Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -275,6 +275,7 @@
275	275	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
	278	+
278	278	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
279	279
280	280	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -282,6 +282,8 @@
282	282	[[image:image-20220523174024-3.png]]
283	283
284	284	(((
	286	+
	287	+
285	285	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
286	286	)))
287	287
...	...	@@ -311,7 +311,6 @@
311	311	* [1] RO1 relay channel is close and the RO1 LED is ON.
312	312	* [0] RO2 relay channel is open and RO2 LED is OFF;
313	313
314		-
315	315	**LT22222-L:**
316	316
317	317	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -328,7 +328,6 @@
328	328	** DO1 LED is off in both case
329	329
330	330
331		-
332	332	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
333	333
334	334
...	...	@@ -654,6 +654,7 @@
654	654
655	655	Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
656	656
	658	+
657	657	**Example:**
658	658
659	659	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
...	...	@@ -683,6 +683,7 @@
683	683	Same as AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
684	684
685	685
	688	+
686	686	**Example2**: AA 02 01 00
687	687
688	688	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
...	...	@@ -701,6 +701,8 @@
701	701
702	702	* Each bits shows if the corresponding trigger has been configured.
703	703
	707	+
	708	+
704	704	**Example:**
705	705
706	706	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -712,6 +712,8 @@
712	712
713	713	* Each bits shows which status has been trigger on this uplink.
714	714
	720	+
	721	+
715	715	**Example:**
716	716
717	717	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -723,6 +723,8 @@
723	723
724	724	* Each bits shows which status has been trigger on this uplink.
725	725
	733	+
	734	+
726	726	**Example:**
727	727
728	728	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -765,6 +765,7 @@
765	765	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
766	766
767	767
	777	+
768	768	=== 3.4.1 Common Commands ===
769	769
770	770	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]