Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -19,8 +19,6 @@
19	19	== 1.1 What is LT Series I/O Controller ==
20	20
21	21	(((
22		-
23		-
24	24	The Dragino (% style="color:blue" %)**LT series I/O Modules**(%%) are Long Range LoRaWAN I/O Controller. It contains different I/O Interfaces such as:** (% style="color:blue" %)analog current Input, analog voltage input(%%)**(% style="color:blue" %), **relay output**, **digital input**(%%) and (% style="color:blue" %)**digital output**(%%) etc. The LT I/O Modules are designed to simplify the installation of I/O monitoring.
25	25	)))
26	26
...	...	@@ -165,11 +165,10 @@
165	165	)))
166	166	* (((
167	167	Packet engine up to 256 bytes with CRC.
	166	+)))
168	168
169	169
170	170
171		-
172		-)))
173	173
174	174	== 1.3 Features ==
175	175
...	...	@@ -211,6 +211,7 @@
211	211
212	212
213	213
	211	+
214	214	= 2. Power ON Device =
215	215
216	216	The LT controller can be powered by 7 ~~ 24V DC power source. Connect VIN to Power Input V+ and GND to power input V- to power the LT controller.
...	...	@@ -291,9 +291,6 @@
291	291	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
292	292	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
293	293
294		-
295		-
296		-
297	297	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
298	298
299	299	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -784,6 +784,7 @@
784	784
785	785	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
786	786
	782	+
787	787	=== 3.4.1 Common Commands ===
788	788
789	789	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
...	...	@@ -2015,16 +2015,8 @@
2015	2015	)))
2016	2016
2017	2017	(((
2018		-== 5.6 Why does the relay output become the default and open relay after the lt22222 is powered off? ==
	2014	+
2019	2019
2020		-If the device is not shut down, but directly powered off.
2021		-
2022		-It will default that this is a power-off state.
2023		-
2024		-In modes 2 to 5, DO RO status and pulse count are saved in flash.
2025		-
2026		-After restart, the status before power failure will be read from flash.
2027		-
2028	2028	= 6. Trouble Shooting =
2029	2029	)))
2030	2030