Changes for page LT-22222-L -- LoRa I/O Controller User Manual

Last modified by Mengting Qiu on 2025/06/04 18:42

From 82.11 to 82.10 From 82.33 to 82.32

From version 82.32

edited by Xiaoling
on 2022/06/20 13:36

Change comment: There is no comment for this version

To version 82.11

edited by Xiaoling
on 2022/06/20 11:43

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -181,6 +181,8 @@
  * Firmware upgradable via program port
  * Counting
++
++
  == 1.4  Applications ==
  * Smart Buildings & Home Automation
@@ -190,6 +190,8 @@
  * Smart Cities
  * Smart Factory
++
++
  == 1.5 Hardware Variants ==
  (% border="1" style="background-color:#f7faff; width:500px" %)
@@ -204,7 +204,6 @@
  )))
--
  = 2. Power ON Device =
  The LT controller can be powered by 7 ~~ 24V DC power source. Connect VIN to Power Input V+ and GND to power input V- to power the LT controller.
@@ -285,6 +285,8 @@
  * **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
  * **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
++
++
  === 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
  The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
@@ -338,6 +338,8 @@
  ** DO1 is high in case there is load between DO1 and V+.
  ** DO1 LED is off in both case
++
++
  === 3.3.2 AT+MOD~=2, (Double DI Counting) ===
@@ -387,20 +387,24 @@
  (((
  **For LT22222-L:**
++)))
++(% class="box infomessage" %)
++(((
++(((
++**AT+TRIG1=0,100 (set DI1 port to trigger on low level, valid signal is 100ms) **
--(% style="color:blue" %)**AT+TRIG1=0,100**(%%)**    (set DI1 port to trigger on low level, valid signal is 100ms) **
++**AT+TRIG1=1,100(set DI1 port to trigger on high level, valid signal is 100ms ) **
--(% style="color:blue" %)**AT+TRIG1=1,100**(%%)**    (set DI1 port to trigger on high level, valid signal is 100ms ) **
++**AT+TRIG2=0,100 (set DI2 port to trigger on low level, valid signal is 100ms) **
--(% style="color:blue" %)**AT+TRIG2=0,100**(%%)**    (set DI2 port to trigger on low level, valid signal is 100ms) **
++**AT+TRIG2=1,100 (set DI2 port to trigger on high level, valid signal is 100ms ) **
--(% style="color:blue" %)**AT+TRIG2=1,100**(%%)**    (set DI2 port to trigger on high level, valid signal is 100ms ) **
++**AT+SETCNT=1,60   (Set COUNT1 value to 60)**
--(% style="color:blue" %)**AT+SETCNT=1,60**(%%)**   (Set COUNT1 value to 60)**
--
--(% style="color:blue" %)**AT+SETCNT=2,60**(%%)**   (Set COUNT2 value to 60)**
++**AT+SETCNT=2,60   (Set COUNT2 value to 60)**
  )))
++)))
@@ -492,19 +492,22 @@
  **Plus below command for AVI1 Counting:**
++)))
++(% class="box infomessage" %)
++(((
++(((
++(% style="color:blue" %)**AT+SETCNT=3,60**(%%)**   (set AVI Count to 60)**
--(% style="color:blue" %)**AT+SETCNT=3,60**(%%)**            (set AVI Count to 60)**
++(% style="color:blue" %)**AT+VOLMAX=20000**(%%)**   (If AVI1 voltage higher than VOLMAX (20000mV =20v), counter increase 1)**
--(% style="color:blue" %)**AT+VOLMAX=20000**(%%)**       (If AVI1 voltage higher than VOLMAX (20000mV =20v), counter increase 1)**
++(% style="color:blue" %)**AT+VOLMAX=20000,0**(%%)**   (If AVI1 voltage lower than VOLMAX (20000mV =20v), counter increase 1)**
--(% style="color:blue" %)**AT+VOLMAX=20000,0**(%%)**    (If AVI1 voltage lower than VOLMAX (20000mV =20v), counter increase 1)**
