Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -275,7 +275,6 @@
275	275	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
278		-
279	279	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
280	280
281	281	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -283,8 +283,6 @@
283	283	[[image:image-20220523174024-3.png]]
284	284
285	285	(((
286		-
287		-
288	288	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
289	289	)))
290	290
...	...	@@ -298,7 +298,6 @@
298	298
299	299	For example if payload is: [[image:image-20220523175847-2.png]]
300	300
301		-
302	302	**The value for the interface is:  **
303	303
304	304	AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V
...	...	@@ -314,8 +314,6 @@
314	314	* [1] RO1 relay channel is close and the RO1 LED is ON.
315	315	* [0] RO2 relay channel is open and RO2 LED is OFF;
316	316
317		-
318		-
319	319	**LT22222-L:**
320	320
321	321	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -331,8 +331,6 @@
331	331	** DO1 is high in case there is load between DO1 and V+.
332	332	** DO1 LED is off in both case
333	333
334		-
335		-
336	336	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
337	337
338	338
...	...	@@ -632,7 +632,6 @@
632	632	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
633	633
634	634
635		-
636	636	**AT Command to set Trigger Condition**:
637	637
638	638	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -646,7 +646,6 @@
646	646	AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
647	647
648	648
649		-
650	650	(% style="color:#4f81bd" %)**Trigger base on current**:
651	651
652	652	Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
...	...	@@ -656,7 +656,6 @@
656	656	AT+ACLIM=10000,15000,0,0   (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
657	657
658	658
659		-
660	660	(% style="color:#4f81bd" %)**Trigger base on DI status**:
661	661
662	662	DI status trigger Flag.
...	...	@@ -663,13 +663,12 @@
663	663
664	664	Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
665	665
666		-
667	667	**Example:**
668	668
669	669	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
670	670
671	671
672		-**Downlink Command to set Trigger Condition:**
	660	+**Downlink Command to set Trigger Condition**
673	673
674	674	Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
675	675
...	...	@@ -698,7 +698,6 @@
698	698	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
699	699
700	700
701		-
702	702	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
703	703
704	704	MOD6 Payload : total 11 bytes payload
...	...	@@ -713,7 +713,6 @@
713	713	* Each bits shows if the corresponding trigger has been configured.
714	714
715	715
716		-
717	717	**Example:**
718	718
719	719	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -726,7 +726,6 @@
726	726	* Each bits shows which status has been trigger on this uplink.
727	727
728	728
729		-
730	730	**Example:**
731	731
732	732	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -739,7 +739,6 @@
739	739	* Each bits shows which status has been trigger on this uplink.
740	740
741	741
742		-
743	743	**Example:**
744	744
745	745	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.