691

692

==== Set Work Mode (AT+MOD) ====

Set work mode.

* AT Command:

AT+MOD=N

Example: AT+MOD=2. Set work mode to Double DI counting mode

701

702

703

* Downlink Payload (prefix 0x0A):

704

705

0x0A aa ~/~/ Same as AT+MOD=aa

==== Poll an uplink ====

* AT Command:

There is no AT Command to poll uplink

714

715

716

* Downlink Payload (prefix 0x08):

717

718

0x08 FF ~/~/ Poll an uplink,

719

720

Example: 0x08FF, ask device to send an Uplink

721

722

723

==== Enable Trigger Mode ====

724

725

Use of trigger mode, please check [[ADDMOD6>>path:#MOD6]]

* AT Command:

AT+ADDMOD6=1 or 0

1: Enable Trigger Mode

732

733

0: Disable Trigger Mode

734

735

736

* Downlink Payload (prefix 0x0A 06):

737

738

0x0A 06 aa ~/~/ Same as AT+ADDMOD6=aa,

739

740

741

==== Poll trigger settings ====

742

743

Poll trigger settings,

* AT Command:

There is no AT Command for this feature.

748

749

750

* Downlink Payload (prefix 0x AB 06):

751

752

0xAB 06 ~/~/ Poll trigger settings, device will uplink [[trigger settings>>path:#Trigger_Settings]] once receive this command

753

754

755

==== Enable / Disable DI1/DI2/DI3 as trigger ====

756

757

Enable Disable DI1/DI2/DI2 as trigger,

* AT Command:

Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >

Example:

AT+ DTRI =1,0 (Enable DI1 trigger / disable DI2 trigger)

* Downlink Payload (prefix 0xAA 02):

770

771

0xAA 02 aa bb ~/~/ Same as AT+DTRI=aa,bb

==== Trigger1 – Set DI1 or DI3 as trigger ====

776

777

Set DI1 or DI3(for LT-33222-L) trigger.

* AT Command:

AT+TRIG1=a,b

a : Interrupt mode. 0: falling edge; 1: rising edge, 2: falling and raising edge(for MOD=1).

b : delay timing.

Example:

AT+TRIG1=1,100(set DI1 port to trigger on high level, valid signal is 100ms )

790

791

792

* Downlink Payload (prefix 0x09 01 ):

793

794

0x09 01 aa bb cc ~/~/ same as AT+TRIG1=aa,0x(bb cc)

795

796

797

==== Trigger2 – Set DI2 as trigger ====

Set DI2 trigger.

* AT Command:

AT+TRIG2=a,b

a : Interrupt mode. 0: falling edge; 1: rising edge, 2: falling and raising edge(for MOD=1).

b : delay timing.

Example:

AT+TRIG2=0,100(set DI1 port to trigger on low level, valid signal is 100ms )

812

813

814

* Downlink Payload (prefix 0x09 02 ):

815

816

0x09 02 aa bb cc ~/~/ same as AT+TRIG1=aa,0x(bb cc)

817

818

819

==== Trigger – Set AC (current) as trigger ====

820

821

Set current trigger , base on AC port. See [[trigger mode>>path:#MOD6]]

* AT Command:

AT+ACLIM. See [[trigger mode>>path:#MOD6]]

826

827

828

* Downlink Payload (prefix 0xAA 01 ):

829

830

0x AA 01 aa bb cc dd ee ff gg hh ~/~/ same as AT+ACLIM See [[trigger mode>>path:#MOD6]]

831

832

833

==== Trigger – Set AV (voltage) as trigger ====

834

835

Set current trigger , base on AV port. See [[trigger mode>>path:#MOD6]]

* AT Command:

AT+AVLIM. See [[trigger mode>>path:#MOD6]]

840

841

842

* Downlink Payload (prefix 0xAA 00 ):

843

844

0x AA 00 aa bb cc dd ee ff gg hh ~/~/ same as AT+AVLIM See [[trigger mode>>path:#MOD6]]

845

846

==== Trigger – Set minimum interval ====

847

848

Set AV and AC trigger minimum interval, system won’t response to the second trigger within this set time after the first trigger.

* AT Command:

AT+ATDC=5. Device won’t response the second trigger within 5 minute after the first trigger.