--
--(% style="color:blue" %)**AT+VOLMAX=20000,1**(%%)**    (If AVI1 voltage higer than VOLMAX (20000mV =20v), counter increase 1)**
++(% style="color:blue" %)**AT+VOLMAX=20000,1**(%%)**   (If AVI1 voltage higer than VOLMAX (20000mV =20v), counter increase 1)**
  )))
++)))
--
  === 3.3.5 AT+MOD~=5, Single DI Counting + 2 x AVI + 1 x ACI ===
@@ -564,7 +564,6 @@
 . Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
 . Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
--
  (% style="color:#037691" %)**AT Command to set Trigger Condition**:
  (% style="color:#4f81bd" %)**Trigger base on voltage**:
@@ -706,6 +706,8 @@
  * (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
++
++
  === 3.4.1 Common Commands ===
  They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
@@ -720,19 +720,23 @@
  * (% style="color:#037691" %)**AT Command:**
++(% class="box infomessage" %)
++(((
  **AT+TDC=N **
++)))
--
  **Example: **AT+TDC=30000. Means set interval to 30 seconds
  * (% style="color:#037691" %)**Downlink Payload (prefix 0x01):**
++(% class="box infomessage" %)
++(((
  **0x01 aa bb cc     ~/~/ Same as AT+TDC=0x(aa bb cc)**
++)))
--
  ==== 3.4.2.2 Set Work Mode (AT+MOD) ====
  Set work mode.
@@ -739,29 +739,36 @@
  * (% style="color:#037691" %)**AT Command:**
++(% class="box infomessage" %)
++(((
  **AT+MOD=N  **
++)))
--
  **Example**: AT+MOD=2. Set work mode to Double DI counting mode
  * (% style="color:#037691" %)**Downlink Payload (prefix 0x0A):**
--(% style="color:#037691" %)****(%%)**0x0A aa    ** ~/~/ Same as AT+MOD=aa
++(% class="box infomessage" %)
++(((
++**0x0A aa     ~/~/ Same as AT+MOD=aa**
++)))
--
  ==== 3.4.2.3 Poll an uplink ====
--* (% style="color:#037691" %)**AT Command:**
++* (% style="color:#037691" %)AT Command:
  There is no AT Command to poll uplink
--* (% style="color:#037691" %)**Downlink Payload (prefix 0x08):**
++* (% style="color:#037691" %)Downlink Payload (prefix 0x08):
--**0x08 FF     **~/~/ Poll an uplink
++(% class="box infomessage" %)
++(((
++**0x08 FF     ~/~/ Poll an uplink,**
++)))
  **Example**: 0x08FF, ask device to send an Uplink
@@ -771,9 +771,12 @@
  Use of trigger mode, please check [[ADDMOD6>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
--* (% style="color:#037691" %)**AT Command:**
++* (% style="color:#037691" %)AT Command:
++(% class="box infomessage" %)
++(((
  **AT+ADDMOD6=1 or 0**
++)))
 : Enable Trigger Mode
@@ -780,13 +780,11 @@
 : Disable Trigger Mode
--* (% style="color:#037691" %)**Downlink Payload (prefix 0x0A 06):**
++* (% style="color:#037691" %)Downlink Payload (prefix 0x0A 06):
--**0x0A 06 aa    ** ~/~/ Same as AT+ADDMOD6=aa
--
  (% class="box infomessage" %)
  (((
--
++**0x0A 06 aa     ~/~/ Same as AT+ADDMOD6=aa,**
  )))
@@ -815,7 +815,10 @@
  * (% style="color:#037691" %)AT Command:
++(% class="box infomessage" %)
++(((
  **Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >**
++)))
  **Example:**
@@ -824,11 +824,13 @@
  * (% style="color:#037691" %)Downlink Payload (prefix 0xAA 02):
--**0xAA 02 aa bb        **~/~/ Same as AT+DTRI=aa,bb
++(% class="box infomessage" %)
++(((
++**0xAA 02 aa bb  ~/~/ Same as AT+DTRI=aa,bb**
++)))
--
  ==== 3.4.2.7 Trigger1 – Set DI1 or DI3 as trigger ====
  Set DI1 or DI3(for LT-33222-L) trigger.
