Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -276,6 +276,7 @@
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
278	278
	279	+
279	279	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
280	280
281	281	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -314,6 +314,7 @@
314	314	* [1] RO1 relay channel is close and the RO1 LED is ON.
315	315	* [0] RO2 relay channel is open and RO2 LED is OFF;
316	316
	318	+
317	317	**LT22222-L:**
318	318
319	319	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -330,6 +330,7 @@
330	330	** DO1 LED is off in both case
331	331
332	332
	335	+
333	333	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
334	334
335	335
...	...	@@ -627,8 +627,6 @@
627	627	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
628	628	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
629	629
630		-
631		-
632	632	**AT Command to set Trigger Condition**:
633	633
634	634	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -642,7 +642,6 @@
642	642	AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
643	643
644	644
645		-
646	646	(% style="color:#4f81bd" %)**Trigger base on current**:
647	647
648	648	Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
...	...	@@ -652,7 +652,6 @@
652	652	AT+ACLIM=10000,15000,0,0   (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
653	653
654	654
655		-
656	656	(% style="color:#4f81bd" %)**Trigger base on DI status**:
657	657
658	658	DI status trigger Flag.
...	...	@@ -659,13 +659,12 @@
659	659
660	660	Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
661	661
662		-
663	663	**Example:**
664	664
665	665	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
666	666
667	667
668		-**Downlink Command to set Trigger Condition:**
	666	+**Downlink Command to set Trigger Condition**
669	669
670	670	Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
671	671
...	...	@@ -694,7 +694,6 @@
694	694	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
695	695
696	696
697		-
698	698	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
699	699
700	700	MOD6 Payload : total 11 bytes payload
...	...	@@ -708,8 +708,6 @@
708	708
709	709	* Each bits shows if the corresponding trigger has been configured.
710	710
711		-
712		-
713	713	**Example:**
714	714
715	715	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -721,8 +721,6 @@
721	721
722	722	* Each bits shows which status has been trigger on this uplink.
723	723
724		-
725		-
726	726	**Example:**
727	727
728	728	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -734,8 +734,6 @@
734	734
735	735	* Each bits shows which status has been trigger on this uplink.
736	736
737		-
738		-
739	739	**Example:**
740	740
741	741	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -778,7 +778,6 @@
778	778	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
779	779
780	780
781		-
782	782	=== 3.4.1 Common Commands ===
783	783
784	784	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]