Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Last modified by Saxer Lin on 2025/04/15 17:24

From version < 83.11 >

edited by Xiaoling
on 2022/06/29 17:35

To version < 82.37 >

edited by Xiaoling
on 2022/06/20 13:59

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -1,6 +1,7 @@
  (% style="text-align:center" %)
  [[image:image-20220523163353-1.jpeg||height="604" width="500"]]
++**LT-22222-L LoRa IO Controller User Manual **
  **Table of Contents:**
@@ -166,6 +166,7 @@
  Packet engine up to 256 bytes with CRC.
++
  )))
@@ -201,6 +201,8 @@
  * 1 x Counting Port
  )))
++
++
  = 2. Power ON Device =
  The LT controller can be powered by 7 ~~ 24V DC power source. Connect VIN to Power Input V+ and GND to power input V- to power the LT controller.
@@ -218,11 +218,11 @@
  == 3.1 How it works? ==
  (((
--The LT is configured as LoRaWAN OTAA Class C mode by default. It has OTAA keys to join network. To connect a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the LT. It will auto join the network via OTAA. For LT-22222-L, the LED will show the Join status: After power on (% style="color:green" %)**TX LED**(%%) will fast blink 5 times, LT-22222-L will enter working mode and start to JOIN LoRaWAN network. (% style="color:green" %)**TX LED**(%%) will be on for 5 seconds after joined in network. When there is message from server, the RX LED will be on for 1 second.
++The LT is configured as LoRaWAN OTAA Class C mode by default. It has OTAA keys to join network. To connect a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the LT. It will auto join the network via OTAA. For LT-22222-L, the LED will show the Join status: After power on **TX LED** will fast blink 5 times, LT-22222-L will enter working mode and start to JOIN LoRaWAN network. **TX LED** will be on for 5 seconds after joined in network. When there is message from server, the **RX LED** will be on for 1 second.
  )))
  (((
--In case user can't set the OTAA keys in the network server and has to use the existing keys from server. User can [[use AT Command>>||anchor="H4.UseATCommand"]] to set the keys in the devices.
++In case user can’t set the OTAA keys in the network server and has to use the existing keys from server. User can [[use AT Command>>||anchor="H4.UseATCommand"]] to set the keys in the devices.
  )))
@@ -274,15 +274,13 @@
  There are five working modes + one interrupt mode on LT for different type application:
--* (% style="color:blue" %)**MOD1**(%%): (default setting): 2 x ACI + 2AVI + DI + DO + RO
--* (% style="color:blue" %)**MOD2**(%%): Double DI Counting + DO + RO
--* (% style="color:blue" %)**MOD3**(%%): Single DI Counting + 2 x ACI + DO + RO
--* (% style="color:blue" %)**MOD4**(%%): Single DI Counting + 1 x Voltage Counting + DO + RO
--* (% style="color:blue" %)**MOD5**(%%): Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
--* (% style="color:blue" %)**ADDMOD6**(%%): Trigger Mode, Optional, used together with MOD1 ~~ MOD5
++* **MOD1**: (default setting): 2 x ACI + 2AVI + DI + DO + RO
++* **MOD2**: Double DI Counting + DO + RO
++* **MOD3**: Single DI Counting + 2 x ACI + DO + RO
++* **MOD4**: Single DI Counting + 1 x Voltage Counting + DO + RO
++* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
++* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
--
--
  === 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
  The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
@@ -321,8 +321,6 @@
  * [1] RO1 relay channel is close and the RO1 LED is ON.
  * [0] RO2 relay channel is open and RO2 LED is OFF;