@@ -835,7 +835,10 @@
  * (% style="color:#037691" %)AT Command:
++(% class="box infomessage" %)
++(((
  **AT+TRIG1=a,b**
++)))
  a : Interrupt mode. 0: falling edge; 1: rising edge, 2: falling and raising edge(for MOD=1).
@@ -847,19 +847,26 @@
  AT+TRIG1=1,100(set DI1 port to trigger on high level, valid signal is 100ms )
--* (% style="color:#037691" %)**Downlink Payload (prefix 0x09 01 ):**
--* **0x09 01 aa bb cc    **     ~/~/ same as AT+TRIG1=aa,0x(bb cc)
++* (% style="color:#037691" %)Downlink Payload (prefix 0x09 01 ):
++(% class="box infomessage" %)
++(((
++**0x09 01 aa bb cc ~/~/ same as AT+TRIG1=aa,0x(bb cc)**
++)))
++
++
  ==== 3.4.2.8 Trigger2 – Set DI2 as trigger ====
  Set DI2 trigger.
--* (% style="color:#037691" %)**AT Command:**
++* (% style="color:#037691" %)AT Command:
++(% class="box infomessage" %)
++(((
  **AT+TRIG2=a,b**
++)))
--
  a : Interrupt mode. 0: falling edge; 1: rising edge, 2: falling and raising edge(for MOD=1).
  b : delay timing.
@@ -870,72 +870,93 @@
  AT+TRIG2=0,100(set DI1 port to trigger on low level, valid signal is 100ms )
--* (% style="color:#037691" %)**Downlink Payload (prefix 0x09 02 ):**
++* (% style="color:#037691" %)Downlink Payload (prefix 0x09 02 ):
--**0x09 02 aa bb cc           **~/~/ same as AT+TRIG1=aa,0x(bb cc)
++(% class="box infomessage" %)
++(((
++**0x09 02 aa bb cc ~/~/ same as AT+TRIG1=aa,0x(bb cc)**
++)))
--
  ==== 3.4.2.9 Trigger – Set AC (current) as trigger ====
  Set current trigger , base on AC port. See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
--* (% style="color:#037691" %)**AT Command**
++* (% style="color:#037691" %)AT Command:
--**AT+ACLIM**
++(% class="box infomessage" %)
++(((
++**AT+ACLIM. **
++)))
--* (% style="color:#037691" %)**Downlink Payload (prefix 0xAA 01 )**
++* (% style="color:#037691" %)Downlink Payload (prefix 0xAA 01 ):
--**0x AA 01 aa bb cc dd ee ff gg hh        **   ~/~/ same as AT+ACLIM See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
++(% class="box infomessage" %)
++(((
++**0x AA 01 aa bb cc dd ee ff gg hh ~/~/ same as AT+ACLIM See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]**
++)))
--
  ==== 3.4.2.10 Trigger – Set AV (voltage) as trigger ====
  Set current trigger , base on AV port. See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
--* (% style="color:#037691" %)**AT Command**
++* (% style="color:#037691" %)AT Command:
--**AT+AVLIM            See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]**
++(% class="box infomessage" %)
++(((
++**AT+AVLIM. See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]**
++)))
--* (% style="color:#037691" %)**Downlink Payload (prefix 0xAA 00 )**
++* (% style="color:#037691" %)Downlink Payload (prefix 0xAA 00 ):
--**0x AA 00 aa bb cc dd ee ff gg hh    ** ~/~/ same as AT+AVLIM See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]]
++(% class="box infomessage" %)
++(((
++**0x AA 00 aa bb cc dd ee ff gg hh ~/~/ same as AT+AVLIM See [[trigger mode>>||anchor="H3.3.6AT2BADDMOD3D6.28TriggerMode2COptional29"]] **
++)))
--
  ==== 3.4.2.11 Trigger – Set minimum interval ====
  Set AV and AC trigger minimum interval, system won’t response to the second trigger within this set time after the first trigger.
