Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -76,8 +76,6 @@
76	76	)))
77	77
78	78	(((
79		-
80		-
81	81	**Interface for Model: LT22222-L:**
82	82	)))
83	83
...	...	@@ -101,8 +101,6 @@
101	101	)))
102	102
103	103	(((
104		-
105		-
106	106	**LoRa Spec:**
107	107	)))
108	108
...	...	@@ -162,6 +162,8 @@
162	162	)))
163	163	* (((
164	164	Packet engine up to 256 bytes with CRC.
	161	+
	162	+
165	165	)))
166	166
167	167	== 1.3 Features ==
...	...	@@ -196,6 +196,7 @@
196	196	* 1 x Counting Port
197	197	)))
198	198
	197	+
199	199	= 2. Power ON Device =
200	200
201	201	The LT controller can be powered by 7 ~~ 24V DC power source. Connect VIN to Power Input V+ and GND to power input V- to power the LT controller.
...	...	@@ -276,6 +276,8 @@
276	276	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
277	277	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
278	278
	278	+
	279	+
279	279	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
280	280
281	281	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -330,6 +330,8 @@
330	330	** DO1 is high in case there is load between DO1 and V+.
331	331	** DO1 LED is off in both case
332	332
	334	+
	335	+
333	333	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
334	334
335	335
...	...	@@ -470,10 +470,11 @@
470	470
471	471	(((
472	472	Other AT Commands for counting are similar to [[MOD2 Counting Command>>||anchor="H3.3.2AT2BMOD3D22C28DoubleDICounting29"]].
	476	+
	477	+
473	473	)))
474	474
475	475
476		-
477	477	=== 3.3.4 AT+MOD~=4, Single DI Counting + 1 x Voltage Counting ===
478	478
479	479
...	...	@@ -626,6 +626,7 @@
626	626	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
627	627	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
628	628
	633	+
629	629	**AT Command to set Trigger Condition**:
630	630
631	631	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -705,6 +705,7 @@
705	705
706	706	* Each bits shows if the corresponding trigger has been configured.
707	707
	713	+
708	708	**Example:**
709	709
710	710	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -716,6 +716,7 @@
716	716
717	717	* Each bits shows which status has been trigger on this uplink.
718	718
	725	+
719	719	**Example:**
720	720
721	721	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -727,6 +727,7 @@
727	727
728	728	* Each bits shows which status has been trigger on this uplink.
729	729
	737	+
730	730	**Example:**
731	731
732	732	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -755,6 +755,7 @@
755	755	)))
756	756
757	757
	766	+
758	758	== 3.4 ​Configure LT via AT or Downlink ==
759	759
760	760	User can configure LT I/O Controller via AT Commands or LoRaWAN Downlink Commands
...	...	@@ -768,7 +768,6 @@
768	768	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
769	769
770	770
771		-
772	772	=== 3.4.1 Common Commands ===
773	773
774	774	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]