Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -285,6 +285,8 @@
285	285	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
286	286	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
287	287
	288	+
	289	+
288	288	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
289	289
290	290	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -320,6 +320,7 @@
320	320	* [1] RO1 relay channel is close and the RO1 LED is ON.
321	321	* [0] RO2 relay channel is open and RO2 LED is OFF;
322	322
	325	+
323	323	**LT22222-L:**
324	324
325	325	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -335,6 +335,8 @@
335	335	** DO1 is high in case there is load between DO1 and V+.
336	336	** DO1 LED is off in both case
337	337
	341	+
	342	+
338	338	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
339	339
340	340	**For LT-22222-L**: this mode the **DI1 and DI2** are used as counting pins.
...	...	@@ -428,6 +428,7 @@
428	428	)))
429	429
430	430
	436	+
431	431	=== 3.3.3 AT+MOD~=3, Single DI Counting + 2 x ACI ===
432	432
433	433	**LT22222-L**: This mode the DI1 is used as a counting pin.
...	...	@@ -472,6 +472,8 @@
472	472
473	473	)))
474	474
	481	+
	482	+
475	475	=== 3.3.4 AT+MOD~=4, Single DI Counting + 1 x Voltage Counting ===
476	476
477	477	**LT22222-L**: This mode the DI1 is used as a counting pin.
...	...	@@ -553,6 +553,7 @@
553	553	)))
554	554
555	555
	564	+
556	556	=== 3.3.5 AT+MOD~=5, Single DI Counting + 2 x AVI + 1 x ACI ===
557	557
558	558	**LT22222-L**: This mode the DI1 is used as a counting pin.
...	...	@@ -597,6 +597,8 @@
597	597
598	598	)))
599	599
	609	+
	610	+
600	600	=== 3.3.6 AT+ADDMOD~=6. (Trigger Mode, Optional) ===
601	601
602	602	(% style="color:#4f81bd" %)**This mode is an optional mode for trigger purpose. It can run together with other mode.**
...	...	@@ -720,6 +720,7 @@
720	720	When device got this command, it will send the MOD6 payload.
721	721
722	722
	734	+
723	723	=== 3.3.7 Payload Decoder ===
724	724
725	725	(((
...	...	@@ -728,6 +728,8 @@
728	728
729	729	)))
730	730
	743	+
	744	+
731	731	== 3.4 ​Configure LT via AT or Downlink ==
732	732
733	733	User can configure LT I/O Controller via AT Commands or LoRaWAN Downlink Commands
...	...	@@ -740,11 +740,14 @@
740	740
741	741	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
742	742
	757	+
	758	+
743	743	=== 3.4.1 Common Commands ===
744	744
745	745	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]
746	746
747	747
	764	+
748	748	=== 3.4.2 Sensor related commands ===
749	749
750	750	==== 3.4.2.1 Set Transmit Interval ====
...	...	@@ -768,6 +768,7 @@
768	768	)))
769	769
770	770
	788	+
771	771	==== 3.4.2.2 Set Work Mode (AT+MOD) ====
772	772
773	773	Set work mode.