--* (% style="color:#037691" %)**AT Command**
++* (% style="color:#037691" %)AT Command:
++(% class="box infomessage" %)
++(((
  **AT+ATDC=5. Device won’t response the second trigger within 5 minute after the first trigger.**
++)))
--* (% style="color:#037691" %)**Downlink Payload (prefix 0xAC )**
++* (% style="color:#037691" %)Downlink Payload (prefix 0xAC ):
--**0x AC aa bb   ** ~/~/ same as AT+ATDC=0x(aa bb)   . Unit (min)
++(% class="box infomessage" %)
++(((
++**0x AC aa bb ~/~/ same as AT+ATDC=0x(aa bb)   . Unit (min)**
++)))
--
  ==== 3.4.2.12 DO ~-~- Control Digital Output DO1/DO2/DO3 ====
--* (% style="color:#037691" %)**AT Command**
++* (% style="color:#037691" %)AT Command:
  There is no AT Command to control Digital Output
--* (% style="color:#037691" %)**Downlink Payload (prefix 0x02)**
--* **0x02 aa bb cc     **~/~/ Set DO1/DO2/DO3 output
++* (% style="color:#037691" %)Downlink Payload (prefix 0x02):
++(% class="box infomessage" %)
  (((
++**0x02 aa bb cc     ~/~/ Set DO1/DO2/DO3 output**
++)))
++
++(((
  If payload = 0x02010001, while there is load between V+ and DOx, it means set DO1 to low, DO2 to high and DO3 to low.
  )))
@@ -955,19 +955,22 @@
--
  ==== 3.4.2.13 DO ~-~- Control Digital Output DO1/DO2/DO3 with time control ====
--* (% style="color:#037691" %)**AT Command**
++* (% style="color:#037691" %)AT Command:
  There is no AT Command to control Digital Output
--* (% style="color:#037691" %)**Downlink Payload (prefix 0xA9)**
++* (% style="color:#037691" %)Downlink Payload (prefix 0xA9):
--**0xA9 aa bb cc     **~/~/ Set DO1/DO2/DO3 output with time control
++(% class="box infomessage" %)
++(((
++(((
++**0xA9 aa bb cc     ~/~/ Set DO1/DO2/DO3 output with time control**
++)))
++)))
--
  This is to control the digital output time of DO pin. Include four bytes:
  (% style="color:#4f81bd" %)**First Byte**(%%)**:** Type code (0xA9)
@@ -1021,19 +1021,20 @@
--
  ==== 3.4.2.14 Relay ~-~- Control Relay Output RO1/RO2 ====
--* (% style="color:#037691" %)**AT Command:**
++* (% style="color:#037691" %)AT Command:
  There is no AT Command to control Relay Output
--* (% style="color:#037691" %)**Downlink Payload (prefix 0x03):**
++* (% style="color:#037691" %)Downlink Payload (prefix 0x03):
--**0x03 aa bb     **~/~/ Set RO1/RO2 output
++(% class="box infomessage" %)
++(((
++**0x03 aa bb     ~/~/ Set RO1/RO2 output**
++)))
--
  (((
  If payload = 0x030100, it means set RO1 to close and RO2 to open.