853

854

855

* Downlink Payload (prefix 0xAC ):

856

857

0x AC aa bb ~/~/ same as AT+ATDC=0x(aa bb) . Unit (min)

858

859

860

==== DO ~-~- Control Digital Output DO1/DO2/DO3 ====

* AT Command:

There is no AT Command to control Digital Output

865

866

867

* Downlink Payload (prefix 0x02):

868

869

0x02 aa bb cc ~/~/ Set DO1/DO2/DO3 output

870

871

If payload = 0x02010001, while there is load between V+ and DOx, it means set DO1 to low, DO2 to high and DO3 to low.

872

873

01: Low, 00: High , 11: No action

874

875

(% border="1" style="background-color:#f7faff" %)

876

|Downlink Code|DO1|DO2|DO3

877

|02 01 00 11|Low|High|No Action

878

|02 00 11 01|High|No Action|Low

879

|02 11 01 00|No Action|Low|High

880

881

Note: For LT-22222-L, there is no DO3, the last byte can use any value.

882

883

Device will upload a packet if downlink code executes successfully.

==== DO ~-~- Control Digital Output DO1/DO2/DO3 with time control ====

* AT Command:

There is no AT Command to control Digital Output

894

895

896

* Downlink Payload (prefix 0xA9):

897

898

0xA9 aa bb cc ~/~/ Set DO1/DO2/DO3 output with time control

899

900

This is to control the digital output time of DO pin. Include four bytes:

901

902

**First Byte:** Type code (0xA9)

903

904

**Second Byte**: Inverter Mode

905

906

01: DO pins will change back to original state after timeout.

907

908

00: DO pins will change to an inverter state after timeout

909

910

911

**Third Byte**: Control Method and Ports status:

912

913

(% border="1" style="background-color:#f7faff" %)

914

|Second Byte|Status

915

|0x01|DO1 set to low

916

|0x00|DO1 set to high

917

|0x11|DO1 NO Action

918

919

**Fourth Byte**: Control Method and Ports status:

920

921

(% border="1" style="background-color:#f7faff" %)

922

|Second Byte|Status

923

|0x01|DO2 set to low

924

|0x00|DO2 set to high

925

|0x11|DO2 NO Action

926

927

**Fifth Byte**: Control Method and Ports status:

928

929

(% border="1" style="background-color:#f7faff" %)

930

|Second Byte|Status

931

|0x01|DO3 set to low

932

|0x00|DO3 set to high

933

|0x11|DO3 NO Action

934

935

**Sixth and Seventh Byte**:

936

937

Latching time. Unit: ms

938

939

Device will upload a packet if downlink code executes successfully.

Example payload:

1. A9 01 01 01 01 07 D0

946

947

DO1 pin & DO2 pin & DO3 pin will be set to Low, last 2 seconds, then change back to original state.

948

949

950

1. A9 01 00 01 11 07 D0

951

952

DO1 pin set high, DO2 pin set low, DO3 pin no action, last 2 seconds, then change back to original state.

953

954

955

1. A9 00 00 00 00 07 D0

956

957

DO1 pin & DO2 pin & DO3 pin will be set to high, last 2 seconds, then both change to low.

958

959

960

1. A9 00 11 01 00 07 D0

961

962

DO1 pin no action, DO2 pin set low, DO3 pin set high, last 2 seconds, then DO1 pin no action, DO2 pin set high, DO3 pin set low

==== Relay ~-~- Control Relay Output RO1/RO2 ====

* AT Command:

There is no AT Command to control Relay Output

972

973

974

* Downlink Payload (prefix 0x03):

975

976

0x03 aa bb ~/~/ Set RO1/RO2 output

977

978

If payload = 0x030100, it means set RO1 to close and RO2 to open.

979

980

01: Close , 00: Open , 11: No action

981

982

(% border="1" style="background-color:#f7faff" %)

983

|Downlink Code|RO1|RO2

984

|03 00 11|Open|No Action

985

|03 01 11|Close|No Action

986

|03 11 00|No Action|Open

987

|03 11 01|No Action|Close

988

|03 00 00|Open|Open

989

|03 01 01|Close|Close

|03 01 00|Close|Open

|03 00 01|Open|Close

Device will upload a packet if downlink code executes successfully.

