Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -275,6 +275,8 @@
275	275	* **MOD5**: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
276	276	* **ADDMOD6**: Trigger Mode, Optional, used together with MOD1 ~~ MOD5
277	277
	278	+
	279	+
278	278	=== 3.3.1 AT+MOD~=1, 2ACI+2AVI ===
279	279
280	280	The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by default.
...	...	@@ -282,6 +282,8 @@
282	282	[[image:image-20220523174024-3.png]]
283	283
284	284	(((
	287	+
	288	+
285	285	(% style="color:#4f81bd" %)**DIDORO**(%%) is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
286	286	)))
287	287
...	...	@@ -295,6 +295,7 @@
295	295
296	296	For example if payload is: [[image:image-20220523175847-2.png]]
297	297
	302	+
298	298	**The value for the interface is:  **
299	299
300	300	AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V
...	...	@@ -310,6 +310,7 @@
310	310	* [1] RO1 relay channel is close and the RO1 LED is ON.
311	311	* [0] RO2 relay channel is open and RO2 LED is OFF;
312	312
	318	+
313	313	**LT22222-L:**
314	314
315	315	* [1] DI2 channel is high input and DI2 LED is ON;
...	...	@@ -619,13 +619,11 @@
619	619	* **AT+MOD=1 ** **~-~->** The normal working mode
620	620	* **AT+ADDMOD6=1**   **~-~->** Enable trigger
621	621
622		-
623	623	LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
624	624
625	625	1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command). This uplink uses LoRaWAN (% style="color:#4f81bd" %)**unconfirmed**(%%) data type
626	626	1. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above settings). Both Uplinks use LoRaWAN (% style="color:#4f81bd" %)**CONFIRMED data type.**
627	627
628		-
629	629	**AT Command to set Trigger Condition**:
630	630
631	631	(% style="color:#4f81bd" %)**Trigger base on voltage**:
...	...	@@ -701,7 +701,6 @@
701	701
702	702	* Each bits shows if the corresponding trigger has been configured.
703	703
704		-
705	705	**Example:**
706	706
707	707	10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
...	...	@@ -713,7 +713,6 @@
713	713
714	714	* Each bits shows which status has been trigger on this uplink.
715	715
716		-
717	717	**Example:**
718	718
719	719	10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
...	...	@@ -725,7 +725,6 @@
725	725
726	726	* Each bits shows which status has been trigger on this uplink.
727	727
728		-
729	729	**Example:**
730	730
731	731	00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
...	...	@@ -768,7 +768,6 @@
768	768	* (% style="color:#4f81bd" %)**Sensor Related Commands**(%%): These commands are special designed for LT-22222-L.  User can see these commands below:
769	769
770	770
771		-
772	772	=== 3.4.1 Common Commands ===
773	773
774	774	They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware v1.5.4, user can find what common commands it supports: [[End Device AT Commands and Downlink Command>>doc:Main.End Device AT Commands and Downlink Command.WebHome]]