Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -275,7 +275,6 @@
275	275	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
278		-
279	279	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
280	280
281	281	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -283,8 +283,6 @@
283	283	[[image:image-20220523174024-3.png]]
284	284
285	285	(((
286		-
287		-
288	288	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
289	289	)))
290	290
...	...	@@ -298,7 +298,6 @@
298	298
299	299	For example if payload is: [[image:image-20220523175847-2.png]]
300	300
301		-
302	302	**The value for the interface is:  **
303	303
304	304	AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V
...	...	@@ -329,10 +329,8 @@
329	329	** DO1 is high in case there is load between DO1 and V+.
330	330	** DO1 LED is off in both case
331	331
332		-
333	333	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
334	334
335		-
336	336	**For LT-22222-L**: this mode the **DI1 and DI2** are used as counting pins.
337	337
338	338	(((
...	...	@@ -341,7 +341,6 @@
341	341
342	342	[[image:image-20220523180452-3.png]]
343	343
344		-
345	345	(((
346	346	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DO3, DO2 and DO1. Totally 1bytes as below
347	347	)))
...	...	@@ -622,11 +622,13 @@
622	622	* **AT+MOD=1 ** **~-~->** The normal working mode
623	623	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
624	624
	618	+
625	625	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
626	626
627	627	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
628	628	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
629	629
	624	+
630	630	**AT Command to set Trigger Condition**:
631	631
632	632	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -702,6 +702,7 @@
702	702
703	703	* Each bits shows if the corresponding trigger has been configured.
704	704
	700	+
705	705	**Example:**
706	706
707	707	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -714,7 +714,6 @@
714	714	* Each bits shows which status has been trigger on this uplink.
715	715
716	716
717		-
718	718	**Example:**
719	719
720	720	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -727,7 +727,6 @@
727	727	* Each bits shows which status has been trigger on this uplink.
728	728
729	729
730		-
731	731	**Example:**
732	732
733	733	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.