994

995

996

==== Relay ~-~- Control Relay Output RO1/RO2 with time control ====

* AT Command:

There is no AT Command to control Relay Output

1001

1002

1003

* Downlink Payload (prefix 0x05):

1004

1005

0x05 aa bb cc dd ~/~/ Set RO1/RO2 relay with time control:

1006

1007

This is to control the relay output time of relay. Include four bytes:

1008

1009

**First Byte:** Type code (0x05)

1010

1011

**Second Byte(aa)**: Inverter Mode

1012

1013

01: Relays will change back to original state after timeout.

1014

1015

00: Relays will change to an inverter state after timeout

1016

1017

1018

**Third Byte(bb)**: Control Method and Ports status:

1019

1020

(% border="1" style="background-color:#f7faff" %)

1021

|Value|Status

1022

|0x11|RO1 and RO2 to NO

1023

|0x10|RO2 to NO, RO1 to NC

1024

|0x01|RO2 to NC, RO1 to NO

1025

|0x00|RO1 and RO2 to NC.

1026

|0x20|RO1 No Action, RO2 to NC

1027

|0x21|RO1 No Action, RO2 to NO

1028

|0x02|RO1 to NC, RO2 No Action

1029

|0x12|RO1 to NO, RO2 No Action

1030

1031

**Fourth / Fifth Bytes (cc)**: Latching time. Unit: ms

1032

1033

Device will upload a packet if downlink code executes successfully.

**Example payload:**

1. 05 01 11 07 D0

Relay1 and Relay 2 will be set to NO , last 2 seconds, then change back to original state.

1. 05 01 10 07 D0

Relay1 will change to NO, Relay2 will change to NC, last 2 seconds, then both change back to original state.

1. 05 00 01 07 D0

Relay1 will change to NC, Relay2 will change to NO, last 2 seconds, then relay change to NO, Relay2 change to NC.

1. 05 00 00 07 D0

Relay 1 & relay2 will change to NC, last 2 seconds, then both change to NO.

==== Counting ~-~- Voltage threshold counting ====

1064

1065

When voltage exceed the threshold, count. Feature see [[MOD4>>path:#MOD4]]

* AT Command:

AT+VOLMAX ~/~/ See [[MOD4>>path:#MOD4]]

1070

1071

1072

* Downlink Payload (prefix 0xA5):

1073

1074

0xA5 aa bb cc ~/~/ Same as AT+VOLMAX=(aa bb),cc

1075

1076

1077

==== Counting ~-~- Pre-configure the Count Number ====

* AT Command:

AT+SETCNT=aa,(bb cc dd ee)

aa: 1: Set count1,

2: Set count2,

3: Set AV1 count

Bb cc dd ee: number to be set

1090

1091

1092

* Downlink Payload (prefix 0xA8):

1093

1094

0x A8 aa bb cc dd ee ~/~/ same as AT+SETCNT=aa,(bb cc dd ee)

==== Counting ~-~- Clear Counting ====

1101

1102

Clear counting for counting mode

* AT Command:

AT+CLRCOUNT ~/~/ clear all counting

1107

1108

1109

* Downlink Payload (prefix 0xA6):

1110

1111

0x A6 01 ~/~/ clear all counting,

==== Counting ~-~- Change counting mode save time ====

* AT Command:

AT+COUTIME=60 ~/~/ Set save time to 60 seconds. Device will save the counting result in internal flash every 60 seconds. (min value: 30)

1121

1122

1123

* Downlink Payload (prefix 0xA7):

1124

1125

0x A7 aa bb cc ~/~/ same as AT+COUTIME =aa bb cc,

1126

1127

range: aa bb cc:0 to 16777215, (unit:second)

1.

11. Integrate with Mydevice

1134

1135

Mydevices provides a human friendly interface to show the sensor data, once we have data in TTN, we can use Mydevices to connect to TTN and see the data in Mydevices. Below are the steps:

1136

1137

1138

Step 1: Be sure that your device is programmed and properly connected to the network at this time.

1139

1140

Step 2: To configure the Application to forward data to Mydevices you will need to add integration. To add the Mydevices integration, perform the following steps:

1141

1142

1143

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image010.png]]

1144

1145

1146

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image011.png]]

1147

1148

1149

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image012.png]]

Step 3: Create an account or log in Mydevices.

