Skip to Content
Last modified by Mengting Qiu on 2025/06/04 18:42
From version 77.90
edited by Xiaoling
on 2022/06/10 09:28
Change comment: There is no comment for this version
To version 77.94
edited by Xiaoling
on 2022/06/10 09:31
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -276,7 +276,6 @@
276 276  * **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277 277  
278 278  
279 -
280 280  === 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
281 281  
282 282  The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
... ... @@ -315,7 +315,6 @@
315 315  * [1] RO1 relay channel is close and the RO1 LED is ON.
316 316  * [0] RO2 relay channel is open and RO2 LED is OFF;
317 317  
318 -
319 319  **LT22222-L:**
320 320  
321 321  * [1] DI2 channel is high input and DI2 LED is ON;
... ... @@ -332,7 +332,6 @@
332 332  ** DO1 LED is off in both case
333 333  
334 334  
335 -
336 336  === 3.3.2 AT+MOD~=2, (Double DI Counting) ===
337 337  
338 338  
... ... @@ -658,12 +658,13 @@
658 658  
659 659  Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
660 660  
658 +
661 661  **Example:**
662 662  
663 663  AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
664 664  
665 665  
666 -**Downlink Command to set Trigger Condition**
664 +**Downlink Command to set Trigger Condition:**
667 667  
668 668  Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
669 669  
... ... @@ -692,6 +692,7 @@
692 692  Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
693 693  
694 694  
693 +
695 695  (% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
696 696  
697 697  MOD6 Payload : total 11 bytes payload
... ... @@ -705,6 +705,8 @@
705 705  
706 706  * Each bits shows if the corresponding trigger has been configured.
707 707  
707 +
708 +
708 708  **Example:**
709 709  
710 710  10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
... ... @@ -716,6 +716,8 @@
716 716  
717 717  * Each bits shows which status has been trigger on this uplink.
718 718  
720 +
721 +
719 719  **Example:**
720 720  
721 721  10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
... ... @@ -727,6 +727,8 @@
727 727  
728 728  * Each bits shows which status has been trigger on this uplink.
729 729  
733 +
734 +
730 730  **Example:**
731 731  
732 732  00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
... ... @@ -769,6 +769,7 @@
769 769  * (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
770 770  
771 771  
777 +
772 772  === 3.4.1 Common Commands ===
773 773  
774 774  They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]