Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -275,6 +275,7 @@
275	275	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
	278	+
278	278	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
279	279
280	280	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -282,6 +282,8 @@
282	282	[[image:image-20220523174024-3.png]]
283	283
284	284	(((
	286	+
	287	+
285	285	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
286	286	)))
287	287
...	...	@@ -295,6 +295,7 @@
295	295
296	296	For example if payload is: [[image:image-20220523175847-2.png]]
297	297
	301	+
298	298	**The value for the interface is:  **
299	299
300	300	AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V
...	...	@@ -310,7 +310,6 @@
310	310	* [1] RO1 relay channel is close and the RO1 LED is ON.
311	311	* [0] RO2 relay channel is open and RO2 LED is OFF;
312	312
313		-
314	314	**LT22222-L:**
315	315
316	316	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -652,12 +652,13 @@
652	652
653	653	Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
654	654
	658	+
655	655	**Example:**
656	656
657	657	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
658	658
659	659
660		-**Downlink Command to set Trigger Condition**
	664	+**Downlink Command to set Trigger Condition:**
661	661
662	662	Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
663	663
...	...	@@ -686,6 +686,7 @@
686	686	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
687	687
688	688
	693	+
689	689	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
690	690
691	691	MOD6 Payload : total 11 bytes payload
...	...	@@ -699,6 +699,8 @@
699	699
700	700	* Each bits shows if the corresponding trigger has been configured.
701	701
	707	+
	708	+
702	702	**Example:**
703	703
704	704	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -710,6 +710,8 @@
710	710
711	711	* Each bits shows which status has been trigger on this uplink.
712	712
	720	+
	721	+
713	713	**Example:**
714	714
715	715	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -721,6 +721,8 @@
721	721
722	722	* Each bits shows which status has been trigger on this uplink.
723	723
	733	+
	734	+
724	724	**Example:**
725	725
726	726	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -763,6 +763,7 @@
763	763	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
764	764
765	765
	777	+
766	766	=== 3.4.1 Common Commands ===
767	767
768	768	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]