Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -275,6 +275,7 @@
275	275	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
	278	+
278	278	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
279	279
280	280	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -282,6 +282,8 @@
282	282	[[image:image-20220523174024-3.png]]
283	283
284	284	(((
	286	+
	287	+
285	285	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
286	286	)))
287	287
...	...	@@ -295,6 +295,7 @@
295	295
296	296	For example if payload is: [[image:image-20220523175847-2.png]]
297	297
	301	+
298	298	**The value for the interface is:  **
299	299
300	300	AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V
...	...	@@ -310,7 +310,6 @@
310	310	* [1] RO1 relay channel is close and the RO1 LED is ON.
311	311	* [0] RO2 relay channel is open and RO2 LED is OFF;
312	312
313		-
314	314	**LT22222-L:**
315	315
316	316	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -327,7 +327,6 @@
327	327	** DO1 LED is off in both case
328	328
329	329
330		-
331	331	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
332	332
333	333
...	...	@@ -711,6 +711,8 @@
711	711
712	712	* Each bits shows which status has been trigger on this uplink.
713	713
	716	+
	717	+
714	714	**Example:**
715	715
716	716	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -722,6 +722,8 @@
722	722
723	723	* Each bits shows which status has been trigger on this uplink.
724	724
	729	+
	730	+
725	725	**Example:**
726	726
727	727	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -764,6 +764,7 @@
764	764	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
765	765
766	766
	773	+
767	767	=== 3.4.1 Common Commands ===
768	768
769	769	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]