Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -275,7 +275,6 @@
275	275	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
278		-
279	279	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
280	280
281	281	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -283,8 +283,6 @@
283	283	[[image:image-20220523174024-3.png]]
284	284
285	285	(((
286		-
287		-
288	288	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
289	289	)))
290	290
...	...	@@ -298,7 +298,6 @@
298	298
299	299	For example if payload is: [[image:image-20220523175847-2.png]]
300	300
301		-
302	302	**The value for the interface is:  **
303	303
304	304	AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V
...	...	@@ -314,6 +314,7 @@
314	314	* [1] RO1 relay channel is close and the RO1 LED is ON.
315	315	* [0] RO2 relay channel is open and RO2 LED is OFF;
316	316
	313	+
317	317	**LT22222-L:**
318	318
319	319	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -330,6 +330,7 @@
330	330	** DO1 LED is off in both case
331	331
332	332
	330	+
333	333	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
334	334
335	335
...	...	@@ -655,7 +655,6 @@
655	655
656	656	Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
657	657
658		-
659	659	**Example:**
660	660
661	661	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
...	...	@@ -685,7 +685,6 @@
685	685	Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
686	686
687	687
688		-
689	689	**Example2**: AA 02 01 00
690	690
691	691	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
...	...	@@ -704,8 +704,6 @@
704	704
705	705	* Each bits shows if the corresponding trigger has been configured.
706	706
707		-
708		-
709	709	**Example:**
710	710
711	711	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -717,8 +717,6 @@
717	717
718	718	* Each bits shows which status has been trigger on this uplink.
719	719
720		-
721		-
722	722	**Example:**
723	723
724	724	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -730,8 +730,6 @@
730	730
731	731	* Each bits shows which status has been trigger on this uplink.
732	732
733		-
734		-
735	735	**Example:**
736	736
737	737	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -774,7 +774,6 @@
774	774	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
775	775
776	776
777		-
778	778	=== 3.4.1 Common Commands ===
779	779
780	780	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]