1154

1155

Step 4: Search LT-22222-L(for both LT-22222-L / LT-33222-L) and add DevEUI.

1156

1157

Search under The things network

1158

1159

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image013.png]]

1160

1161

1162

After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.

1163

1164

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image014.png]]

1165

1166

1167

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.png]]

1168

1169

1170

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image016.png]]

1171

1172

1173

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.png]]

1174

1175

1176

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image018.png]]

1.

11. Interface Detail

111. Digital Input Port: DI1/DI2 /DI3 ( For LT-33222-L, low active )

1182

1183

Support NPN Type sensor

1184

1185

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image019.png]]

1.

11.

111. Digital Input Port: DI1/DI2 ( For LT-22222-L)

1192

1193

The DI port of LT-22222-L can support NPN or PNP output sensor.

1194

1195

Internal circuit as below, the NEC2501 is a photocoupler, the Active current (from NEC2501 pin 1 to pin 2 is 1ma and the max current is 50mA. When there is active current pass NEC2501 pin1 to pin2. The DI will be active high

1196

1197

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image020.png]]

1198

1199

When use need to connect a device to the DI port, both DI1+ and DI1- must be connected.

1200

1201

1202

**Example1**: Connect to a Low active sensor.

1203

1204

This type of sensor will output a low signal GND when active.

1205

1206

* Connect sensor’s output to DI1-

1207

* Connect sensor’s VCC to DI1+.

1208

1209

So when sensor active, the current between NEC2501 pin1 and pin2 is:

1210

1211

//IF//[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]] = DI1+ / 1K.

1212

1213

If DI1+ = 12v, the //IF//[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]] = 12mA , So the LT-22222-L will be able to detect this active signal.

1214

1215

1216

**Example2**: Connect to a High active sensor.

1217

1218

This type of sensor will output a high signal (example 24v) when active.

1219

1220

* Connect sensor’s output to DI1+

1221

* Connect sensor’s GND DI1-.

1222

1223

So when sensor active, the current between NEC2501 pin1 and pin2 is:

1224

1225

//IF//[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]] = DI1+ / 1K.

1226

1227

If DI1+ = 24v, the //IF//[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]] = 24mA , So the LT-22222-L will be able to detect this high active signal.

1228

1229

1230

**Example3**: Connect to a 220v high active sensor.公司测试一下

1231

1232

Assume user want to monitor an active signal higher than 220v, to make sure not burn the photocoupler

1233

1234

* Connect sensor’s output to DI1+ with a serial 50K resistor

1235

* Connect sensor’s GND DI1-.

1236

1237

So when sensor active, the current between NEC2501 pin1 and pin2 is:

1238

1239

//IF//[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png]] = DI1+ / 51K.

1240

1241

If sensor output is 220v, the //IF//[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png]] = 4.3mA , So the LT-22222-L will be able to detect this high active signal safely.

1.

11.

111. Digital Output Port: DO1/DO2 /DO3

1247

1248

NPN output: GND or Float. Max voltage can apply to output pin is 36v.

1249

1250

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png]]

1.

11.

111. Analog Input Interface

1258

1259

The analog input interface is as below. The LT will measure the IN2 voltage so to calculate the current pass the Load. The formula is:

1260

1261

AC2 = (IN2 voltage )/12

1262

1263

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image024.png]]

Example to connect a 4~~20mA sensor

1268

1269

We take the wind speed sensor as an example for reference only.

1270

1271

Specifications of the wind speed sensor:

Red:12~~24v

Yellow:4~~20mA

Black:GND

Connection diagram:

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.jpg]]

1283

1284

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image026.png]]

1.

11.

111. Relay Output

The LT serial controller has two relay interfaces; each interface uses two pins of the screw terminal. User can connect other device’s Power Line to in serial of RO1_1 and RO_2. Such as below:

1293

1294

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image027.png]]

1295

1296

1297

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image028.png]]

1.

11. LEDs Indicators

(% border="1" style="background-color:#f7faff" %)

1307

|**LEDs**|**Feature**

1308

|**PWR**|Always on if there is power

1309

|**SYS**|After device is powered on, the SYS will **fast blink in GREEN** for 5 times, means RS485-LN start to join LoRaWAN network. If join success, SYS will be **on GREEN for 5 seconds. **SYS will **blink Blue** on every upload and **blink Green** once receive a downlink message.