--
--
  **LT22222-L:**
  * [1] DI2 channel is high input and DI2 LED is ON;
@@ -338,8 +338,6 @@
  ** DO1 is high in case there is load between DO1 and V+.
  ** DO1 LED is off in both case
--
--
  === 3.3.2 AT+MOD~=2, (Double DI Counting) ===
@@ -413,8 +413,6 @@
  [[image:image-20220523181246-5.png]]
  (((
--
--
  (% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
  )))
@@ -428,7 +428,6 @@
  (% style="color:red" %)Note: DO3 is not valid for LT-22222-L.
  )))
--
  (((
  **To use counting mode, please run:**
  )))
@@ -561,8 +561,8 @@
  For example, if user has configured below commands:
--* **AT+MOD=1 **            **~-~->**   The normal working mode
--* **AT+ADDMOD6=1**   **~-~->**   Enable trigger
++* **AT+MOD=1 **  **~-~->** The normal working mode
++* **AT+ADDMOD6=1**   **~-~->** Enable trigger
  LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
@@ -572,7 +572,6 @@
  (% style="color:#037691" %)**AT Command to set Trigger Condition**:
--
  (% style="color:#4f81bd" %)**Trigger base on voltage**:
  Format: AT+AVLIM=<AV1_LIMIT_LOW>,< AV1_LIMIT_HIGH>,<AV2_LIMIT_LOW>,< AV2_LIMIT_HIGH>
@@ -712,8 +712,6 @@
  * (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
--
--
  === 3.4.1 Common Commands ===
  They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
@@ -722,7 +722,6 @@
  === 3.4.2 Sensor related commands ===
--
  ==== 3.4.2.1 Set Transmit Interval ====
  Set device uplink interval.
@@ -776,7 +776,6 @@
--
  ==== 3.4.2.4 Enable Trigger Mode ====
  Use of trigger mode, please check [[ADDMOD6>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
@@ -808,7 +808,7 @@
  * (% style="color:#037691" %)**Downlink Payload (prefix 0x AB 06):**
--**0xAB 06         **~/~/ Poll trigger settings, device will uplink trigger settings once receive this command
++**0xAB 06         **~/~/ Poll trigger settings, device will uplink trigger settings once receive this command
@@ -854,6 +854,9 @@
  * (% style="color:#037691" %)**Downlink Payload (prefix 0x09 01 ):**
  * **0x09 01 aa bb cc    **     ~/~/ same as AT+TRIG1=aa,0x(bb cc)
++
++
++
  ==== 3.4.2.8 Trigger2 – Set DI2 as trigger ====
  Set DI2 trigger.
@@ -918,7 +918,7 @@
  * (% style="color:#037691" %)**AT Command**
--**AT+ATDC=5        ** Device won't response the second trigger within 5 minute after the first trigger.
++**AT+ATDC=5        ** Device won't response the second trigger within 5 minute after the first trigger.
  * (% style="color:#037691" %)**Downlink Payload (prefix 0xAC )**
@@ -925,15 +925,9 @@
  **0x AC aa bb   ** ~/~/ same as AT+ATDC=0x(aa bb)   . Unit (min)
--(((
--
--(% style="color:red" %)Note: ATDC setting must be more than 5min
--)))
--
--
  ==== 3.4.2.12 DO ~-~- Control Digital Output DO1/DO2/DO3 ====
  * (% style="color:#037691" %)**AT Command**
@@ -1158,7 +1158,7 @@
  * (% style="color:#037691" %)**AT Command:**
--**AT+CLRCOUNT ** ~/~/ clear all counting
++(% style="color:#037691" %)(%%)**AT+CLRCOUNT ** ~/~/ clear all counting
  * (% style="color:#037691" %)**Downlink Payload (prefix 0xA6):**
@@ -1920,8 +1920,10 @@
  )))
++
  = 7. Order Info =
++
  (% style="color:#4f81bd" %)**LT-22222-L-XXX:**
@@ -1937,6 +1937,9 @@
  * (% style="color:#4f81bd" %)**IN865**(%%): LT with frequency bands IN865
  * (% style="color:#4f81bd" %)**CN779**(%%): LT with frequency bands CN779
++
++
++
  = 8. Packing Info =
@@ -1954,6 +1954,9 @@
  * Package Size / pcs : 14.5 x 8 x 5 cm
  * Weight / pcs : 170g
++
++
++
  = 9. Support =
  * (((

Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Summary

Details

Applications

Navigation