Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -275,6 +275,7 @@
275	275	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
	278	+
278	278	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
279	279
280	280	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -282,6 +282,8 @@
282	282	[[image:image-20220523174024-3.png]]
283	283
284	284	(((
	286	+
	287	+
285	285	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
286	286	)))
287	287
...	...	@@ -295,6 +295,7 @@
295	295
296	296	For example if payload is: [[image:image-20220523175847-2.png]]
297	297
	301	+
298	298	**The value for the interface is:  **
299	299
300	300	AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V
...	...	@@ -311,6 +311,7 @@
311	311	* [0] RO2 relay channel is open and RO2 LED is OFF;
312	312
313	313
	318	+
314	314	**LT22222-L:**
315	315
316	316	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -620,11 +620,14 @@
620	620	* **AT+MOD=1 ** **~-~->** The normal working mode
621	621	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
622	622
	628	+
623	623	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
624	624
625	625	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
626	626	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
627	627
	634	+
	635	+
628	628	**AT Command to set Trigger Condition**:
629	629
630	630	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -638,6 +638,7 @@
638	638	AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
639	639
640	640
	649	+
641	641	(% style="color:#4f81bd" %)**Trigger base on current**:
642	642
643	643	Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
...	...	@@ -647,6 +647,7 @@
647	647	AT+ACLIM=10000,15000,0,0   (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
648	648
649	649
	659	+
650	650	(% style="color:#4f81bd" %)**Trigger base on DI status**:
651	651
652	652	DI status trigger Flag.
...	...	@@ -653,12 +653,13 @@
653	653
654	654	Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
655	655
	666	+
656	656	**Example:**
657	657
658	658	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
659	659
660	660
661		-**Downlink Command to set Trigger Condition**
	672	+**Downlink Command to set Trigger Condition:**
662	662
663	663	Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
664	664
...	...	@@ -687,6 +687,7 @@
687	687	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
688	688
689	689
	701	+
690	690	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
691	691
692	692	MOD6 Payload : total 11 bytes payload
...	...	@@ -700,6 +700,8 @@
700	700
701	701	* Each bits shows if the corresponding trigger has been configured.
702	702
	715	+
	716	+
703	703	**Example:**
704	704
705	705	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -711,6 +711,8 @@
711	711
712	712	* Each bits shows which status has been trigger on this uplink.
713	713
	728	+
	729	+
714	714	**Example:**
715	715
716	716	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -722,6 +722,8 @@
722	722
723	723	* Each bits shows which status has been trigger on this uplink.
724	724
	741	+
	742	+
725	725	**Example:**
726	726
727	727	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -764,6 +764,7 @@
764	764	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
765	765
766	766
	785	+
767	767	=== 3.4.1 Common Commands ===
768	768
769	769	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]