Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -314,8 +314,6 @@
314	314	* [1] RO1 relay channel is close and the RO1 LED is ON.
315	315	* [0] RO2 relay channel is open and RO2 LED is OFF;
316	316
317		-
318		-
319	319	**LT22222-L:**
320	320
321	321	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -332,7 +332,6 @@
332	332	** DO1 LED is off in both case
333	333
334	334
335		-
336	336	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
337	337
338	338
...	...	@@ -625,14 +625,11 @@
625	625	* **AT+MOD=1 ** **~-~->** The normal working mode
626	626	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
627	627
628		-
629	629	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
630	630
631	631	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
632	632	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
633	633
634		-
635		-
636	636	**AT Command to set Trigger Condition**:
637	637
638	638	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -646,7 +646,6 @@
646	646	AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
647	647
648	648
649		-
650	650	(% style="color:#4f81bd" %)**Trigger base on current**:
651	651
652	652	Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
...	...	@@ -656,7 +656,6 @@
656	656	AT+ACLIM=10000,15000,0,0   (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
657	657
658	658
659		-
660	660	(% style="color:#4f81bd" %)**Trigger base on DI status**:
661	661
662	662	DI status trigger Flag.
...	...	@@ -663,13 +663,12 @@
663	663
664	664	Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
665	665
666		-
667	667	**Example:**
668	668
669	669	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
670	670
671	671
672		-**Downlink Command to set Trigger Condition:**
	663	+**Downlink Command to set Trigger Condition**
673	673
674	674	Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
675	675
...	...	@@ -698,7 +698,6 @@
698	698	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
699	699
700	700
701		-
702	702	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
703	703
704	704	MOD6 Payload : total 11 bytes payload
...	...	@@ -712,8 +712,6 @@
712	712
713	713	* Each bits shows if the corresponding trigger has been configured.
714	714
715		-
716		-
717	717	**Example:**
718	718
719	719	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW