Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -276,7 +276,6 @@
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
278	278
279		-
280	280	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
281	281
282	282	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -316,6 +316,7 @@
316	316	* [0] RO2 relay channel is open and RO2 LED is OFF;
317	317
318	318
	318	+
319	319	**LT22222-L:**
320	320
321	321	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -625,11 +625,14 @@
625	625	* **AT+MOD=1 ** **~-~->** The normal working mode
626	626	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
627	627
	628	+
628	628	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
629	629
630	630	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
631	631	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
632	632
	634	+
	635	+
633	633	**AT Command to set Trigger Condition**:
634	634
635	635	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -643,6 +643,7 @@
643	643	AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
644	644
645	645
	649	+
646	646	(% style="color:#4f81bd" %)**Trigger base on current**:
647	647
648	648	Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
...	...	@@ -652,6 +652,7 @@
652	652	AT+ACLIM=10000,15000,0,0   (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
653	653
654	654
	659	+
655	655	(% style="color:#4f81bd" %)**Trigger base on DI status**:
656	656
657	657	DI status trigger Flag.
...	...	@@ -658,12 +658,13 @@
658	658
659	659	Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
660	660
	666	+
661	661	**Example:**
662	662
663	663	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
664	664
665	665
666		-**Downlink Command to set Trigger Condition**
	672	+**Downlink Command to set Trigger Condition:**
667	667
668	668	Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
669	669
...	...	@@ -692,6 +692,7 @@
692	692	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
693	693
694	694
	701	+
695	695	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
696	696
697	697	MOD6 Payload : total 11 bytes payload
...	...	@@ -705,6 +705,8 @@
705	705
706	706	* Each bits shows if the corresponding trigger has been configured.
707	707
	715	+
	716	+
708	708	**Example:**
709	709
710	710	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -716,6 +716,8 @@
716	716
717	717	* Each bits shows which status has been trigger on this uplink.
718	718
	728	+
	729	+
719	719	**Example:**
720	720
721	721	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -727,6 +727,8 @@
727	727
728	728	* Each bits shows which status has been trigger on this uplink.
729	729
	741	+
	742	+
730	730	**Example:**
731	731
732	732	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -770,7 +770,6 @@
770	770
771	771
772	772
773		-
774	774	=== 3.4.1 Common Commands ===
775	775
776	776	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]