  )))
@@ -1050,19 +1050,20 @@
--
  ==== 3.4.2.15 Relay ~-~- Control Relay Output RO1/RO2 with time control ====
--* (% style="color:#037691" %)**AT Command:**
++* (% style="color:#037691" %)AT Command:
  There is no AT Command to control Relay Output
--* (% style="color:#037691" %)**Downlink Payload (prefix 0x05):**
++* (% style="color:#037691" %)Downlink Payload (prefix 0x05):
--**0x05 aa bb cc dd     **~/~/ Set RO1/RO2 relay with time control
++(% class="box infomessage" %)
++(((
++**0x05 aa bb cc dd     ~/~/ Set RO1/RO2 relay with time control:**
++)))
--
  This is to control the relay output time of relay. Include four bytes:
  (% style="color:#4f81bd" %)**First Byte **(%%)**:** Type code (0x05)
@@ -1104,28 +1104,35 @@
--
  ==== 3.4.2.16 Counting ~-~- Voltage threshold counting ====
  When voltage exceed the threshold, count. Feature see [[MOD4>>||anchor="H3.3.4AT2BMOD3D42CSingleDICounting2B1xVoltageCounting"]]
--* (% style="color:#037691" %)**AT Command:**
++* (% style="color:#037691" %)AT Command:
--**AT+VOLMAX   ** ~/~/ See [[MOD4>>||anchor="H3.3.4AT2BMOD3D42CSingleDICounting2B1xVoltageCounting"]]
++(% class="box infomessage" %)
++(((
++**AT+VOLMAX    ~/~/ See [[MOD4>>||anchor="H3.3.4AT2BMOD3D42CSingleDICounting2B1xVoltageCounting"]]**
++)))
--* (% style="color:#037691" %)**Downlink Payload (prefix 0xA5):**
++* (% style="color:#037691" %)Downlink Payload (prefix 0xA5):
--**0xA5 aa bb cc   **~/~/ Same as AT+VOLMAX=(aa bb),cc
++(% class="box infomessage" %)
++(((
++**0xA5 aa bb cc   ~/~/ Same as AT+VOLMAX=(aa bb),cc**
++)))
--
  ==== 3.4.2.17 Counting ~-~- Pre-configure the Count Number ====
--* (% style="color:#037691" %)**AT Command:**
++* (% style="color:#037691" %)AT Command:
--(% style="color:#037691" %)****(%%)**AT+SETCNT=aa,(bb cc dd ee) **
++(% class="box infomessage" %)
++(((
++**AT+SETCNT=aa,(bb cc dd ee) **
++)))
  aa: 1: Set count1,
@@ -1136,29 +1136,35 @@
  Bb cc dd ee: number to be set
--* (% style="color:#037691" %)**Downlink Payload (prefix 0xA8):**
++* (% style="color:#037691" %)Downlink Payload (prefix 0xA8):
--**0x A8 aa bb cc dd ee     **~/~/ same as AT+SETCNT=aa,(bb cc dd ee)
++(% class="box infomessage" %)
++(((
++**0x A8 aa bb cc dd ee     ~/~/ same as AT+SETCNT=aa,(bb cc dd ee)**
++)))
--
  ==== 3.4.2.18 Counting ~-~- Clear Counting ====
  Clear counting for counting mode
--* (% style="color:#037691" %)**AT Command:**
++* (% style="color:#037691" %)AT Command:
--(% style="color:#037691" %)(%%)**AT+CLRCOUNT ** ~/~/ clear all counting
++(% class="box infomessage" %)
++(((
++**AT+CLRCOUNT  ~/~/ clear all counting**
++)))
++* (% style="color:#037691" %)Downlink Payload (prefix 0xA6):
--* (% style="color:#037691" %)**Downlink Payload (prefix 0xA6):**
++(% class="box infomessage" %)
++(((
++**0x A6 01     ~/~/ clear all counting,**
++)))
--**0x A6 01    ** ~/~/ clear all counting
--
--
  ==== 3.4.2.19 Counting ~-~- Change counting mode save time ====
  * (% style="color:#037691" %)**AT Command:**
@@ -1177,7 +1177,6 @@
  )))
--
  == 3.5 Integrate with Mydevice ==
  Mydevices provides a human friendly interface to show the sensor data, once we have data in TTN, we can use Mydevices to connect to TTN and see the data in Mydevices. Below are the steps: