Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -275,7 +275,6 @@
275	275	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
278		-
279	279	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
280	280
281	281	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -283,8 +283,6 @@
283	283	[[image:image-20220523174024-3.png]]
284	284
285	285	(((
286		-
287		-
288	288	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
289	289	)))
290	290
...	...	@@ -315,7 +315,6 @@
315	315	* [0] RO2 relay channel is open and RO2 LED is OFF;
316	316
317	317
318		-
319	319	**LT22222-L:**
320	320
321	321	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -332,6 +332,7 @@
332	332	** DO1 LED is off in both case
333	333
334	334
	331	+
335	335	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
336	336
337	337
...	...	@@ -624,14 +624,11 @@
624	624	* **AT+MOD=1 ** **~-~->** The normal working mode
625	625	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
626	626
627		-
628	628	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
629	629
630	630	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
631	631	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
632	632
633		-
634		-
635	635	**AT Command to set Trigger Condition**:
636	636
637	637	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -645,7 +645,6 @@
645	645	AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
646	646
647	647
648		-
649	649	(% style="color:#4f81bd" %)**Trigger base on current**:
650	650
651	651	Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
...	...	@@ -655,7 +655,6 @@
655	655	AT+ACLIM=10000,15000,0,0   (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
656	656
657	657
658		-
659	659	(% style="color:#4f81bd" %)**Trigger base on DI status**:
660	660
661	661	DI status trigger Flag.
...	...	@@ -662,13 +662,12 @@
662	662
663	663	Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
664	664
665		-
666	666	**Example:**
667	667
668	668	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
669	669
670	670
671		-**Downlink Command to set Trigger Condition:**
	662	+**Downlink Command to set Trigger Condition**
672	672
673	673	Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
674	674
...	...	@@ -697,7 +697,6 @@
697	697	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
698	698
699	699
700		-
701	701	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
702	702
703	703	MOD6 Payload : total 11 bytes payload
...	...	@@ -711,8 +711,6 @@
711	711
712	712	* Each bits shows if the corresponding trigger has been configured.
713	713
714		-
715		-
716	716	**Example:**
717	717
718	718	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -724,8 +724,6 @@
724	724
725	725	* Each bits shows which status has been trigger on this uplink.
726	726
727		-
728		-
729	729	**Example:**
730	730
731	731	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -737,8 +737,6 @@
737	737
738	738	* Each bits shows which status has been trigger on this uplink.
739	739
740		-
741		-
742	742	**Example:**
743	743
744	744	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -781,7 +781,6 @@
781	781	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
782	782
783	783
784		-
785	785	=== 3.4.1 Common Commands ===
786	786
787	787	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]