Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -76,8 +76,6 @@
76	76	)))
77	77
78	78	(((
79		-
80		-
81	81	**Interface for Model: LT22222-L:**
82	82	)))
83	83
...	...	@@ -101,8 +101,6 @@
101	101	)))
102	102
103	103	(((
104		-
105		-
106	106	**LoRa Spec:**
107	107	)))
108	108
...	...	@@ -162,9 +162,13 @@
162	162	)))
163	163	* (((
164	164	Packet engine up to 256 bytes with CRC.
	161	+
	162	+
165	165	)))
166	166
167	167
	166	+
	167	+
168	168	== 1.3 Features ==
169	169
170	170	* LoRaWAN Class A & Class C protocol
...	...	@@ -176,6 +176,8 @@
176	176	* Counting
177	177
178	178
	179	+
	180	+
179	179	== 1.4  Applications ==
180	180
181	181	* Smart Buildings & Home Automation
...	...	@@ -186,6 +186,8 @@
186	186	* Smart Factory
187	187
188	188
	191	+
	192	+
189	189	== 1.5 Hardware Variants ==
190	190
191	191	(% border="1" style="background-color:#f7faff; width:500px" %)
...	...	@@ -200,6 +200,7 @@
200	200	)))
201	201
202	202
	207	+
203	203	= 2. Power ON Device =
204	204
205	205	The LT controller can be powered by 7 ~~ 24V DC power source. Connect VIN to Power Input V+ and GND to power input V- to power the LT controller.
...	...	@@ -282,7 +282,6 @@
282	282
283	283
284	284
285		-
286	286	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
287	287
288	288	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -321,6 +321,7 @@
321	321	* [1] RO1 relay channel is close and the RO1 LED is ON.
322	322	* [0] RO2 relay channel is open and RO2 LED is OFF;
323	323
	328	+
324	324	**LT22222-L:**
325	325
326	326	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -338,7 +338,6 @@
338	338
339	339
340	340
341		-
342	342	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
343	343
344	344
...	...	@@ -484,7 +484,6 @@
484	484	)))
485	485
486	486
487		-
488	488	=== 3.3.4 AT+MOD~=4, Single DI Counting + 1 x Voltage Counting ===
489	489
490	490
...	...	@@ -637,6 +637,7 @@
637	637	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
638	638	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
639	639
	643	+
640	640	**AT Command to set Trigger Condition**:
641	641
642	642	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -716,6 +716,7 @@
716	716
717	717	* Each bits shows if the corresponding trigger has been configured.
718	718
	723	+
719	719	**Example:**
720	720
721	721	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -727,6 +727,7 @@
727	727
728	728	* Each bits shows which status has been trigger on this uplink.
729	729
	735	+
730	730	**Example:**
731	731
732	732	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -738,6 +738,7 @@
738	738
739	739	* Each bits shows which status has been trigger on this uplink.
740	740
	747	+
741	741	**Example:**
742	742
743	743	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -779,6 +779,7 @@
779	779
780	780	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
781	781
	789	+
782	782	=== 3.4.1 Common Commands ===
783	783
784	784	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]