Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -76,8 +76,6 @@
76	76	)))
77	77
78	78	(((
79		-
80		-
81	81	**Interface for Model: LT22222-L:**
82	82	)))
83	83
...	...	@@ -101,8 +101,6 @@
101	101	)))
102	102
103	103	(((
104		-
105		-
106	106	**LoRa Spec:**
107	107	)))
108	108
...	...	@@ -162,10 +162,10 @@
162	162	)))
163	163	* (((
164	164	Packet engine up to 256 bytes with CRC.
	161	+
	162	+
165	165	)))
166	166
167		-
168		-
169	169	== 1.3 Features ==
170	170
171	171	* LoRaWAN Class A & Class C protocol
...	...	@@ -176,8 +176,6 @@
176	176	* Firmware upgradable via program port
177	177	* Counting
178	178
179		-
180		-
181	181	== 1.4  Applications ==
182	182
183	183	* Smart Buildings & Home Automation
...	...	@@ -187,8 +187,6 @@
187	187	* Smart Cities
188	188	* Smart Factory
189	189
190		-
191		-
192	192	== 1.5 Hardware Variants ==
193	193
194	194	(% border="1" style="background-color:#f7faff; width:500px" %)
...	...	@@ -285,6 +285,7 @@
285	285	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
286	286
287	287
	280	+
288	288	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
289	289
290	290	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -323,6 +323,7 @@
323	323	* [1] RO1 relay channel is close and the RO1 LED is ON.
324	324	* [0] RO2 relay channel is open and RO2 LED is OFF;
325	325
	319	+
326	326	**LT22222-L:**
327	327
328	328	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -339,6 +339,7 @@
339	339	** DO1 LED is off in both case
340	340
341	341
	336	+
342	342	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
343	343
344	344
...	...	@@ -636,6 +636,7 @@
636	636	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
637	637	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
638	638
	634	+
639	639	**AT Command to set Trigger Condition**:
640	640
641	641	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -715,6 +715,7 @@
715	715
716	716	* Each bits shows if the corresponding trigger has been configured.
717	717
	714	+
718	718	**Example:**
719	719
720	720	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -726,6 +726,7 @@
726	726
727	727	* Each bits shows which status has been trigger on this uplink.
728	728
	726	+
729	729	**Example:**
730	730
731	731	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -737,6 +737,7 @@
737	737
738	738	* Each bits shows which status has been trigger on this uplink.
739	739
	738	+
740	740	**Example:**
741	741
742	742	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -778,6 +778,7 @@
778	778
779	779	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
780	780
	780	+
781	781	=== 3.4.1 Common Commands ===
782	782
783	783	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]