1310

|**TX**|(((

1311

Device boot: TX blinks 5 times.

1312

1313

Successful join network: TX ON for 5 seconds.

1314

1315

Transmit a LoRa packet: TX blinks once

1316

)))

1317

|**RX**|RX blinks once when receive a packet.

|**DO1**|

|**DO2**|

|**DO3**|

|**DI2**|(((

For LT-22222-L: ON when DI2 is high, LOW when DI2 is low

1323

1324

For LT-33222-L: ON when DI2 is low, LOW when DI2 is high

1325

)))

1326

|**DI2**|(((

1327

For LT-22222-L: ON when DI2 is high, LOW when DI2 is low

1328

1329

For LT-33222-L: ON when DI2 is low, LOW when DI2 is high

1330

)))

1331

|**DI3**|For LT-33222-L ONLY: ON when DI3 is low, LOW when DI3 is high

1332

|**DI2**|(((

1333

For LT-22222-L: ON when DI2 is high, LOW when DI2 is low

1334

1335

For LT-33222-L: ON when DI2 is low, LOW when DI2 is high

)))

|**RO1**|

|**RO2**|

1. Use AT Command

11. Access AT Command

1342

1343

LT supports AT Command set. User can use a USB to TTL adapter plus the 3.5mm Program Cable to connect to LT for using AT command, as below.

1344

1345

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]

1346

1347

1348

In PC, User needs to set **serial tool**(such as [[putty>>url:https://www.chiark.greenend.org.uk/~~sgtatham/putty/latest.html]], SecureCRT) baud rate to **9600** to access to access serial console for LT. The AT commands are disable by default and need to enter password (default:**123456**) to active it. As shown below:

1349

1350

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]]

1351

1352

1353

More detail AT Command manual can be found at [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/]]

1354

1355

AT+<CMD>? : Help on <CMD>

AT+<CMD> : Run <CMD>

AT+<CMD>=<value> : Set the value

1360

1361

AT+<CMD>=? : Get the value

1362

1363

ATZ: Trig a reset of the MCU

1364

1365

AT+FDR: Reset Parameters to Factory Default, Keys Reserve

1366

1367

AT+DEUI: Get or Set the Device EUI

1368

1369

AT+DADDR: Get or Set the Device Address

1370

1371

AT+APPKEY: Get or Set the Application Key

1372

1373

AT+NWKSKEY: Get or Set the Network Session Key

1374

1375

AT+APPSKEY: Get or Set the Application Session Key

1376

1377

AT+APPEUI: Get or Set the Application EUI

1378

1379

AT+ADR: Get or Set the Adaptive Data Rate setting. (0: off, 1: on)

1380

1381

AT+TXP: Get or Set the Transmit Power (0-5, MAX:0, MIN:5, according to LoRaWAN Spec)

1382

1383

AT+DR: Get or Set the Data Rate. (0-7 corresponding to DR_X)

1384

1385

AT+DCS: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing

1386

1387

AT+PNM: Get or Set the public network mode. (0: off, 1: on)

1388

1389

AT+RX2FQ: Get or Set the Rx2 window frequency

1390

1391

AT+RX2DR: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)

1392

1393

AT+RX1DL: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms

1394

1395

AT+RX2DL: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms

1396

1397

AT+JN1DL: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms

1398

1399

AT+JN2DL: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms

1400

1401

AT+NJM: Get or Set the Network Join Mode. (0: ABP, 1: OTAA)

1402

1403

AT+NWKID: Get or Set the Network ID

1404

1405

AT+FCU: Get or Set the Frame Counter Uplink

1406

1407

AT+FCD: Get or Set the Frame Counter Downlink

1408

1409

AT+CLASS: Get or Set the Device Class

1410

1411

AT+JOIN: Join network

1412

1413

AT+NJS: Get OTAA Join Status

1414

1415

AT+SENDB: Send hexadecimal data along with the application port

1416

1417

AT+SEND: Send text data along with the application port

1418

1419

AT+RECVB: Print last received data in binary format (with hexadecimal values)

1420

1421

AT+RECV: Print last received data in raw format

1422

1423

AT+VER: Get current image version and Frequency Band

1424

1425

AT+CFM: Get or Set the confirmation mode (0-1)

