Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -276,7 +276,6 @@
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
278	278
279		-
280	280	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
281	281
282	282	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -315,7 +315,6 @@
315	315	* [1] RO1 relay channel is close and the RO1 LED is ON.
316	316	* [0] RO2 relay channel is open and RO2 LED is OFF;
317	317
318		-
319	319	**LT22222-L:**
320	320
321	321	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -332,7 +332,6 @@
332	332	** DO1 LED is off in both case
333	333
334	334
335		-
336	336	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
337	337
338	338
...	...	@@ -658,6 +658,7 @@
658	658
659	659	Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
660	660
	658	+
661	661	**Example:**
662	662
663	663	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
...	...	@@ -687,6 +687,7 @@
687	687	Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
688	688
689	689
	688	+
690	690	**Example2**: AA 02 01 00
691	691
692	692	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
...	...	@@ -705,6 +705,8 @@
705	705
706	706	* Each bits shows if the corresponding trigger has been configured.
707	707
	707	+
	708	+
708	708	**Example:**
709	709
710	710	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -716,6 +716,8 @@
716	716
717	717	* Each bits shows which status has been trigger on this uplink.
718	718
	720	+
	721	+
719	719	**Example:**
720	720
721	721	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -727,6 +727,8 @@
727	727
728	728	* Each bits shows which status has been trigger on this uplink.
729	729
	733	+
	734	+
730	730	**Example:**
731	731
732	732	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -770,7 +770,6 @@
770	770
771	771
772	772
773		-
774	774	=== 3.4.1 Common Commands ===
775	775
776	776	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]