Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -275,8 +275,6 @@
275	275	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
278		-
279		-
280	280	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
281	281
282	282	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -284,8 +284,6 @@
284	284	[[image:image-20220523174024-3.png]]
285	285
286	286	(((
287		-
288		-
289	289	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
290	290	)))
291	291
...	...	@@ -299,7 +299,6 @@
299	299
300	300	For example if payload is: [[image:image-20220523175847-2.png]]
301	301
302		-
303	303	**The value for the interface is:  **
304	304
305	305	AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V
...	...	@@ -315,8 +315,6 @@
315	315	* [1] RO1 relay channel is close and the RO1 LED is ON.
316	316	* [0] RO2 relay channel is open and RO2 LED is OFF;
317	317
318		-
319		-
320	320	**LT22222-L:**
321	321
322	322	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -633,7 +633,6 @@
633	633	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
634	634
635	635
636		-
637	637	**AT Command to set Trigger Condition**:
638	638
639	639	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -647,7 +647,6 @@
647	647	AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
648	648
649	649
650		-
651	651	(% style="color:#4f81bd" %)**Trigger base on current**:
652	652
653	653	Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
...	...	@@ -657,7 +657,6 @@
657	657	AT+ACLIM=10000,15000,0,0   (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
658	658
659	659
660		-
661	661	(% style="color:#4f81bd" %)**Trigger base on DI status**:
662	662
663	663	DI status trigger Flag.
...	...	@@ -664,13 +664,12 @@
664	664
665	665	Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
666	666
667		-
668	668	**Example:**
669	669
670	670	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
671	671
672	672
673		-**Downlink Command to set Trigger Condition:**
	662	+**Downlink Command to set Trigger Condition**
674	674
675	675	Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
676	676
...	...	@@ -699,7 +699,6 @@
699	699	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
700	700
701	701
702		-
703	703	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
704	704
705	705	MOD6 Payload : total 11 bytes payload
...	...	@@ -714,7 +714,6 @@
714	714	* Each bits shows if the corresponding trigger has been configured.
715	715
716	716
717		-
718	718	**Example:**
719	719
720	720	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -727,7 +727,6 @@
727	727	* Each bits shows which status has been trigger on this uplink.
728	728
729	729
730		-
731	731	**Example:**
732	732
733	733	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -740,7 +740,6 @@
740	740	* Each bits shows which status has been trigger on this uplink.
741	741
742	742
743		-
744	744	**Example:**
745	745
746	746	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.