1426

1427

AT+CFS: Get confirmation status of the last AT+SEND (0-1)

1428

1429

AT+SNR: Get the SNR of the last received packet

1430

1431

AT+RSSI: Get the RSSI of the last received packet

1432

1433

AT+TDC: Get or set the application data transmission interval in ms

1434

1435

AT+PORT: Get or set the application port

1436

1437

AT+DISAT: Disable AT commands

1438

1439

AT+PWORD: Set password, max 9 digits

1440

1441

AT+CHS: Get or Set Frequency (Unit: Hz) for Single Channel Mode

1442

1443

AT+CHE: Get or Set eight channels mode, Only for US915, AU915, CN470

1444

1445

AT+CFG: Print all settings

1.

11. Common AT Command Sequence

1451

111. Multi-channel ABP mode (Use with SX1301/LG308)

1452

1453

If device has not joined network yet:

123456

AT+FDR

123456

AT+NJM=0

ATZ

If device already joined network:

AT+NJM=0

ATZ

1.

11.

111. Single-channel ABP mode (Use with LG01/LG02)

1475

1476

123456 Enter Password to have AT access.

1477

1478

AT+FDR Reset Parameters to Factory Default, Keys Reserve

1479

1480

123456 Enter Password to have AT access.

1481

1482

AT+CLASS=C Set to work in CLASS C

1483

1484

AT+NJM=0 Set to ABP mode

1485

1486

AT+ADR=0 Set the Adaptive Data Rate Off

1487

1488

AT+DR=5 Set Data Rate

1489

1490

AT+TDC=60000 Set transmit interval to 60 seconds

1491

1492

AT+CHS=868400000 Set transmit frequency to 868.4Mhz

1493

1494

AT+RX2FQ=868400000 Set RX2Frequency to 868.4Mhz (according to the result from server)

1495

1496

AT+RX2DR=5 Set RX2DR to match the downlink DR from server. see below

1497

1498

AT+DADDR=26 01 1A F1 Set Device Address to 26 01 1A F1, this ID can be found in the LoRa Server portal.

ATZ Reset MCU

**Note:**

1. Make sure the device is set to ABP mode in the IoT Server.

1505

1. Make sure the LG01/02 gateway RX frequency is exactly the same as AT+CHS setting.

1506

1. Make sure SF / bandwidth setting in LG01/LG02 match the settings of AT+DR. refer [[this link>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_Gateway/&file=LoRaWAN%201.0.3%20Regional%20Parameters.xlsx]] to see what DR means.

1507

1. The command AT+RX2FQ and AT+RX2DR is to let downlink work. to set the correct parameters, user can check the actually downlink parameters to be used. As below. Which shows the RX2FQ should use 868400000 and RX2DR should be 5

1508

1509

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]]

1.

11.

111. Change to Class A

If sensor JOINED

AT+CLASS=A

ATZ

1. FAQ

1.

11. How to upgrade the image?

1530

1531

The LT LoRaWAN Controller is shipped with a 3.5mm cable, the cable is used to upload image to LT to:

1532

1533

* Support new features

1534

* For bug fix

1535

* Change LoRaWAN bands.

1536

1537

Below shows the hardware connection for how to upload an image to the LT:

1538

1539

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]

1540

1541

1542

**Step1:** Download [[flash loader>>url:https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/flasher-stm32.html]].

1543

1544

**Step2**: Download the [[LT Image files>>url:http://www.dragino.com/downloads/index.php?dir=LT_LoRa_IO_Controller/LT33222-L/image/]].

1545

1546

**Step3: **Open flashloader; choose the correct COM port to update.

**For LT-33222-L**:

Hold down the PRO button and then momentarily press the RST reset button and the **DO2 led** will change from OFF to ON. When **DO2 LED** is on, it means the device is in download mode.

**For LT-22222-L**:

Hold down the PRO button and then momentarily press the RST reset button and the **DO1 led** will change from OFF to ON. When **DO1 LED** is on, it means the device is in download mode.

|(((

Board detected

)))

|(((

)))

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image032.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.png]]

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image035.png]]

1571

1572

1573

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image037.png]]

1574

1575

1576

**Notice**: In case user has lost the program cable. User can hand made one from a 3.5mm cable. The pin mapping is:

1577

1578

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image038.png]]

1.

