Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -275,6 +275,7 @@
275	275	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
	278	+
278	278	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
279	279
280	280	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -282,6 +282,8 @@
282	282	[[image:image-20220523174024-3.png]]
283	283
284	284	(((
	286	+
	287	+
285	285	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
286	286	)))
287	287
...	...	@@ -295,6 +295,7 @@
295	295
296	296	For example if payload is: [[image:image-20220523175847-2.png]]
297	297
	301	+
298	298	**The value for the interface is:  **
299	299
300	300	AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V
...	...	@@ -326,7 +326,6 @@
326	326	** DO1 LED is off in both case
327	327
328	328
329		-
330	330	=== 3.3.2 AT+MOD~=2, (Double DI Counting) ===
331	331
332	332
...	...	@@ -619,7 +619,6 @@
619	619	* **AT+MOD=1 ** **~-~->** The normal working mode
620	620	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
621	621
622		-
623	623	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
624	624
625	625	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
...	...	@@ -626,6 +626,7 @@
626	626	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
627	627
628	628
	631	+
629	629	**AT Command to set Trigger Condition**:
630	630
631	631	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -639,6 +639,7 @@
639	639	AT+AVLIM=5000,0,0,0   (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
640	640
641	641
	645	+
642	642	(% style="color:#4f81bd" %)**Trigger base on current**:
643	643
644	644	Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
...	...	@@ -648,6 +648,7 @@
648	648	AT+ACLIM=10000,15000,0,0   (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
649	649
650	650
	655	+
651	651	(% style="color:#4f81bd" %)**Trigger base on DI status**:
652	652
653	653	DI status trigger Flag.
...	...	@@ -654,12 +654,13 @@
654	654
655	655	Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
656	656
	662	+
657	657	**Example:**
658	658
659	659	AT+ DTRI =1,0   (Enable DI1 trigger / disable DI2 trigger)
660	660
661	661
662		-**Downlink Command to set Trigger Condition**
	668	+**Downlink Command to set Trigger Condition:**
663	663
664	664	Type Code: 0xAA. Downlink command same as AT Command **AT+AVLIM, AT+ACLIM**
665	665
...	...	@@ -688,6 +688,7 @@
688	688	Same as AT+ DTRI =1,0  (Enable DI1 trigger / disable DI2 trigger)
689	689
690	690
	697	+
691	691	(% style="color:#4f81bd" %)**Trigger Settings Payload Explanation:**
692	692
693	693	MOD6 Payload : total 11 bytes payload
...	...	@@ -702,6 +702,7 @@
702	702	* Each bits shows if the corresponding trigger has been configured.
703	703
704	704
	712	+
705	705	**Example:**
706	706
707	707	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -714,6 +714,7 @@
714	714	* Each bits shows which status has been trigger on this uplink.
715	715
716	716
	725	+
717	717	**Example:**
718	718
719	719	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -726,6 +726,7 @@
726	726	* Each bits shows which status has been trigger on this uplink.
727	727
728	728
	738	+
729	729	**Example:**
730	730
731	731	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.