Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -413,6 +413,8 @@
413	413	[[image:image-20220523181246-5.png]]
414	414
415	415	(((
	416	+
	417	+
416	416	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
417	417	)))
418	418
...	...	@@ -426,6 +426,7 @@
426	426	(% style="color:red" %)Note: DO3 is not valid for LT-22222-L.
427	427	)))
428	428
	431	+
429	429	(((
430	430	**To use counting mode, please run:**
431	431	)))
...	...	@@ -558,8 +558,8 @@
558	558
559	559	For example, if user has configured below commands:
560	560
561		-* **AT+MOD=1 ** **~-~->** The normal working mode
562		-* **AT+ADDMOD6=1**   **~-~->** Enable trigger
	564	+* **AT+MOD=1 ** **~-~->**  The normal working mode
	565	+* **AT+ADDMOD6=1**   **~-~->**  Enable trigger
563	563
564	564	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
565	565
...	...	@@ -566,8 +566,10 @@
566	566	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
567	567	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
568	568
	572	+
569	569	(% style="color:#037691" %)**AT Command to set Trigger Condition**:
570	570
	575	+
571	571	(% style="color:#4f81bd" %)**Trigger base on voltage**:
572	572
573	573	Format: AT+AVLIM=<AV1_LIMIT_LOW>,< AV1_LIMIT_HIGH>,<AV2_LIMIT_LOW>,< AV2_LIMIT_HIGH>
...	...	@@ -707,6 +707,8 @@
707	707
708	708	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
709	709
	715	+
	716	+
710	710	=== 3.4.1 Common Commands ===
711	711
712	712	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
...	...	@@ -715,6 +715,7 @@
715	715
716	716	=== 3.4.2 Sensor related commands ===
717	717
	725	+
718	718	==== 3.4.2.1 Set Transmit Interval ====
719	719
720	720	Set device uplink interval.
...	...	@@ -768,6 +768,7 @@
768	768
769	769
770	770
	779	+
771	771	==== 3.4.2.4 Enable Trigger Mode ====
772	772
773	773	Use of trigger mode, please check [[ADDMOD6>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
...	...	@@ -924,6 +924,7 @@
924	924
925	925
926	926
	936	+
927	927	==== 3.4.2.12 DO ~-~- Control Digital Output DO1/DO2/DO3 ====
928	928
929	929	* (% style="color:#037691" %)**AT Command**