Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -76,8 +76,6 @@
76	76	)))
77	77
78	78	(((
79		-
80		-
81	81	**Interface for Model: LT22222-L:**
82	82	)))
83	83
...	...	@@ -101,8 +101,6 @@
101	101	)))
102	102
103	103	(((
104		-
105		-
106	106	**LoRa Spec:**
107	107	)))
108	108
...	...	@@ -162,8 +162,13 @@
162	162	)))
163	163	* (((
164	164	Packet engine up to 256 bytes with CRC.
	161	+
	162	+
165	165	)))
166	166
	165	+
	166	+
	167	+
167	167	== 1.3 Features ==
168	168
169	169	* LoRaWAN Class A & Class C protocol
...	...	@@ -174,6 +174,9 @@
174	174	* Firmware upgradable via program port
175	175	* Counting
176	176
	178	+
	179	+
	180	+
177	177	== 1.4  Applications ==
178	178
179	179	* Smart Buildings & Home Automation
...	...	@@ -183,6 +183,9 @@
183	183	* Smart Cities
184	184	* Smart Factory
185	185
	190	+
	191	+
	192	+
186	186	== 1.5 Hardware Variants ==
187	187
188	188	(% border="1" style="background-color:#f7faff; width:500px" %)
...	...	@@ -196,6 +196,8 @@
196	196	* 1 x Counting Port
197	197	)))
198	198
	206	+
	207	+
199	199	= 2. Power ON Device =
200	200
201	201	The LT controller can be powered by 7 ~~ 24V DC power source. Connect VIN to Power Input V+ and GND to power input V- to power the LT controller.
...	...	@@ -316,6 +316,7 @@
316	316	* [1] RO1 relay channel is close and the RO1 LED is ON.
317	317	* [0] RO2 relay channel is open and RO2 LED is OFF;
318	318
	328	+
319	319	**LT22222-L:**
320	320
321	321	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -478,7 +478,6 @@
478	478	)))
479	479
480	480
481		-
482	482	=== 3.3.4 AT+MOD~=4, Single DI Counting + 1 x Voltage Counting ===
483	483
484	484
...	...	@@ -631,6 +631,7 @@
631	631	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
632	632	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
633	633
	643	+
634	634	**AT Command to set Trigger Condition**:
635	635
636	636	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -710,6 +710,7 @@
710	710
711	711	* Each bits shows if the corresponding trigger has been configured.
712	712
	723	+
713	713	**Example:**
714	714
715	715	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -721,6 +721,7 @@
721	721
722	722	* Each bits shows which status has been trigger on this uplink.
723	723
	735	+
724	724	**Example:**
725	725
726	726	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -732,6 +732,7 @@
732	732
733	733	* Each bits shows which status has been trigger on this uplink.
734	734
	747	+
735	735	**Example:**
736	736
737	737	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -773,6 +773,7 @@
773	773
774	774	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
775	775
	789	+
776	776	=== 3.4.1 Common Commands ===
777	777
778	778	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]