11. How to change the LoRa Frequency Bands/Region?

1583

1584

User can follow the introduction for [[how to upgrade image>>path:#upgrade_image]]. When download the images, choose the required image file for download.

1.

11. How to set up LT to work with Single Channel Gateway such as LG01/LG02?

1589

1590

In this case, users need to set LT-33222-L to work in ABP mode & transmit in only one frequency.

1591

1592

Assume we have a LG02 working in the frequency 868400000 now , below is the step.

1593

1594

1595

**Step1**: Log in TTN, Create an ABP device in the application and input the network session key (NETSKEY), app session key (APPSKEY) from the device.

1596

1597

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image039.png]]

1598

1599

Note: user just need to make sure above three keys match, User can change either in TTN or Device to make then match. In TTN, NETSKEY and APPSKEY can be configured by user in setting page, but Device Addr is generated by TTN.

1600

1601

1602

**Step2: **Run AT Command to make LT work in Single frequency & ABP mode. Below is the AT commands:

1603

1604

123456 Enter Password to have AT access.

1605

1606

AT+FDR Reset Parameters to Factory Default, Keys Reserve

1607

1608

123456 Enter Password to have AT access.

1609

1610

AT+NJM=0 Set to ABP mode

1611

1612

AT+ADR=0 Set the Adaptive Data Rate Off

1613

1614

AT+DR=5 Set Data Rate (Set AT+DR=3 for 915 band)

1615

1616

AT+TDC=60000 Set transmit interval to 60 seconds

1617

1618

AT+CHS=868400000 Set transmit frequency to 868.4Mhz

1619

1620

AT+DADDR=26 01 1A F1 Set Device Address to 26 01 1A F1

ATZ Reset MCU

As shown in below:

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image040.png]]

1.

11. Can I see counting event in Serial?

1632

1633

User can run AT+DEBUG command to see the counting event in serial. If firmware too old and doesn’t support AT+DEBUG. User can update to latest firmware first.

1. Trouble Shooting

11. Downlink doesn’t work, how to solve it?

1640

1641

Please see this link for how to debug:

1642

1643

[[http:~~/~~/wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#How_it_work>>url:http://wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#How_it_work]]

1.

11. Have trouble to upload image.

1648

1649

See this link for trouble shooting:

1650

1651

[[http:~~/~~/wiki.dragino.com/index.php?title=Firmware_Upgrade_Trouble_Shooting#UART_upgrade_trouble_shooting>>url:http://wiki.dragino.com/index.php?title=Firmware_Upgrade_Trouble_Shooting#UART_upgrade_trouble_shooting]]

1.

11. Why I can’t join TTN in US915 /AU915 bands?

1656

1657

It might be about the channels mapping. Please see this link for detail:

1658

1659

[[http:~~/~~/wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band>>url:http://wiki.dragino.com/index.php?title=LoRaWAN_Communication_Debug#Notice_of_US915.2FCN470.2FAU915_Frequency_band]]

1. Order Info

**For LT-33222-L-XXX or LT-22222-L-XXX:**

**XXX:**

* **EU433**: LT with frequency bands EU433

1671

* **EU868**: LT with frequency bands EU868

1672

* **KR920**: LT with frequency bands KR920

1673

* **CN470**: LT with frequency bands CN470

1674

* **AS923**: LT with frequency bands AS923

1675

* **AU915**: LT with frequency bands AU915

1676

* **US915**: LT with frequency bands US915

1677

* **IN865**: LT with frequency bands IN865

1678

* **CN779**: LT with frequency bands CN779

1. Packing Info

**Package Includes**:

1683

1684

* LT I/O Controller x 1

1685

* Stick Antenna for LoRa RF part x 1

1686

* Bracket for controller x1

1687

* Program cable x 1

1688

1689

**Dimension and weight**:

1690

1691

* Device Size: 13.5 x 7 x 3 cm

1692

* Device Weight: 105g

1693

* Package Size / pcs : 14.5 x 8 x 5 cm

1694

* Weight / pcs : 170g

1. Support

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1699

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to

1700

1701

[[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]

Wiki source code of LT-22222-L LoRa IO Controller User Manual

Applications

Navigation